Search Documents

By A. M. Gaudin, J. G. Morrow

FLOTATION requires the existence of a definite contact angle. This contact angle, the surface tension of the solution, and adsorption at the solid- fluid interface are quantitatively related. Adsorption of dodecylammonium acetate on hematite was measured for a wide range of concentrations of reagent in solution. Similar measurements for quartz have already been made.1 Contact angle measurements were then made on polished surfaces of hematite and of quartz immersed in aqueous dodecylammonium acetate solutions, and a functional relationship was sought between adsorption density at the mineral-solution interface and the contact angle. Finally, the surface tension of the aqueous amine acetate solutions was measured. These data were combined to give an evaluation of the work of adhesion for the three-phase system.

Jan 12, 1954

By Frank J. Anderson

IN the cement region of the Lehigh Valley, a difference of 2 to 3 pct in CaCO3 can make or break a new quarry development, and experience of the Dragon Cement Co. has shown that values of calcium carbonate, as reported from churn drill samples, have been increased as much as 6 pct on the average when the same area was diamond drilled. This calcium carbonate increase consequently lowered the values for silica, iron, and alumina, and made these sections much more attractive. Since 1950, the Dragon Cement Co. Inc. has been engaged in extensive diamond drilling in the local limestone of the Northampton, Pa., region, known as the Jacksonburg formation, and in the Lebanon, Pa., region in the Annville limestone, both of Ordovician age.

Jan 12, 1954

By Harold M. Mooney

WHEN apparent resistivity data are taken with the symmetrical Wenner 4-electrode spread, a fixed center position is used and readings are taken for values of electrode separation. Basic data consist of apparent resistivity plotted against separation of adjacent electrodes. The interpreter attempts to infer geologic structure, such as the depth to discontinuities and the nature of subsurface earth materials. An earlier paper1 described methods for interpreting resistivity data. All of these involve a severe assumption, namely that the earth in the region of interest consists of horizontal layers, electrically homogeneous and isotropic. The actual earth never satisfies this assumption exactly and may deviate from it so much that none of the above methods can be applied. Attempts in three directions have been made to modify the assumption so that it approaches known geologic complexity more closely.

Jan 12, 1954

By H. F. Haller

COLUMBIA-SOUTHERN'S Barberton limestone mine, 8 miles southwest of Akron, Ohio, is a million-ton-per-year producer from a depth of over 2200 ft in a district where other underground mining at this depth is unknown. Mining extracts 46 of the top 51 ft from a formation of Devonian limestone discovered by drilling in the 1890's. The same drilling revealed extensive salt deposits below the lime- stone, which led to the location of the chemical plant at Barberton as a division of the Pittsburgh Plate Glass Co. in 1899. Soda ash was the principal product of the plant, and as production increased the demand for limestone increased. Columbia's first attempt to secure a reliable all-weather source of stone was the development of a quarry at Zanesville, Ohio, in 1919. Zanesville production eliminated some of the stock- piling required by the use of Michigan stone, avail- able only during the lake shipping season. Stone from some Zanesville horizons, however, was found to be more suitable for cement production than for soda ash, and rail transportation remained an important factor. As demand continued to increase, plans were made to develop the Barberton deposit.

Jan 12, 1954

By J. D. Price, W. M. Bertholf

THE central washing plant of the Colorado Fuel & Iron Corp. was first operated in 1918 to furnish coal for two 60-oven batteries of Koppers design. Prior to that time the coke for the blast furnaces had been secured from a number of beehive operations, some with their own washeries. The original washery had four Elmore jigs, which did not do as well as had been expected. In 1923 the jigs were taken out and replaced by Deister Plat-O tables, with various changes in auxiliary equipment. In 1936 the throughput of the plant was considerably increased by the installation of vibrating filters for recovery and drying of fine coal, thereby reducing a large recirculating load of fine coal which passed through the screens of the Carpenter driers.

Jan 12, 1954

By H. J. Ward

RUM Jungle uranium field lies in the subtropical portion of the Northern Territory on the Finniss River, East Branch. It takes its name from a railway siding about 2 ½ miles to the southwest and 52 miles from Darwin. The field can be reached from Darwin by a bituminized road. Monsoonal rains of the wet season, October to April, provide an annual rainfall of about 60 in. Vegetation is of the open forest type with denser tree growth along the watercourses and scattered throughout the area are isolated dense patches of jungle growth which are always found on ironstone cappings overlying limestones. The name, Rum Jungle, is thought to have been derived from this unusual occurrence of jungle growth. The wet season prevents the movement of motor vehicles and personnel. It is not until March, when the grass which ranges up to 15 ft in height is burned and the alluvial flats dry out, that field work can be undertaken.

Jan 12, 1954

By Edward Thomas

ROCK bolting, third great change in postwar underground mining, is inseparably tied to the other two changes: better drilling and mechanized mining. Mechanized mining provided the impetus, when conventional supports restricted maneuver-ability of equipment-while carbide-tipped bits lent the means of drilling required holes cheaply. With the need and the tools at hand development snow- balled. In just six years, from January 1948 to January 1954, some 800 mines adopted bolting for systematic support, and over 100 of these mines now use rock bolts exclusively. Simultaneously, foreign mines have adopted the idea, but to a lesser extent. What held back this major change? The concept of fastening loose material to unbroken and apparently solid material is probably as old as mining itself, and sporadic use has been reported from virtually every mining region in the world. But falls of rock have always been the greatest source of both fatal and nonfatal accidents in underground mining and miners have understandable reluctance to work under roof or back material if they even suspect that it might be hanging like a "sword of Damocles" -supported only by a thin bolt.

Jan 11, 1954

By Clinton L. Miller

MINING operations have been carried on in the immediate area of the Elizabeth mine during periods of high copper prices since 1793, when copperas and vermillion were first won from the outcrop. Present operations started in 1942 as a war baby. Since then production has totaled 1.7 million tons of 1.8 pct Cu ore. Elizabeth mining operations are on a pyrrhotite- chalcopyrite orebody contained in a gently plunging amphibolite syncline. The oreshoot varies in width from 10 to 40 ft, and in the area under consideration is about 150 ft in vertical extent, and more than 1000 ft long. Surface pits or cuts have been worked in three areas along the outcrop, with one pit just completed and a second in full production. Present production is 24,000 tons per month, of which 6000 to 7000 tons is trucked from the open pit.

Jan 11, 1954

By G. Donald Emigh

WESTERN phosphate resources which lie in Ida- ho, Montana, Utah, and Wyoming, have seen great expansion of activity in recent years. Growth has been two-pronged: expansion in fertilizer use, and since 1949, into the elemental phosphorous industry. Elemental phosphorous, produced in the electric furnace, goes largely into chemical making. Phosphate ore was first recognized in the West about 1889. Production started in 1906, and for many years consisted of underground operations by small companies operating sporadically. In 1920 Anaconda Copper Mining Co. opened the underground Conda mine near Soda Springs in southeastern Idaho, and has maintained and increased its operations since then. About 1930 Montana Phosphate Products Co. began underground mining in Montana and has remained a steady producer. In 1945 San Francisco Chemical Co., one of the oldest companies in the western field, initiated strip mining at the Waterloo mine near Montpelier, Idaho, and later at Leefe mine near Sage Junction, Wyo. In1946 J. R. Simplot Co. began open pit mining at Gay mine near Fort Hall, Idaho. In 1950 Victor Chemical Works began underground development work in the area of Maiden Rock, south of Butte, Mont.: and has since mined there. Monsanto Chemical Co. began open pit mining near Soda Springs, Idaho, in 1951.

Jan 11, 1954

By Patrick H. O’Neill

FUNDAMENTALLY a dredge designed for operating under arctic conditions and particularly when the temperature is below freezing is not greatly different than one for use in more moderate climates. Because of the accumulation of ice it is necessary to design suspension units to carry an increased weight when ice forms on the digging ladder or stacker. Winch room and house must be made with double walls and insulated. The dredge must be heated either by steam or by circulating warm air electrically heated. The stacker must be covered and heated to avoid having the drive units frozen tight. Actually the worst trouble that might develop in a stacker, because of cold weather, is the freezing of spilled material and ice accumulation on the head pulley and the underside of the belt. For this reason, stackers are completely enclosed and the pan kept open to get rid of any spilled material and to prevent overloading. Since the stacker is the most vulnerable place on a dredge in cold weather, heat is turned on there long before it is necessary any other place on the dredge. The principal points of interest in' connection with dredging, under subfreezing conditions, concern the preparation of the ground being dredged and the frozen ponds. In the interior of Alaska, and also in the Yukon territory of Canada, most of the gold bearing gravel deposits are permanently frozen and they are also covered by variable thicknesses of fine grained sediment, locally called muck. The better pay areas in this frozen ground have generally been worked by the earlier miners who sank shafts to bedrock in the frozen ground, then drifted in four directions and dug out the areas between the drifts as they re- treated toward the shaft. They thawed only the area they were excavating, doing so with steam from wood-fired boilers, and hoisted pay gravel to the surface for subsequent washing.

Jan 11, 1954

By Kenyon E. Richard, James H. Courtright

SILVER Bell is situated 35 airline miles northwest of Tucson, Ariz., in a small, rugged range rising above the extensive alluvial plains of this desert region. Its geographical relation to other porphyry copper deposits of the Southwest is shown on the inset map in the lower left corner of Fig. 1. The climate is semi-arid. Altitudes range within 2000 and 4000 ft. Opening of the Boot mine, later known as the Mammoth, in 1865 was the first event of note in the district's history. Oxidized copper ores containing minor silver-lead values were mined from replacement deposits in garnetized limestone and treated in local smelters. Copper production had approached 45 million pounds by 1909 when the disseminated copper possibilities in igneous rocks were recognized. Extensive churn drill exploration carried out during the next three years resulted in partial de- lineation of two copper sulphide deposits, the Oxide and El Tiro. Although the then submarginal tenor discouraged exploitation of these disseminated deposits, selective mining of orebodies in the sedimentary rocks continued intermittently until 1930, providing a production total of about 100 million pounds of copper.

Jan 11, 1954

By B. E. Grant

There are several exceptions from the practical operating viewpoint that might be taken with the paper. The author recommends using a "curve" in plotting safety factors of ropes and suggests that the U. S. Bureau of Mines change its present "step curve" method to the "curve" method. From an engineering theoretical point of view that is possible, but from a practical standpoint it is not possible. Rope manufacturers fabricate their ropes in diameter gradients of 1/16 in. to 1/4 in. which automatically sets up a step pattern gradient. If ropes were manufactured in the diameter gradients of 1/1000 of an inch or thereabouts, the curve method could be used. Also, from a practical standpoint, if an operator is to hoist from a depth of 4000 ft, for example, he will determine the size of the rope necessary for that depth, and it is only natural that he will have safety factor to spare at lesser depths, and in plotting this excess capacity the natural end result is a curve. The U. S. Bureau of Mines tables are set up so that the operator will know what size rope at the required safety factor he will need at his maximum depth. He is not concerned with lesser depths. W. A. Boyer (author's reply)-Mr. Grant states, "Rope manufacturers fabricate their ropes in diameter gradients of 1/16" to 1/4" which automatically sets up a step pattern gradient." There is no connection or relationship between the "size" pattern gradient and the present "factor of safety" step pattern gradient. The inherent factor of safety values for any particular size of rope with a given connected load when plotted for various depths is a curve, and with modern rope material and construction the inherent factor of safety curve is quite far removed from the present recommended factor of safety step curve. This is shown quite clearly in Figs. 3 and 4 of my paper.

Jan 11, 1954

By William H. Love

ATLAS shaft was sunk to explore at depth a portion of the eastern end of the dry belt, or silver belt, of the Coeur d’Alene mining district. The Atlas mine is a mile east of Mullan and is on the south side of the Osburn fault. Equal partners in the venture are Hecla Mining Co., Newmont Mining Co., New Jersey Zinc Co. and Atlas Mining Co., the financing being equally shared by Hecla, Newmont, and New Jersey Zinc. As outlined the project had as its goal deep exploration of prominent structures developed in the Atlas in upper levels. Plans called for deepening the shaft from the 800 level to the 2400 level with subsequent drifting, crosscutting, and diamond drilling on the 2400.

Jan 11, 1954

By Owen F. Jensen

CONSTRUCTION of a ground-water supply includes many operations, which do not end with completion of facilities. Evaluations must be made of the quality of water in various areas and the history of production. Following an analysis of geologic, hydrologic, and chemical data there must be an exploratory drilling program and a study of resulting information. When the well is completed a continuous survey of operating records and basic data is necessary, since designs for future wells are varied as more data becomes available for those already completed. As the following discussion must be limited to a single undertaking, the customary procedure will be outlined for development and construction of a ground-water supply in which more than three wells are involved. Parts of this procedure are applicable for all ground-water supplies.

Jan 11, 1954

By Harry Bapty

LONGHOLE drilling with a heavy type percussion Leyner drill, jointed steel rods, and a tungsten carbide insert bit was investigated while drilling and working a quartz barite brecciated rock. Procedure and practice were developed and its suitability for tackling pillar and sill recovery proven and extended to regular stoping at Torbrit. Torbrit, as the name implies, is a contraction of the Toric property and the Britannia Mining & Smelting Co. Ltd., the former owners. This silver property, with minor amounts of lead, zinc, and rarer sulphides of little or no economic value, was discovered in 1916 from an outcrop in the Kitsault River, 18 miles north of Alice Arm Post Office, in the Portland Canal Mining District, B. C.

Jan 11, 1954

By W. A. Boyer

HOISTS for metal mines are seldom designed for H one particular depth. They are intended for an ultimate load and depth with a given speed but are first used to hoist from a shallower depth, gradually working to the ultimate as development progresses. Sometimes the mine is not worked on the upper levels because of the kind and grade of ore, the mining of which depends on market conditions. In this case the hoist may be used in the same working shift to lift ore, for example, from the 1200 and the 4400-ft level. This means that the safety factor of the rope should be considered not only when it hoists from the greatest depth, but also when it hoists from the upper levels. According to present safety factor standards, a hoisting rope can have ample safety margin when hoisting from the lower or lowest level and still be shy of sufficient safety margin when hoisting from the upper levels. This will be shown by curves presented in this paper.

Jan 10, 1954

By John V. Hamme

ONE of Tungsten Mining Corp.'s Vance County, N. C., mill near Henderson was the installation of a new crushing plant with a capacity of 45 to 50 tph. During 1953 the milling rate was jumped from 650 tons to 800 tpd simply by expanding existing facilities, eliminating bottlenecks, and making changes in the existing and new circuits. Previous expansions in 1951 and 1952 raised mill capacity from 300 tons to 650 tpd. In its latest move, Tungsten Mining decided that expansion of existing facilities would be more economical than building that normal production was uninterrupted. For the engineering and design of the new crushing plant and mill expansion the services of the Southwestern Engineering Co., Los Angeles, were obtained. The Southeastern Construction Co., Charlotte, N. C., carried out construction, alterations to existing facilities, and the installation of equipment

Jan 10, 1954

By T. H. Janes

NATURAL abrasives of some type are found in all countries of the world. In order of their hardness the principal natural abrasives are diamond, corundum, emery, and garnet, which are termed high grade, and the various forms of silica, including pumice, pumicite, ground feldspar, china clay and, most important, sandstone. The properties qualifying materials for use as abrasives are hardness, toughness, grain shape and size, character of fracture, and purity or uniformity. For manufacture of bonded grain abrasives such as grinding wheels, the stability of the abrasive and its bonding characteristics are also important. No single property is paramount for all uses. Extreme hardness and toughness are needed for some applications, as in diamonds for drill bits, while for other purposes the capacity of the abrasive to break down slowly under use and to develop fresh cutting edges is of greatest importance, as with garnet for sandpaper. In dentifrices, soaps, and metal polishes, of course, hardness and toughness are objectionable.

Jan 10, 1954

By J. Visman

FOR more than 25 years evaluations of coal cleaning units have appeared in many publications, and during this time considerable progress has been made in developing the theory and techniques of calculating washery results. A variety of characteristics have been defined over the years, many receiving general recognition during the first post-war Coal Preparation Conference in Paris in 1950. Coal preparation has become a science, and the approach to preparation problems is being revolutionized. Formerly, for example, if a coal operator wanted to know the performance of a given cleaning unit for a particular grade of his run-of-mine, he either shipped a carload to the manufacturer for a test run or relied on a report of a test carried out on a coal similar to the one he intended to clean. In modern practice the expensive, time-consuming test work generally can be avoided if the washability curves of the coal in question and the error curve of the cleaner are known. Normally a guarantee can be given on the strength of this information. General acceptance of modern standards has thus reduced the need for pilot-scale models of existing types of coal cleaners. Needless to say, the method requires exhaustive and accurate information on the cleaning unit and on all the additional circumstances affecting its results, in- formation that ultimately can be secured only from actual tests made in the laboratory or in the washery.

Jan 10, 1954

By C. H. Benedict

1. Shaking Tables 2. Fine Grinding 3. Hydraulic Classification 4. Mechanical Thickeners 5. Flotation ENTERING the profession of minerals beneficiation (it was plain garden variety "ore dressing" . in those days) I was fortunate that at that time the first major innovation in modern ore dressing practice was being introduced. I refer to the Wilfley table. You youngsters that came into the game only 30 years ago or even more recently, with flotation machines and reagents as your very ready tool in time of trouble, do not realize what the invention of the Wilfley table meant to us. We had but one physical property of ores to reckon with-specific gravity- and when there was but little difference in specific gravity between the mineral and the gangue, we were in trouble. The jig and the revolving table were our only mechanical equipment for recovering values and so that we might make even a reasonably satisfactory extraction, we had to classify and reclassify, and jig and rejig, and worry about the laws and advantages of free settling vs hindered settling and just tire the minerals out.

Jan 10, 1954