Search Documents

By S. Weinig, E. S. Machlin

THE mechanism of the martensitic transformation has been the subject of a remarkable number of papers in recent years.' Because the task of evaluating all the available theories is a formidable one, the authors will confine themselves merely to the presentation of results of an experimental investigation of the habit orientation, lattice relations, magnitude and direction of average transformation shear strain, and orientation of subband markings for a single variant of the possible habit systems in an 11 pct Mo-Ti alloy. It is hoped that these data will assist in the establishment of a rigorous theory for the mechanism of the martensitic transformation. Experimental Procedure Specimen Preparation: A sample, approximately 1/2 x 1/4 x 1/4 in., was cut from a double arc-melted ingot composed of commercial-process A titanium and high purity molybdenum (nominally, 11 pct Mo). It was capsuled in evacuated Vycor at 10.-3 mm Hg subsequent to a double argon wash and homogenized for 48 hr at 1100°C. After a direct quench into H2O at room temperature, a large-grained specimen resulted, which, by X-ray diffraction and metallographic means, was subsequently shown to be in the body-centered-cubic phase, ß. Two adjacent, approximately perpendicular faces were polished and the ends of the specimen were ground parallel in a V-block. Fiducial lines were inscribed at 45" to the common edge of the polished surfaces in order that they would be perpendicular to the habit traces of the subsequently formed a plates.2 The specimen was then compressed between the ground ends in a Buehler press to stress induce the transformation ß to a'. Experimental Measurements: The habit-plane orientation, the orientation of subband markings, the orientation relation between the parent ß and the product a', and the transformation strain for the same plate were determined. To further establish the nature of the subbands, one surface was repol-ished and etched. The bands in the a' were still visible and were found to be optically anisotropic under polarized light. Back-reflection Laue patterns were obtained from the ß matrix and from a region comprising both a' plates and adjacent ß matrix (a Cu target was used). By superposition of the two X-ray diffraction patterns, it was possible to obtain a tentative orientation relationship between the two phases. This result was confirmed by a pattern taken after the specimen was rotated to make the basal-plane pole of the hexagonal a' phase strike the film. This necessitated cutting the specimen to expose the a' plate in the new position relative to the X-ray beam. Analysis of Experimental Measurements On the basis of the aforementioned X-ray patterns, the orientation between parent and product

Jan 1, 1955

By W. O. Philbrook

An engineering analysis indicates that the coke rate in present blast-furnace practice is set not by chemical or thermal needs but to give adequate charge permeability for economical driving rates. An equation showing interrelations among pressure drop, gas flow, and charge characteristics has been derived. Flooding conditions and the location of the fusion zone are discussed. Maximum ore size is probably limited by chemical re-ducibility rather than by heat transfer. THE intention of this paper is to show that the ].imitations on the production rate and coke requirement of the iron blast furnace are not primarily chemical or thermal in nature but are related to characteristics of the burden and operation that govern gas flow, heat transfer, and stock movement. A semiquantitative analysis will be developed in terms of standard engineering principles to give a useful picture of the relative importance of physical and mechanical factors in contrast with the chemical features of the process that are more commonly emphasized. Most of the details of calculation have been omitted in the interest of brevity and to avoid submerging the rnain points in a sea of arithmetic. Numerical values have been arrived at by objective methods from reported operating data or by reasonable estimates of material properties where exact data are lacking and then tested to see how well they fit practice, rather than by working backward to find what assumptions are needed to give the desired answers. The analysis is oversimplified in many ways because exact engineering relations have not yet been studied for bed distributions as complex as are known to exist in the blast-furnace stock column. One objective of this paper is to show that the blast furnace, in spite of its complexity, can be at- tacked by engineering methods in the hope that this viewpoint will stimulate the kind of research needed for a more exact treatment. The basic ideas and many of the conclusions presented are qualitatively well known. A careful literature survey to credit the source of all observations not original to the author would indeed be voluminous, and such has not been attempted. T. L. Joseph's Howe Memorial Lecture' gives an excellent background of what is known about the internal workings of a blast furnace. Other important reference works or sources of specific information will be noted. It is hoped that the present paper will contribute something new, in method of attack and interpretation, that will aid in a clearer understanding of how to operate the blast furnace to best advantage. Factors Limiting Production and Coke Rates The rate of combustion of coke in a blast furnace, as in any fuel bed, is exactly proportional to the rate at which air is supplied. It is axiomatic, then, that the production rate of a furnace is limited by the rate at which it will take wind, i.e., burn coke, and the amount of coke that must be burned at the tuyeres to make a ton of iron of suitable composition. These two possible limiting factors will be considered briefly in the order mentioned. One common restriction on wind rate is flue-dust production. Since the volume of top gas is nearly proportional to the blast volume (by a factor of about 1.35 on a dry basis), an increased wind rate causes a correspondingly increased linear velocity of top gas in the throat of the furnace. The higher

Jan 1, 1955

By T. R. A. Davey

IN 1947 the author became interested in the fundamental aspects of the desilverizing of lead by zinc, conducted some experimental work, and searched the technical literature for all available fundamental data. Since then a revival of interest in the subject in Europe resulted in the appearance of quite a number of papers. It became evident that it would be more profitable to collect together and examine thoroughly the results of various workers, than to attempt to duplicate the experimental determinations. There are many inconsistencies in the various publications, and it is opportune to review at this time the present status of knowledge on the Ag-Pb-Zn system. There is also a need for a clear description, in fundamental terms, of the various desilverizing procedures. This paper is presented in four sections: 1—There is an historical review of the origins of the Parkes process, of the results of many attempts to find a satisfactory fundamental explanation for the phenomena, and of the modifications proposed to date. 2—A diagram of the Ag-Pb-Zn system is presented. This is believed to be free of obvious inconsistencies or theoretical impossibilities, although thermodynamic analysis subsequently may reveal errors. 3—The fundamental bases of the various desilverizing procedures, which have been used up to the present day, are described; and a new method is suggested for desilverizing a continuous flow of softened bullion in which the bullion is stirred at a low temperature in two stages producing desilverized lead at least as low in silver as that from the Williams continuous process and a crust which, on liquation, yields a very high-silver Ag-Zn alloy. 4—A suggestion is made for the revival of de-golding practice, following a recently published account which does not seem to have attracted the attention it deserves. The terms "eutectic trough" and "peritectic fold" as used in this paper are synonymous with "line of binary eutectic crystallization" and "line of binary peritectic crystallization" as used by Masing.' The German literature on ternary and higher systems is rather extensive and a fairly general system of nomenclature has arisen, whereas in English usage the corresponding terms are not as well established. For this reason the meanings of terms used in this paper, together with the equivalent German terms, are given as follows: 1—Eutectic trough—eutektische rinne: line at which a liquid precipitates two solids S1 and S2 simultaneously. If the composition of a liquid which is cooling reaches this line, it then follows the course of this line until a eutectic point is reached, or until all the liquid is exhausted. The tangent to the eutec-tic trough cuts the line joining S1S2. 2—Peritectic fold—peritektische rinne: line at which a solid S1 and a liquid L transform into another solid S2. If the composition of a liquid which is precipitating S1 reaches the line, on further cooling only S2 is precipitated. The liquid composition moves from one phase region (L + S1) into the other (L + S2), and does not follow the course of the boundary. The tangent to the peritectic fold cuts the line S1S2 produced nearer S,. 3—Liquid miscibility gap, or conjugate solution region—mischungslucke: the region within which two liquid phases coexist in equilibrium over a certain range of temperature. A system whose composition is represented by a point in this region comprises one liquid at high temperature; then as the temperature is progressively reduced, two liquids, one liquid and one solid, one liquid and two solids, and finally three solids. 4—Liquid miscibility gap boundary—begrenzung der flussigen mischungsliicke: the line along which the surface of the miscibility gap dome, considered as a solid model, intersects the surrounding liquidus surfaces. 5—Tie lines—konoden: lines joining points representing the compositions of two liquids, a liquid and a solid, or two solids, in equilibrium. In binary systems the only tie lines customarily drawn are those through invariant points, e.g., through the eutectics of the Pb-Zn and Ag-Pb systems, or the various peritectics of the Ag-Zn system, as in Figs. 1 to 3. In ternary systems it is desirable to draw sufficient tie lines to indicate the slopes of all possible tie lines. 6—Ternary eutectic point—ternares eutektikum: point at which liquid transforms isothermally to three solids, S1, S2, and S Such a point can lie only within the triangle 7—Invariant peritectic (transformation) point— nonvariante peritektische umsetzungspunkt: (a) — On the miscibility gap boundary, the point at which two liquids and two solids react isothermally so that L, + S, + L, + S2. (b)—On the eutectic trough, the point at which a liquid and three solids react iso-thermally so that L + S, + S2 + S3. Such a point must lie on that side of the line joining S,S which is further from S,. (c)—A further possibility, not found in this ternary system, is that the point is at the intersection of two peritectic folds when the reaction concerned is L + S, + S, + S Historical Introduction Karsten discovered in 1842 that silver and gold may be separated from lead by the addition of zinc.2 Ten years later Parkes used this fact to develop the well known desilverizing process which bears his

Jan 1, 1955

Local conditions at Hatches Creek are described, together with the mineralogy, mining and treatment of tungsten ores, with particular reference to procedures adopted by Pimer Mines, N.L.The Hatches Creek tungsten field covers an area of about 20 square miles in: Central Australia; 285 miles' N.E. of Alice Springs. Access is by rail to Alice Springs, then by 200 miles of bitumen highway to Barlo Creek and 8,5, miles of bush track to the field. Passengers can also reach the mines by... A semi-desert climate prevails Rain; generally in the form of thunderstorms falls in the summer months: December to March. Average annual rainfall is approximately 15 inches but there is great variation from year to year, occasional droughts being followed by torrential downpours. Vegetation is sparse except in the wide creek beds. Surface water occurs in rock holes some of which, spaced miles apart, carry permanent water...

Jan 1, 1955

By Robert R. Walden, LeMont West

K ENTUCKY'S first acid-grade fluorspar flotation Kmill, shown in Fig. 1, was placed in operation Aug. 1, 1952, by the Pennsylvania Salt Manufacturing Co. at Mexico, Ky. During 1951 a critical shortage of acid-grade fluorspar developed and it became necessary for the company to produce part of its fluorspar requirements. In 1951 the company purchased the Crider and Lennen metallurgical fluorspar mill and an adjacent stockpile of tailing at Mexico, Ky. The tailing, assaying about 26 pct calcium fluoride, originated from log washer and jig mill concentrators in the area. As the mill did not have a fluorspar dryer or convenient rail facilities, the company leased the Burleson concentrator at Marion, Ky., where these facilities were available. At Marion, Ky., on the Illinois Central Railroad, dry acid-grade fluorspar is transported direct to the company's Calvert City, Ky., hydrofluoric acid plant. The Mexico flotation plant was reconditioned and designed to produce acid-grade fluorspar from the jig tailing stockpile. The new plant flowsheet is shown in Fig. 2. The ore feed, old tailing, which contains 10 pct of waste rock and coarse gravel assaying approximately 8 pct CaF,, is bound together by sticky clay

Jan 1, 1955

By L. H. Banning

In the fall of 1953 the Philippine Bureau of Mines, under a Foreign Operations Administration Technical Assistance (FOA-TA) program, began a systematic investigation of the nickel content of the well-known Surigao laterite areas, on the island of Nonoc northeast of Mindanao, to determine the occurrence, distribution, and grade of nickel contained in the laterite and in the subjacent serpentine. At the same time, a technical review of the possibility of producing commercial ferronickel from the nickeliferous materials in the Philippine Islands was made, and a smelting process was suggested. The proposed process would be similar to that developed by the Federal Bureau of Mines for the reduction of the nickeliferous serpentine occurring in the Nickel Mountain ?deposit at Riddle, Oreg. The potential avail-ability of electric power from the Maria Cristina facilities at 3 mils per kw.-hr. would enhance the economic possibility of this program. Development of an economically feasible process for recovering nickel from the nickeliferous serpentines and laterites should lead to the establishment of a new industry in the Philippines, to the development of a source of nickel in the Far East, of which at present there is none, and to partial solution of the problem of supplying the free world with nickel. Enough preliminary reconnaissance had been completed by early 1954 to permit sampling of the deposit for metallurgical investigations. The FOA then requested the Federal Bureau of Mines Northwest Electrodevelopment Laboratory, Albany, Oreg., to conduct preliminary electric smelting studies on nickeliferous serpentine and laterite samples.

Jan 1, 1955

By W. B. Agocs

"AbstractThe airborne magnetometer data of the Marmora iron ore deposit at Marmora, Ontario, have been used as an example to show the mapped results obtained by the use of line spacings of from 1 mile to 14 mile. The maps are illustrative of the results which could be obtained from such line spacings for any type of geophysical survey, and they show the probability of 'missing' a feature of economic value if the line spacing is too coarse.The probability equations are given for the crossing of randomly oriented features whose maximum dimension is less than the spacing of the control lines for circular, elongate, and rectangular outlines. The equations are P = D/S; P = 2L/S; P = 2(L+W)/,.S; P = A/,.S; P = (2L(S+T)-L2),.ST; and P (D(S+T-,.D)) ST, respectively; where P is the probability; D is the diameter; L is the length; W is the width; and S and T are line spacings.IntroductionTHE EFFECT of station spacing, and the effect of the distance between the plane of observation and the plane of the source of the potential field anomalies, have been studied by geophysicists in the past.The purpose of this paper, however, is to illustrate the effect of line spacing •on the resultant mapped magnetic anomaly for a known magnetite mass, and to present the elementary probability equations for determining the optimum control spacing for detecting a particular type of feature. The effect of line spacing which is illustrated by the magnetic maps presented herewith would be comparable to results which would be obtained by any geophysical survey, since the contours between lines are of necessity interpolated."

Jan 1, 1955

By Ralph V. Higgins

This paper concerns the magnitude of the amount of supersaturation that occurs in an underground reservoir during the flow of oil and gas to wells and to the amount of undersaturation that occurs during repres-suring of an oil reservoir where some effective permeability to gas exists. The study is based on earlier laboratory findings of other investigators on the rate of diffusion of gas in oil as a function of the depth of oil. Utilizing these relationships and the principles of reservoir mechanics, a quantitative estimate of undersaturation and super-saturation was calculated. The results showed that the diffusion of the gas is rapid enough that for all practical purposes no supersaturation exists during the flow of oil to wells or undersaturation during repressuring in reservoir sands having some effective permeability to gas. The reason diffusion of the gas virtually keeps the oil saturated is the long time required in radial flow for oil to reach the well and the slow rate at which pressure in reservoirs is increased during repressuring. INTRODUCTION Knowledge of the phase relationships during flow of gas and oil in an underground reservoir is essential to operating the reservoir in the most efficient manner. In material-balance calculations and in fluid-flow studies, the oil is assumed to contain all the gas that it will dissolve at given temperature and pressure. Pressure-volume-temperature relationships are normally obtained in the laboratory using "bottom-hole" or combined samples of the reservoir fluids. In such laboratory determinations equilibrium is obtained between the oil and gas in the pressure cells by mechanical agitation. During the flow of oil and gas in reservoirs, however, no comparable agitation occurs to mix thoroughly these fluids to aid in effecting equilibrium between the two phases. During repressuring of a partly depleted underground reservoir, the gas is usually injected into the reservoir faster than the oil can absorb it; consequently, the oil is undersaturated. On the other hand, as the oil flows through the reservoir to the wells during producing operations the pressure decreases faster than the gas in solution can diffuse through the oil to the gas phase. The oil therefore is supersaturated with gas. Where the oil is undersaturated, gas diffuses away from the gas-oil interface, and where it is supersaturated the gas diffuses toward the interface. In either case the gas moves from a higher to a lower saturation. This report contains the results of a study of the factors influencing the degree of nonequilibrium of the phase relations of oil and gas in porous mediums during the flow of oil through reservoirs to wells and also during the injection of gas into partially depleted sands. Data from an underground reservoir are presented and the degree of supersaturation during the flow of the oil through the reservoir to the well is approximated. Also data from another reservoir are used and the degree of undersaturation during the repressuring operation is calculated. In addition, the flow rates of oil in laboratory experiments and in underground reservoirs are compared, as data from the laboratory are often used to interpret events in the reservoir, and the rates of flow influence appreciably the degree of nonequilibrium. Much of the contents of this report was prepared in 1943; but, because of other activities during and since the war, the manuscript was left untouched until 1952, when it was decided to include an estimate of the amount of undersaturation during repressuring as well as supersaturation during flow.

Jan 1, 1955

By P. Stark, B. S. Lement

ACCORDING to Hanemann1 the hardness of retained austenite in a 1.7 pct C steel is increased by subsequent tempering. He reported that the hardness of this constituent increases only slightly on tempering to 300°F, rises more rapidly above this temperature, and attains the same value as the tempered martensite present in steel at approximately 480°F. The variation of hardness of both retained austenite and martensite with tempering temperature as obtained by Hanemann1 is shown in Fig. 1. Hanemann attributes the increase in hardness of the retained austenite essentially to continued formation of fine needles of martensite on tempering. Although he did not explain the actual mechanism involved, work hardening of retained austenite by the plastic deformation associated with such martensite formation appeared to be a possibility. Recently Lement, Averbach, and Cohen2 reported the existence of subgrains, about l000Å in diameter, in retained austenite and suggested that they may be delineated by a subboundary carbide. This raised the possibility that carbide precipitation might be responsible for the hardening reported by Hanemann. In view of these conflicting possibilities, an investigation" was carried out on a high purity, Fe-C alloy containing 1.7 pct C in order to clarify the nature of the phenomenon involved in the reported hardening of retained austenite. This investigation involved correlation of changes in microhardness and microstructure of the austenite as a result of tempering. Microhardness tests were made with a Tukon tester using a 25 gram load and a Vickers diamond. It was found that two groups of austenite hardness values were obtained after tempering at a series of temperatures up to 450°F, which was the highest temperature at which retained austenite regions could be identified microscopically. One group represents a high hardness level which in-

Jan 1, 1955

By Anderson C. G

The design of crawler-mounted conveyor belts installed for the handling of brown coal in open cuts is described.INTRODUCTIONThe State Electricity Commission of Victoria operates two brown coal open cuts at Yallourn, Victoria. The larger of these cuts produces n million tons per year of brown coal containing 67 per cent. moisture, and the smaller, at Yallourn North, produces 1-1 million tons of coal, with a moisture content of 50 per cent. A further open cut at Morwell with projected output of 9-10 million tons per year is in the course of development. In the larger Yallourn open cut coal is excavated by means of conventional bucket chain and bucket wheel dredgers and transport is by electric locomotives and saddle bottom trucks running on 90 cm. gauge railway tracks. At Yallourn North, coal until recently has been largely won by 3i and 5 cu. yd. electric shovels and transported by large diesel-enginedmotor trucks. The difficulty of keeping these trucks in operation during the winter periods owing to the v.ery wet conditions and the high cost of maintenance of these vehicles led to the introduction of a moving face conveyor system.EXISTING CONVEYOR INSTALLATION AT YALLOURN NORTHA conveyor system employing a 36-in. belt running at a speed of 400 ft. per minute and having a nominal capacity of 425 tons per hour with 50-h.p. drive units, was selected as appropriate for the output of the open cut. The conveyor structure adopted was a standard type as used in under...

Jan 1, 1955

By F. Kurata, A. F. Bertuzzi, P. C. Davis, T. L. Gore

The phase and volumetric properties of 10 very volatile mixtures are presented for temperatures from — 200°F to above the critical points. These mixtures consisted of natural gases and of mixtures of natural gases with methane and nitrogen. Existing correlations of compressibility factors have been extended to apply to these mixtures. Existing correlations of critical pressures and temperatures do not apply to these mixtures. Methods have been developed for estimating critical temperatures of these mixtures to ± 4°F and critical pressures to 2 5 per cent. These methods apply to other volatile and very volatile mixtures. The results of this work are particularly applicable to the separation of nitrogen from hydrocarbons by low-temperature distillation. INTRODUCTION Knowledge of the low-temperature phase and volumetric properties of natural gases and of other mixtures of the light hydrocarbons is becoming increasingly important as interest in low-temperature separation processes increases. Low-temperature distillation has been used to separate ethane and ethylene from natural gas and from refinery gases for petrochemical uses. Removal of nitrogen from natural gas by low-temperature distillation has been proposed 7,20 as a means of increasing the capacity of existing gas transmission lines and of improving the marketability of the gas. Further application of low-temperature separation processes has been retarded by lack of data on the phase and volumetric behavior of mixtures at low-temperatures and at high pressures. This paper presents the results of determination of the phase and volumetric properties of 10 very volatile mixtures at temperatures from - 200 °F to above the critical point. These mixtures consisted of natural gases with methane and nitrogen. Generalized methods are presented for estimating the critical temperatures, critical pressures, and the densities of such mixtures. EXPERIMENTAL APPARATUS AND PROCEDURES The apparatus and the experimental procedures have been described in an earlier paper13. The method consists of displacing the mixture from a reservoir which is maintained at constant temperature and pressure into an agitated glass equilibrium cell which is maintained at constant temperature. The liquid level within the glass equilibrium cell was visually observed, and the pressure was measured to within & 3 psi with a calibrated Bourdon gage. COMPOSITIONS OF MIXTURES STUDIED The compositions of the mixtures studied are summarized in Table 1. The measured properties included in Table 1 will be discussed later in this paper. The sources of these gases are described below: Gas "A-1'' was obtained from the Phillips Petroleum Co. Its composition was reported in connection with earlier work." The properties of this gas were reported in an earlier paper.13 Gases "A-2, A-3, A-4" were prepared by mixing nitrogen with gas "A-1." Gas "AB-1" was prepared by mixing methane with gas "A-1." The properties of this gas were reported in an earlier paper.'" Gases "AB-2" and "AB-3" were prepared by mixing nitrogen with gas "AB-1." Gas "B" was obtained by W. W. Bodle of J, F. Pritchard & Co. from the primary separator of a well in western Kansas. Gas "C" was obtained from a Cities Service Co. pipeline at Lawrence, Kans. Gas "D" was prepared by mixing gas "AB" with gas "C."

Jan 1, 1955

By S. H. Ash

NINE-TENTHS of the total anthracite deposits of North America are in Pennsylvania. Corrosion of pumping equipment by acid mine waters has been experienced at tremendous cost by mining companies in the anthracite region of Pennsylvania, for many years in many ways. The design and specifications of the large centrifugal pumps as provided in the proposed mine-drainage system (7-35, 45, 46, 48, 54, 64, 70, 71)° make it imperative that a metal or alloy be recommended that has the highest corrosion resistance and, at the same time, acceptable properties suitable for general workability (welding and machining). This report presents data on the corrosive and erosive effects of acid mine waters in the anthracite region on metals and alloys for pumping equipment and drainage facilities necessary to remove or control this water.

Jan 1, 1955

By W. R. McMillan, E. A. Gulbransen, K. F. Andrew

Annealed and electrolytically polished pure iron was oxidized between 650° and 850°C at oxygen pressures of 0.1 to 2 microns Hg. Electron optical studies showed that oxidation occurs discontinuously over the surface and orients crystallographically with the substructure of the metal grains. IN previous papers', " the authors described the formation of oxide films on high purity iron at norrnal pressures and at temperatures below 300°C. Electron optical studies showed that the oxide film consisted of many individual oxide crystallites having nearly random orientation on each metal grain. The size of the oxide crystallites depended upon the temperature and upon the extent of oxidation. In these studies the crystallite size varied from 250 to 1800Å. Recently, Bardolle and Benard3 studied the crystal habit of the oxide crystallites formed on Armco iron between 650" and 850°C in what might be defined as a "poor vacuum" atmosphere in which the pressure could be varied between 10-1 to 10-3 mm of Hg. Their results showed that, at 850°C and a vacuum of l0-2 to 10-3 mm of Hg, a few well oriented nuclei of oxide were formed on the metal grains. At pressures between l0-1 to 10-2 mm of Hg, many oriented nuclei of oxide were formed. At 750°C the metal surface was bright although an oxide was present. Unfortunately, the extent of oxidation, the oxygen pressure, and the influence of carbon in the metal were not determined, and it was, therefore, impossible to give a theoretical interpretation to the very beautiful light micrographs. Bardolle and Benard used the light microscope to determine the crystal habit of the oxide and X-ray diffraction to determine the orientation relationships. It was believed that the use of controlled amounts of oxidation at high temperature is an important method for the study of the initial stages of oxidation of metals at high temperatures. This paper presents the first results of an electron optical study of this problem for iron. Since the electron microscope and electron-diffraction methods using stripped oxide films and surface replicas yielded finer details of the crystal habit and structure of oxide film, these methods were used in this study. Two types of iron having different carbon contents were used: Puron and Armco* iron. A com- parison of the results for these materials made possible a study of the influence of the surface oxide-carbon reaction on the initial stages of oxidation. Before discussing the experimental results, the thermodynamic equilibria of 1—the oxidation reaction, 2—the surface oxide-carbon reaction, and 3—the solubility of oxygen in iron, will be considered. In addition, it is important to consider the kinetic-theory predictions on the rate of collision of oxygen with the iron surface. Thermodynamic and Kinetic-Theory Calculations Only one type of reaction is usually considered in the oxidation of iron at normal pressures at high temperatures: Fe(a) + 1/2O2(g) = FeO(s) 3Fe(a) + 2O2(g) = Fe3O4(s) 2Fe(a) +3/2O2(g) = a-Fe2O3(s). [11 However, two other reactions may occur: FeO(s) + C (solid solution in Fe) + Fe(a) + CO(g) [2] and Fe(a) + O2(g) e Fe(a) (solid solution of 0,). [ 3 ] In addition, iron will react with the higher oxide at certain temperatures to form FeO. For a complete interpretation of the oxidation of iron at low pres-

Jan 1, 1955

Jan 1, 1955

Jan 1, 1955

By J. Ruben Velasco, Roland B. Mulchay

CANANEA has long been recognized as a remarkable field for geologic study. The copper deposits and rocks of the district have been described by many geologists and engineers, but only the most general correlations have been made between Can-anea sedimentary rocks and other known sedimentary sections in the southwestern United States and northern Mexico. The present paper describes the Cananea sediments in greater detail than has been done before and attempts to fit the Cananea sedimentary section more closely into the geologic time table. The lack of well-preserved fossils has made it difficult to date the sediments accurately in geologic time, but it is possible to make tentative correlations between the Cananea sediments and the southeastern Arizona sections, based largely upon lithology and general position in the geologic column. It appears that sedimentation at Cananea and Bisbee may have been closely similar during Paleozoic time. Even such generalized correlations, however, may be subject to considerable modification in the future. The present study has led to the recognition of other problems of age and mineralization relationships in the Cananea district. Cananea is located in the north-central part of the state of Sonora, Mexico, at an elevation of 5270 ft. It is about 135 miles northeast of Hermosillo, the state capital, and 25 miles south of the international boundary. By road Cananea is 40 miles from the twin towns of Naco, Ariz., and Naco, Sonora, and about 50 miles from Bisbee, Ariz. It is served by the Nogales-Naco branch of the railroad, F.C. Pacifico, and is connected with Chihuahua and Mexico City by the Aeronaves airline. The headwaters of three rivers flowing to the Gulf of California are located in the Cananea Mountains: the San Pedro River, flowing to the north; the Sonora River, flowing south and west; and the Mag-dalena River, flowing west. Elenita Mountain, the highest point in the district, has an elevation of 8140 ft. The Cananea Mountains extend in a series of north-south to northwest-southeast spurs and ridges and are surrounded by gently sloping gravel plains. The mineralized area, lying across the southern and central parts of the range, is about 6 miles long and at most 2 miles wide. Elevations at the mines vary from 5300 ft at Cananea-Duluth mine at the southeast end of the district to between 6000 and 7000 ft at the west end of the mineralized area at Puertecitos-Elenita mines. Principal production has been from the intensely mineralized and altered area of Capote Basin in the central part of the district and the immediately surrounding area to the southeast. The district has produced over 2 billion lb of copper, substantial molybdenum, and minor amounts of lead, zinc, silver, and gold. Total production through 1949 is estimated at more than $300 million. In 1900 large-scale development was started at Cananea by W. C. Greene. Until World War II only high-grade ores were exploited; low-grade ores were extracted after the installation of a large concentrator in the early 1940's, and subsequent operations have been based upon mining and processing ores containing less than 1.0 pct copper from open-pit and underground workings. Mining and concentration of such low-grade ores, however, are made possible only by continued high copper prices, and active exploration for high-grade orebodies has been continued throughout the important mineralized areas. General Geology Study of the involved rock pattern at Cananea has indicated a complex geologic history for the district. Widespread alteration and mineralization have masked many of the salient features and have led to widely varying geologic interpretations over the years. Further work will probably disclose new information which will modify current beliefs. At Cananea a conformable series of sediments of probable Paleozoic age was deposited on an unknown basement. Following Paleozoic time there was an extended period of erosion common to many districts in the southwestern U. S., and there is no present evidence of marine sedimentation at Cananea after the Paleozoic. The eroded surface was eventually covered with a great thickness of extrusive volcanic rocks. The entire series of sediments and volcanic rocks was later intruded by a variety of deep-seated igneous rocks. These included the Cananea granite, the Cuitaca granodiorite, the El Torre syenite, the Tinaja diorite, the Campana diabase and gabbro and the Colorada rhyolite quartz porphyry. Faulting of early age, probably prior to the deposition of the volcanic rocks, may have been responsible for the present position of some of the intrusive rock masses. In the Capote mine on the third and fourth levels the northwest-striking Rick-etts fault zone, with apparent offset of about 800 ft, has been sealed by a dike-like mass of Cananea granite which gradually increases in size with depth. In lower levels of the mine the granite forms a large southeast-plunging mass generally following the course of the Ricketts zone. The granite is not known southeast of the Capote-Oversight mine areas and the Ricketts fault does not appear in the vol-canic~ southeast of Capote Basin, but several plugs of Colorada quartz porphyry cut the volcanics along the assumed general southeast trend of the Ricketts zone. These porphyritic intrusives may be the up-

Jan 1, 1955

By Wm. Snow, J. R. Wallace, E. P. Duchemin

"GeneralA NOT INCONSIDERABLE proportion of the Canadian economy is dependent on the coal mining industry. This is particularly true of the eastern portion of Canada and especially so of the ( authors') province of Nova Scotia. Much has been said about the trying economic straits of the coal industry in Nova Scotia ( 1), faced, as it is, with difficult mining problems, with considerable distance from large markets, and with •competition from other (and usually foreign) fuels. It is of particular interest, at this time, therefore, to discuss one of the larger outlets for coal -that of the production of metallurgical coke.Scope of PaperWhile the title of this paper indicates that it deals with Metallurgical Coke in Canada, the authors beg leave to treat the Canadian industry very briefly and to deal specifically with coal, •coke, and smelting problems with which they are familiar, namely, the operation of the Dominion Steel and Coal Corporation in the Sydney, N.S., area. No mention is made of metallurgical coke for use in the •many foundries in Canada or in the non-ferrons metallurgical industries.Coal and Coke StatisticsA few statistics of the total output of .Canadian coal, production of metallurgical coke, and similar figures for the Dosco holdings (Sydney area only) are shown in Table I."

Jan 1, 1955

By J. Gurland

The effects of variations of carbon content on the constitution and properties of sintered WC-Co alloys were studied. The grain growth of tungsten carbide during sintering was measured and it was shown that it takes place mainly by solution and reprecipitation of the carbide in and from the binder at the sintering temperature. It was found that the decomposition of W3C03C by carburization during sintering is responsible for the formation of very large grains. THE properties of sintered WC-Co alloys are critically dependent upon their final composition and structure. Slight changes of cobalt and carbon contents and small variations of grain size result in marked changes of mechanical properties and performance of products. Previous investigators have studied the microstructure as a function of composition' and have dealt with the influence of cobalt upon properties.' The present work is concerned with the effect of carbon content upon constitution, microstructure, and grain growth during sintering, as well as upon the physical properties of sintered compacts. Phase Boundaries at the Sintering Temperature The WC-Co section through the ternary diagram W-Co-C has been studied by Wyman and Kelley,' Takeda,V andford and Trent," and Rautala and Norton." Two phases, namely WC and a cobalt-rich solid solution (P), appear in the sintered structure if the carbon composition corresponds very nearly to the theoretical carbon content of WC (6.12 pct C). But small deviations from the ideal carbon content will bring about the occurrence of either graphite or the double carbide W,Co3C (7) . The 7 phase was long believed to be metastable, this conclusion being based mainly on the work of Takeda. More recent studies have shown that it is a stable phase of the ternary system,"5 but the actual phase boundaries have not been established and there has been some discussion as to whether or not the 7 phase occurs at some stage of sintering in the fully carburized alloys." In view of this uncertainty it was thought advisable to undertake an investigation of the phases present during the sintering of WC-Co alloys. Commercially available tungsten, cobalt, and carbon powders were used in the present study. A typical analysis of impurities in a sintered compact is reported in Table I. The desired carbon compositions were attained by varying the amount of carbon added to the tungsten during carburization and controlling the composition during sintering by packing the compacts into beds of mixed alundum-carbon powders of suitably selected ratios. The alloys were sintered in a hydrogen tube furnace at 1400°C, then brought to equilibrium at the temperature under investigation and quenched in water. The high temperature phases were identified by metallographic and X-ray diffraction techniques. The samples were etched with a 10 pct solution of alkaline potassium ferricyanide. The phase boundaries, established by metallo-graphic examination, are shown in Fig. 1, which is a vertical section through the ternary diagram at 16 pct Co. The temperatures of the invariant planes, at 1298" and 1357°C were established by Rautala and Norton. The vertical section shows that the three-phase field, WC + 7 + L, extends into the two-phase field, WC + L, but does not include the stoichiometric composition of WC. In practice this means that the 7

Jan 1, 1955

By Robert D. Thomson

Sheet mica is an important material in the manufacture of electronic and electrical equipment. Large quantities are consumed each year as an essential component in generators, transformers, radios, television sets, radar, electric lighting equipment, and electrical appliances. The nature, structural imperfections, and impurities determine to a great degree the usefulness of sheet mica. Proper processing and classification add greatly to its market value. This report is designed to assist producers in understanding the complexities of marketing muscovite sheet mica. ACKNOWLEDGMENTS Special acknowledgment is due S. A. Montague, of Spruce Pine Mica Co. and G. A. Purcell, mica consultant, General Services Administration, for their critical review and many helpful suggestions in the preparation of thin report. Assistance from other industry and Government representatives is acknowledged with thanks.

Jan 1, 1955

By G. M. Ault, G. C. Deutsch

The paper reviews the efforts made to utilize powder metallurgy to solve problems encountered when using alloys at high temperatures. The following subjects are discussed: comparison of wrought and sintered super alloys, sintered aluminum powder, porous materials for transpiration cooling, molybdenum, and cermets. TODAY, powder-metallurgy techniques are be-JL coming increasingly important, producing materials which at the present time cannot be made by any other method. Among these materials are high melting-point metals such as tantalum and tungsten, porous metals for filters and lubricant-containing bearings, electrical contacts and electrodes (i.e., tungsten-copper), cutting tools of the cemented carbides, and magnet alloys. In addition, the powder-metallurgy industry has grown because, through the application of its methods, shaped parts, such as gears, can be produced at tremendous rates with a low scrap loss in comparison with manufacture by casting or forging and machining. In the past few years, by utilizing powder metallurgy, several approaches to the problem of high temperature materials have been investigated. In this paper the authors will review some of the studies on application of materials having properties above 1350°F. Since their experience lies in the aeronautical field, possible uses of powder-metallurgy techniques in the production of aircraft en- gines will be emphasized. A large portion of the work is classified, but such a restriction has not eliminated any field from discussion, although limiting the amount of detail it is possible to present. The development of high temperature alloys from powders and porous metals for cooling will be discussed as well as research done on molybdenum and molybdenum alloys, cermets, and intermetallics. Some studies on the utilization of cermets will be considered along with special problems that have been revealed through these investigations. Special interest in certain factors of sintered aluminum powder (SAP) makes it desirable to discuss this material although its use temperature is below the 1350°F limitation set for this paper. High Temperature Alloys from Powders In general, components made from powders for room-temperature application have been investigated with the primary purpose of taking advantage of the high production rates and economies made possible by powder metallurgy. From the standpoint of properties, the ojective of the powder metallurgist has been to obtain a product comparable to the cast or wrought product that is to be replaced. Comparisons of the properties of alloys made by powder-metallurgy methods with those of similar compositions made by casting and forging are reported in the literature.12 In many cases equivalent

Jan 1, 1955