Search Documents

By M. H. Forester

The Bituminous Coal Industry has for the past year been faced with a most serious problem. I am sure that you have had your own individual and local problems, as do we all. In my thirty years of practical experience with coal mining, I have never found an operating man nor a coal mine without problems. The very nature of mining, with so many unknown factors involved, precludes the absence of problems. But they are not insurmountable, and one should not dwell on them interminably. They should be recognized as a challenge to our ability and ingenuity to solve them, and once the proper solution is found, it should be applied and the problem dismissed. However, we find ourselves at the moment in the midst of a serious challenge to our very existence. In the early thirties, many in the industry welcomed the re-establishment of Unionism as a balance wheel, in the belief that the stabilization of wage scales would also stabilize prices and eliminate disastrous price cutting practices. The ultimate effects of having twenty-six years of benevolent paternalism in the administrative branches of Federal and State Governments with their labor courting policies, could hardly have been anticipated. And so with wages spiralling under government sponsorship, we have finally reached the point where competitive fuels, such as natural gas and oil are more attractive to the consumer, from the economic angle of cents per BTU cost, than coal.

Jan 1, 1953

By J. Venter

The history of firedamp is the same as that of coal: The initial stage was the accumulation of vegetation, which was converted into peat under certain local conditions, then lignite, bituminous coal, and finally anthracite. These deposits ceased to increase owing to inundation that deposited earthy sediment, sometimes as much as several tens of meters (several tens of yards). The vegetable matter, whether it was covered with sediment or not, began to ferment. The basic organic components of the vegetable matter are: Cellulose, lignin, and wax and resin in varying proportions, according to the different kinds of vegetable matter. There are, in addition, some impurities, generally mineral.

Jan 1, 1953

In the years prior to the outbreak of war in 1939 Australia's production of copper had declined from a peak of about 80,000 tons in 1911-1915 to approximately 25,000 tons in 1939. This production met the need of the slowly growing national requirement and gave an excess for export. However, with the intensification of the war effort in 1942 due to the imminence of a Japanese invasion of this country, or at least a blockade of the sea lanes, it became necessary to expand production of armaments, and consequently the demand for copper increased beyond the capacity of the industry. Importation of copper to Australia during the period 1940-1944 was 131,000 tons.When exploration of the Mount Isa orebody was first being carried out in 1928, No. ID diamond drill disclosed the presence of some copper ore lying outside the limits of the Black Star orebody2, but it was not until 1941-1942 that the development of No. 7 level in the Black Star orebody enabled the existence of a lode of copper ore of economic grade to be established. At the request of the Commonwealth Government of the day a programme of development for copper production was undertaken whilst lead smelting was continued as before the war.A series of flotation tests on up to 1,500 tons of ore at a time, was undertaken and the concentrate so obtained was stockpiled. These tests were conducted, using one section of the lead mill, and demonstrated that a concentrate grade of 22-23% Cu with a recovery of 80-85% might be expected.These recovery figures were afterwards much improved, and 93-95%was obtained before the close of smelting in 1946.

Jan 1, 1953

By The Honourable George Prudham

"I AM PLEASED indeed to be present with you here today and to be taking part in the proceedings of your convention. You have been greeted and welcomed to the Province by Premier Manning who is also provincial Minister of Mines and Minerals, and to this City by Mayor Hawrelak. As Minister of Mines and Technical Surveys in the federal government and as Member of Parliament for Edmonton West, I have been asked to share the honour of extending greetings and a cordial welcome to all.It is a happy coincidence that this representative national gathering, indicative of the growing strength and significance of a great basic Canadian industry, is taking place in the Macdonald Hotel, the new addition of which marks another important step forward in the progress of this City and district.This happens to be the third national convention of the C.I.M. that I •have had the pleasure of attending and I trust that I am not presumptuous in expressing the hope that I will have the opportunity of attending many more conventions of the Institute in my present capacity.Dr. Kidd has bestowed on me a high honour by asking me to be Co-Chairman of this Inaugural Session of the Convention and thus to share with him the responsibility of presiding over the proceedings of this afternoon."

Jan 1, 1953

By S. W. Zoldok

[The Bull Valley iron-ore district lie,; in the northern part of Washington County, Utah, approximately 30 airline miles southwest of the highly productive Iron Springs area (fig. 1). Iron-ore occurrences in the district have been known for many years, but they have not been mined, largely because of the inaccessibility of the area. The Bureau of Mines established a development project in the Bull Valley district in September 1941. Two separate areas, the Pilot and the Cove Mountain, were investigated. The work was planned to increase iron-ore reserves for steel production in the Western United States. During the project period three diamond-drill holes aggregating 1, 000 feet were completed (fig. 2). The program also included 6 408 linear feet of surface trenching and 171 feet of underground work (figs. 2 to 8, inclusive). Analyses were made of 460 samples from the diamond-drill holes and surface and underground excavations. The results of the analyses are given in tables 1, 2, 4, and 5, and the logs of the diamond-drill holes are shown in table 3. Field. work was completed in September 1942.]

Jan 1, 1953

By Ruddle R. W.

Magnetite occurs in the reverberatory furnaces, blast furnace and converter (a) as the result of its presence in the materials charged, and (b) as the result of oxidation of the FeS in the charge in the absence of sufficient SiO2 to slag the FeO as it is produced and thus prevent its subsequent further oxidation. Magnetite is reduced by FeS according to FeS+3Fe3O4=10FeO+SO2 and similar reactions. This reaction is markedly affected by temperature and does not proceed to any important extent below about 1200°C. To ensure comparative freedom from magnetite it is therefore necessary to raise the temperature of the furnace to the highest practicable figure and to use plenty of siliceous flux. Since the maximum operating temperature is likely to be limited by the resistance of the refractories to attack by the slag, investigation of the factors affecting this attack should be helpful. It is reasonable to suppose that the formation of magnetite might be minimized by ensuring intimate admixture of matte and slag during conversion so that silica is readily available for combination with ferrous oxide as the latter is formed. The literature gives no clue to the importance of this factor and some experimental work on this aspect might be fruitful

Jan 1, 1953

By J. W. Putman, N. J. Grant, D. S. Bloom

SEVERAL recent determinations of the melting S point of pure chromium have been reported which give values of 1845°C1; 1895°C,² 1930°C,³ 1860°C,' and 1890°C.5 because of this wide spread of values, it appeared desirable to make one additional attempt to obtain a more accurate, reliable figure. bloom and Grantx recently reported a phase transformation in chromium:.--- it was desired to check this, too, in the course of checking the melting point. To accomplish this, a much higher purity chromium was required. Electrolytic chromium containing about 0.5 pct 0 was crushed to a finer size and was then annealed in highly purified, dried hydrogen at 1375°C for 100 hr. This treatment produced chromium with about 0.008 pct 0, 0.002 pct N, and negligible carbon. The balance of the impurities was 0.3 pct Fe, 0.03 pct Si, 0.004 pct S, and less than 0.001 pct Mo. This chromium was melted in a stabilized zirconia crucible under pre-purified argon, using induction heating. Temperature measurements were made with annealed wolfram-molybdenum thermocouples and a Leeds and Northrup Speedomax Recording Potentiometer. The thermocouples were annealed for 1 min in hydrogen at a temperature of about 2400°C. Each leg of the thermocouple was immersed in an ice-water mixture using mechanical connectors to the lead wires. The thermocouple tip was immersed in the molten chromium in a zirconia protection tube which introduces an error of about 3°C as a temperature drop through the walls of the tube. The weight of chromium was about 183 g. The dimensions of the melt in the crucible were about 1.25 in. diam x 2 in. high. The tip of the thermocouple was held about ½ in. from the bottom of the crucible. Two new thermocouples were used with the above set-up giving the results shown in Table I. Since this chromium is purer than that used by Greenaway, Johnstone and McQuillan,' by Carlile et al.,4 and other investigators,²,3 it is believed to be the more accurate. Thermocouple aging effects which are believed responsible for the high value of 1930°C³ were avoided in this work. This value of 1903°C is correct to about ±10°C. The right hand column lists the temperature of the a ? ß transformation on heating and the ß ? a on cooling.3 A sample curve is shown in Fig. 1. The value so determined is 1840°C + 15°C. Fig. 1 gives adequate evidence that there is a transformation in chromium at high temperatures.' References 'H. T. Greenaway, S. T. M. Johnstone, and M. K. McQuillan: High Temperature Thermal Analysis USing the Tungsten-Molybdenum Thermocouple. Journal Inst. Metals (November 1951) 19, p. 109. ²J. W. Putman, R. D. Potter, and N. J. Grant: The Ternary System Chromium-Molybdenum-Iron. Trans. A.S.M. (1951) 43, p. 824. ³D. S. Bloom and N. J. Grant: Chromium-Nickel Phase Diagram. Trans. AIME (1951) 191, p. 1009; Journal of Metals (November 1951). ' S. J. Carlile, J. W. Christian, and W. Hume-Rothery: The Equilibrium Diagram of the System Chromium-Manganese. Journal Inst. Metals (1949) 76, p. 169. 5G. Grube and R. Knabe: Ztsch. Elektrochemie (1936) 42, p. 793.

Jan 1, 1953

By R. F. Mehl, R. W. Parcel

THE rate of the decomposition of austenite in eutectoid steels, forming only pearlite, may be expressed fundamentally in terms of the rate of nucleation and the rate of growth of pearlite nodules. This matter has received much attention in recent years. (The basic references are listed in ref. 1; references of particular import to the present work will be given separately.) Systematic data have been developed for plain carbon eutectoid steels.:! Although the physical factors affecting the rate of nucleation, N, in case of plain carbon steels have presumably been identified, they cannot as yet be evaluated quantitatively.' Several somewhat successful attempts, however, have been made to calculate the rate of growth, G. In the latter case the important factors determining the edgewise growth of pearlite have been assumed to be: 1—the interlamellar spacing; 2—the concentration extremes and concentration contours of carbon in austenite in front of the growing pearlite interface; and 3—the rate of diffusion of carbon in austenite.* The only systematic data on N and G for pearlite in alloy eutectoid steels are those for Co-steels;6 there are no data on alloy eutectoid steels in which the alloying element is known to decrease the rate of formation of pearlite, apart from a few scattering data reported earlier' for steels containing manganese. This paper reports a systematic study of N and G for eutectoid alloy steels containing molybdenum and nickel, respectively. In order to provide information of help in understanding the results, new data are presented on the effect of molybdenum on the interlamellar spacing of pearlite, So; data on the effect of nickel on So have already been published.' The alloys used were in five groups: 1—Pure Fe-C-Mo alloys (Table I) were supplied by the Climax Molybdenum Company of Michigan, Detroit. They were made from Armco ingot iron of standard analysis, Acheson graphite, and ferro-molybdenum, melted in silica-lined crucibles in a high frequency induction furnace. The ferromolyb-denum was added to the melted steel, followed in 5 min by 0.08 pct Al. The ingot as-cast measured 23/4x 31/4x10 in.; it was hot-forged at 1150°C to a bar 1 in. sq.

Jan 1, 1953

By R. B. Burt, J. A. Barr, I. S. Tillotson

THE pumping of solids in water suspension is an important part of many metallurgical and mining operations. In most cases, it is still in the rule of thumb category for which no universal formula has been developed, and much research is needed. Because of the limited and incomplete data available, this article may be classed as an experience paper, which is presented with the hope that some contribution will be made toward the development of the so-called universal formula. This formula, if and when developed, may be evolved from several factors, many of which are not now available for general application. The designing engineer is interested in obtaining accurate forecasts on: 1—the minimum velocities needed to prevent choke-ups in the pipeline, which in turn dictates pipe sizes, 2—power required for pumping, 3—pump selection. The basic factors for a given problem will include: 1—weight per unit of time of solids to be handled, 2—specific gravity of solids, for calculation of volume, friction and power, 3—screen analysis of solids with the colloidal acting, i.e., the slime fraction, a very important factor, 4— shape of particle or some means of determining a friction constant, 5—effects of percentage of solids, 6—development of a viscosity factor to be used in the overall calculations, 7—calculation of the lower limits of pipeline velocities permissible, 8—calculation of total head, pump horsepower, and 9—setting up of pump specifications. In certain limited cases horsepower and total heads and minimum velocities may be computed and a suitable pump selected from basic data, but in many cases, as in mining of Florida pebble phosphate, experience rather than a hydraulic formula still should be used as a basis of selection. Pumping Florida Pebble Matrix Pumping at the Noralyn mine of International Minerals and Chemical Corp. will be used as an example. Other areas will vary as to the characteristics of the matrix, especially the slime content. A typical screen analysis of this matrix is: +14 mesh, pebble size,* 2.1 pct; —14 +35 mesh, 11.4 pct; -35 +I50 mesh, 60.5 pct; -150 mesh, 25.0; total, 100 pct; moisture in bank, 20.0 pct; weight per cu ft in bank, 120 lb. The —150 mesh fraction may increase to as much as 35 pct in adjacent areas. When thoroughly elutriated, the matrix has a relatively slow settling rate, which is an important factor in permitting lower pipeline velocities without choke-ups. Exact data is not available to evaluate settling rates. For a factor of 100 a suspension of clean building sand in water is suggested. When pumping long * Pebble is a commercial designation for the coarser fraction of finished phosphate from a washer, usually +14 mesh. distances, a quick settling matrix allows the coarser solids to settle out along the bottom of the pipeline, causing drag, turbulence, and increased friction. With a slow settling matrix as at Noralyn, turbulence acts to keep the solids in suspension at a lower friction head, regardless of the pumping distance. When the pebble content of the matrix, i.e., the + 14 mesh fraction, is in excess of 10 pct of the total solids, trouble may be expected from settling out even in normal pumping distances. To prevent choke-ups and maintain tonnage, an additional pump must be added in the long runs, where one pump would otherwise be satisfactory. A typical pulp handled is: total volume, 7800 gpm; water, 4500; solids pumped per hr, 4200 lb; sp gr pulp, 1.4; percent solids in pulp, 46.; pipe size, 16-in. ID; pulp velocity, 12.85 fps; probable critical velocity, 10 fps, as below this minimum velocity choke-ups would be numerous. In calculating friction heads the Armco handbook is used where a roughness factor based on 15-year-old pipe is set up. Because the pipe used in pumping matrix is smooth and polished because of the scouring action of the phosphate and its silica content, the head losses in the Armco table for water are practically the same as in pumping the Noralyn matrix through smooth pipe, plus the fact that conditions vary widely over short periods, making accurate determinations difficult to obtain. New pumps and pump changes are being tested continuously and a wealth of data built up. This has resulted in a substantial improvement and lower relative costs in pumping matrix. The Florida phosphate industry is constantly seeking to offset higher wage and material costs with improved technique. Until a few years ago a 12-in. discharge pump was commonly used, with heads as low as 80 ft. Sizes have gradually increased and heads more than doubled. For example, the following pump was placed under test at the Noralyn mine: make, Georgia Iron Works; size, suction 16 in., discharge 14 in.; impeller, 39-in. diam; motor, 600 hp, slip ring; full load speed, 514 rpm. The results were increased head, higher capacity than the older design, with fewer pumps in the line from mine to washer.

Jan 1, 1953

By Milton H. Fies

THE writer wishes to acknowledge at the outset his great sense of obligation to those who contributed so broadly and expertly to the preparation of this paper: Dr. Albert DeSmaele, Chairman of the Board of Directors of Socogaz, Belgium; Dr. Julien Venter, Director of the National Institute of Coal Mining, and Coal Utilization Industry, Belgium; Dr. Roger Loison, Chief Engineer, French National Coal Research Board, France; and Dr. Erich Sarapuu of the Sinclair Coal Co., Kansas City, Missouri. Liberal use has been made in this paper of a recent publication on Russian, Italian, Belgian, and French experiments prepared jointly by the Centre d'Etudes et Recherches des Charbonnages de France (Cerchar) and the Institut National de I'Industrie Charbonnière of Belgium (Inichar) .l The writer is particularly indebted to Dr. E. T. Wilkins, of the Fuel Research Station, London, and to Mr. James L. Elder, of the Alabama Under- ground Gasification Experiment at Gorgas, Alabama, for their unfailing patience and effective support. Not only did these experienced and capable men edit and revise this discussion, but much of its content is a direct contribution quoted in full from their memoranda. Without the assistance of all these colleagues, this presentation would not have been possible. It has been a privilege to serve and work with them and to acknowledge repeatedly their loyal cooperation. The recovery of the energy inherent in coal beds throughout the world has been done through the years by methods that today may be justly regarded as primitive. While the techniques of coal mining through the application of machines and the enhancement of information and skills have advanced to an extraordinary extent, particularly during the past 20 years, the underlying means is essentially the same as when man first began to mine coal. Despite this progress in the manner of coal mining, it continues today as a hazardous, toilsome, grimy task. Coal mining per se has advanced at a greater and more rapid stride in the past 25 years than the mining of any other mineral, but the basic method is fundamentally the same as it was the first day a miner took a pick into his hands many centuries ago. This situation presents a challenge to mining engineers everywhere, from

Jan 1, 1953

By E. P. Carman

This: report gives data on the installation and operation of a packaged-unit heat-pump installation in a residence in McLean, Va., a suburb of Washington, D. C. The original equipment, installed in January 1947, was one of the first of 50 experimental Marvair units manufactured by the Muncie Gear Works, Inc., Muncie, Ind. The compressor unit of this installation was replaced by the company in September 1947, with a modified commercial model. The commercial unit and the original pump and fan accessories have been used as the sole means of heating (and cooling in summer! the. residence for the subsequent five winters and summers. The conclusions and data given herein, therefore, cover 6 winters sad 6 summers of heat pump operation, including 1 winter when temperatures averaged below normal for 2 months and the following summer when temperatures were above normal.

Jan 1, 1953

By Dart Wantland

"AbstractThe scope of geophysics in civil engineering and the nature of exploration geophysics are briefly discussed. Engineering problems amenable to geophysical attack are illustrated by specific examples. The various methods available, accuracy of results, and costs are treated. The possibilities of new uses of geophysical techniques are pointed out.IntroductionTHE SCOPE of geophysics in engineering is different than in oil or mining exploration. In civil engineering, geophysics solves specific problems; as for example, what is the depth to bed-rock along the axis of a proposed dam? The area to be surveyed is of limited extent, and the subsurface information .sought is relatively near the surface. The engineering geophysicist is not called upon to investigate geological basins or extensive mineralized areas or to probe for data to thousands of feet in depth. The geophysical tools employed in the three fields are, however, quite similar; the differences are mainly in the objectives.The Natural Geophysical ExplorationThe terms geophysics and geophysical exploration have been used heretofore and will .be employed in what follows. The question is, therefore, What is geophysical exploration?Geophysical exploration is a line of field work where measurements are made at the ground surface with special instruments to get geological subsurface information. Briefly stated, geophysics is a form of exploration that supplements geological work. It is a blend of physics and geology since physical measurements are made •at the surface of the ground that can be interpreted in terms of subsurface conditions."

Jan 1, 1953

By B. P. Martinez

A process for regenerating spent pickle liquor is proposed in which some of the water is evaporated at atmospheric pressure and ferrous sulfate is precipitated as monohydrate crystals..Equilibrium conditions are set for a slurry of crystals in a mother liquor containing 5 percent FeS04 and 45 percent E2S04, by weight, and boiling at about 235° F. The slurry is pumped continuously to a filter, and the mother liquor from the filter is pumped back for reuse in the pickling tanks. The net result of the process is to remove ferrous sulfate in the regeneration plant at the same rate ac it is produced in the pickling tanks. This process is integrated with the steel-pickling operation and controlled by the pickling requirements for particular steels. Spent pickle liquor is removed for regeneration continuously from both batch and continuous picklers at higher acid concentrations than would be dumped to waste because no acid is neutralized or discarded. However, the process is not designed to keep a sulfuric acid concentration stronger than 25 percent in any pickling tank. To retain flexibility in the pickling operation, all acid makeup is added to the pickling tanks. Rinse waters are used as water makeup for the pickling tanks. To further minimize waste of acid in the rinse waters, improvements of rinsing practices are outlined.

Jan 1, 1953

By W. D. Walker

The trend toward encouragement of worker participation in accident prevention in the coal mines of the United States is not new; however, it has been given added impetus in recent years and is now definitely progressing. It has been found by experience that, although there are many approaches to a mine-safety program that will include the workers themselves as well as their supervisors, no one way is suitable under all circumstances. It requires the concerted efforts of many agencies working along parallel lines toward a common goal. The following seven principal agencies, using somewhat different methods, are listed to illustrate how this problem is approached throughout the coal-mining industry 1. Federal Bureau of Mines. 2. State mining departments (in individual States where coal is produced). 3. Programs conducted by individual mine operators. 4. Programs conducted by mine workers' organizations (unions). 5. Institutes, societies, and other educational organizations. 6. Coal operators' associations (regional and national). 7. Universities, college, and high schools. Each of the seven approaches to safety are discussed briefly, and their methods end contributions, such as publications and other activities, are listed.

Jan 1, 1953

By Constantine C. Popoff

The Hermada antimony deposit is in the Sewtooth Range in southwestern Idaho, about 77 miles by road northeast of Boise. Stibnite mineralization occurs over an area one mile wide from west to east and two miles long. It is locally referred to as the Swanholm district. In 1947 high- grade stibnite ore was discovered on the East Fork of Swanholm Creek. Since then, ore in commercial quantity has been produced by the Hermada Mining Co. The total output for 1947-50 was about 5,000 tons of ore, containing 640 short tons of antimony metal.

Jan 1, 1953

By J. L. Morning

During recent years, the Bureau of Mines has conducted an extensive investigation of the materials for making iron and steel. This work includes iron ore concentration, agglomeration, direct reduction of iron ores and concentrates, the production of pure manganese, chromium, and cobalt by electrolytic processes, the production of ferroalloys from low-grade domestic ores, and the development of special alloys to utilize these products. As a part of this general program, a Congressional appropriation allowed the con¬struction of an electric-furnace, semicommercial, ingot-producing plant at Shasta Dam near Redding, Calif. The primary objectives of the pilot plant were to determine the costs and operating problems involved in the production of steel and ferrous alloys in which sponge iron was used as melting stock, and to determine the physical properties of the materials produced. The pilot-plant equipment and the results of sponge iron-melting tests in the basic lined, electric arc furnace have been reported in previous publications.3/4/

Jan 1, 1953

By C. S. Smith, L. H. Beck

KNOWLEDGE of the Cu-Zn constitution diagram was critically examined in 1944 by G. V. Ray-nor,1 who suggested the diagram reproduced in Fig. 1 as the best evaluation of available data. No pertinent work on the constitution has been published since that time, although a number of authors have discussed transformation kinetics and theory. Despite the large amount of work that has been done on the constitution of these industrially important and scientifically interesting alloys, minor uncertainties still exist. For example, it is still not possible to say definitely whether a two-phase region exists between the ordered and disordered forms of the 8 phase. A careful re-examination of the phase boundaries in this part of the diagram was therefore undertaken. Two methods were selected for the new investigation—quantitative metallography for the higher temperatures and precision lattice parameter measurement for lower temperatures. Because of the relatively narrow two-phase regions flanking the ß phase in these alloys, quantitative metallography is particularly suited for their examination, since the relative amounts of the two phases are very sensitive to their compositions. The method, however, is useless below about 350°C because of the inadequate resolution of the two constituents. Below 400°, however, the X-ray diffraction method is applicable, although it is of somewhat lower sensitivity in this system. The changes of composition that occur during quenching from above about 500°C entirely vitiate X-ray measurements at room temperature though they do not affect metallographic area measurements. The two methods overlap and supplement each other admirably. Both methods depend on the attainment of equilibrium composition of the two phases in a more or less intimate mixture and thus avoid the difficult problems of nucleation and long range diffusion involved in the conventional metallographic bracketing method. The alloys were melted from a master alloy made from re-electrolyzed cathode copper and Horsehead 99.99 pct Zn. Melting was done under a cover of either borax or charcoal and the alloys cast into a 7/8 in. sq graphite mold for the a-ß alloys or a 3/8 in. diam cylindrical graphite mold for the ß-? alloys. The a-ß alloys were rolled at 750°C to 5/8 in. sq; annealed for 24 hr at 800°C and quenched; then rolled and swaged at 200°C to 3/8 in. diam rods, annealed 24 hr at 200°C, quenched and cold rolled 2 pct reduction. This treatment was intended to obtain a small grain size and to produce many nuclei of the minor phase for growth on subsequent heat treatment. The unworkable ß-? alloys were given preliminary treatment by sealing in Vycor tubes in vacuum and annealing for 4 hr at 800°C followed by cooling in air. Samples of homogenized alloys were checked spectrographically for impurities, but the principal components were determined on samples subsequent to heat treatment. The impurities analyzed averaged approximately as follows: Ag, 0.0002 pct; Fe, 0.004; Si, 0.0008; Cd, 0.005; Mg, 0.0002; and Pb, 0.002. For metallography, samples of appropriate composition were cut into rods 5/8 in. long, sealed in pyrex tubes in vacuum and annealed for eight weeks at temperatures of 470°C and below, two weeks at 480°, 500°, and 600°C, and 4 hr at 700°C, followed by quenching in cold water. Temperatures were accurate to ±2°C. The cylinders were then machined to 8.7 mm diam and a slice weighing 1.5 g cut with a thin saw transversely from the center of each. This

Jan 1, 1953

Delivered by K. B. Gross at the First Ordinary Meeting of the Australasian Institute of Mining and Metallurgy, August 18th, 1952.Mr. President, Ladies and Gentlemen:Confronted with the task of reviewing the progress of Mount Isa Mines Limited, since the inception of the Company 28 years ago, I soon found that effective coverage was a task beyohd me, if I were to confine the address within the limits of time allowable. Faced with the alternative, a summary, that could only fail to -do justice to the subject, I turned elsewherl? for inspiration and found it in Chester Wilmot's book "The Struggle for Europe". Those of you who have read this masterly contribution to the literature of World War II will recall that he takes us, most dramatically, behind the scenes and we learn of the thoughts and ideas that were uppermost in the minds of both allied and enemy leaders at times when decision's that profoundly influenced the course of the war were taken. I felt I could safely follow this rather novel approach to my own problem. Strengthened by the realisation that the technical achievements of the Company have largely been covered over the years, and that the results of our labours are mainly here before you, I have attempted to liven up my modest canvas by going behind the scenes, and have sought to deal with ideas and the reasons for important decisions, rather. than to embark upon a purely descriptive essay.If then, you will bear with me, we shall skip back through the years to the days of struggle that our President's address has so aptly covered, and find that one man's ideas and faith stand out beyond all others. W. H. Corbould must always be credited with having founded the enterprise, for he correctly appraised the potential of the struggling prospect and foresaw what could be done, despite the handicaps of geography, climate and need for heavy expenditure.

Jan 1, 1953

By F. H. Wilson, E. W. Palmer

G. L. Bailey (British Non-Ferrous Metals Research Association, London, England)—I was glad to see this further work on the structure and properties of the Cu-Ni-Fe alloys of low nickel content in which we have been so interested in the United Kingdom since before the war." The authors' data on the variation in solubility of iron in both 5 and 10 pct Ni alloys with temperature is based on more detailed observations than we have made but is generally in line with our own work. The difficulty in these matters is in the identification of the structures obtained. The precipitation of the second phase which we presume to be the a' solid solution, richer in nickel and iron, from the a solution with which it is in equilibrium occurs in such a fine state of division that its resolution by ordinary micro-graphic methods is impossible in the early stages. We have published some electron micrographs which illustrate the effects observed more clearly but we agree with the authors when they say that dark staining characteristics when the alloys are subjected to sea-water corrosion are more sensitive in detecting the presence of the a' phase than is the microscope. After taking this point into consideration, however, I confess to some difficulty in understanding Fig. 4. I can only assume that the precipitates visible at such a low magnification as 150 diam in these relatively coarse forms are produced from iron-rich areas of the initial solid solution due to inadequate homogenization. If this is so I find it difficult to accept the authors' contention that such local variations in iron concentration as are capable of giving the heavy precipitates shown in Fig. 4 do not in fact materially affect the solvus surfaces of their equilibrium diagrams. I share the authors' enthusiasm about the resistance to corrosion of these alloys by seawater but I am not fully in agreement with them on the vexing question of the best iron content for these alloys. In Fig. 3 of ref. 8, we give many results showing that the resistance of these alloys to impingement attack in the Jet Test increases as the iron content rises to 2 pct. With higher iron contents pitting at shielded areas is likely to occur. Admittedly the addition of 0.75 pct Fe produces a large improvement in corrosion resistance compared with a pure 90/10 Cu-Ni alloy, but the further improvement on raising the iron to 2 pct is substantial. We recommend from 1.5 to 2 pct Fe as the desirable range from the point of view of corrosion resistance. While it is true that British practice generally uses a hard tube, the corrosion resistance of the 10 pct Ni alloys has in our work been little affected by the structural condition. Although the annealed alloys blacken in seawater, this effect seems to be superficial and not to be accompanied by any real decrease in

Jan 1, 1953

By J. E. Burke, A. M. Turkalo

IN 1923 Desch¹ pointed out that the grains in a metal which is anisotropic with respect to its thermal coefficient of expansion would contract differently upon cooling, and that the stresses developed might approximate the plastic strength of the metal. More recently Boas and Honeycombe2-5 studied the behavior of several metals upon thermal cycling and observed that the stresses developed in arlisotropic metals are great enough to produce slip lines in individual grains and a roughening of the specimen surface. This phenomenon they have named "thermal fatigue." The mechanism they propose involves essentially a kneading of the grains, the deformation being alternately in compression and tension in a given grain as the temperature is changed in one direction and then the other. The present work was undertaken to investigate the possibility that an additional mechanism might operate to produce plastic deformation during thermal cycling—a "thermal ratchet" that depends upon a combination of grain boundary flow to relax the stress that develops between differently oriented grains upon raising the temperature and transcrys-talline slip to relax the oppositely directed stress which develops on lowering the temperature. Thus, thermal cycling should produce a nonreversible distortion such that certain grains will change shape differently from their neighbors with a simultaneous displacement being produced at the grain boundary. Temperature Dependence of Grain Boundary and Grain Strength The critical resolved stress for the initiation of slip in metal grains is only mildly affected by temperature." For example, in cadmium it decreases from 0.15 to about 0.05 kg per sq mm when the temperature is increased from 20° to 458°K and further temperature increase causes little further decrease. On the other hand, the work of KG1 indicates that the grain boundaries behave in a viscous fashion that can be described8 by the expression: t = BVexp(Q/RT) [1] t is the shearing stress on the boundary; B, a constant; V, the flow rate at the boundary; Q, the activation energy for grain boundary flow; R, the gas law's constant; and T, the absolute temperature. Eq 1 indicates that the stress necessary to cause a given grain boundary flow rate, V, decreases rapidly with increasing temperature. The value of the constant B is such that at sufficiently low temperature and ordinary strain rates deformation will occur preferentially by slip rather than by grain boundary flow. There is considerable evidence to indicate Consider the bicrystal shown in Fig. 1. In grain 1 the slip plane lies 45 " to the boundary while in grain 2 the slip plane is 90" to the boundary. The coefficients of expansion of the grains in a direction parallel to the length of the crystal are a1 and a, with a, > a2 for the orientations shown. The sequence of events that can occur upon heating and cooling this specimen is illustrated schematically in Fig. 2. Initially there is assumed to be no stress in the specimen (A). Upon heating, grain 1 attempts to become longer than grain 2, but is constrained by grain 2. Thus grain 1 is loaded in compression and grain 2 is loaded in tension, and a shearing stress is present across the boundary (B). As the temperature is increased, the stress will build up, and finally grain 1 will be plastically deformed by slip, since the greater stress is resolved on its slip planes. Any further heating will result in more slip and the stress will remain constant until some temperature T* is reached where the stress can be relaxed by grain boundary flow.† At this relaxation temperature (C) a step will appear between grain 1 and grain 2. Further heating above T* will cause grain 1 to become relatively longer, but no stress will appear because the grain boundary is too weak to support the stress (D). Upon cooling again, at T* (E), the grain boundary will again be able to support a shearing stress, and upon cooling further, grain 1 will be loaded in tension and grain 2 in compression (F). When the decrease in temperature below T* is sufficient to impose the critical shear stress upon the slip plane of grain 1, it will be stretched by slip.

Jan 1, 1953