Search Documents

By Jaime Fernández Concha

El presente texto señala la ubicación, fisiografía, geología general y cubicación del depósito de Fierro del Cerro Tarpuy y Cerro Mirador ubicado en el departamento de Arequipa.

Jul 1, 1956

By Juan Rassmuss

El presente artículo señala el valor del azufre y la influencia del método de beneficio en lsu explotación. Asimismo, se describe los yacimientos de Piura y los de Báyovar, como del extremo norte está Ticsani, Tutupaca, Yucamani, Cano y en el Sur, Paucarany. La formación de estos yacimientos se debe a lla oxidación parcial de sulfuro de hidrógeno de origen volcánico, a excepción de los yacimientos de Bayovar y Piura, considerados como productos resuidual de petróleo.

Jul 1, 1956

By Robert C. Weed

Leaching in place at Cananea began in the 1920's on a limited scale. The first plants were small wooden boxes located underground in the Capote and Oversight mines, and output was low. Scrap iron was used as precipitant. Later several other small plants were started up. Leaching was limited entirely to underground areas, and production remained low. The Veta precipitating plant, the first on a larger scale, was put into operation in the late 1920's. After a period of intermittent service it was rebuilt in 1946 and has since been running continuously.

Jul 1, 1956

By F. W. McQuiston

Teamwork is the key to an efficient organization. Cooperation among mining staff members is an obligation owed to the company. The more cooperation the metallurgist receives from underground, the higher milling yield will be, which in turn makes for a greater mine profit. There is no pay for metal left in mill tailings. The metallurgist is not in a position to be of help to either the geologist or mining engineer, but can receive valuable assistance from both. Therefore, the metallurgist must win underground cooperation. The mining engineer is usually interested in geology because of its relation to ore control; in milling because that is where the rock goes. However, any overlapping of interest between geologist and metallurgist is quite remote.

Jul 1, 1956

By E. G. Williams

Conveyors were first used underground at Miami Copper Co., in the latter part of 1947. At that time some of the stoping area was too heavy and too close to the haulage level to use conventional haulage. To get the haulage drifts out from under the stoping area belt conveyors were used for the additional lateral transfer. Since 1947 more than 8 million tons have been mined in this manner, with as many as four belt type stopes in production at one time. When the mining plan for the new low grade was worked out, it was decided to use belts on what otherwise would have been short train haulage transfers to move the ore laterally to centrally located concrete ore passes. One group of these stopes has grizzly levels on the 570, with a belt level on the 670; the other group has grizzly levels on the 720 and belt levels on the 820, with the concrete ore passes bottoming on the 1000, or the existing train haulage level.

Jul 1, 1956

By J. C. Holm

Although the main constituents of Portland cement are the oxides of calcium, silicon, aluminum, and iron, characteristics of the cement are seriously affected by such contaminants in the raw materials as magnesium, phosphorus, sodium, potassium, sulfur, and others of lesser importance. Sources of cement raw materials comprise a long list of minerals occurring in nature in various degrees of purity. The calcareous raw materials are generally limestone of purity varying from calcite to cement rock (a low-grade limestone of natural, almost correct chemical composition), chalk, marl, seashells, coral, and coral sand. The argillaceous raw materials supplying silicon, aluminum, and iron are mainly various forms of clay and shale, to which may be added silicious sand, iron ore, bauxite, or kaolin for minor adjustment of the chemical composition.

Jul 1, 1956

By L. Bombardieri, H. F. Mills

Iron King mine, producing gold-silver-lead-zinc-ore, is 10 miles east of Prescott, Ariz. At present the 1806 level is being developed. The echelon pat tern of ore deposit continues at depth but is less pronounced, and the orebody is now more or less continuous over 2600 ft of strike length, with widths 5 ft to as high as 26 ft where overlapping of lenses occurs in one section of the mine. Better continuity of ore at depth has encouraged systematic mining and improved plant facilities to offset higher operating costs. With favorable persistence of ore at depth, the three-compartment No. 6 hoisting shaft appeared inadequate to handle increased tonnage from greater depths, and in 1952, a four-compartment steel and concrete shaft was started. This is now at a depth of 1906 ft, and shaft pockets and loading cartridges are being installed on the 1806 level. Ore from the new shaft, hoisted in 5 ½ -ton Jeto bottom dump skips, is dumped into a 500-ton shaft bin, from which it is fed to a 16x30-in. gyratory crusher and conveyed 415 ft through an undersurface concrete gallery to the secondary crusher and conveying system supplying the 900-ton mill. Lead, zinc, and pyrite concentrates are floated, and the flotation tailings are cyanided after desliming. Waste from the new shaft is dumped into a 250-ton surge bin, fed from this bin to a 24-in. conveyor, and discharged into the glory hole above the block cave. The new shaft is served by a double-drum 400-hp hoist used for ore and waste; the No. 6 shaft conveys men and material.

Jul 1, 1956

By P. F. Allen

With capacity of 51,000 tpd, the Morenci concentrator produces approximately 49,000 tons of tailing for final deposition. Disposal involves distrlbutlon of thickened tailing to dams in such a manner that solids can be used for dam construction and water can be impounded for reclamation. During early operation, although tonnage treated was lower, it was necessary to use orthodox disposal practices in the areas available for tailing. Trestles mounted on a series of dams, constructed of borrow material, carried the pipelines from which tailing were spigoted behind the dams. When adequate disposal areas were finally established, it became desirable to look for more efficient methods. The idea of placing the distribution pipe or manifold directly on the crest of the dam was advanced in 1945. After a period of testing, that procedure in modified form replaced the older trestle arrangement. Marked economies resulted, and time required to prepare dams for succeeding storage cycles was greatly reduced.

Jul 1, 1956

By E. S. Noe, D. S. Arnold, C. E. Polson

Reactors of today and tomorrow require a high uniformity of their fuel elements despite the wide variety of uranium raw materials from the far corners of the earth. To meet these quality standards metallurgists have been working to design production methods capable of yielding reactor feed materials whose maximum impurities are specified in parts per million, whose physical limits are expressed in thousands of an inch, and whose density variations are less than 1 pct. Such requirements are necessary to maintain normal neutron flow in the atomic reactor and to insure that the isotopic content of the feed material is maintained within narrow limits. Uranium ores and concentrates are produced in many sections of the world, including the Belgian Congo, South Africa, Australia, Canada, and the Colorado Plateau of the U. S. Ores from many of the larger deposits are relatively low grade, and these are concentrated near the mine site before shipment to refining centers, but high grade ores may be shipped directly to refineries.

Jun 1, 1956

Reducing Fusion: The impure or low grade uranium concentrate is mixed with a formulated flux of sodium carbonate, salt, and sawdust or fuel oil and heated, while being stirred, to about 950°C. This reduces the uranium to the black, water insoluble uranium dioxide and with the exception of nonamphoteric metals forms water soluble sodium salts of the vanadium, alumina, silica, phosphates, and other constituents of the cake. The cooled melt is then water leached, leaving a residue of black insoluble uranium dioxide. "Green Sludge" Digestion and Liquor Purification: The green sludge is redissolved in acid, and by selective precipitation involving pH adjustments and a final neutralization

Jun 1, 1956

By H. R. Steacy, A. H. Lang

Growth of general interest in uranium during the last ten years has been unparalleled in mining history, outranking the popular gold rushes and mining booms of bygone years. This is not surprising, considering the spectacular advances in nuclear research and the fact that a small amount of uranium can provide great quantities of energy for peaceful purposes. There are, however, a number of misconceptions and exaggerations regarding uranium. Many novices have highly exaggerated ideas of the ease of finding workable deposits, as opposed to mere occurrences, and reports of insignificant discoveries are sometimes given much publicity. Beginning about ten years ago mining for uranium has assumed a major place in Canadian and U. S. mineral industries. Uranium is now high on the list of metals produced in Canada. The gross value of uranium production in Canada in 1958, when additional plants now under construction are operating, will probably exceed 180 million dollars.

Jun 1, 1956

By Lloyd Williams, H. K. Gibbs, William L. Crentz, J. W. Miller

"Reserves This investigation shows that the Poplar Creek is the most important bed in Scott County from a production standpoint. Although the Poplar Creek bed contains the largest reserve, the Big Mary has a larger recoverable reserve. Estimates of reserves also have been made for the Pewee, Red Ash, Windrock, Upper Pioneer, Jellico, and White Oak beds.Known measured and indicated reserves of coal, based on a minimum bed thickness of 14 inches and on 1,800 short tons per acre-foot of coal in place, are estimated to be 143 million tons as of January 1, 1954. Of this total, 74 million tons is in beds 28 inches and more thick. Areas in each bed were omitted from the estimate because available data relative to the bed characteristics are too meager for making an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.Recoverable reserves of coal are estimated in beds 28 inches and more thick. This thickness is about the minimum now being mined by hand loading onto conveyors in the Appalachian region. The weighted average recovery for all beds in Scott County, as determined by this investigation, is 52.4 percent. This percentage is based on the total thickness of coal in the bed (less partings three-eighths inch or more thick) rather than on the thickness of the coal mined. Based on the weighted average percentage of recovery for all beds in Scott County, the recoverable reserves of coal are estimated to be 39 million tons as of January 1, 1954.Coal Analyses Chemical analyses of coal samples taken for this study show that the coal in Scott County is of high-volatile a bituminous rank except the Upper Pioneer bed, which is shown to be high-volatile B bituminous. The Pewee bed shows typical low-sulfur characteristics. The high ash and sulfur in the Big Mary are characteristic of that bed. The Poplar Creek is moderately low in ash and sulfur in areas where there is no parting in the bed."

Jun 1, 1956

By S. C. Sun, D. R. Mitchell

Experiments show that ores such as tungsten and tin, which slime excessively, can be deslimed and upgraded by ultrasonics. The method proposed depends primarily upon the stratifying and peptizing action caused when high frequency sound waves are propagated upward through ore pulp in a cylinder tube. Stratifying and peptizing are somewhat hindered by the accumulating action, which embodies additional effects of reflection and refraction.

Jun 1, 1956

By C. H. Reynolds, Robert C. Pruess

Late in 1954 exploratory drilling indicated a substantial orebody on the Rattlesnake claims of Woodmont Inc., a Continental Uranium Inc. subsidiary. Woodmont holdings are located about 35 miles southeast of Moab, Utah. Only a few miles north of Big Indian Valley and other Chinle-sand uraninite deposits, the claims are in an entirely different geologic environment. Detailed development drilling continued until the Deep North orebody was outlined, covering an area approximately 300 x 450 ft. All exploratory drilling and about 80 pct of development drilling was wet core. Chemical assays for each hole sample, applied at 1-ft intervals against the measured core length, were put into a conventional ore calculation formula. Forty-six holes were drilled to delineate the Deep North orebody.

Jun 1, 1956

By Franc R. Joubin, D. H. James

Uranium exploration in the North Shore area of Lake Huron goes back to 1847 when J. L. LeConte, a distinguished American geologist, identified a pitchblende-like mineral which he called coracite from specimens sent from a locality north of Sault Ste. Marie. In 1948 a search for the LeConte occurrence resulted in discovery of the Camray field, some 70 miles north of Sault Ste. Marie. Prospecting the Camray field yielded about 30 pitchblende occurrences spread over approximately 200 sq miles. Almost without exception these discoveries consisted of narrow, short, pitchblende-filled fractures, within or along the contacts of diabase dykes cutting pre-Cambrian Archean granite and gneiss. Eight discoveries were diamond drilled and three were explored underground, but none proved to be of economic value. Uranium prospecting at this time spread far afield, and it was in 1949 that radioactive conglomerate was discovered in Long Township of the Algoma district midway between and 90 miles from Sault Ste. Marie and Sudbury. F. Joubin examined this discovery at that time but could not interest capital in its development.

Jun 1, 1956

By D. A. Reynolds, R. G. Travis, James J. Dowd, R. F. Abernethy

"1. Reserve estimates have been made for eight coal beds in Monongalia County, W.Va., but only the Pittsburgh, Sewickley, and Upper Freeport beds are important at this time. The Pittsburgh, Sewickley, Waynesburg, and Upper Freeport beds contain the largest recoverable reserves.2. Known measured and indicated reserves in all beds, based on a minimum thickness of 14 inches and 1,800 short tons per acre-foot of coal in place, are estimated at 3,526 million tons as of January 1, 1954. Of this total, 3,294 mil¬lion tons is in beds 28 inches and more thick. Areas in each bed except the Pittsburgh were omitted from the estimate because available data relative to the bed characteristics are too meager for making an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.3. Recoverable reserves of coal have been estimated in beds 28 inches and more thick. This thickness is about the minimum now being mined by hand loading onto conveyors in the Appalachian region. The weighted average recovery for all beds in Monongalia County, as determined by this investigation, is 47.9 percent. This percentage is based on the total thickness of coal (less partings three-eighths inch thick or more) in the bed rather than on the thickness of the coal mined. Based on the weighted average percentage of recovery for all beds in Monongalia County, the recoverable reserves are estimated at 1,577 million tons as of January 1, 1954.4. Monongalia County coals of the major producing beds are of high-volatile a bituminous rank.5. The Pittsburgh and Lower Freeport beds in this county yield coal that can be used as metallurgical coal, especially when blended with low-volatile coals. The Lower Freeport coal is coked singly and in beehive ovens, and makes good metallurgical coke.INTRODUCTIONThe investigation to evaluate the reserves of coking coal was planned to cover three phases: (1) Estimation of known measured and indicated recoverable reserves of all coking coal; (2) study of methods of upgrading marginal coals through effective preparation; and (3) study of carbonizing properties of coals and coal blends not now widely used for metallurgical coke making."

Jun 1, 1956

By James M. Schopf

Coal petrology is the study of the lithologic composition and texture of coal and includes megascopic as well as microscopic differentiation. Coal petrography is a quantitative study, principally (but not exclusively) microscopical in nature. The distinction between coal petrologic and coal petrographic studies usually is not important, but it is important to recognize that these studies differ materially from other types of petrology that deal primarily with minerals. The petrologic entities of coal are less clearly distinguished than most minerals and the basis of distinction is not always clearly expressed. The relation of coal petrology to geologic, mining, and technologic problems is most evident when results of coal petrologic studies can be stated quantitatively. The chemical and physical composition of coal and the determination of its quality and properties are continuing problems. The source of these problems lies in the heterogeneity of coal and in its almost complete insolubility in ordinary solvents at normal temperatures.

Jun 1, 1956

By William L. Lennemann

Chemistry of uranium with respect to its hydrometallurgical recovery from carnotite ores was investigated and well defined during the radium boom period between 1900 and 1920. Since that time, methods used to extract uranium from its ores have remained basically either acid leaching or sodium carbonate leaching. Until about 1950, the only practical methods known for achieving a better than 75 pct U2O3 concentrate from the leach liquors involved fundamental chemical techniques for either purifying a solution prior to the uranium precipitation, or refining a crude uranium concentrate that was produced by neutralizing a pregnant mill liquor.

Jun 1, 1956

By James Boyd

All mining and milling enterprises must be based on adequate ore reserves. Reserves must be established by physical exploration, and the orebody should be of sufficient size and grade to insure recovery of capital invested in mine purchase, development, and mill construction and to provide a reasonable profit. Determination of these economic factors is so complicated, and present costs of mine development and construction so great, that analysis can be made only by competent persons qualified by experience in this field. What rate for maximum efficiency? Unfortunately, even today mills are built before deposits have been adequately outlined, and there are rusting monuments to such folly in nearly every mining region. Also there is a tendency to be guided by the philosophy that "if a little is good, a lot is better," which leads to the conclusion that mining at a given rate and making so much per ton will yield a profit of so many dollars per day. Consequently, why not build a mill to treat twice as much per day and make twice as much money?

Jun 1, 1956

By Patrick H. O’Neill

The Choco placers, mined continuously since the earliest expeditions of the Spanish conquistadors, were exploited by the Indians prior to the conquest. Platinum is found in varying percentages with gold throughout the Choco placers and is found in minor percentages in some placers in other parts of Colombia. The Choco Department is on the west coast of Colombia between the western range of the Andes and the Pacific Ocean and extends from the San Juan River north beyond Panama to the Caribbean. The first reference in European literature to platinum was by Julius Caesar Scaliger in 1557. He did not assign any name to it but referred to it as an infusible metal found in the mines in the New World. The Spaniards had given it the name platina, which is the diminutive for plata, the Spanish word for silver. Don Antonio de Ulloa first recorded the name while on an official visit to the Choco from Spain in 1735.

May 1, 1956