Search Documents

The silver-lead ores of Yerranderie occur in a series of narrow, flat-dipping lodes in small bodies of quartz porphyry, intrusive into Upper Devonian volcanics, which are exposed in the western flank of the Permo-Triassic Basin of central New South Wales, about 80 miles south-west of Sydney (Harper, 1930; Lawrence, 1953). The lodes strike about E.-W. and are from 1,200ft. to 2,000ft. long. They consist of a series of ore shoots from 3ft. to 100ft. long, and up to 5ft. thick, though commonly under 2ft. thick, interspaced with low grade sections. They dip at from 18°S. to 400 S., and have persisted down the dip for 1,450ft. (693ft. vertical depth) in the Wollondilly mine, for 1,120ft. in the Bartlett's mine, and for 850ft. in the Wonga mine.The grade of ore in the Bartlett's mine was from 32% to 40% lead, from 100 oz. to 130 oz. silver per ton, 0.5 to 4.0% arsenic, with ore ,as rich as 20% arsenic on the No. 6 and No. 7 levels of the Silver Peak mine, the underlay extension of the Bartlett's lode, about 1% copper, and up to 4 dwt. gold per ton. In the Wollondilly mine the average grade was 15% lead, with sections as rich" as 36% lead, from 75 to 165 oz. silver per ton, 0.6 to 3.3% arsenic, 0.2 to 0.7% antimony, 0.8% copper, and up to 7...5. Cl~t. gold per ton. The zinc content of the ores is slight, and has not been recorded.Mining began about 1898, and to date more than 110,000 tons of ore, valued at £1,800,000, has been raised. Large scale mining ceased about 1935. The chief mines operating were the Bartlett's mine (formerly Colon Peak), the Silver Peaks, which is the underlay extension of the Bartlett's, the Wollondilly (or Yerranderie) mine, and the Wonga' (or Tonalli) mine.

Jan 1, 1953

By C. W. Owings

The Bureau of Mines has conducted a survey to determine potential exposure of mine workers to dust produced in connection with intermittent rock drilling in coal mines. Eighteen mines in 3 states were visited, and 30 different operations were observed, as follows: 10 drilling in draw slate, 8 drilling top rock for brushing or grading, 2 drilling in the coal face, 4 drilling in the bottom, 2 drilling top rock for overcasts, 2 drilling in faults or boulders, 1 drilling for roof bolting, and 1 drilling for trolley hangers. Dust respirators were worn by drilling crews during 16 of the 30 operations. Three hundred thirty-two samples of air-borne dust were collected during the survey. ACKNOWLEDGMENTS The information in this report is based on samples collected and observations made in bituminous-coal mines. Operating officials at these mines have contributed to this study, and their cooperation is gratefully acknowledged. All samples were counted by Thomas B. Kirby, chemist, and Dominick A. Ambrosia, scientific aid, and were analyzed by Gretta S. Baur, physicist, and Patricia M. Gussey, scientific aid, of the Health Branch of the Bureau of Mines.

Jan 1, 1953

By Howard N. Hall

The compressibility of reservoir rock is a factor which is generally neglected in reservoir engineering calculations. This is due in part to the fact that there is little published information on rock compressibility values for limestones and sandstones. Omission of rock compressibility is undoubtedly justified in calculations for saturated reservoirs; however, in under-saturated reservoirs,* expansion of the rock accompanying decline in the reservoir pressure may be of such magnitude as to affect materially the prediction of reservoir performance. The effect of rock compressibility will be of most importance in: (1) calculation of oil in place by pressure decline data in undersaturated volumetric reservoirs when the limits of the field are unknown or indefinite, and (2) studies of natural water drive performance. To estimate its importance in such cases, a series of laboratory tests were made to obtain usable values for reservoir rock compressibility. The total, or effective, compressibility of any reservoir rock is a result of two separate factors, namely, expansion of the individual rock grains, as the surrounding fluid pressure de-

Jan 1, 1953

By W. H. Triplett

DISCUSSION John G. Barry (Mexico)—"The Nerinea limestone," writes W. H. Triplett, p. 584, "is ... medium-bedded (0.5 to 1.0 m)...." This is the Zuloaga formation. It has always been described as thick-bedded (1.0 to 3.0 m). "Whether the marls and shales were less amenable to replacement," he goes on to say, ". . . is a matter of opinion." In general, it is probable that the thinner-bedded formations were less competent than the nearby thicker-bedded, so that the latter produced pre-mineral breccias when all were subjected to flexing stresses. With reference to Mr. Triplett's analysis, p. 584, under Lower Cretaceous, in the Taraises and Cupido formations some few horizons should be considered as possibly containing hidden orebodies. In the Potrero camp, shown on the general map in the northwestern part of Fig. 4, p. 587, several mineralized beds are known; they are found throughout the whole thickness of the Cuesta del Cura formation. With regard to intrusive rocks, p. 585, the general map, Fig. 4, shows that the Potrero and Noche Buena camps are near a third, monzonitic intrusive. It seems doubtful that the Aranzazu was any hotter than the Providencia camp. However, the former does contain large deposits of exogenetic silicates, which in large part occur within the Zuloaga limestone, as shown by Bergeats in a stereogram. At the Aranzazti camp the La Caja formation was only slightly changed, whereas it was altered highly at the Providencia, possibly en-dogenetically. That the temperatures at the Providencia camp were relatively high at one time is also shown by the tourmaline veinlets and lenses in the monzonite and by the garnets on Temeroso peak; high temperature mineralization has possibly been eroded. Maps and sections show that the Concepcion del Oro —Temeroso stock occupies the original locus of some 40 kms of sedimentary rocks. The remains of large roof pendants at Carmen and Animas indicate that stoping was active. Whether all the sedimentaries were stoped and assimilated presents a lively problem, a correlative of which would be an estimate of the original constitution of the invading instrusive rock. As to extrusive rocks, see p. 585, there is also a large thick area of the extrusives left near Noche Buena in the "La Caja" intramontane valley of the La Caja range. This place gave its name to the range. The volcanics are also said to occur in considerable amount in the Mazapil valley.'' Turning now to the remarks under Regional Structure, p. 586, as partly indicated on the general map, Fig. 4, the Mazapil Mountains of the Mazapil region are a continuous, U-shaped range including a northern leg of some 24 km, a southern leg of similar length, and a uniting base which lies to the East and which measures some 10 km in a S 20 E direction. Thus the U-shaped mountains are continuous through a length of 58 km and also contain one continuous anticline, the adjacent valleys being synclinal. The northern leg of the U is called the La Caja range, the base is called the Concepcion del Oro range, and the southern leg the Santa Rosa range. The ranges in northeastern Zacatecas and southern Coahuila contain anticlines and the valleys contain synclines, which where thin are necessarily highly compressed isoclines with very steep dips. Many of the anticlines also have isoclinal components which are overturned, original mushroom tops being indicated. The anticline in the base of the U of the Mazapil Region, Concepcion del Oro range, is a recumbent anticline, over to the ENE, with a necessarily subjacent recumbent syncline.

Jan 1, 1953

By J. H. Hamilton, J. R. Lewis, K. W. Heinlein, V. D. Hanson, J. M. 194-000-000-006 Vonfeld, J. P. Denny

TWO overfeed drum-type separators using a suspension of magnetite in water as the separating medium have been installed in the Champion NO. 1 preparation plant of the Pittsburgh Coal Co., Division of the Pittsburgh Consolidation Coal Company. A simplified flow diagram of the Champion No. 1 coarse coal circuit is shown in Fig. 1. A railroad car rotary dump, capable of handling 20 cars per hr, discharges the coal into a hopper. Coal is fed from the hopper of the rotary dump to a 60-in. belt conveyor by two reciprocating pan-type feeders. The belt conveyor feeds the run of mine coal onto the main raw coal screen. The first deck is fitted with 3 in. round hole perforated plate which removes the 3x0-in. coal. The second deck of the screen is equipped with 6-in. lip screens which separate the remaining coal into +6 in. and 6x3 in. The +6 in. coal is transferred to a shaking picking table and then discharged onto the loading boom. The 6x3-in. coal is fed to the No. 2 dense medium vessel for cleaning. The clean coal from this unit flows to a vibrating screen where the medium is removed and the coal sized into 6x4 in. and 4x3 in. The 6x4-in. coal is transferred to the loading booms and the 4x3-in. is conveyed to the clean coal classifying screens to remove degradation. The 3x0-in. raw coal is blended in a system composed of three storage bins having a total capacity of 400 tons. From these bins the coal is fed onto a 48-in. flight conveyor by three reciprocating feeders. This flight conveyor delivers the coal to the Rheo plant. The 3x0-in. coal is then cleaned in two 48-in. Rheolaveur launders each equipped with two Rheo boxes. The first set of boxes removes a primary refuse and the second set produces a middling product which is recirculated in the launders. The cleaned coal and water overflows from the primary launders to two sizing and dewatering shaker screens where the water and — -in. coal are removed for further cleaning in the Rheo fine coal plant. The 3x3h-in. clean coal is combined with the 4x3-in. coal from the No. 2 vessel, sized into 4x2 in., 2x1 34 in., and 1'/4x in., then sent to the loading booms. The 3x0-in. refuse from the primary launders is normally fed to the No. 1 dense medium circuit, but any portion or all of this material can, as an alternate, be processed in the Rheo rewash launder. The primary refuse when fed to the dense medium circuit is screened into YSXO which is cleaned in the fine coal plant and 3x for cleaning in the No. 1 vessel. The clean coal from this vessel is passed over a vibrating drainage and rinse screen, then sluiced to the rewash sizing shaker where it is dewatered and sized for loading. The installation of a pilot plant separating vessel using a suspension of magnetite in water was pro-

Jan 1, 1953

By N. Van Wingen, Norris Johnston

Laboratory flood pot testing of California sands has progressed to a considerable extent in the past 18 months. Flood evaluations have been carried out on over 200 large core samples. Many of these were heavy oil sands of high permeability and completely unconsolidated in nature. The oil frequently formed a bank, though some of the oil was recovered in the subordinate phase of the flood, by viscous drag. Flood pot recoveries as high as 1400 bbl/acre ft have been recorded. Reservoir analysis suggests a conformance factor of 0.4 to reduce laboratory recovery to probable field practice. Oils with viscosities up to 1800 cp have been successfully handled in flood pot evaluations. The shallow, loose sands are not well adapted to the application of- high pressures to offset the high viscosities. INTRODUCTION Secondary recovery may be said to have started 60 years ago when accidental floods occurred in the Bradford sand in Pennsylvania. About 1921 artificially conducted water drives came into extensive use and since that time the great Bradford field has been almost completely subjected to water flooding. During the last 30 years, most of the known medium and deeper production in California has been discovered and is being exploited by primary recovery methods supplemented in some instances by high pressure gas injection. The California area is just beginning to feel the need for secondary recovery in view of an unprecedented market demand and the rapidly rising cost of new pool discoveries. With the presently recognized desirability of secondary recovery in California, there must also be appreciated a number of serious differences between the water flooding problems here as compared to the territory east of the Rockies. California sands are generally thicker, and are frequently soft and argillaceous. The oils are often heavier and asphaltic. Much of the oil is below 15°API, occurs at shallow depth, is cool and free from appreciable dissolved gas, which results in relatively high reservoir oil viscosity. Secondary recovery is particularly beneficial where primary recovery has been poor and where no natural water drive exists. These conditions apply particularly to the heavy, shallow, clean production from soft, often argillaceous California sands so abundantly found at depths less than 1500 feet. Often, too, there is a totally insufficient supply of water of satisfactory quality to inject at a reasonable cost. Also, the crude oils are priced far below the premium Bradford crude. Although these and a number of minor problems beset the operator desirous of starting secondary recovery, great progress has been made in the past few years in finding how to adapt previous Mid-Continent and Eastern experience to water flooding in California. There are about nine projects for subsurface injection of water which can be said to classify as secondary recovery operations. Subsurface water disposal would so classify when the sand receiving the water is a nearby oil producer, as is often the case. When water is injected subsurface into a barren sand, the operation does not classify as secondary recovery. Several of the most active operators avail themselves extensively of preliminary engineering and laboratory work to guide their decisions, while others enter small scale flooding operations directly in the field. It is the laboratory work pertinent to several of the California secondary recovery projects that this paper discusses. PURPOSES OF LABORATORY FLOODING TESTS Experience in areas where water flood operations have been carried out has indicated that careful engineering planning is an important requisite for subsequent economically successful field operation. Floods that fail are more frequently those where operations were instigated without a prior engineering investigation to determine the effectiveness of the injection fluid as an oil displacing medium. Laboratory data are essential in the evaluation of an oil property for secondary recovery possibilities. Success or failure of secondary operations can under certain special circumstances be determined directly by cores and their subsequent routine analysis. This is particularly the case where flushing of the cores in the course of coring is negligible and where the results of the analysis can be compared with existing secondary recovery operations. Where these conditions cannot be' fulfilled, the application of core analysis is more limited. In such event, the results obtained by water flooding core samples in the laboratory have been found to be of prime importance. Cores may be flooded "raw" as taken from the well or in the event flushing and depletion of the cores in the process of drilling are major factors the fluid content may be artificially restored prior to the flooding. Laboratory studies should also be made to determine the suitability of the water selected for injection. Thus interaction between injected and formation water may cause precipitates to be formed which may plug the sand. Even more important, especially to California operations, is the possibility of the hydration of formation clays by the injection water. The aims of flood pot and associated tests are basically to determine the residual oil saturation after flood, the water-oil throughput ratio and to establish whether an oil bank is formed. Additional information which can be obtained from flood pot tests pertains to the pressure differential required to effect displacement, the relative permeability to oil in the oil bank and the relative permeability to water in the watered out region behind the bank.

Jan 1, 1953

By M. Semchyshen, G. A. Timmons

P. A. Beck (University of Illinois, Urbana, 111.)—An interesting result of this work is the fact that in cold rolled molybdenum sheet complete loss of work hardening is obtainable on annealing, without change in texture. The retainment of the cross-rolling texture on soft-annealing is particularly significant, since this is essentially a single orientation texture, where texture retainment could be achieved by only one of the two niechanisms which produce this effect in aluminum,16 namely by recrystallization in situ. Recrystallization in situ was originally discovered by Collins and Mathewson (1940) and by Crussard (1944) as a phenomenon taking place on annealing in relatively mildly deformed single crystals of aluminum. It now appears to be a major (in many cases the major) mechanism of annealing of severely cold rolled poly-crystalline material, not only in aluminum,le but in metals as different in character as beryllium," tita- nium,'" and molybdenum. All these data now confirm the general validity, at least for more or less pure metals, of the interpretation of the annealing process given a few years ago by Smith.'" The whole question of recrystallization is now reopened. Indeed, it appears that recrystallization, as defined traditionally, may not occur at all, since at the time "deformed material" is absorbed by "recrystallized grains," it has already become completely strain free by recovery and "recrystallization in situ."

Jan 1, 1953

By John A. Legge Jr.

"ACCOMPANYING Alberta's great natural endowments of oil, wheat, scenery, fishing, and hunting is also a generous endowment of geophysical problems to plague the interpreting geophysicist. These problems — by no means unique to Alberta — are sufficiently numerous and outstanding to be of major concern in exploration. Some of them have been adequately solved, others are well on their way to being solved, and still others remain almost completely unsolved. Often a problem readily solvable in one area can be solved only with great difficulty in another. Many are closely allied with the geological conditions and require the best co¬ordinated efforts of the geologist and geophysicist for their solution.It is a fairly general practice to study rather carefully the geophysical characteristics of known producing reefs in order to obtain data on which to base an interpretation of unproven areas. This practice obviously has a very sound basis, for, as discoveries become more and more widespread in the Alberta basin, it is found that the variation' in geological conditions has a marked effect on the seismic results, as would be expected. By carrying this analysis over an area it is possible more and more to anticipate the geophysical picture which should be obtained in connection with reefing under the varying geological conditions. Another phase of this procedure, and one that has received less attention, though it is certainly of importance, is the analysis of the all too numerous failures. A study of these failures may be more fruitful than a study of the successes for it may indicate weaknesses of field procedure, computations, or in¬terpretation not particularly obvious in the discovery areas. These studies must not only include the geophysical characteristics of the observed `anomalies', but should also be coupled with a thorough geological study to ascertain whether some unanticipated geological condition is responsible for the erroneous geophysical interpretation."

Jan 1, 1953

By Elmer Weber, W. M. Baldwin

Solid lead obeys a single parabolic weight increase vs. time law. In contrast, liquid lead undergoes three successive parabolic weight increases vs. time laws, the first of which has a low constant relative to the latter two. The conversion times for the change from one parabola to the next decrease with increasing temperature. IN recent reports on the subject,1,2 it was noted that zirconium and titanium scale in air by a complex mechanism. The scale first forming on the metal is protective to the extent that it gives a low constant, K, for Tammann's, and Pilling and Bedworth's parabolic equation: w² = Kt [1] relating weight increase, w, due to chemical reaction of the metal with the air, and time, t. After hundreds of hours of apparent stability in some cases the first scale yields to another that offers little protection to the metal. This transition from one scale to another, from a slow parabolic oxidation reaction to a fast one, was not due to impurities in the atmosphere or incidental effects (changing environment, etc.) but was a specific behavior of the metal itself, the transition occurring at definite times (dependent on temperature) and showing other reproducible traits. In view of this behavior how can long-time service behavior be predicted from short-time laboratory tests, not only in the case of these metals, but in any case? Certainly a systematic study of the type of scaling behavior described above—wherever it is found—would help to answer this question. The present paper is a report on the behavior as it is found in lead—the only metal to the authors' knowledge for which the behavior has been described at all, if inadequately, for our present purpose.* At least four oxides of lead are known, of which one occurs in two allotropic forms. They are ß (red) tetragonal PbO stable up to 486°C;8 a (yellow) orthorhombic PbO stable from 486°C up to its dissociation temperature in air at about 2300°C;9 minium or Pb3O4 which from the dissociation pressure data given in Fig. 1 decomposes to PbO at 540°C in air; lead sesquioxide or Pb2O3,; and lead dioxide or PbO2 which, according to Fig. 1, decomposes in air at 400°C to minium. In view of the high dissociation temperature of PbO, lead will scale up to at least its boiling point. Further, it is known that oxygen is almost insoluble in liquid lead.'V his implies a fair probability that an oxide scale would not dissolve in the molten metal and would afford the same protection to lead in the liquid state as in the solid. All of the oxides of lead for which specific gravity data are available are more voluminous than an equivalent weight of metal or a lower oxide from which they might form, hence the scales will be in compression. Lead oxides are known to be ductile, so it would be anticipated that they would form coherent nonporous scales. It is not surprising to learn, then, that both solid and liquid lead scale according to the Tammann, and Pilling and Bed-worth law.14,15 (Gruhl states that at 600°C and above lead oxidizes linearly with time because of "spitting" of the scale.) The parabolic constants K reported by various investigators3,14-16 are badly scattered, however, as shown in Fig. 2. The oxides formed on solid lead were described as being reddish-brown but were not chemically identified by Pilling and Bedworth.15 Gruhl's descripdin³ of the appearance of the scales On his liquid samples indicates that a (yellow orthorhombic) PbO is formed initially on the specimens but gives Way eventually—at least at temperatures below 486 °C— to .ß (red tetraunal) PbO, and that below 540°C minium—Pb3O4 :is firmed at an even later time as an overlay on either the red or yellow PbO. Fig. 3 is a graphical interpretation of Gruhl's description. Gruhl does not indicate any change in the parabolic scaling rate as yellow PbO converts to red. He does indicate that minium reduces the scaling rate, al-

Jan 1, 1953

By Joseph J. Wallace

1. From the standpoint of known recoverable reserves, the following is the order of importance of the beds: Upper Kittaoning, Lower Kittanning, Upper Freeport, Lower Freeport, Middle Kittaning, Clarion, Pittsburgh, and Redstone. 2. mown measured and indicated reserves in all beds, based on a minimum thickness of 14 inches and on 1,800 tons per acre-foot of coal in place, me estimated at 1,859 million short tons as of January 1, 1952. Of this, 1,351 million short tons me in beds 28 inches and more thick. Areas in each bed were omitted from the estimates because available data relative to the bed characteristics are too meager to make an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.

Jan 1, 1953

By J. B. Wagstaff, R. A. Buchanan, J. F. Elliott

High speed photography through blast-furnace tuyeres showed coke particles moving rapidly. Model studies showed a raceway was formed and gave quantitative results which were correlated with actual blast furnaces. Another study showed the similarity between hanging and the flooding of a packed column. This was explored by models. THE combustion zone before the tuyere in an iron blast furnace is a vital region because here are generated: 1—most of the gases on which the furnace depends to carry out its basic operation of reducing iron ore to the metallic state, and 2—the major fraction of the heat required in the nearby regions of the furnace for the various reduction reactions, the fusion of the slag, and the melting of the iron. Since the greater part of the coke is consumed in this region, the descent of the burden must be greatly affected by the characteristics of the tuyere zone. This region then would seem to be a profitable field for study. Fortunately, a view into this important zone is available to the operator through the tuyere peep sight. Here he sees relatively dark pieces of coke "dancing" in the blast. What he sees is of considerable help in interpreting the behavior of the furnace at a given time but the very rapidly moving particles and the intense radiation obscures what is happening very deep in the zone. This investigation was initiated in the hope that a better understanding of the combustion region could be obtained by using a high speed camera with a maximum speed of 3000 frames per sec. It seemed the best practical method of "slowing down" this characteristically violent action within the highly luminous field. Model studies and tuyere probing also have been used to aid in explaining the observed phenomena. Above the combustion zone, but below the fusion zone, there is probably a region in which the coke is comparatively stationary. Here are zones in which the gases must flow up through the granular bed counter to descending liquid slag and metal. There is no easy way to observe this zone in a blast furnace, but model studies have been of some help in explaining the nature of the zone and the laws governing the flow of the fluids involved. The whole problem is difficult and involved and any approach to a complete solution may require long investigation. This preliminary report has been written, therefore, because it is believed that appreciable progress has already been made that would be of interest to others. Tuyere Studies, Chemistry and Kinetics It is well known from the early work of Kinney and coworkers1,2 that combustion of carbon before the tuyeres appears to occur in two zones: Zone A: C + O, = CO2; AH77°F. = — 14,108 Btu per lb of carbon [I] Zone B: CO2 + C = 2CO; H77°F = + 6,183 Btu per lb of carbon [2] Zone A (Fig. 1) is close to the tip of the tuyere and zone B is somewhat farther back; there being a transition region in which both reactions occur. It is interesting to estimate the rate at which coke is burned before a tuyere with a wind rate of 90,000 cfm in a modern furnace having 18 tuyeres. Approximately 0.55 lb of carbon is consumed by eq 1 per tuyere per sec. A like amount disappears by eq 2 for a total consumption of 1.11 Ib per sec per tuyere. Assuming the coke is 85 pct C and has a bulk density of 30 lb per cu ft, this figure can be converted to a total of 1.30 lb of coke with a bulk volume of 0.043 cu ft disappearing per sec per tuyere. At the temperatures prevailing in the combustion zone (according to Kozlovich,³ he maximum is about 3400°F), the rate at which carbon is con-

Jan 1, 1953

By E. I. Salkovitz, F. W. von Batchelder

DURING the last few years several papers1-' have been published in which internal friction measurements have been used to determine the quantity of carbon or nitrogen dissolved in a iron. This method is based on the fact that, in pure Fe-N and Fe-C alloys, nitrogen and carbon cause peaks in the internal friction vs. temperature curve; at a frequency of 1 cycle per sec (cps) these peaks appear at $-200 and +360C, respectively, and if internal friction is expressed as Q-1, which is equal to times the logarithmic decrement, this figure will, by coincidence, give the weight percentage of nitrogen or carbon in solid solution.' In most of the studies published, very pure iron (Puron) was used. In one case the influence of manganese on the behavior of nitrogen in a iron was mentioned.4 It would be of great value, especially for the study of aging and related phenomena, if this method could be applied to commercial mild steel with norrnal percentages of manganese, phosphorus, sulphur, etc. As a rule, in such steels carbon and nitrogen are present together, and the amounts of these elements in solid solution should preferably be determined separately. The fact that their internal friction peaks appear at different temperatures (+36° and + 20°C in pure iron) seems promising for such a selective determination. It is necessary, however, that the peaks are narrow enough not to interfere with one another, and further, that there is no effect from carbon on the behavior of nitrogen in stress induced diffusion, and vice versa. According to Fast,' however, in the presence of manganese the nitrogen peak gets wider and appears at a higher temperature nearer the carbon peak, and thus the prospects for selective determination are reduced. (The carbon peak was not affected by the presence of manganese.) But even if fully quantitative de- terminations of the two elements are not attained, some relative figures on the sum of them and an indication of which one is the predominant one, would be of value. Some results from experiments along these lines will be reported here. An internal friction measuring device was assembled mainly following a description by KG." The measurements were also carried out as reported in that paper. Table I gives the chemical compositions of the four different materials used in this investigation. All materials were drawn to wires with diameter about 0.8 mm, and the analyses refer to these final shapes. Determination of Nitrogen Peak Wires from steels A, B, and C were decarburized in wet hydrogen (about 30 pct H2O) at 700°C until no carbon or nitrogen could be found by chemical analysis. No peak was then found in the internal friction. The wires were further annealed at 580°C for 16 hr in hydrogen bubbled through a solution of 6.8 pct NH3 in distilled water. Chemical analyses gave 0.04 pct N in A and C, and 0.06 pct in B. After annealing at 580°C for 15 min in a lead bath and water quenching, the internal friction was immediately measured. The resulting curves are shown in Fig. 1. At these high values of the internal friction the accuracy is comparatively poor; at Q-1 - 0.030 it is estimated to be 0.002. In order to make possible a calculation of the activation energy for diffusion of nitrogen, measurements were made at two different frequencies. Steel A shows rather broad peaks, and their temperatures can hardly be expected to be very accurate. Steels B and especially C are better in this respect. The finding of Fast' that manganese broadens the nitrogen peak is con-

Jan 1, 1953

By Secretary of the Interior

"INTRODUCTION The Bureau of Mines Synthetic Liquid Fuels Program again forged ahead during 1952, and important technical advances led the way to improved methods of converting coal and oil shale into liquid fuels. Marking the eighth year of activities under this program, the pact 32 months brought a new domestic industry nearer realization.The increasing demand for gasoline and oil and the rising cost of finding new petroleum, coupled with America's growing dependence on imports and the unsettled international situation, have continued to emphasize the importance of the Bureau's Synthetic Liquid Fuels Program. Oil, the indispensable material of wartime, likewise has critical importance in peacetime, touching as it does the life of every individual. Supplementing petroleum with synthetic liquid fuels will not only conserve this Nation's petroleum reserves but also will bring into greater use its tremendous reserves of coal, as well as the vast deposits of oil shale for which no other practical use has yet been found.The Bureau of Mines Synthetic Liquid Fuels Program is one of the most important and far-reaching of the Government's research projects. Through development of commercial synthetic liquid fuels, the United States can obtain oil products from its great inland reserves of coal and oil shale to supplement petroleum in any quantity that may be necessary, consistent with economic and other requirements, such as national defense. The use of raw materials from such deposits would be of highest importance in wartime, when shipping lanes are menaced by the enemy. The Synthetic Liquid Fuels Program of the Bureau of Mines and research efforts of industry have advanced. American technology to the point where it is now possible to begin the design and construction of prototype plants. Certainly, significant improvements will be made as the program continues, but this prospect in no way alters the fact that the start of prototype plants should be encouraged. These plants, as the first step in the development of a synthetic fuels industry, would serve a threefold purpose:"

Jan 1, 1953

By F. Gordon Smith

ALTHOUGH several geological indicators of the critical type are known, including quartz inversions and decomposition of hydrous minerals such as serpentine, there are very few of the general type. Solid solutions are excepted, but the limitations of use are very restricted and interpretations are sometimes ambiguous. General methods for determining temperature and pressure conditions during the crystallization of minerals would have considerable scientific and economic value. It is not the purpose of this paper to discuss the various methods of geological thermometry and barometry, but to present one general method, applicable to all minerals, and to describe what progress has been made in the methods of measurement. The general method, in brief, is a study of the stress conditions in and around various types of foreign inclusions which are trapped in minerals during growth. The method depends upon the fact that any homogeneous gas, liquid, or solid will in general have coefficients of thermal expansion and volume compressibility different from those of any given mineral. Therefore stress must develop in and around all types of inclusions in minerals if the temperature or the pressure, or both, are changed from the conditions which prevailed during the growth of the mineral. The methods of measurement consist of determinations of the temperature-pressure conditions of fit of the inclusions in the host mineral. The types of inclusions in minerals are: I—gas, or liquid plus vapor, when observed at room temperature, due to crystallization under pneumatolytic conditions; 2—liquid, or liquid plus vapor when observed at room temperature, due to crystallization under hydrothermal conditions; 3—glassy solid, or devitrified glass, due to crystallization under magmatic or high temperature metamorphic conditions, in a siliceous liquid; and 4—crystals, due to overgrowth of other minerals crystallizing simultaneously or of other minerals which crystallized previously. A survey of the literature shows that much valuable earlier work on inclusions, especially that car- ried out in England in the last century, has dropped out of current knowledge. The following is a brief summary of the significant contributions to the problem up to the present day. Davy in 1822 asserted that fluid inclusions in minerals consist of an aqueous solution of salts and a gas bubble, the whole being either at lower or higher pressure than atmospheric.' At intervals from 1823 to 1862, Brewster contributed information concerning other types of inclusion consisting of 1—aqueous solution, a much more expansible liquid, and a gas; 2—aqueous solution, salt crystals, and a gas; and 3—the very expansible liquid and a gas. The very expansible liquid fills the gas space between 20" and 30°C. Compression strain effects were seen around inclusions in diamond, topaz, and other minerals.'-" Sorby in 1858 and 1869 further advanced the study begun by Davy, stating that fluid inclusions represent a sample of the mother liquor of crystallization and that the degree of filling of aqueous inclusions at room temperature defines the temperature-pressure relations during formation of the host. The degree of filling may be measured by determining the minimum temperature of filling of the inclusion by the liquid phase. The very expansible liquid in some fluid inclusions is liquid carbon dioxide. The temperature at which salt crystals in fluid inclusions completely dissolve in the fluid is the minimum temperature of formation. Inclusions of glass or devitrified glass indicate crystallization from a melt. Inclusions of crystals in minerals are often centers of strain, which may be seen by optical effects or by radial tension cracks. Sorby realized that an analysis of stress-strain relations about inclusions could be used to provide precise data on the temperature of crystallization, but the matter was never pursued.' , Hartley (1876, 1877),".'" Hawes (1881)," Wright (1881),'V ohnsen (1920),I3 and Holden (1925)"

Jan 1, 1953

By J. W. Freeman, E. E. Reynolds, A. E. White

Fram a study of 63 systematic alloy modifications it was found that molybdenum, tungsten, and columbium, added individually or simultaneously, and increases in chromium cause major improvements in 1200°F rupture strengths of Cr-Ni-Co-Fe base alloys. Rupture strengths were a function of the effect of composition modifications on both the inherent creep resistance and the amount of deformation the alloy would tolerate before fracture. THIS paper describes the results of an investigation of a series of alloys with systematic variations of the chemical composition of the following basic alloy: C, 0.15: Mn, 1.7; Si, 0.5; Cr, 20.0; NI, 20.0: Co, 20.0: Mo, 3.0; W, 2.0; Cb, 1.0; N, 0.12; Fe, 32.0 pct. The 62 modifications of this alloy were produced under conditions which minimized all factors influencing properties at high temperatures except composition. Melting, fabrication, and heat treatment were carefully maintained constant. Stress-rupture properties at 1200°F were used as the primary criteria of evaluation of the alloy. The objective of the study was to obtain data for determining the fundamental role of the influence of alloying elements on properties of heat-resistant alloys at high temperatures. In addition the results should be useful in determining optimum chemical compositions, the sensitivity of properties to variations in composition, and the degree to which alloy content could be reduced while retaining worthwhile properties. It is difficult or impossible to develop correlations between properties at high temperatures and systematic variations in chemical composition from published data for wrought heat-resistant alloys developed for gas turbines.' ' The main reason for this is the extreme dependence of the properties on conditions of treatment of the alloys." In most cases variation in final treatments between alloys so influences the properties that the influence of chemical composition is obscured. In addition it is recognized Table I. Basic Alloy and Some Modifications Used Basic AllOy, Variations in Element Pct Composition, Pct C 0.15 0.08. 0.40. 0.60 Mn 1.1 0.03,0.25.0.50,1.0,2.5 S1 0.50 1.2, 1.6 Cr 20.0 10, 30 Ni 20.0 0, 10,30 Co 20.0 0. 10, 30 MO 3.0 0. 1.2.3, 5, 7 W 2.0 0, 1, 5, 1 Cb 1.0 0.2,4,6 N 0.12 0.004, 0.08, 0.18 Fe 32.0 that variations exist between heats of the same alloy which are related to melting practice and that there is a strong possibility that conditions of hot working influence response to final treatments. The development of heat-resistant alloys has been based on the gradual accumulation of data roughly related to composition from extensive testing programs. There is every reason to believe that in most cases the optimum compositions have been achieved by this procedure in the alloys commercially available. There are, however, very little data showing the influence of systematic variations of composition free from the influence of other factors, particularly for alloys of the type investigated. Several investigators of cast alloys have demonstrated compositional effects, notably Grant,1-6 Epremian,t Guy,8 and Harder and Gow.9 Sykes10 eviewed the work on the wrought alloy Rex 78 and the systematic variations of carbon, copper, molybdenum, and cobalt leading to the development of the stronger Rex 337A alloy. From the papers by Wilson11 and Henry12 it is possible to deduce the beneficial effect of substituting cobalt for iron in 0.45 pct C-20 pct Cr-20 pct Ni-4 pct Mo-4 pct W- 4 pct Cb alloys. Wilson mentioned but did not present the extensive compositional studies involved in developing these alloys. Binder" showed optimum properties for 3, 2, and I pct, respectively, for molybdenum, tungsten, and columbium in 20 pct Cr-20 pct Ni-20 pct Co-30 pct Fe alloys for limited systematic variations of these

Jan 1, 1953

By M. Semchyshen, G. A. Timmons

The predominant orientation in both straight-rolled and cross-rolled molybdenum is the {100} [110] texture. Upon complete recrystallization, this same texture predominates, but there is less spread about the ideal orientation. A secondary orientation about the [111] direction as the axis develops in cross-rolled sheet. Compression-rolled sheet exhibits random orientation in the plane of the sheet. Some mechanical properties were measured at varying angles to the rolling direction to determine the effect of preferred orientation on anisotropy in molybdenum sheet which had been straight, cross, or compression rolled. THE development of the arc-cast process has made available large ingots of molybdenum from which it is possible to roll sheet of considerable size. It is anticipated that such sheet will be further fabricated by spinning, drawing, stamping, or forming. Anisotropy of physical properties caused by the preferred orientation developed in the sheet during rolling may be expected to affect the behavior of the metal when subjected to these fabricating operations. To produce a sheet which will be most amenable to the fabrication of a given shape by a particular operation, consideration should be given to the directions and magnitudes of plastic deformations produced in the operation. When possible, the rolling schedule should be controlled to develop a texture which favors the required deformation. The existence of preferred orientations in rolled molybdenum sheet has been reported by Jeffries,' Konobejewsky,' Fujiwara," Goss,' and Ransley and Rooksby." None of these investigators obtained sufficient X-ray data to permit the construction of pole figures; instead, they based their conclusions upon Debye-Scherrer patterns of a limited number of positions. Ransley and Rooksby devoted some attention to transcrystalline cleavage at 45" to the rolling direction, indicating that it is appreciable in polycrystalline material only when the crystals are in the ideally preferred condition, and that this condition is only approached if the metal has been rolled successively in two perpendicular directions. In a recent paper, Custers and Riemersmao introduced the first pole figures to describe the textures of straight-rolled and cross-rolled molybdenum sheet. To increase the knowledge concerning the generation and effects of preferred orientations in molybdenum sheet, an investigation was undertaken to determine the effects of variations in rolling schedule and annealing treatments on preferred orientation, and to correlate preferred orientations with some mechanical properties. The orientations of straight-rolled, cross-rolled, and compression-rolled sheet have been determined by X-ray analysis, both as-rolled and after recrystallization. Pole figures have been constructed to describe the textures produced by these various rolling procedures. Texture of Cast Molybdenum Ingots In the arc-cast process, molybdenum powder is pressed into a vertical column which is sintered to increase its strength as it proceeds downward into a water-cooled mold, where the metal is melted in an alternating-current arc established between the end of the formed powder electrode and the metal bath at the top of the growing ingot. Since the solid-liquid interface moves continuously upward in the mold, the crystal axes are not normal to the cold surface of the mold but have the curvature shown in Fig. la. X-ray analysis reveals that the cube axis is the fiber axis and that it is normal to the cold surface of the mold; that is, the [loo] direction is parallel to the longitudinal axis of the ingot. This substantiates recent work by

Jan 1, 1953

By W. M. McCardell, W. O. Winsauer

The abnormal conductivity found in shaly reservoir rocks containing an electrolyte is shown to be a consequence of the electrical double layer in the solution adjacent to charged clay surfaces. This increased conductivity results from a higher concentration of ions in the double layer than in the solution in equilibrium with the double layer. It is shown that the magnitude of the increased conductivity of a shaly reservoir material is influenced by the concentration and type of ions in the equilibrium solution as well as by the colloidal nature of the rock. INTRODUCTION An important factor in the quantitative interpretation of the electric log is the resistivity factor of reservoir rock. The resistivity factor is defined as the resistivity of the rock when completely saturated with an electrolyte divided by the resistivity of the electrolyte itself.' In the normal case, the resistivity factor for a particular rock sample is independent of the resistivity of the electrolyte and reflects the pore geometry of the rock.' In 1949. Patnode and Wyllie' showed that in some cases the resistivity factor is not constant, but instead varies with the resistivity of the electrolytic solution. It was shown that clean sands behave normally—i.e., that the resistivity factor does not vary with resistivity of the electrolyte — but that sands con- taining shale and clay may exhibit abnormally low resistivity factors when the solution used to saturate them is of fairly high resistivity. At low resistivities of the electrolyte, the resistivity factor for a shaly sand appeared to approach a normal behavior. It is evident that the resistivity factor of a shaly sand is dependent upon factors other than pore geometry when the solution used to saturate it is of high resistivity. Patnode and Wyllie, and later de Witte,' assumed that the conductivity of a shaly sand saturated with an electrolyte could be represented as the sum of two quantities. One of these was assumed, in effect, to be the conductivity which would be expected if the sample were a clean sand. and the other was assumed to be a conductivity inherent in the sample itself. The latter was supposed to be constant for a given rock sample regardless of the solution used to saturate it. The source of this added conductivity was ascribed to "conductive solids." In actual practice: the effect of the abnormal behavior of shaly sands is of minor importance except when the resistivity of a formation such as a sand is high. Thus the effect is more important when the sand is saturated with a dilute brine than when it contains a more concentrated electrolyte. The effect is also more important when the sample contains oil or gas than when it contains only saline water. Recently it has been suggested that the porosity of a stratum may be estimated from the electric log by use of the resistivity of the invaded zone." This is the zone flushed with the filtrate from mud used in drilling the well. which is ordinarily very dilute brine. When the method is applied to shaly sands, the effect of abnormal conductivity becomes of importance. This report describes an investigation of the mechanism responsible for the abnormal behavior of the resistivity of shaly rock saturated with conducting solutions. The investigation

Jan 1, 1953

Jan 1, 1953

By Thomas Fraser

The Convertol process, recently developed in western Germany, is a new method of cleaning and dewatering coal-washery slurries. It is a modified bulk-oil process, in which a very small quantity of heavy oil is dispersed over the surfaces of the coal particles, followed by a screen centrifuge operation in which the water and dirt (clay, shale, and pyrite particles) are thrown out through the screen perforations and the clean coal particles are retained on the screen and discharged as a dewatered, clean coal product of 8- to l0-percent surface moisture. It is reported, also, that the process oil, all of which is retained in the clean-coal product, adds to the coking power of the coal and facilitates the production of briquets, reducing the proportions of binding material required.

Jan 1, 1953

By E. F. Reed

CONSIDERABLE deep hole prospect drilling has been done in the last few years in the Globe-Miami mining district about 70 miles east of Phoenix, Arizona, and in the San Manuel-Tiger area about 50 miles south of the Globe-Miami region. More than 205,000 ft of churn drilling have been completed by the San Manuel Copper Corp. at their property in the Old Hat Mining District in southern Pinal County. The deepest hole on this property is 2850 ft; there are 49 holes deeper than 2000 ft. At the adjoining Houghton property of the Anaconda Copper Mining Co., where only one hole reached 2000-ft depth, there were 27,472 ft of churn drilling and 3436 ft of diamond drilling. Three churn drill holes were deepened by diamond drilling methods. Near Miami in the Globe-Miami district the Amico Mining Corp. drilled four holes by combined churn and rotary drilling methods, the total amounting to 13,879 ft, of which 2256 ft were drilled with a portable rotary rig. In the same district, besides doing a large amount of shallow prospect drilling, the Miami Copper Co. drilled two holes of 2560 and 3787 ft, respectively, which were completed by churn drilling methods. The rocks encountered in drilling at San Manuel and Tiger are described by Steele and Rubly in their paper on the San Manuel Prospect' and by Chapman in a report on the San Manuel Copper Deposit.' The rocks are well-consolidated Gila conglomerate, quartz monzonite, and monzonite porphyry. In some places these formations stand very well while being drilled, and three holes were drilled without casing, the deepest of which was 2200 ft. In other holes faulted and fractured ground made drilling difficult. In the Globe-Miami district the deep drilling was done in the down-faulted block of Gila conglomerate east of the Miami fault and in the underlying Pinal schist. The geology of this area is described by Ranaome. In the Amico holes the conglomerate varied from material consisting entirely of granite boulders and fragments to a rock made up of schist fragments in a sandy matrix; in the Miami Copper Co. holes there were more granite boulders and the material was poorly consolidated. Drilling was much more difficult and expensive in the Miami area than in the San Manuel district, mainly because of the depth of the holes and the formations drilled. All the deep hole prospecting described in this paper was done with portable rigs. The churn drill rigs were of several types, of which the Bucyrus-Erie were the most popular. Bucyrus-Erie 28L, 29W, and 36L rigs were used on some of the deeper holes on the San Manuel property. A few Fort Worth spudder types were tried, and the deepest hole at San Manuel was drilled with a Fort Worth Jumbo H. The spudder type is considerably larger than most other rigs used on this work and required a larger location site. The spudders were belt-driven machines with separate power units, and time required for setting up and moving was much longer than with the more portable drills. All the churn drilling was done by contractors or with machinery leased from them. A few of the contractors had complete equipment, including most of the necessary fishing tools. Unusual and special fishing tools were obtainable from the supply companies in the oil fields of New Mexico or in the Los Angeles area. Most of the contractors used equipment with standard API tool joints, so that much of it was interchangeable. Failure of tool joints is one of the principal causes of fishing jobs. It can be minimized if the joints are kept to the API specifications and the proper sized joints are used in the various holes. The minimum sizes that should be used with various bits are as follows: 12-in. and larger bits, 4x5-in. tool joints; 10-in. bits, 3Y4x41/4-in. tool joints; 8-in. bits, 23/4x 3 3/4-in. tool joints; 6-in. bits, 21/4x31/4-in. tool joints; 4-in. bits, 15/ix25/s-in. tool joints. Two rotary drill rigs were tried at San Manuel on the same hole, and a portable rotary drill rig was used on the Amico drilling for test coring the formation and for drilling in holes 3 and 4. Rotary drilling differs from churn drilling or cable tool drilling in that the bit is revolved by a string of drill pipe and the cuttings are removed from the hole by a thin solution of mud pumped through the drill pipe. The principal parts of a rotary rig are the power unit, a rotating table to revolve the drill pipe, hoists to raise and lower the pipe and to handle casing, and a pumping system to circulate the drilling liquid. The rig used on the Amico property at Miami was mounted on a truck. The larger rig used on the San Manuel property was hauled by several trucks and had separate turntable and pumping units. Diamond drill coring equipment was used successfully with the rotary rig in the holes on the Amico property. To allow for 2-in. drill pipe with tool joints, 31/2-in. core barrels and bits were used. With the standard 31h-in. core barrel there was considerable difficulty in maintaining circulation with mud, so a barrel was designed with a smaller inner tube and a broad-faced bit. This allowed coarser material to circulate between the barrels. Rock bits of 5 to 37/8 in. were used with the rotary rig for drilling between core runs. Diamond drill equipment is much lighter than churn drill tools, so that fishing tools can usually be obtained from supply houses by air express when needed. Three churn drill holes on the Houghton property at Tiger were deepened by diamond drilling with Longyear UG Straitline gasoline-driven machines. The open churn drill hole was cased with 21h-in. black pipe. In deep hole churn drilling, casing is one of the most important items, especially in drilling in un-consolidated material like the formations drilled by

Jan 1, 1953