Search Documents

By H. Kenworthy

Laboratory experiments were conducted on several materials to determine their suitability for the production of mineral wool. By blending raw charges in the proper proportions and in some instances by adding lime, acceptable wools were made from samples originating in Alaska, Florida, Texas, and Virginia. It was shown that satisfactory wools can be produced from many kinds of raw materials if the ratios of acidic and basic constituents are properly maintained. INTRODUCTION The Federal Bureau of Mines has facilities at the Mississippi Valley Experiment Station, Rolla, Mo., for examining and testing mineral-wool raw materials. Samples are evaluated through small-scale wool-blowing experiments, aided by petrographic, chemical, and physical analyses of the raw materials and finished wools. When enough experimental data have been accumulated they are made public through Government reports and periodicals. This report of investigations follows that published in 19513/ and presents test data on samples received and examined since 1951.

Jan 1, 1956

Individual specimens of sphalerite from the Broken Hill lode vary considerably in manganese and iron contents, even within the same orebody, so that study of the overall variation of manganese and iron content of the sphalerite calls for the analysis of a large number of specimens. This difficulty has been overcome by analysing a series of recleaned zinc concentrate products, prepared from stope samples and their equivalents, from most of the developed sections of the lode. The analyses reveal that during the formation of the sphalerite the concentrations of iron, manganese and zinc in the mineralizing solutions varied independently of one another from place to place in the forming orebodies, and also in time.The overall pattern of variation of the iron and manganese contents of the sphalerite in the several orebodies of the lode bears a general resemblance to the overall pattern of distribution shown by several other elements, notably, cadmium, lead, bismuth and arsenic. The iron content of the sphalerite indicates that it was formed at a temperature of 6000 C. or higher, but the variation in its iron and manganese contents demonstrates that Kullerud's method for determining the temperature of formation of sphalerite from its iron content must be used with caution if only single specimens of sphalerite are available.INTRODUCTIONThe four chemical analyses available of specimens of practically pure sphalerite from the Broken Hill lode (Table 1) reveal that the manganese content of the sphalerite varies considerably, and that there is a significant variation in its iron content. The variations revealed between individual specimens within the same orebody in the same mine suggest that specimen material is unsatisfactory as a basis for studying the overall manganese and iron contents of Broken Hill sphalerite, unless a great number of specimensis analysed.

Jan 1, 1956

By John B. Gayle

[The coking time exerts a Considerable influence on the throughout of a coke oven, and for this reason a large number of papers dealing with the relation between coking tine and the different operating variables have been published. Although all of the factors known to ink influence the coking time have been studied, agreement leas not boon reached on several questions, 3/4/ and it appears worthwhile to evaluate any data that become available during investigations of the carbonizing properties of various oafs and coat blends, this report, therefore, includes a Study of the relation between coking lime and flue temperature and represents the second phase of overall investigation ion of factors influencing the coking time in slot-type ovens.]

Jan 1, 1956

The paper describes a cyclic method for processing manganese ores using sodium sulphate as the basic reagent. Sodium sulphate is electrolyzed in a diaphragm cell to give an anolyte sodium sulphate acid and a catholyte containing caustic soda, a part of which is carbonated in a cyclic manner to Form ash. and reduced ore is leached with the anolyte to dissolve the manganese and the impurities are precipitated by addition of catholyte. Manganese in the pregnant solution is precipitated as synthetic rhodochrosite with a carbonated catholyte, and sodium sulphate is regenerated. Calcining the manganese carbonate site a high-grade product and the carbon dioxide is returned to the carbonation step. the results of laboratory tests using cells equipped with synthetic fiber diaphragms and permselective membranes which permit transfer of using or cations during electrolysis are described. The article from which the above abstract is reprinted appears in Trans. AIME (1955) 203, p. 51; Journal op Metals (January 1955).

Jan 1, 1956

By P. A. Beck, A. Merlini

Quantitative texture determinations were made for rolled and for rolled and annealed strips of 3, 6, and 10 pct Zn brasses. The main components of the rolling texture gradually shift over a wide composition range from the orientation characteristic of copper to that of 70-30 brass. At least the main features of the corresponding gradual changes in the annealing texture may be accounted for qualitatively on the basis of the oriented growth theory of annealing textures. All the oriented nucleation-type theories are notably less successful in accounting for the observed textures. EARLIER investigations by von Goeler and Sachs,' Dahl and Pawlek,' and Brick, Martin, and Angier" suggested that the annealing texture of copper is more sensitive to the addition of solute elements than the rolling texture. It was reported3 that the cube texture changes over into a brass-type recrys-tallization texture on addition of about 1 pct Zn, while the deformation texture changes only at about 5 pct Zn. Such behavior would be difficult to reconcile with any theory of annealing texture formation that relates the annealing texture to the deformation texture. In particular, the oriented growth theory of the cube texture" is based on a certain orientation relationship between the cube texture and the main components of the deformation texture which could not be reconciled with the reported behavior of low brasses. It was, therefore, of interest to re-examine these textures by means of the quantitative methods now available. The deformation and annealing textures of rolled a brasses with approximately 3, 6, and 10 pct Zn have been determined in terms of (111) and (200) pole figures. Experimental Methods The chemical analyses of the Cu-Zn alloys of commercial purity used in the present work are given in Table I. Chill-cast bars of the tabulated compositions were rolled and annealed according to the following schedule: I—rolling from 1.2 to 1.02 in. thickness, 15 pct reduction area, annealing 15 min at 450°C; 2— rolling from 1.02 to 0.867 in. thickness, 15 pct reduction area, annealing 15 min at 450°C; 3—rolling from 0.867 to 0.600 in. thickness, 31 pct reduction area, annealing 2 hr at 540°C; 4—rolling from 0.600 to 0.400 in. thickness, 33 pct reduction area, annealing 2 hr at 480°C. In the final straight rolling of 96.25 pct reduction area, the strips were reversed end to end after each pass. The final annealing temperature was determined for each alloy by annealing specimens of the cold-rolled strips in salt bath for 5 min at varying temperatures. The results of the hardness measurements are given in Fig. 1, where the final annealing temperature used for each alloy in determining the annealing texture is indicated by a cross.

Jan 1, 1956

By Peter M. Power

A microscopic study was made of a series of simultaneous slag and metal samples taken from a low carbon basic open hearth heat. An attempt was made to identify the various micro-constituents found. As the various impurities in the bath are oxidized, the metal structure changes from that of high-phosphorus white cast iron to that of low.-carbon steel. A detailed study of phosphorus distribution is included. The acid run-off slag has an .acicular orthosilicate structure which changes on 'shape-up' to a very basic tri-calcium silicate and calciuim ferrite structure. Many unidentified minor constituents are present in the slags. Though metallography will never replace chemic.al analysis of the bath, the microsopic study of polished slags has some promise of being useful in slag control work.

Jan 1, 1956

By H. R. Shell

The work on synthetic mica and related subjects is being reported in a series of technical articles (see Supplementary Bibliography), each of which describes some special aspect of the subject. This is the final report on chemical analysis of the fluoride-containing silicates. A condensation of this report has been published (26).3/ Chemical analysis affords one of the best means of ascertaining the final com-position of either a heterogeneous mass or a single pure crystal, particularly where some constituents may be volatile. The analysis of fluoride-containing silicates was not so well known or understood that highly accurate results were commonplace. For example, on synthetic mica a university laboratory reported 11.6 and 9.2 percent fluoride when at least 13.3 and 11.3 percent were present, respectively; a commercial testing laboratory reported 9.14 percent as compared to 12.6 percent; and a glass company reported 7.0 percent as compared to 9.0 percent present. No intimation is made that these analysts could not have done better, but the point to be stressed is that the methods in use were long, tedious, and generally required a certain familiarity for best results.

Jan 1, 1956

By C. T. Baroch

As part of a general program for investigating all phases of titanium production, argon was substituted for helium in the reduction step at the Bureau of Mines pilot plant, which employed a modification of the Kroll, or magnesium-reduction, process. Argon was substituted for helium in 108 of the 140 batches of sponge made during 1 month's reduction operations for July 1954. Argon was substituted for helium satisfactorily, with only slight modifications in technique. Metal quality, feed rate of TiC14, magnesium efficiency, and average production per batch were closely comparable with either gas. Argon runs were slightly more troublesome because of the formation of condensable chloride complexes, which tended to plug feed and vent lines and to entrap deposits of lower titanium chlorides on the reactor-pot lids. These lower chlorides were objection-able because they were pyrophoric and created obnoxious fumes when pots were opened. When feed and vent lines became plugged care was required in poking or unplugging these lines to prevent air from entering the reactor. These problems were relatively minor, and continued development of reactors and techniques for the use of argon should further minimize objectionable side reactions obtained when argon is used.

Jan 1, 1956

By Russell R. Trengove

Bureau of Mines exploration at the property of the Tulare County Tungsten Mines was by core drilling from the surface from May 16, 1950, to July 13, 1950. The property is in the western foothills of the Sierra Nevada Range, 18 miles northeast of Lindsay, Calif. It has been in almost continuous production since 1942 and has produced 40,831 units of tungsten trioxide (W03) with a grade of approximately 67 percent. The work performed comprised a study of the geology, mapping the area, sampling the outcrops, and diamond drilling the area adjacent to the mine workings. Ten holes were drilled for a total of 1,824 feet. Ore reserves were found to be confined to tactite zones in a surface area approximately 250 by 400 feet and extending downward about 350 feet.

Jan 1, 1956

By E. R. Rodriguez

Improved practice resulting from recent changes in the method of supplying compressed air and in pneumatic drilling equipment used in secondary drilling and in development work at the Morenci mine of the Phelps Dodge Corp., has resulted in improved safety conditions, as well as in a reduced cost per foot of drilling. A large stationary compressor installed outside the mining area and the compressed-air pipelines in the mine were replaced by portable compressor units. A self-propelled, self-contained drilling unit was obtained for drilling large footages where short moves were involved. Large wagon-drill units were replaced by faster and lighter drill machines and conventional bits by carbide insert bits. The safe practices employed in air drilling and in the related blasting and scaling operations have contributed to an excellent safety record at this mine. The complete sets of instructions listed in the company codes of safe practice aid materially in training employees.

Jan 1, 1956

By W. D. Bennett

AN interesting effect has been observed in the vacuum etching of titanium in the high temperature ß phase. Using a high vacuum annealing furnace, operating at less than 2x10-6 mm with a tubular titanium liner, it has been found possible to etch polished metallographic specimens at different temperatures between room temperature and 1000°C without contamination or increase in hardness.' Heat etching of titanium has been reported by other workers,' but the following example is of interest as an experiment under high vacuum in the absence of any contamination. Two polished specimens of iodide-processed titanium are placed at different positions along the axis of the furnace corresponding to temperatures of 900" and 800°C above and below the a-ß transus. The specimens are then raised to these temperatures and annealed simultaneously for 3 hr under the same high vacuum conditions. After cooling and withdrawing the specimens, their surfaces are photographed without further treatment. Figs. 1 and 2 show the results for the 800" and 900°C specimens, respectively. Fig. 1, corresponding to a vacuum etch in the a region, shows a typical equiaxed structure with what appears to be a slight shift of grain boundaries. Fig. 2, corresponding to a vacuum etch in the ß region, shows an equiaxed type of structure with the growth of striations in certain grains. The striations are only superficial, as a light polish and chemical etch restores the clean equiaxed structure. The vacuum etch, occurring as it does above the a-ß transus, records the state of the metal in the ß phase by means of the surface relief produced by the selective evaporation of metal from different grains; the metal itself reverts to the equiaxed a on cooling. The nature of the ß etch" (Fig. 2) suggests that, in transforming from the close-packed-hexagonal a to the body-centered-cubic ß lenticular-shaped laminae are formed parallel to common planes of the two structures. This would explain why some grains appear to be unaffected by the etch. The technique has interesting possibilities in the investigation of the mechanics of high temperature transformation. Acknowledgment This note is published by permission of the Deputy Minister, Dept. of Mines and Technical Surveys, Ottawa, Ont., Canada.

Jan 1, 1956

By H. C. Chang, N. J. Grant, A. R. Chaudhuri

During the creep of coarse-grained polycrystalline magnesium at elevated temperatures, a nonbasal type of slip was found to play an important role in the deformation processes. The nonbasal slip traces were examined metallographically in eight specimens (13 grains) and the observed glide plane located stereographically for each grain. The tests were run at 500&apos; and 700°F at stresses of 148 to 786 psi. Based on these measurements and theoretical calculations, the crystallographic elements for nonbasal slip were determined. WHEN a metal deforms by slip, the conventional appearance of the slip bands on the surface of a specimen is that of straight lines. Such is the behavior of the face-centered-cubic metals, as for example, aluminum. The particular slip system on which slip occurs in these metals is governed by the criterion of resolved shear stress. Work on the body-centered-cubic metals a-iron,&apos;. &apos; molybdenum, and columbium4 has shown that the process of slip is somewhat more complicated than the simple gliding of one close-packed plane of atoms over another in a close-packed direction and that it results in the formation of wavy and irregular slip traces on the surface. The recent reviews and experiments of Vogel and Brick and Chen and Mad-din3 show that, for the body-centered-cubic metals, the resolved shear stresses along the planes and the degree of close-packing do not necessarily determine the slip system. Theirs and other investigations indicate that a complete understanding of the slip process in the body-centered-cubic metals is not yet possible. However, one behavior displayed by all these metals is that the slip direction is invariably one of the close-packed directions <11l>. The wavy nature of the slip-band traces has been explained on the basis of cooperative slip by planes sharing this same slip direction.1&apos;3l&apos; It is generally acknowledged that, when the hexagonal-close-packed metal magnesium (axial ratio c/a = 1.624) deforms by slip at room temperature, it does so by basal slip in the close-packed direction <1I%>. This type of slip has the conventional appearance of straight lines and is governed by the critical shear-stress law. Schmid and coworkers" showed that basal slip was operative in the temperature range of —185" to 300°C (—300" to 572°F). Work by Servi, Norton, and Grant6 has shown that, during the creep of coarse-grained aluminum at high temperatures, new slip systems come into operation. The existence of a new high temperature slip system at temperatures greater than 225 °C (437°F) for magnesium was suggested also by Schmid. This was later indicated by Bakarian and Mathewson&apos; to be slip along the pyramidal planes (10i1) in the close-packed direction <11%>.* They * Mention will be made in the text of pyramidal planes and prismatic planes. The pyramidal planes referred to are the type I. order 1 of the form {10il); and the prismatic planes of the type 1 of the form (10i0). For the sake of brevity, they are termed in the teat as pyramidal (10il: and prismatic (10i0) planes, respectively. Where reference is made to the pyramidal plane type 1, order 2 of the form {10i2), they are referred to as the pyramidal planes of the type (10i2:. observed that this kind of slip resulted in irregular markings on the specimen surface. According to them, a possible cause for the appearance of the markings was due to "limited accessory slip on the pyramidal {10i2) planes." Burke and Hibbard," on deforming a single crystal of magnesium at room temperature, found evidence of slip on a pyramidal plane {1011). They explained it as being due to the effect of grip restraints. It is pertinent to note at this point that, although basal slip has received a fair amount of attention, only two specimens have been investigated, that of Bakarian and Mathewson and of Burke and Hibbard, to establish the elements of nonbasal slip in magnesium. During the study of the deformation mechanisms

Jan 1, 1956

By J. P. Myers, A. H. Flagg, E. S. Mardock, J. L. P. Campbell, J. M. Terry

The development process for the use of radioactive tracers as a means of locating zones of permeability is discussed. The general techniques for the safe handling of radioactive materials is given as developed by the Lane-Wells Co. and Well Surveys, Inc. The prob1em and. successes with tracers in waterflood systetns, oil and gas injection profiles, fracture sand tracing, squeeze (ement tracing. lost circulution, and cement top localion are discussed and illustrated. INTRODUCTION The exact location of the permeable zones lying within the productive horizon has been a major problem faced by the petroleum engineer for decades, and it has been a problem which has seldom been solved with certainty. Reservoir engineers usually have to incorporate a question mark in their estimates of future reservoir performance because of blanks in the core data. Although the use of radioactivity or electrical logs for the estimation of porosity has been of great assistance in furnishing a record for the reservoir engineer, this application of logging data has not completely solved the problem. In short, the industry needs an in-situ well surveying method which can locate and estimate the permeability of the zones existing within a given pay section. The initial development work with radioactive tracers has been towards filling the need for permeability information. Progress to date permits the location of permeable zones with a qualitative estimate of their relative importance with respect to permeability. The calibration of the method is still incomplete. but present development work on tracer preparations, borehole effect correction factors, and instrument limitations give a promise of quantitative "permeability profiles" in the near future. The development work on the radioactive tracer method discussed here began several years ago in the laboratories of Well Surveys, Inc., in Tulsa. At the outset of this work, three approaches to the problem were visualized as follows: 1. A fluid carrying a soluble, chemically inert, gamma ray emitting isotope is pumped down the borehole and out into the permeable zones of the formation. The greater gamma activity of the permeable zones thus permits them to be differentiated from the impermeable zones which contain no active tracer. It was found difficult to obtain a tracer material which was chemically inert. Absorption to some degree was noted in all experiments. Also, it proved impossible to hold the tracer near the horehole where it could be logged. 2. A fluid carrying a soluble, gamma ray emitting isotope is pumped down the borehole into the permeable formations. In contrast with proposal 1, above. the tracer is chemically active with the fluids and materials in the pore spaces of the permeable zones. The permeable zones are thus indicated by their higher radioactivity level. The main difficulty in this proposal was finding a tracer material which would not be absorbed by shale as well as in the permeable porosity. Very little field work was done with this system. 3. Radioactive particles suspended within the injection fluid are pumped down the well. As the fluid enters the permeable formations, the radioactive particles are filtered out on borehole wall. The permeable zones are differentiated from the impermeable by the gamma ray activity deposited on the formation wall.

Jan 1, 1956

By T. S. Lovering

GEOCHEMICAL prospecting extends the age-old method of searching out lodes with a gold pan and rationalizes the prospector&apos;s hunch that certain plants are associated with ore. It uses sensitive but cheap and rapid analytical methods to find the diagnostic chemical variations related to hidden mineral deposits. Exploration geologists can gain tremendous assistance from this new tool, although its optimum use is not simple. To bring out the geochemical pattern that reveals the presence of a hidden ore deposit with a minimum number of samples requires a combination of shrewdness, chemical knowledge, and exploration geology. The use of sensitive analytical methods for prospecting had its start in the 1930&apos;s in northern Europe, where Scandinavian and Russian geologists had some success in these early efforts. Very little geochemical prospecting was carried on in the United States at this time, and no sustained interest was manifest until the close of World War 11, when geochemical investigations were started by the Mineral Deposits Branch of the U. S. Geological Survey. The purpose of these investigations was to apply geochemical principles and techniques to surface exploration for mineral deposits. Both the research on analytical methods and the routine trace analyses for field investigations were at first conducted by a single group, but it later became apparent that the trace analyses could be done by men of less experience than that required for successful research on methods. For the past several years there have been two groups of chemists, and although their functions overlap, three of the chemists are chiefly concerned with research, while four to six other men make the trace analyses for field projects. The chemical investigations, as well as the field projects of the Geochemical Exploration Section, concern only those phases of the subject that are appropriate to a government organization; every effort is made to help private industry, but not to compete with it, in finding orebodies. The chief aim of the Section, therefore, is to develop new analytical techniques and publish the results promptly, to carry out field investigations of the fundamental principles of geochemical dispersion, and to field test promising- techniques under controlled conditions. Some routine geochemical exploration work is carried on in connection with DMEA loans, and in district studies where the project chief wishes geochemical information on certain areas for his report. It should be emphasized, however, that geologists of the Geochemical Exploration Section are primarily concerned with fundamental principles underlying the distribution, migration, and concentration of elements in the earth&apos;s crust. To facilitate the use of geochemical methods the USGS has published much information on its methods of analysis and has provided opportunities from time to time for qualified professional personnel to study these methods, to work in the USGS laboratory, or to attend demonstrations of the analytical techniques at the Denver Federal Center. Typical of the research carried on are the problems now being investigated: 1) Development of rapid and sensitive analytical methods suitable to the determination of traces of metals and other minor elements in various materials, such as rock, soils, plants, and water. At the present time attention is being concentrated on U, Bi, Cr, and Hg, and satisfactory rapid trace analytical methods are virtually perfected for U and Bi. Good methods are also available for: Cu, Zn, Pb, Ni, Co, As, Sb, W, Mo, Ag, Nb, Ge, V, Ti, Fe, Mn, S, and P. 2) The relation of geochemical anomalies in plant materials to the geochemical distribution of elements in soils surrounding the plant. 3) A study of the dispersion halos in transported sedimentary cover such as glacial drift and alluvium over known orebodies. 4) A study of the behavior of ore metals in the weathering cycle. 5) A study of the behavior of the ore metals during magmatic differentiation. This requires a study of the distribution of minor metals in fresh igneous rocks and their component minerals in a well established differentiation series and in adjacent country rock. 6) A study of the dispersion of metals in primary halos in the wall rock surrounding orebodies. 7) Regional and local studies of the metal content of surface and groundwater in mineralized and barren areas. Many field projects of the Mineral Deposits Branch also require the services of USGS chemists during their investigation of the geochemical environment of ore deposits. From the work that has been done certain general principles have emerged. Concentrations of an element that are above the general or background value of barren material are called positive geochemical anomalies or simply an anomaly, whereas values less than background are called negative anomalies. The anomalies most commonly investigated in geochemical prospecting are those formed at the earth&apos;s surface by agents of weathering, erosion, or surficial transportation, but more and more attention is being given to primary anomalies found

Jan 1, 1956

By J. F. Elliott

PRESENT knowledge of the usual metallurgical slags indicates that they are, for the most part, rather complex in behavior and as yet there is no ready means for describing, in a simple manner, the behavior of any one of them. One of the best known slag systems is the iron oxide-silica-lime ternary which is the basic "solvent" in a number of important metallurgical refining operations, the basic open hearth being one of the most important. In this operation, the slag dissolves such components as sulphur, phosphorus, manganese oxide, and magnesia. Considerable study of this slag system and the behavior of these additions has been carried out in the past by a number of authors, as has been summarized in several critical reviews.&apos;,&apos;2 However, except for determination of the activity of iron oxide, only a limited amount of effort has been directed towards developing, from these data, an understanding of the general behavior of the basic solvent. Reported here are the results from a series of calculations based on data from the literature which permit a semiquantitative evaluation of the activities of iron oxide, silica, and lime (plus magnesia) in the ternary system at 1600°C. The preliminary results, which were reported briefly at a symposium held by AIME in 1953, have been revised and are completed. The steps in the calculation are as follows:* I—establish the activity curves and the curve of the excess molar free energy of mixing at 1600°C for each of the binary systems, 2—construct the activity surface of iron oxide for the ternary from the data on the binary systems and information available in the literature for the ternary area, 3—determine the surface of excess molar free energy of mixing for the ternary system from the activity surface of iron oxide and from the molar curves obtained for the binary system, and 4—differentiate the ternary surface of the molar excess free energy of mixing to obtain the ternary surfaces for the logarithm of the activity coefficients for silica and lime (log rslo, and log rc.~). Si0,-Fe,O: Schuhmann and Ensio have measured the activity of iron oxide in simple iron oxide-silica slags when in equilibrium with y iron. Their data recalculated to 1600°C are shown in Fig. 1. Also included is a point representing a measurement by Gokcen and Chipmana of the activity of iron oxide at 1600°C at the point of saturation with solid silica. For convenience and in accordance with other treatments,&apos; the calculations are based on the hypothetical component, FelO, which is obtained by converting all the analyzed iron in the slag to FeO. In spite of Schuhmann and Ensio&apos;s conclusion that the activity of iron oxide in the system does not vary with temperature over the experimental range of 1258" to 1407"C, the data are corrected to 1600°C assuming that temperature does have an effect. It was felt to be most reasonable to assume that the term log rr.10 is a linear function of the reciprocal of the temperature. Reyu has indicated that an effect of temperature on the activities in this system is to be expected from the Schuhmann and Ensio data. In essence, the correction consists of multiplying the experimental value of log rf,,o by the ratio of the experimental temperature in Kelvin to 1873°K. The magnitude of the correction is not large, being approximately 11.5 pct of the experimental value of log rve10. A very minor correction was necessary to compensate for the fact that the slags were in equilibrium with y iron in the experiment, while at steel-making temperatures they would be in equilibrium with liquid iron. Data for the correction were obtained from Darken and Gurry. The standard states established are pure liquid iron oxide (FelO) in equilibrium with pure liquid iron (with the appropriate amount of oxygen in solution) and pure liquid silica. The method of plotting in Fig. 1 is convenient for the calculation of the activity of liquid silica and permits a reasonable extrapolation for the activity of Fe,O in the ranges where no experimental data are available. The uncertainty in the extrapolation to infinity at one terminal where Nvelo = 1 for the usual Gibbs-Duhem integration is reduced considerably by this method. The region of two coexisting liquid phases is estimated to range from 1.8 to 41.7 mol pct Fe,O. The nature of the activity curve for the single-phase region indicates that the activity of iron oxide across the two-phase region is very close to 0.39. Computation of the function log ~F,,o/(1— NF,,o)&apos; for this region (dashed line) in conjunction with the curve through the adjusted experimental data indicate the best probable value of 0.382 for alPe,o in the two-phase area. The line from 0 to 0.018 Nf~~o is obtained by assuming that the component follows Henry&apos;s law. In this range, the value for log rveto is 2.59. Appropriate mathematical manipulation of the plotted linet yields the activity curves for the The curve AF", the excess molar free energy of mixing (actual minus ideal), as shown in Fig. 3 is also computed from Fig. 1. This curve is required for subsequent calculations. CaO-Fe,O: The phase diagram for the lime-iron oxide system when in equilibrium with liquid iron is not well known but there appears to be no intermediate compound present. This fact as well as the activity values for Fe,O extrapolated to the CaO-Fe,O binary from Taylor and Chipman&apos; tend to indicate somewhat negative deviations from ideality for the activity curves for the two components. Strong indication of this is evident in Fig. 1 where are plotted the points computed from the estimated activities of Fe,O for the binary system.&apos; It appears that the best line through the data is a horizontal straight line. Because of the general indication of the slight negative departure from ideality, the line is extrapolated horizontally to NF~,o = 0. It is con-

Jan 1, 1956

By Kenneth L. Cook

THE five serpentine masses exposed within the northern half of Riley County, Fig. 1, constitute a major part of the few exposures of igneous rock in Kansas.&apos; Although not many subsurface data are available for this part of Riley County,2 six deep wellsV indicate that the basement complex lies between 2500 and 3000 ft below the earth&apos;s surface. A northwestward-trending ridge in the present basement surface, which extends across the northern half of Riley County, is indicated on Mettner&apos;s contour map.&apos; The serpentine masses lie in a region that was active during Pennsylvanian and Permian time along two main tectonic trends, which may, in part at least, have developed contemporaneously." One trend is northeasterly, as evidenced by the Nemaha anticline, the Abilene anticline, the Voshell anticline, and many other smaller northeastward-trending folds. The other trend is northwesterly, as evidenced by the central Kansas uplift, the Salina basin syncline, and smaller northwestward-trending folds. The area of the Abilene anticline was actively deformed during much of this time, and the present surface rocks, for the most part Permian in age, show many normal faults." The Bala and Leonardville intrusions lie within a mile of the axis of the Abilene anticline, Fig. 1, as mapped by Wallace Lee;&apos; the Randolph No. 1 and Randolph No. 2 intrusions lie within about 5 miles of the axis; and the Stockdale intrusion lies within about 8 miles of the axis. The igneous rocks have intruded horizontal or gently dipping limestones and shales that are late Permian in age.V he period of intrusion, according to Moore and Landes, was probably Cretaceous.&apos; At present a detailed description of the petrography is available for only the Bala intrusion. Moore and Haynes&apos; describe the rock at Bala as a green, serpentinized, porphyritic, peridotite breccia containing inclusions of shale. The ground mass consists chiefly of serpentine and calcite with considerable chromite (5 to 10 pct) and some magnetite. The phenocrysts consist principally of altered olivine with some altered augite and biotite. Although probably different in petrographic details, all the serpentine masses are somewhat similar in that 1) they consist of a dark green, fine-grained ground mass of igneous rock containing many xeno-liths composed of fragments of the neighboring sedimentary rock; 2) they tend to form small mounds on the landscape, thus indicating their greater resistance to weathering and erosion; and 3) they are magnetic. Previous Magnetic Survey of the Bala Intrusion: To the writer&apos;s knowledge, only the Bala intrusion had been surveyed with a magnetometer prior to the magnetic surveys discussed in this paper. Dreyer8 interprets the intrusion as a vertical, eastward-plunging dike, on the basis of the results of his magnetic survey, Fig. 1, with a vertical magnetom-

Jan 1, 1956

By E. A. Sobering

Hydraulic filling or sand filling is a system used to fill underground excavations with a dense pulp. Milltailings are commonly used. The resultant fill, after being placed and de-watered, is known as hydraulic fill. These fills have been effectively used to (a) provide immediate support of the workings place during stoping; (b) .facilitate the recovery of pillars; (c) limit surface damage by subsidence; (d) permit the mining of parallel hanging-wall orebodies; (e) stabilize the ground in mines, thereby reducing the rock burst hazard; (f) control and prevent mine fires; and (g) solve tailings disposal .problems. The various uses of hydraulic filling have been developed during the last ninety years. In 1864 it was employed only to control surface subsidence. Since then, this system has been successfully applied to meet specific ground support problems. Methods of handling mine-fill derived from a source outside the stope include transportation ?Of the material by hand, mechanical, pneumatic, and hydraulic means, or a combination of these methods. The hydraulic method has many advantages not found in the others; a significant advantage is the low compressibility of the material when compared to other mine-fill material. The hydraulic filling operation includes the .preparation and transportation of the pulp. The underground practices in .placing the fill vary from mine to mine. The chief reason, formerly, for using hydraulic fill was the exceptional support it provided, but recently it has proven an important means of reducing mining costs. This is especially true where labour is a large part of an alternative method, or where timber consumption is greatly reduced. The indirect benefits of hydraulic filling are probably as important as the direct benefits, and few important disadvantages exist.

Jan 1, 1956

By C. W. Spencer, J. Singer

A PARTIAL phase diagram for the As-Te system is given in Hansen.&apos; The only compound reported is As2Te3, melting at 362°C. Stoichiometric quantities of reagent-grade elements were reacted in evacuated quartz and directionally cooled. The resulting ingot consisted of very thin threadlike crystals from which only very small single-crystal fragments were isolated. A powder diffraction diagram disclosed nonisomorphism with the analogous V-VI compounds insofar as these have been reported; Sb2S3, As2S3, Bi,S,, and Bi2Te3 data in the ASTM index of powder patterns, together with the single-crystal data on Sb2Se3,2 were used for the com- parison with the observed spacings. Single-crystal data confirmed the uniqueness of the As2Te3 structure. Single-crystal Weissenberg diagrams have so far yielded the following data: As2Te3 is monoclinic, space group C-m (OkO data still lacking), a = 14.4A, b = 4.05A, C = 9.92A, ß = 97". The cell volume is about 5802. The set of isomorphous ortho-rhombic cells of Sb2Se3, Sb2S3, and Bi2S, are apparently related to As,Te, in having one lattice constant close to 4.0 and with cell volumes as large as 540A8. Assuming Z = 4 for As2Te3 also, the density is calculated as 6.1 which agrees well with a roughly determined value of 6.0. A complete structure analysis is under way.

Jan 1, 1956

Titanium tetrachloride may be reduced to trichloride with hydrogen on a hot tungsten filament and other hot: surfaces. The effect of temperature, time and size of t.he filament on the rate of reaction has been studied. A laboratory unit for preparing a few pounds of trichloride at a time is described. The yield of trichloride is 2&#183;2 - 2&#183;4 gm/sq. cm. of hot surface/hour at 1,000&#176;C. and the energy requirement 3&apos;5-4 kWh/pound of trichloride produced.&apos;INTRODUCTIONThe lower chlorides of titanium (titanium tri- and dichlorides) are amenable to electrolysis, being electrovalent in nature. Furthermore, relative to other oxygen-free titanium salts, they are easy to prepare in a pure state and their use has been investigated to prepare titanium. The experimentaJ work described in this paper deals with the preparation of titanium trichloride by reduction of titanium tetrachloride with hydrogen on hot surfaces.REDUCING AGENTS FOR TITANIUM TETRACHLORIDEThe free energy diagram (Fig. 1) for the formation of chlorides suggests that titanium&apos; tetrachloride may be reduced to trichloride by various reducing agents such as aluminium, zinc, arsenic, antimony, tin, mercury, silver, hydrogen, sodium, potassium and magnesium. Ruff and Neumann (1923), Thorpe (1885) , Billy and Brasseur (1935) and Seurbert and Schmidt (1892) used various metals to reduce tetrachloride to trichloride and found that the yields were invariably low and the products difficult to separate.Besides the metallic reducing agents, hydrogen may also be used to reduce titanium tetrachloride to trichloride.Goerges and Stahler (1909) obtained a deposit of violet...

Jan 1, 1956

By E. J. Gleim

This report describes a trip to Europe in the interest of safety in coal mines. It reviews the Eighth International Conference of Directors of Safety in Mines Re-search, which met in Dortmund-Derne, Germany, July 5-10, 1954, to discuss results of studies made in different countries to improve health and safety conditions under-ground. It also summarizes information on subjects of special interest in the United States gained by the writer in visits to mining experiment stations in Belgium, France, and England. The efforts being made to protect life and property underground were discussed, and ideas and experiences were interchanged freely, not only during the conference but also during visits to the several countries. Helpful information was obtained on many topics of interest, but time did not permit as thorough a discussion on some of them as might be desired.

Jan 1, 1956