Search Documents

By John Riegle

To date. utility company underground storage of gas has generally been restricted to depleted dry gas fields. The Playa del Rey project is probably the first to successfully store gas in a partially depleted oil reservoir with the recovery of large volumes of pas at high rates as the main objective. Oil recovery has been a secondary consideration. Problems encountered unusual to those of storage in a dry gas zone were: (1) the removal and retardation of formation of emulsion. (2) the upstructure movement of fluid during withdrawal periods which formed fluid blocks, and (3) reservoir shrinkage resulting from encroachment of edgewater. The solution of these problems as outlined in the paper has resulted in increasing the withdrawal rate from the original design capacity of 4,000 Mcf per hour to the current 10.000 Mcf per hour. Additional increase is anticipated as the operations continue. Migration. reservoir performance. operational procedure and a historical record are included to make this a resume of the project from its war-time inception in 1942 to the first of 1952. INTRODUCTION The Playa del Rey underground gas storage project is probably the first project in which gas has been stored in a partially depleted oil reservoir, with the recovery of large volumes of gas at high rates as the main objective and the recovery of oil a secondary consideration. Problems unusual to those of storage in dry gas zones have made this a pioneer endeavor. The total storage capacity of approximately 1,500,000 Mcf of this reservoir is small in comparison with other underground gas storage projects. However. by study and experiment the deliverability into transmission lines. operating at pressures in excess of 150 lbs., has been nearly tripled in the past three years. to the current 10.000 Mcf per hour late, without the use of compression. It is anticipated this rate will gradually increase as additional fluid is removed from the formation. LOCATION AND HISTORY Playa del Key is located on Santa Monica Bay about two miles south of the beach commuity of Venice and 15 miles southwest of the renter of the City city Los Angeles. Fig. 1. The discovery well was completed at 6,194 ft in 1929. An upper zone at 3,905 ft was found on June 18. 1930. Townlot development was very rapid and by the end of 1930 there were 141 producing wells in the field. The Union Oil Co. completed a lower zone well south of the Townlot Field in May, 1931, which was believed to be an extension, until additional drilling of about 50 wells during 1934 and 1935 indicated this area to be a separate accumulation as shown on Fig. 2. The lower oil horizon, which is now the storage zone, had no original gas cap and is believed to be a continental detrital deposit of conglomerate that accumulated in valleys and depressions of a weathered schist high. which later subsided and was overlain by an impervious nodular shale. This type of formation has rapid variation of porosity. permeability and thickness due to lack of sorting action common to marine deposition. and the uneven surface of the original schist high. Production was limited on the upstructure sides by the pinching out of the conglomerate, and downstructure by edgewater. Unrestricted production, together with high permeabilities, led to large wastage of gas from this new area as facilities were not available for transport of gas to market. The decline was very rapid and by 1942 the portion of the new area south of Ballona Creek was nearly depleted. ACQUISITION OF PROPERTY The rapid increase in industrialization of Southern California during World war 11 forced upon the local gas com-

Jan 1, 1953

By F. S. Crawford

This study was made to find methods of preventing back strains, among workers in brick plants, however, the information should apply to other industries that employ hand labor too process materials. The report is based on information in letters from. Bureau of Mines engineers and other safety men in the United States who visited numerous brick plants. Back strains, as wall as hernias and other muscular strains, result when certain body structures are subjected to strains greater than, they can withstand. Such breakdowns may be prevented simply by not straining these body structures. This is simple in theory but complicated in practice. It requires primary education of new workers and reeducation of older workers in the best method of lifting, preemployment physical. examinations to select employees for the jobs that require constant lifting, all possible mechanization of material-handling operations, relocation of machinery, and elevation of working surfaces to reduce to a minimum the muscular effort the workers must exert to perform operations impossible to mechanize. Accidents of any kind are a total bee for the American economy and decrease productivity; whereas mechanization raises the level of productivity and constitutes progress toward total safety. Heavy lifting should be done mechanically whenever possible, saving the men to direct the machines. This is an essential step in preventing strain accidents.

Jan 1, 1953

By Strathmore R. B. Cooke, Thomas E. Bam

The paper discusses the mineralogy, structure, and strength of magnetite pellets fired in air and in a neutral atmosphere at various temperatures. The information obtained from this investigation is used to explain the origin of the structures occurring in pellets produced by pilot-plant operation. MUCH experimental work has been performed on i-VL the mechanism of agglomeration and pelletiz-ing of moist ore and concentrates and on the process of firing agglomerates, but except for the work of Tigerschiold and Ilmonil much of the published information is empirical, and the literature contains no information concerning the structure of fired pellets. Results of a preliminary study of the micro-structures occurring in pellets produced both in the laboratory and on a pilot-plant scale are presented in this paper. Most of the results were obtained from pellets prepared from Mesabi magnetic taconite, but through the courtesy of the staffs of the Minnesota Mines Experiment Station and the Bethlehem Steel Co., fired pellets produced from limonite and hematite ores and from Lebanon magnetite have also been examined. The work has been restricted almost entirely to pellets produced without additives, the exceptions being those in which coal was added to the filter cake before rolling. Schwartz has described the microstructures occurring in ore sinters produced under reducing conditions.' Many of the structures and constituents he describes are common to fired pellets, but the constituents normally occur in markedly different proportions. His statement that "in all satisfactory sinter the amount of hematite is small, perhaps not over 2 or 3 per cent" is inapplicable to pellets produced by pilot plant operation or by any process in which air is not deliberately excluded. Pilot plant pellets contain over 90 pct by weight of hematite, and those produced in the smaller furnaces of the Minnesota Mines Experiment Station contain more than 80 pct of that constituent. Preparation of Specimens It is difficult to examine unfired pellets microscopically because of their insufficient coherency to withstand sectioning and polishing. Fired pellets sometimes lack coherency and frequently contain holes which are troublesome during polishing. Impregnation of both air-dried and fired pellets is readily accomplished by the use of methyl metha-crylate monomer." The dry pellets are covered in a test tube with excess monomer, to which a small amount of accelerator has been added. When the test tube is placed in a cooling bath and evacuated with an aspirator, most of the entrapped air is removed, and disruption of weak pellets by boiling of the monomer is reduced to a minimum. Polymerization is then effected by immersion of the test tube in a water-bath at about 45"C, this temperature being held for 4 or 5 days. The test tube may then be broken away from the solidified mass and the pellets sectioned by a carborundum wheel or a diamond saw. Where time is important, impregnation is carried out at a higher temperature by Meyer's method.' Air-dried pellets must be impregnated with especial care; otherwise swelling occurs and the solids are displaced. It is more important to be certain that the monomer forms a reasonably complete network throughout the specimen than that all entrained air is removed, and for this reason the vacuum technique may be omitted. Impregnated agglomerated products and pellets are extremely coherent, section well, and may be polished either by hand or by machine. Hand polishing is not satisfactory for the examination of conditions existing at the boundaries of grains, and for this machine polishing must be used. The Graton-Vanderwilt machine gives excellent results, provided that pressure on the specimen is considerably in excess of that recommended by the manufacturer. Mineralogy of Fired Pellets Only two opaque iron minerals, magnetite and hematite, have been recognized in pellets. The complete identity of, these artificial minerals with their corresponding natural counterparts is shown by their mineralographic characteristics and their X-ray structures. Wiistite has not been found. Slag is the most common transparent constituent of fired pellets. Occasionally conditions have been appropriate for the crystallization of fayalite from the slag, and at other times another crystalline sil-

Jan 1, 1953

By James W. Townsend

[The Harrington-Hickory mine in the Star raining district, Beaver County, Utah, has produced approximately 20,000 tons of lead-zinc-silver ores since 1910. Production previous to 1910 is not known. The mine is owned by the New Majestic Mining Co. The property was rehabilitated and operated by James D. Williams under a 10-year lease with option to purchase from April 1943 to May 1949, Loans from the Reconstruction Finance Corporation in the aggregate of $41,000 wore used in construction of an access road, rehabilitation of the mine, and purchase of equipment for full-scale operation. The improved, all-weather access road extends from loading ramps on the Union Pacific Railroad at Milord to the urine storage bins 5 miles west o f town. The mine is serviced electrically by a. 5,000-volt line owned by Telluride Power Co. Mine transformers step the voltage down to 440/220/110 for surface and underground service.]

Jan 1, 1953

By J. J. Arps

This paper is a study of the effect of temperature on the electrical resistivity of sodium chloride solutions based on the published resistivity and density data in the International Critical Tables. This temperature effect is of considerable importance in quantitative interpretation of electric logs, where it is frequently necessary to correct mud resistivities measured under surface conditions to temperatures existing at the bottom of the bore hole. An empirical approximation formula was developed for this conversion which has proved to be very useful and seems to provide results well within the range of accuracy of the data involved. This approximation formula states: sistivities of sodium chloride solutions at temperatures of t and t degrees Fahrenheit, respectively. INTRODUCTION Research by various investigators during the past 20 years has clarified the physical principles of the phenomena which cause the natural or spontaneous electric potential in rotary drilled bore holes. The basic relationship which is most commonly used reads: in which the SP deflection, as measured from the shale base line, is expressed in millivolts. K is a constant, which appears to vary between 50 and 110; the low value applying to shaly sands, whereas the higher values are more common in carbonate rocks. A good average value for K = 70. for which value there is considerable theoretical justification." In order to calculate the resistivity of the connate water R and to estimate its "equivalent salinity" (as NaCl) from an electric log by means of this SP relationship from a knowledge of the static self potential and of the resistiv- ity of the mud filtrate R it is necessary to first correct the resistivity of the mud filtrate measured under surface conditions to the resistivity of this same mud filtrate in the well bore at a different temperature. In order to make this temperature conversion for the mud filtrate the variation of the electrical resistivity of sodium chloride solutions with temperature is commonly used. Since some discrepancies were found in the charts ordinarily used for this purpose, it was felt desirable to make a new study of this relationship based on the published measurement data. Because of the fundamental nature of these relationships and as an aid to other workers in this field, an attempt has been made in this study to show every step in the calculations. CONDUCTIVITY VS MOL CONCENTRATION The most complete published reference on the temperature relationship of sodium chloride solutions of different concentrations is provided in the International Critical Tables.' The basic measurement data on the electrical conductivity of aqueous sodium chloride solutions, at different temperatures, as given in these tables, are reproduced in Table 1. The electrical conductivity values in this Table 1 are expressed as 10' times the specific conductivity k in ohm-'cm'l per unit of concentration in milligram mols per liter of solution C, or: RESISTIVITY VS MOL CONCENTRATION These conductivity values from Table 1 were first converted to the corresponding electrical resistivity values (R) , expressed in ohm-meters, as is conven-

Jan 1, 1953

By D. K. Das, P. A. Beck, S. P. Rideout

IN a previous publication1 1200°C isothermal phase diagram sections were given for the Cr-CO-Ni, Cr-Co-Fe, Cr-Co-Mo, and Cr-Ni-Mo ternary systems, in which the a phase formed narrow, elongated solid solution fields. The present investigation is concerned with the 1200°C isothermal sections of the Co-Ni-Mo, Co-Fe-Mo, and Ni-Fe-Mo ternary systems. A prominent feature of these systems is the presence of narrow, elongated µ phase fields. The crystal structure of the phase designated as µ both here and in the previous publication1 was determined by Arnfelt and Westgren.2 For the (CO, W)µ phase, named by them Co,W, (and also frequently designated as a), these authors found that the crystal system is hexagonal-rhombohedra1 and the space group is D53d — R3,. Westgren and Mag-neli3 later found that isomorphous phases exist in the Fe-W and the Fe-Mo systems (these phases are often referred to as < and E, respectively). Henglein and Kohsok4 stated that the phase described by them as Co7Mo,; (otherwise frequently designated as c) is also isomorphous with the above three. The Co-Fe-Mo system was investigated at 1300°C by Koester and Tonn,5 who found a continuous series of solid solutions between (Co, MO)µ and (Fe, MO)µ Koester6 also indicated similar uninterrupted solid solutions in the Ni-Fe-Mo system. However, since the Ni-Mo binary system does not have a phase isomorphous with F, Koester&apos;s diagram is expected to be erroneous. No data appear to be available in the literature concerning the Co-Ni-Mo system. The face-centered cubic (austenitic) solid solut,ions of iron, nickel, and cobalt, which are quite extensive in all three systems at 1200°C, are here designated as the a phase. The body-centered cubic (ferritic) solid solutions, based on iron, are designated in this report as the ? phase, in conformity with the nomenclature used previously.&apos; Experimental Procedure The alloys were prepared by vacuum induction melting in zirconia and alumina crucibles. The lot analyses for the metals used have been given.&apos; The number of alloys prepared was 46 for the Co-Ni-Mo system, 65 for the Co-Fe-Mo system, and 113 for the Ni-Fe-Mo system. The compositions of these alloys were selected with due regard to maximum usefulness in locating phase boundaries. The alloy specimens were annealed at 1200°C in an atmosphere of purified 92 pct helium and 8 pct hydrogen mixture. Alloys consisting almost entirely of the face-centered cubic austenitic a phase, or of the body-centered cubic ferritic c phase were double-forged with intermediate annealing. The double-forged specimens were then final annealed for 90 hr at 1200 °C and quenched in cold water. Alloys containing considerable amounts of any of the other phases could not be forged. Such specimens were annealed for 150 hr at 1200°C and quenched. Microscopic specimens of all alloys were prepared by mechanical polishing, in many cases followed by electrolytic polishing. Description of the polishing and etching procedures used and tabulation of the intended compositions of the alloys prepared are being published in two N.A.C.A. Technical Notes.7,8 , Many of the alloys were analyzed chemically and, in general, the results are in excellent agreement with the intended compositions. X-ray diffraction samples were prepared by filing or crushing homogenized alloy specimens and by reannealing the obtained powders in evacuated and sealed quartz tubes. After annealing for 30 min at 1200°C the tubes were quenched into cold water. X-ray diffraction patterns were made with unfiltered chromium radiation at 30 kv, using an asymmetrical focusing camera of high dispersion. X-ray diffraction and microscopic methods were used jointly to identify the phases present in each specimen. The amounts of the phases in each alloy were estimated microscopically. The phase boundaries were located by the disappearing phase method. The results were used to construct 1200°C isothermal sections for the three ternary phase diagrams. The accuracy of the location of the phase boundaries determined in this manner is estimated to approximately ±1 pct of each component. The portion of the three phase diagrams lying between the µ, P, and 6 phases on the one hand, and the molybdenum corner on the other, has not been investigated. Recently Metcalfe reported0 a high temperature allotropic form of cobalt on the basis of dilatometric results and of cooling curves. In the present work no attempt was made to search for the new phase in the cobalt corner of the Co-Fe-Mo and Co-Ni-Mo systems. No alloy was prepared with more than 80 pct Co; the alloys used were intended to locate the boundary of the a phase saturated with cL. The microstructures of the quenched a alloys near the cobalt COrner gave no suggestion of an in-suppressible transformation On quenching. The location of the boundaries of the a + ? two-phase fields in the Fe-Ni-Mo and Fe-CO-MO systems was determined entirely by the microscopic method. The face-centered cubic a alloys near the ? field transform partially or wholly into the body-centered cubic ? phase on quenching from 1200°C to room temperature. The ? formed in this manner has an

Jan 1, 1953

By C. O. Lee, Z. W. Bartlett, R. H. Feierabend

DESPITE the fact that American brimstone production has increased 2 times since the prewar period 1935-1939, the demand for sulphur exceeds the supply. To alleviate this situation efforts are being made to increase the production of sulphur and bring the shortage to an end. The most important developments are being undertaken on the Gulf Coast. One new brimstone mine has been put into operation and three others are being developed. These projects are expected to account for a large part of the additional sulphur production now anticipated for the free world.&apos;.&apos; Except for a small amount of byproduct sulphur from sour natural gas and refinery gases, American brimstone is produced by the same process devised by Frasch 60 years ago, consisting essentially of the injection of superheated water at about 325°F into sulphur-bearing formations through wells which are drilled from the surface by standard oilfield methods. Sulphur deposits vary in depth from a few hundred feet to 2500 ft from the surface; in a typical deposit the sulphur occurs as crystalline aggregates in porous limestone and gypsum in concentrations varying from 5 to 40 pct, the thickness of the formation ranging from a few feet to several hundred.3 The deposits are usually surrounded by formations impermeable to the flow of hot water, the top and sides being enclosed by impermeable sediments and the bottom by dense impermeable anhydrite. As the hot water leaves the well bore, it percolates through the formation and transmits its heat to the rock and sulphur. When the sulphur reaches 240°F it melts, separates from the rock, and flows through the hot channels downward to the bottom of the well. Here it is freed from incoming water and from formation water, which saturates the porous rock, by gravity separation, liquid sulphur being 1.8 times as heavy as water. It then is pumped to the surface in a relatively pure state, 99.5 pct or better. Chief contaminants are organic impurities, such as petroleum residues, which are soluble in sulphur and tend to discolor it.&apos; Sixteen deposits of commercial magnitude have been discovered in the Gulf Coast area. Five of these deposits have been depleted and abandoned with production totalling more than 26,886,000 tons. Eight properties are operating and have produced 65,875,-000 tons to Jan. 1, 1952, for a total Frasch-type production of 92,761,000 tons. Three new deposits are under development. Aforementioned deposits are listed in Table I. Each of these deposits has been found in the cap-rock overlying shallow intrusive salt plugs or domes and buried in several hundred to as much as 2500 ft of sediments. All salt domes do .not contain sulphur; only 16 sulphur deposits have been found in a total of 231 salt domes which are known to exist in the Gulf Coastal states of Texas, Louisiana, Mississippi, and Alabama. Ten of the salt domes lie in the Gulf of Mexico offshore from the Texas and Louisiana coasts. Additional offshore domes may be found, but their value as a sulphur potential is questionable owing to the great hazard and high cost that can be visualized at these exposed locations where depths of water reach 50 ft. Marsh operations of Freeport Sulphur Co. are in the southeast section of Louisiana. In general, the country is low, flat, relatively uninhabited marshland broken by many shallow lakes and bayous which extend for irregular distances inland. Geologically, the coastal area is of sedimentary origin, having been built up gradually under the sea by deposition of material carried down by large streams to their deltas. Offshore bars were formed enclosing

Jan 1, 1953

By Walter C, Smith

Metallic bismuth was known in the Middle Ages and the name is supposed to come from the German Wismut. The origin of the German name is uncertain. References to bismuth are found in the writings of Valentine, Paracelsus, and Agricola between 1450 and 1550. Early specimens of bismuth were very impure and often were confused with antimony, tin, and zinc. About the middle of the eighteenth century, J. H. Pott, C. J. Geoffroy, and Torbern Bergman succeeded in producing fairly pure bismuth and showed it to be an elementary metal similar in many respects to lead.

Jan 1, 1953

By L. L. Newman

PUBLIC UTILITY GAS PRODUCTION IN 1802, William Murdock first used retort coal gas to light his house and the Boulton and Watt plant where he was employed. For the next three quarters of a century coal served as the principal raw material for the manufacture of city gas for general distribution. Coal continued to hold its predominant position for another half century after Prof. Thaddeus C. Lowe developed the first practical method of enriching water gas with cracked-oil vapors in an integrated operation. This position, however, was no longer maintained through the medium of direct carbonization of coal in retorts but as a result of using anthracite or coke as the generator fuel in carburretted water-gas machines. The early water-gas machines were extremely crude and the consumption of both oil and generator fuel was very high. However, the cost of installation was considerably lower than for any coal-gas system having the equivalent gas-making capacity, the labor involved was small, and the water-gas machine could be started up and shut down quickly. It thus proved very useful as standby equipment and in taking peak loads from the coal-gas plants. The flexibility of the water-gas machine, furthermore, made it possible to change the candlepower of the gas readily to suit the required conditions. Later, when calorific value replaced candlepower as the standard of gas quality, the water-gas machine was found to be equally flexible in keeping the city gas under complete and convenient control. No basic improvements were made in the Lowe carburetted water-gas process until 1898, when means were added to provide for regular reversals of the flow of steam through the fuel bed. By judicious proportioning of the quantities of up-run and down-run steam, it became possible for the operator to control the hardness and position of the clinker to a degree that previously had been unattainable. Also in 1898, the first by-product coke plant in America to supply city gas was built at Everett, Massachusetts. Later many other by-product plants, of greatly improved design and capacity, were built, but not primarily for city-gas production, chiefly because of the relatively high investment cost per unit of gas made. Cheaper plant construction has been the subject of serious study, and some progress is expected, but other factors, such as plant life,

Jan 1, 1953

AIME 1953 DIRECTORY SUPPLEMENT OFFICERS AND COMMITTEES OF LOCAL SECTION; COUNCIL OF SECTION DELEGATES Linwood Thiessen, Chairman H. D. Vaughan, Vice-Chairman John H. Melvin, Secretary EXECUTIVE COMMITTEE L. E. Thelin, Connecticut J. B. Cunningham, Arizona W. L. Penick, San Francisco G. L. Yates, Kansas DELEGATES Adirondack - C. DeWitt Smith &apos;54 Alaska - Robert 11. Chapman, ?54 Arizona J. B. Cunningham, &apos;53 Black Hills - Sidney M. Runke, &apos;54 Boston -R&apos;. Schuhmann, Jr. ?54 Carlsbad Potash - W. P. Wilson, &apos;54 Central Appalachian - Charles T. Holland, &apos;54 Chicago - H. A. White, &apos;54 Cleveland - Milton Tilley, &apos;54 Colorado - J. Paul Harrison &apos;54 Columbia - Harold Kirkemo, &apos;54 Connecticut - Lewis E. Thelin, ?53 Dallas - Kenneth F. Anderson, &apos;54 Delta - Roy S. Sullins &apos;54 Detroit - F. P. Bens, &apos;53 East Texas - Joseph A. Morris, &apos;54 El Paso Metals - E. M. Thomas, &apos;54 Florida - W. O. McClintock &apos;54 Fort Worth - Ray Elner, &apos;51 Gulf Coast - H. E. Treichler, &apos;53 Kansas - G. L. Yates, &apos;53 Lehigh Valley - H. R. Gault &apos;54 Lima, Peru - R. P. Koenig, ?54 Lou-Ark - A. H. Crawford. &apos;53 Mexico - W. G. Kane, &apos;54 Mid-Continent - J. H. Beesley, &apos;53 Minnesota - J. R. Stuart, &apos;54 Montana - F. W. Strandberg, &apos;53 Nevada - Albert Silver,&apos;53 New York - P. Malozemoff, &apos;54 North Pacific - A. H. Mellish, &apos;54 North Texas - K. F. Anderson, &apos;54 Chio Valley - J. H. Melvin, ?53 Oklahoma City - Charles Miller, &apos;53 Oregon - T. C. Matthews, &apos;54 Penn. Anthracite - D. C. Helms, &apos;54

Jan 1, 1953

By W. Shockley

THIS lecture can best begin with a statement of the chief conclusion: The metallurgical industry will find profit in supporting fundamental research on dislocations. This support should be done both in their own laboratories and in universities. My lecture consists of an exposition of the basis for this conclusion. The experience on which I base it is drawn largely from two fields in solid state physics—one field is transistor electronics and the other is dislocation theory. At present the relationship of solid state physics to technology is different in these two fields. In electronics without question, the physics has led the technology. In metallurgy, on the other hand, the technology in the form of metallurgical art is far ahead of the fundamental science. In transistor electronics, physics has suggested and can still suggest previously unachieved combinations of matter that will have new and useful properties; that is, the physicist can make specific predictions. The physicist can also have some confidence that the predicted devices will actually come into existence in a matter of months or years and that they will live up to the predictions. In metallurgy, the physicist cannot to a comparable degree make predictions and have the same hope that they will lead to something new and valuable. There are a number of reasons for this difference. The first is simply historical. Transistor physics is young. It may be regarded as dating from the announcement of the transistor, in which case it is about four years old, or from the first real control of semiconductors as materials (this was accomplished largely by metallurgists, by the way) in which case it is about ten years old. Metallurgical art, on the other hand, is thousands of years old. There is no doubt that the advance of this art has been and will be hastened by a good fundamental understanding of the quantum theory of atomic phenomena. It, is too much to expect, however, that theory will soon catch up with the lead that practice has gained in a thousand years, and that theory will then point out specific pathways to better materials. It seems more probable that modern atomic theory will serve to interpret and organize information much as thermodynamics has done through phase diagrams. In this lecture, I shall emphasize an important feature common to both solid state electronics and to metallurgy. This common feature is the harmonizing principle that justifies discussing electronics and metallurgy as related topics in solid state physics. In both cases the important properties of the materials arise from imperfections. By imper- fections I mean deviations of the materials from perfect single crystals. The imperfections may be of many forms. From the point of view of utility they may be either good or bad, and a given type may be good or bad depending on circumstances. The technical material of my lecture will be divided into two parts. The first will be chiefly concerned with four types of imperfections in germanium crystals. The control of these imperfections makes possible the fabrication of useful electronic devices. A good example of such control is the junction transistor, which I shall discuss from this viewpoint later. The junction transistor, as some of you may have heard, can be used as an amplifier of electrical signals and in a number of respects surpasses what has hitherto been achieved with vacuum tubes. The second part of my technical material will be concerned with dislocations. For about fifteen years the theoretical physicist has had dislocations in mind as the most important kind of imperfection in metals. He has, however, until recently had experimental material of a highly speculative nature to back up his assertions. I am fortunate in the timing of this lecture to be able to describe some recent results that put dislocations on a far more definite basis than has been the case in the past. In fact there are now some experiments which reveal the characteristic properties of dislocations almost as clearly as experiments in transistor physics reveal the properties of holes and electrons, properties that I shall soon describe. It is this advance in the status of dislocations that emboldened me to make my initial assertion that the metallurgical industry will profit from supporting fundamental research on dislocations. Transistor Electronics In order to discuss imperfections in semiconductors, it is necessary to visualize a reference condition that may be regarded as perfect. In the cases of silicon and germanium, which find application in transistor electronics,&apos; the perfect structure is the diamond structure shown in Fig. I. In this structure, each atom is surrounded by four neighbors with which it forms four covalent or electron-pair bonds. These bonds use all of the four valence electrons possessed by each of the silicon or germanium atoms. The electronic structure of the crystal is thus complete and perfect. A crystal of silicon or germanium with a perfect electron-pair bond structure would be an insulator, In order for electrical conduction to occur, it is necessary for imperfections to arise in the electronic structure. In this lecture, I shall discuss four possible imperfections whose symbols and relationships are indicated in Table I. We shall consider first, as an example, a crystal of silicon containing an arsenic atom as an impurity.

Jan 1, 1953

By C. W. Phillips, D. N. Frey

A commercial Ti-Fe-Cr alloy, Ti-150, exhibits a martensitic transformation on cooling and two nucleation and growth reactions, one above and one below the Mg-Mf region, on isothermal holding below the single-phase ß temperature range. The reactions were followed by metallographic, X-ray diffraction, and microhardness methods. THE rapidly expanding engineering application of titanium and its alloys makes increasingly urgent an adequate knowledge of the effect of heat treatment on this material. The work herein reported is an attempt to determine certain aspects of the behavior of a commercially available alloy, Ti-150, during heat treatment. The alloy, with a nominal composition of 2.7 pct Cr, 1.3 pct Fe, 0.25 pct 0, 0.02 pct N, and 0.02 pct C, was received in the as-rolled condition as a 3/4 in. round. Slugs 0.11 to 0.12 in. thick were cut under a coolant using a silicon carbide wheel. Preliminary work established that the alloy consists of two phases, a (hexagonal close-packed) and /3 (body-centered cubic), at temperatures below 1750" to 1775"F, and of only /3 phase at higher temperatures. The slugs were heated for 1 hr in air at 1800°F to form a single-phase /3 matrix, then transferred to molten tin (1250° to 1650°F) or lead (1150°F and below) for isothermal holding. Holding temperatures ranged from 700° to 1650°F, times from 0.001 to 23 hr. The treated slugs were then sectioned, one part for metallographic examination and diamond pyramid hardness, the other, after deep etching to remove the high oxygen surface,&apos; for comparative lattice parameter determination and X-ray phase identification. Hardness measurements were taken on the lightly etched surfaces of the metallographic specimens; a 1000 g load on a 136° diamond pyramid was used. Five impressions on each sample were made and the average of the hardness calculated. The use of microhardness measurements to follow the course of an isothermal transformation reaction is undesirable because of the possibility of wide differences in microconstituent hardness.&apos; They were used in this case, however, because of the small amount of material available. At the higher transformation temperatures, where the above-mentioned objection was apparent, the readings were proportioned to correspond to the estimated ratio of transformed and untransformed constituents present. At lower temperatures, resulting in much finer microconstituents, the microhardness measurements were more uniform. The standard deviation of the mean of five impressions calculated from these latter values was 4.2 DPH. Employing 2a limits (probability 0.95) the experimental error of the hardness measurements averages was 8.4 DPH. The etchant used was composed of one part glyc-erol and one part 48 pct hydrofluoric acid." Of a number of etches tried, this one appeared most satisfactory. All micrographs were taken at 500X magnification and with oblique lighting to permit easier identification of the acicular structure resulting from rapid cooling. No advantage was gained by using polarized light for metallographic examination. Phase identification and lattice parameter measurements were made with a North American Philips high angle spectrometer in conjunction with a recording potentiometer. Considerable difficulty was encountered with some of the lattice parameter measurements because of the extreme broadness of the few diffraction lines obtained from samples consisting mainly of strained, untempered, quenched structures.

Jan 1, 1953

By J. B. Hess, C. S. Barrett

TO reach equilibrium between different phases in cobalt-rich alloys requires prohibitively long annealing cobalt-richalloystimes when temperatures are below about 700°C. The fact that a transformation from face-centered cubic to close-packed hexagonal readily tered takes place at temperatures below this in the cobalt-rich solid solutions is not an indication that thermally activated processes occur at an appreciable rate, for the transformation is well established as martensitic in nature. Wide divergence between heating and cooling experiments and high sensitivity to prior heat treatment make it difficult to judge temperatures of equilibrium between the phases.&apos; One object of the present work was to see if the information object of on the relative stability of phases could be gained by substituting plastic deformation for thermal agitation. Procedures were worked out that led to the determination of a diffusionless type of phase diagram, which represents the temperature of of phase equal stability for phases of the same composition, and the technique was applied to the Co-Ni system. Another object of the work was to see whether or not deformation would generate frequent stacking faults when these were thin lamellae of quentstackingfaultsa phase having higher free energy than the parent phase. The alloys were prepared in 80 to 100 g melts from cobalt (with metallic impurities estimated spectrochemically as follows: Ni, 0.05 pct; Fe, 0.001 pct.; Mg, Si, Cu, Cr, Al, < 0.001 pct) and Mond Car-bony1 nickel (with Fe, 0.05 pct; Si, 0.003 pct; C, 0.61 pct.; Cu, 0.001 pct; Co, Cr not detected, < 0.01 pct). The metals were melted in pure Al2O3 crucibles. An atmosphere of argon, that had been purified by passing over hot magnesium chips, was used for the alloys that, by analysis of the portions of the ingots actually used, were found to contain 15.3, 25.7, and 35.0 pct Ni, and vacuum melting (after degassing) was used for those containing 29.4 and 31.5 pct Ni. After induction melting the alloys were allowed to solidify in the crucible, and slices % in. thick x ½ in. in diam were annealed 12 hr at 1350°C for homogenization. These same specimens were used throughout the series of experiments, with annealing treatments of 4 hr at 900°C in purified hydrogen followed by furnace cooling, alternating with the deformation and X-ray tests discussed below. Results Spontaneous transformation was observed on cooling to room temperature in all alloys containing 29.4 pct Ni or less and by cooling the 31.5 pct alloy to — 195°C but was not observed in the 35 pct alloys after cooling to —195°C. These results are in satisfactory agreement with the cooling experiments of Masimoto.4 From these data it is clear that the temperature of beginning transformation M,,, drops to 20°C with the addition of about 30 pct Ni. The test for spontaneous transformation was metallographic. Specimens were thermally polished by annealing 10 hr in hydrogen at 1350°C, then furnace cooled; if trans- formation had occurred there were relief effects visible on the thermally polished surfaces. These markings were narrow straight lines, usually resolvable at high magnification as clusters of fine lines that resembled slip lines. It was concluded that they resulted from displacements on (111) planes, for the number of directions in individual grains often reached but never exceeded four, and lines could always be found parallel to the thermally etched (111) boundaries of annealing twins. The markings were thus consistent with the idea that the transformation occurs by (111) plane displacements (Shockley partial dislocations moving on (111) planes). This was further confirmed by X-ray tests for stacking disorders. Using an oscillating crystal technique previously employed to detect strain-induced faulting in Cu-Si alloys," streaks indicative of the stacking faults were looked for and found on X-ray films of the spontaneously transformed 25.7 pct Ni alloys, as expected by analogy with Edwards and Lipson&apos;s results on pure cobalt." The streaks were much intensified after rolling at room temperature. Transformation induced by plastic strain was investigated as a function of alloy composition and temperature of deformation. A series of tests was made to determine suitable straining and X-raying techniques. Filing was found inferior to abrasion in converting cubic samples to hexagonal, and abrasion was less effective than peening in producing smooth unspotty Debye rings in the X-ray patterns. Because the diffraction lines were broad, Geiger-counter spectrometer records of filings were less sensitive in revealing small amounts of transformed material than X-ray patterns recorded on films in a small diameter camera. After these exploratory tests the following methods were adopted. Specimens that had been annealed at least 4 hr at 900°C and furnace cooled were mounted in a block of aluminum, brought to temperature, and peened thoroughly with a mullite pestle preheated to the same temperature. The specimens were then quenched to room temperature. In peening, a circular area of % in. diam was given 500 blows. A few control tests showed that an additional 1000 blows did not detectably change the proportions of the phases present. The amount of transformation was judged by X-ray reflection patterns from the peened surface, using the innermost four lines of the cubic and the hexagonal patterns with filtered CoKa radiation,

Jan 1, 1953

By E. S. Bumps

A series of macrographs are presented for the purpose of graphically recording the strain phenomenon that accompanies the energy transition in the Charpy impact testing of a mild steel that is susceptible to strain aging. STRAIN patterns in mild steel Charpy impact specimens were obtained in order to determine whether, on the first appearance of plastic strain during deformation, the initial fracture cracks appear in the region of plastic strain or in the elasti-cally deformed regions between. Although this attempt to locate the initiation of cleavage was not successful, the observed strain patterns illustrating various stress conditions in partially deformed Charpy specimens are presented along with a discussion of the possible dependence of transition energy on the yield phenomenon. Earlier work on the development of strain patterns in mild steel have been reported by Fry1 and later by Jevon.2 Harris, Rinebolt, and Raring3 observed characteristic strain markings on the surface of Charpy V-notch impact specimens fractured above and below the transition temperature which they presented schematically. It is intended that the strain figures presented here will add to the literature a graphic correlation of strain with transition energy in impact specimens. Samples of % in. round hot rolled, 0.20 pct C steel were machined to standard 0.394 in. sq, V-notch Charpy impact specimens. Preliminary testing involved determination of transition temperature, Fig. 1, using a Sontagg impact tester. These data were subsequently used to select temperatures above, within, and below the transition range at which specimens were partially deformed. Partial deformation was obtained by either varying the energy or the testing temperature, see Table I. Macroscopic strain figures shown in Figs. 2 to 19 were produced by several metallographic repolish-ing and etching steps. The macroetchant used was as follows:4 120 g HCl, concentrated; 100 ml water; and 90 g cupric chloride. Strain figures were obtained on the outer surface and on sections through the central portion of the impact specimens in order to determine an approximation of the volumetric strain pattern. In the tensile strain figures reported by Jevon, it was found that strain etching would not work immediately following strain unless the material was heated to 200°C. The impact strain patterns presented here were obtained without this heating, but the specimens were not etched until ten months after straining. This confirms a discussion of Jevon&apos;s paper, in which it was pointed out that strain figures can also be developed after aging for long periods of time at room temperature. Hardness of the strained and unstrained portions, revealed by the etched pattern, was explored using R, impressions converted to R, hardness values. Discussion of Results In the impact test, as in the tensile test, some parts of the specimen yield and deform plastically, while other regions are deformed only elastically. The plastic deformation bears a relation to the imposed stress pattern. In the strain figures presented here, the plastically deformed regions are the dark etching ones. The strain figures are always symmetrical because the stress state in the Charpy-type specimen under impact loading is symmetrical. The difficulties encountered to produce initial cracks are intimated in Figs. 2 and 4. At a temperature of —75ºF, the stress was not sufficient to pro-

Jan 1, 1953

By W. G. Bearden, P. P. Scott, G. C. Howard

This paper concerns the rupture or breakdown of rock formations as related to drilling, completing, and stimulating production of wells, and comprises data compiled from a study of literature and records of treatment of oil and gas wells. and from tests conducted in bores drilled into rock cores and outcrops of rock. Results of the investigation indicate that the internal pressure to rupture cylinders of rock and to breakdown rock formations surrounding a bore in the earth is dependent upon the extent of intrusion of fluids. the position of bedding planes. the ratio of internal to external diameter, the tensile strength of rock, and magnitude of confining pressure, and is independent of the size of bore, degree of fluid saturation. and temperature of rock within practical limits. It is concluded that the mathematical relationship of pressure in bores and stresses in the surrounding rock must not be limited by the simplifying assumptions of homogeneity. isotropy, and impermeability; that the incidence of lost circulation of drilling fluids to induced fractures may be reduced by preventing intrusion of fluids into the small intrinsic fractures along weak bedding planes; and that the magnitude of the breakdown pressure of wells to be treated may be lowered by removal of mud cake. INTRODUCTION The purpose of this paper is to present and discuss the results of tests which may serve to broaden the understanding of the phenomena of rupture or breakdown of rock and thus contribute to the improvement of the techniques for drilling and completing wells. including such operations as preventing lost circulation, stimulating production, and placing cement. Since the early recognition of the possibility of rupturing rock adjacent to a well by fluid pressure, the distribution and magnitude of stresses around a well and the internal pressure to cause failure have been expressed mathematically by application of the principles defining the elastic and inelastic behavior of thick-walled cylinders of a homogeneous. isotropic, impermeable material. In either the elastic or plastic state, if the conditions of homogeneity. isotropy, and impermeability were the normal characteristics of rock. there would be no reason to question the validity of the above principles when applied to rock. However. since most rock formations are characteristically permeable to some degree, contain bedding planes and small intrinsic fractures. and are heterogeneous, rendering invalid the assumptions of homogeneity, isotropy, and impermeability, the application of the thick-walled cylinder theories to the behavior of rock formations penetrated by a bore appears illogical. Also the failure to consider the effect of the properties of the drilling fluids, which certainly intrude in various degrees into most rock formations. is further cause for questioning the application of these principles. Even in the case of cylinders of hardened chrome-nickel steel, which would he considered relatively homogeneous isotropic. and impermeable, as compared to rock, it has been observed that the internal pressure capable of being withstood by the cylinders varied with the sizes of molecules comprising the rupturing fluid used. Because of these apparent weaknesses in the theories of the behavior of thick-walled cylinders when applied to bores in rock, and the importance of knowing the true behavior of rock under the influence of fluid pressure when planning drilling and completing procedures for wells, tests were undertaken to determine by observation the actual rupturing pressure of cylinders of rock and the effects of such variables as environmental conditions and characteristics of rock formations, fluid properties, and bore dimensions. It was intended that by these tests the validity of the thick-walled cylinder theories when applied to rock would be determined and, if found invalid, mathematical expressions would be derived for predicting stress and rupturing pressure of rock formations under various conditions. Since the derivation of mathematical expressions has been only partially completed, all of the results of the latter phase are not included in this paper. PROCEDURE The investigation was initialed with a study of the theories pertaining to the rupturing of thick-walled cylinders of homogeneous. isotropic, impermeable material and a study of the

Jan 1, 1953

By H. F. Bishop, F. A. Brandt, W. S. Pellini

The solidification mechanism of experimental steel ingots (7x7x20 in.) was studied by thermal analysis. It was determined that solidification proceeds in wave-like fashion at rates which are determined by the carbon level, superheat, and mold thickness. The thermal cycles of the mold walls were related to the course of solidification. ESPITE marked advances in the field of solid state transformation, metallurgical research has contributed comparatively little exact quantitative data on the mechanism of solidification of metals. There is, therefore, a great need for such data in the various metallurgical industries. The mechanics of solidification of ingots have been investigated in the past primarily by studies of the rate of skin formation as indicated by bleeding or "pour out" tests. The "pour out" method, however, is a tool which gives only approximate information. In the case of alloys with wide solidification ranges, such as irons and certain nonferrous alloys, the method will not work at all; in the case of alloys of intermediate solidification ranges, such as commercial steels, the information may be misleading. Thus, the general adoption of this method has resulted in divergent conclusions regarding the solidification process. Chipman and Fondersmith1 by means of bleeding tests have shown that the linear growth of a solidifying ingot wall follows a parabola of the general form, D = K C, with the start of solidification delayed until superheat is exhausted, as indicated by the constant C. These tests were carried only to a wall thickness of about 5 in. using an ingot of approximately 17x39 in. in cross-section; hence the latter stages of solidification were not studied. Matuschka2-3 indicated that linear solidification of ingots is rapid at first, then slow, but toward the end of solidification the rate becomes extremely rapid again. Spretnak&apos;s4 bleeding studies indicated that, wall growth is expressed more rigorously by two parabolas, and that their point of intersection corresponds to a change of solidification mode from columnar to equiaxed. Spretnak also showed that the K values of the first parabola are always the same regardless of superheat. Nelson bled ingots of square cross-section and found that linear wall growth is initially rapid but decreases continually until the end of solidification. He also concluded that rate of solidification in ingots of square cross-section increases 2.15 pct for every 10 pct increase in cross-sectional area of the mold. The mold ratios considered (ratio of cross-sectional area of the mold to cross-sectional area of the ingot) were all less than 2 to 1. The subject of solidification has also been treated mathematically in many cases, but because of the lack of accurate thermal constants and the simplifying assumptions required, as their authors generally acknowledge, they represent only approaches to the actual conditions of ingot solidification. A third method of studying solidification is the electrical analogue method promulgated by Pasch-kis6-7 and by Jackson and coworkers.8 This method treats solidification as a heat transfer problem with the solidification cycle synthesized on an electrical circuit. Paschkis in his treatment of solidification considered the fact, which was generally ignored, that solidification of steel is not simply the growth of a plane solid wall but a more complex process occurring over a temperature range as indicated by the constitution diagram. Undoubtedly, the anomalous results obtained by bleeding tests arise from the inability to measure quantitatively this mushy condition. The shape of Paschkis&apos; solidification curves are more nearly in accord with those of Matuschka, in that they indicate rapid linear solidification at the beginning and end of solidification with intermediate solidification occurring at a slower rate. Paschkis indicates a definite lengthening of solidification time with increasing superheat. Thermal analysis is a direct method providing exact information for all types of metals regardless of solidification range and was thus adopted in the present program to follow the entire course of solidification from the surface to the centerline of the ingots. The method has the added advantage of being adaptable to following the thermal cycle of the ingot mold during the course of solidification. Test Methods The ingots studied were of square cross-section, 20 in. long, tapered from 71/4 in. at the top to 63/4 in. at the bottom, and fed with a hot top 7 in. in diam and 12 in. high. The molds were uniform in wall

Jan 1, 1953

By W. Rostoker

A STUDY of the titanium-oxygen system&apos; involved an associated series of measurements of the lattice parameters of the a and TiO phases. The results permit some interesting deductions which are herein reported. A comprehensive survey of the physical PI-operties of the phases in this alloy system has been made by Ehrlich.2 However, only impure titanium was available at that time, so that some revision of his measurements is to be expected. The lattice parameters were calculated from the high angle lines of Debye-Scherrer patterns taken in a 14 cm camera and using filtered CuKa radiation. The specimens were prepared largely by crushing and screening of lump samples which had been quenched from elevated temperatures. Only in the case of low oxygen contents was it necessary to resort to filing and annealing. The results of the lattice parameter studies are graphically presented in Figs. 1 and 2. It will be seen that oxygen produces a pronounced distortion of the c parameter of the a phase (hexagonal close-packed). The trend is in general agreement with Ehrlich&apos;s work, although the divergence of actual parameter values strongly suggests that his titanium was very impure. It will be noted that the a phase of titanium can tolerate the unusually high saturation solubility of about 34 atomic pct 0. By virtue of this unique effect, it is possible to make a calculation of the effective atomic diameter of oxygen when dissolved in a lattice with metallic bonding. This has not been possible before. Ehrlich&apos;s2 density measurements demonstrated that oxygen occupies interstitial positions in the a lattice and the trend of the lattice parameters would certainly support this. In a hexagonal close-packed unit cell the largest interstitial positions lie at (2/3, 1/3, 1/4) and (2/3, 1/3, 3/4). Accordingly, if both of these positions were occupied, the ratio of titanium to oxygen would be 1:1. The extrapolated c parameter may be taken as between 4.93 and 4.99?. The a parameter appears to reach a constant value of 2.955? at low oxygen contents. The distance of the center of a titanium atom site from the [vc2/16+a2/3-1.448] Then the atomic diameter of the oxygen atom is represented by the function: where the radius of the titanium atom is 1.448A,

Jan 1, 1953

By Ralph W. Edie

"IntroductionTHIS PAPER presents some analyses of diabases from a number of metallogenic provinces in Canada and the United States. It is intended as a contribution to the literature on the genesis of mineral deposits associated with diabase.As it has been in the past, opinion today on the origin of the cobaltnickel- native silver and associated pitchblende type of deposit is sharply divided. Some geologists hold that this type of deposit is in some way genetically related to intrusive diabase; others are of the opinion that the deposits are related to granite. The controversy, like others of a similar nature, probably will not be settled satisfactorily for many years to come, •but in the meantime it is recognized that, with respect to most deposits of the type referred to, altogether too few facts are known for accurate conclusions on genesis to be drawn. To contribute in a small way to factual data on this whole .problem, the writer analyzed diabase from several districts in Canada in which deposits of the aforementioned type occur. For comparative purposes, the copper, cobalt, and nickel content of diabase from Cornwall, Pennsylvania, and of norite from the Sudbury basin of Ontario, was also determined.Insofar as is known, none of the analytical work undertaken had been previously carried out."

Jan 1, 1953

By R. S. Archer

THE name molybdena was employed by Pliny to denote various substances resembling lead. Later this name was applied to galena-the naturally occurring sulfide of lead-or substances of similar appearance. By the middle of the eighteenth century, it was applied to graphite and to the mineral sulfide of molybdenum (MoS2) now called molybdenite. This confusion is quite understand- able inasmuch as these substances look and feel very much alike. In 1778, the Swedish chemist Scheele published a treatise in which he pointed out essential differences between graphite and molybdenite. On treatment with nitric acid, molybdenite, unlike graphite, produced a peculiar white earth with acidic properties which he called molybdic acid. Since the same mineral gave off sulfurous fumes on heating, he concluded that it was a sulfide of molybdenum. In 1790, there appeared an account of the isolation by P. J. Hjelm of the new element molybdenum, as a metallic powder, by heating the oxide with carbon. It was not until Bertelius conducted the necessary experiments, about 1818 to 1825, that the foundation of the chemistry of molybdenum was laid. The only recorded use of molybdenum during the first century after its isolation was as a chemical reagent, primarily for the determination of phosphorus. It was not until the last decade of the nineteenth century that the use of molybdenum in steel appears to have been investigated. A

Jan 1, 1953

By C. G. Dunn, M. Sharp

HE orientations of 137 crystals of copper pro-T duced by secondary recrystallization in a cube texture matrix have recently been obtained. Although the crystals were not prepared for the purpose of determining a secondary recrystallization texture, the orientations obtained proved to be rather interesting, as they confirmed, in part, published results and also disclosed additional preferred orientations in the texture. The investigation of Dahl and Pawlek,&apos; Bowles and Boas,&apos; and Kronberg and Wilson3 showed respectively that the orientations of secondary grains growing in a cube texture matrix were related to those of the primary grains by a rotation of approximately 30" about [001], the rolling direction, by 30" about a <111> direction, and by either 22" or 38" about a <111> direction. Kronberg and Wilson also obtained a component of the texture similar to that of Dahl and Pawlek except the angle of rotation about [001] was 19". When the cube texture matrix was deformed a small amount, Kronberg and Wilson also obtained large grains on subsequent annealing corresponding to a rotation of 15" about the normal to the sheet, but these grains should not be classified as secondary recrystallization grains since they were produced subsequent to mechanical straining. The particular texture obtained, of course, depends on the composition of the copper and the processing schedule employed, since these factors markedly affect the primary recrystallization texture and the sharpness of any cube texture produced. In the present investigation, pieces of OFHC copper in the form of M in. round bars were cold forged to a thickness of about 0.40 in., annealed 1 hr at 350°C in an atmosphere of hydrogen, and cold rolled crosswise to a thickness of 0.200 in. These pieces were given a penultimate anneal of 1 hr at 350°C in hydrogen and a 90 pct cold-rolling reduction lengthwise to a thickness of 0.020 in. Indentations generally were put in one end of the as-cold-rolled strips to promote earlier formation of secondary grains.

Jan 1, 1953