Search Documents

By R. C. Weed

LEACHING in place at Cananea began in the 1920's on a limited scale. The first plants were small wooden boxes located underground in the Capote and Oversight mines, and output was low. Scrap iron was used as precipitant. Later several other small plants were started up. Leaching was limited entirely to underground areas, and production remained low. The Veta precipitating plant, the first on a larger scale, was put into operation in the late 1920's. After a period of intermittent service it was rebuilt in 1946 and has since been running continuously. In 1943 work on the Colorada open pit was started. This produced 40 million tons of waste, which averaged 0.20 pct capper. When these dumps had aged a few years it was decided to leach them on a large scale, and after considerable research and investigation a leaching system of pumps and pipelines was laid out and installed. At the same time the Ron-quillo precipitation plant was built to treat the copper solutions from the pit dumps. This plant started operation in March 1953. Leaching areas consist of the Colorada pit dumps and various mined out and caved underground stopes. The principal mineral, chalcocite, leaches readily in a weak sulfuric acid solution containing ferric iron. Enough pyrite is contained in the areas to produce an acid-ferric iron solution strong enough to dissolve the copper. Each area is studied to determine the best method of distributing the water over it and the best method of collecting the copper-bearing solutions after leaching has taken place. Water is generally distributed by means of ponds, ditches, and sprays. Spraying has proved the best method of spreading the water evenly; however, in a dry climate some water is lost through evaporation. After passing through the leachable material the solution is collected underground by dams and bulkheads and on surface by dams. An effort is made to give the maximum storage capacity practicable.

Jan 1, 1957

By Fitterer, G. R.

The impact of the work of Herty "et al" on modern liquid steel technology can only be evaluated by first setting the stage as it existed in 1926. It is important to briefly review not only the steel making process and viewpoints regarding methods of refining, but also to describe the tools which were available for research at the time. One must recall that only 15 years before the beginning of this program, the open hearth production exceeded that of the Bessemer in the United States. Many open hearths were still operating on producer gas (a very inefficient fuel), although some plants were converting to the use of natural gas and very few to oil. Continuous rolling of wide strip started this year. The Faraday Society in England held a World Conference on Physical Chemistry in Steel Making in 1925 and the contributions to this work created considerable interest throughout the world and it appeared that physical chemistry might convert the art of steel making into a science. These papers, however, attempted to solve the problems through the use of the older physical chemical concepts such as Nernst's numbers, etc. and considerable data were missing. In 1923, Lewis and Randall had published their book Thermodynanzicsl and this was later to establish and standardize the steps which are now accepted for the calculation of physico-chemical equations. At the time this research work was started, there were no small high frequency induction furnaces. Northrup had just invented his high frequency furnace and a few large units had been instilled in plants. The vacuum fusion method lor the determination of oxygen in steel was

Jan 1, 1957

By G. S. Hume

FOR MANY YEARS Canada lived in the hope of attaining a substantial production of petroleum and natural gas that, to geologists familiar with the sedimentary basins of this country, seemed an entirely reasonable expectation. There have been surges of exploration activity stimulated by oil and gas discoveries and development such as occurred in Turner Valley. However, it was not until the Leduc field in Alberta was found in 1947, and the significance of that discovery was realized, that the search became really intensive and continuons. Expansion now has become a matter-of-fact attitude based on results which would have been considered impossible of achievement a few years ago.

Jan 1, 1957

The Rocky Mountain Coal Mining Institute Mr. John Peperakis, President Dear Mr. Peperokis: Following is the report of the Treasurer from May 19, 1956 to May 3 1, 1957: RECEIPTS [Cash on hand May 19, 1956. ................................... $2,209.64 Dues ........................................ $ 810.00 Registrations, Banquet, Tickets, etc. 1,992.75 Contributions ................... ............ 1,490.00 Interest .................................... 27.60 4,320.35 $6,529.99]

Jan 1, 1957

By C. M. McKinney

This report contains Bureau of Mines routine analyses of 492 samples of crude petroleum from 470 United States oilfields, each of which produced 2,500 barrels a day or more during at least 1 of the years 1946-56. The fields are listed alphabetically by State and field names in table 1, with information on the geographical and geological sources of the samples. Table 2 summarizes the general characteristics of the crude oils and analytical and computed data determined from the analyses. A previous report 4 contains similar analyses of 283 important United States oilfields; some of them are repeated in this report. Many fields for which analyses previously were published are represented by new analyses, which include data not previously reported. Refractive index nu and specific dispersion, ng minus nD divided by the density, for some of the distillate fractions are included in the analyses of 316 of the crude-oil samples. This is the first Bureau of Mines report on analysis of crude oils to contain such data, and their use in calculating hydrocarbon-type composition of the fractions is explained.

Jan 1, 1957

By Eleanor Abshire

This bibliography is the result of a cooperative project undertaken by the Bureau of Ships and the Bureau of Mines to accumulate literature published to date on zirconium and hafnium and to establish an information center on these metals for the use of any interested research organization or library. This bibliography, which will be supplemented as additional information is accumulated, consists of references, with abstracts, to pertinent literature on the subject published from 1907 to date.

Jan 1, 1957

By John A. Emery, Frank G. Snyder

Mining geology has a threefold objective: to guide prospecting for new ore, to evaluate known orebodies as development risks, and to supply the detailed knowledge of ore structures necessary for more economical extraction. The role of geology in exploration is well established. This article will deal solely with orebody evaluation and the application of geology to development and mining problems as practiced by St. Joseph Lead Co. in the southeast Missouri district, which for many years has supplied approximately 30 pct of U. S. lead production. The primary concern of the present discussion is geology in the district, not geology of the district. The southeast Missouri district, locally called the Lead Belt, includes parts of St. Francois, Madison, and Washington counties. The first recorded mining was about 1720 at Mine La Motte in Madison County on surface showings of lead ore. Later discoveries near Bonne Terre, twenty-five miles to the north, led to extensive prospecting and underground mining. To date the district has yielded well over 8 million tons of pig lead, valued at more than $1 billion. By far the greater part of the lead production has come from an area of 50 sq miles, centering Fig. 1-Central portion of southeast Missouri on the city of Flat River, as shown in Fig. 1.

Dec 1, 1956

By Bernard Rachlin

In the mineral industry measurement of density or specific gravity of slurries is often necessary or highly desirable. To date the most successful method of measuring the specific gravity of various media is to hand weigh a constant volume sample of the slurry. This method is time-consuming, however, and is intermittent rather than continuous. Most density measuring instruments in use today are variations of three basic systems: air bubble tube systems, radioactive methods, and displacer systems. The high cost of the radioactive cell, combined with the precision electronic measuring that is required, limits the practical utility of this procedure to a small percentage of critical processes. In the air bubble systems clogging of the bubble tubes with solids has rendered this type of measurement completely ineffectual for many applications. Continuous or intermittent purging of the bubble tubes with air or water to prevent tube clogging has been tried but has not been very successful, especially in the heavy media process.

Dec 1, 1956

By Laurence W. Casteel

Indian Creek Mine, newest of the St. Joseph Lead Co. properties, is located in southeast Missouri on the flanks of a buried porphyry ridge. Here the orebodies are very irregular in size and shape and have a regional pitch of about 15°, which may vary locally from 0 to 90°. To maintain an economical grade of ore, selective mining is imperative. The room and casual pillar method is employed with 20-ft diam pillars 35 ft apart where possible. Stopes vary in height from 10 to 55 ft. All are too small to supply a loading unit continuously.

Dec 1, 1956

By W. H. Wamsley

Used in combination with conveyor belt haulage, bucket wheel excavators offer unusual possibilities for low excavation and haulage costs. Originating in Germany, these machines are now in use or on order for Australia, Northern Rhodesia, the Belgian Congo, Italy, Yugoslavia, France, Belgium, Indonesia, and the Union of South Africa. A diamond mine in South Africa that has been using German bucket wheel excavators since 1928 purchased American cable-way excavators and American scraping equipment after the war. Operating cost for this equipment was double that for the bucket wheel machines operating in the same mines with crawler-mounted stackers. Machines built and operated in the U. S. are, as far as the writer knows, confined to the northern Illinois coal field, where they are used in conjunction with large shovels to strip overburden too high to be reached by the 30 to 40-yd shovels. Their long stacker belts can deposit the spoil far enough behind the coal face to avoid slides, in such a manner as to make reclaiming the land easier. These large, specialized machines are now being made by Bucyrus-Erie Co. but are not adaptable to many open pit mining situations.

Dec 1, 1956

By J. P. Zannaras

If we assume that testing of the model started at time C, that time t2 was the instant at which the elastic limit of the material was passed at the points of the maximum stress, and that at time t3 the failure of the model was completed as shown in the typical photograph (Fig. 1), then actually the photograph shows the final results of what took place between time t2 and t3. By the principle of similitude all conclusions drawn from the behavior of the model were applicable and valid for actual mine roofs up to the time t, after time t, motions and friction came into play during the destruction of the model. The events between t2 and t3 and the photograph itself are not representative of the events expected in an actual mine roof unless corrections imposed by the principle of similitude are made.

Dec 1, 1956

By J. R. Dawson, J. A. Glunt

Vesta No. 4 and 5 mines supply most of the high volatile coal required for Jones & Laughlin's by-product coke plants. Until 1944 all coal produced in these mines was loaded by hand. Pressure to mechanize at Vesta was brought on by the manpower shortage in World War II, and in 1943 a decision was made to change to mechanical loading. It was the opinion of those concerned that by use of selective mining the coal would be clean enough to be processed by the existing preparation plants. At that time coal cleaning at Jones & Laughlin consisted of hand picking the larger sizes at the mine tipples and wet washing at plants located at the Pittsburgh and Aliquippa Works. A typical section of the Pittsburgh seam as it occurs at Vesta is shown in Fig. 1. The 14 to 16 in. of drawslate immediately over the coal is too soft to be used for roof and must be taken down, leaving the rooster coal just above for roof. In selective mining an attempt is made to mine the coal under the drawslate first and then load out the drawslate separately as refuse. In full seam mining slate and coal are shot down at the same time and loaded out.

Dec 1, 1956

By Eldred D. Wilson

Apropos of metals low in the series illustrated by Dr. Butler's Table II, it is interesting to note that Cress and Feldman reported traces of platinum metals in several samples of alunite. They found, chemically and spectrographically, several traces of platinum, palladium, and rhodium in alunite from Sugar Loaf Peak, near Quartzite, Ariz.; silver, platinum, and rhodium in alunite from Rio Grande County, Colorado; and traces of rubidium and gallium in various samples of alunite. These authors stated that the platinum metals appear to be present as oxides and suggested deposition by hydrothermal solutions under near-surface conditions.

Dec 1, 1956

By R. R. Hartman, W. B. Agocs

In the course of a return flight from Olympia, Wash., to Laramie, Wyo., an airborne magnetometer profile was recorded continuously. The level of flight was controlled at barometric levels along segments of the flight. Barometric altitude was changed from 3000 ft to a maximum of 12,000 ft above mean sea level to take care of topographic variations. Terrain clearance varied from 800 to 7300 ft. Horizontal positions were obtained by recording and tying to cities, towns, airports, river crossings, and other landmarks in the course of the flight. Figs. 1-6 show the course of the flight and the general geologic and tectonic features traversed. The flight line begins south of Olympia, Wash., and proceeds south across the Puget-Willemette depression to the Columbia River. Thence it proceeds eastward along the Washington-Oregon border across the Cascade Mts. and lava flows and the Umatilla basin to Pendleton, Ore. From Pendleton it traverses the Blue Mts. uplift of Oregon in a southeasterly direction, and then to the Boise basin of southwestern Idaho. The flight line swings in an easterly direction as it passes over the Snake River downwarp to the south of the Idaho batholith. It then passes over the northern portion of the Great Basin and the heavily overthrust area at the intersection of the Utah, Idaho, and Wyoming borders. The flight then assumes an easterly course to cross the series of basins and uplifts of southern Wyoming and terminates near the western flank of the Laramie uplift.

Dec 1, 1956

By R. I. Williams

Kennecott Copper's mining activities in Arizona are conducted by the Ray Mines Div., located in Ray, Ariz., in the Mineral Creek mining district about 60 miles southeast of Phoenix. The Ray orebody lies in a mineralized zone belted on the east, west, and north by well defined faults. The orebody consists principally of schist with intrusions of quartz porphyry and diabase. The dominant ore mineral in the schist and quartz porphyry is chalcocite, with some native copper, and in most areas the orebody has been heavily oxidized. In the diabase the dominant ore mineral is chalcopyrite. Ore deposition in the schist portion is very erratic, with no apparent structural explanation. In 1873 silver prospectors opened the mining district, but it was not until 1899 that an English company made the first major attempt to exploit the copper deposits. This venture failed because of improper sampling and limited development work. In 1904 D. C. Jackling, Seeley Mudd, and Philip Weiseman became interested in the Ray Copper Co. and the Gila Copper Co., which later merged as Ray Consolidated Copper Co. In 1926 the Nevada Consolidated Copper Co. took over Ray Consolidated and in turn was taken over by Kennecott Copper Corp. in 1933. The extensive program of surface and underground development and exploration begun in 1907 continued through successive changes of management and ownership to the present time.

Dec 1, 1956

By H. Herbert Hughes

In the years following World War II, L. de Roll S.A., Zurich, Switzerland, perfected its vertical kiln. De Roll first became interested in cement-manufacturing equipment in 1947, not only kilns but also the crushing, grinding, and handling equipment required for a complete cement plant. The parent company, Louis de Roll Iron Works, S.A., Gerlafingen, Switzerland, was founded in 1804. In its six plants, and with its associated companies, de Roll manufactures and installs equipment for a wide variety of industries-chemical and metallurgical operations, fats and oils plants, and municipal refuse incinerators and sewage disposal installations. Vertical shaft kilns, of course, are as old as Portland cement itself. Their fuel economy has long been recognized, particularly in Europe where fuel costs are high. But the disadvantages of old-type shaft kilns have been the lack of consistent quality of the clinker, the small capacity, and the relatively high labor costs.

Dec 1, 1956

By Robert F. Love

Deep under the hills of southwestern Wyoming lies a nonmetallic mineral deposit of incredible dimensions and value. This nearly pure, horizontal bed of the mineral trona, a sodium sesquicarbonate (Na2HC0,.NaHC08.H20), is found in the Green River formation some 1500 ft below surface. It is believed that evaporation of an ancient saline lake left this sodium carbonate as the evaporite and mysteriously left practically no sodium chloride, which is the common constituent of an evaporated saline lake. The trona bed averages 10 ft in thickness and extends over an area of several hundred square miles. In 1938 a geologist with the U. S. Geological Survey identified the trona in the core from a former oil exploration drillhole. By so doing, he initiated the developments of a chemical industry of impressive growth in the area, an industry on the threshold of further and much more spectacular growth. A drilling program by the Union Pacific Rd. and Intermountain Chemical Co. in the early 1940's succeeded in blocking out mineable reserves of several hundred million tons. Development of the deposit started in 1946 with the sinking of a 12-ft diam, concrete-lined shaft 1500 ft deep-followed by construction of a small pilot calcining plant. Actual mining of the trona started in 1947 and continued on a limited scale until 1953, when the $15 million surface facilities were completed, along with the second shaft and other expanded underground facilities. Since April 1953 the mine has been producing more than half a million tons per year, from which the refining plant has produced more than 300,000 tons per year of high quality soda ash.

Dec 1, 1956

By T. M. Berry

In the past few years changes have taken place in shaft sinking. Progress has been made with types of machinery designed, developed, and made available to shaft sinking contractors. This is particularly true of drilling and mucking equipment. Compared with conventional clamshell loading, mucking or loading with a crawler-mounted overshot loader is a new technique for shaft work. There are several methods of clamshell loading. Dravo Construction Co. mounts an air tugger on the clamshell to operate the closing line. The load, or holding line, is attached to the hoist of a crane or whirler at the shaft collar. The clamshell is raised or lowered by the hoist when a signal is given by a bell or light system operated by men at the bottom of the shaft. Two men control the drift of the clamshell with tag lines, pulling it to any position in the shaft for loading, or over the shaft muck bucket for emptying. One man operates the air tugger to open and close the clamshell by means of two lines attached to the operating air valve, just as reins are used to drive a horse. One man operates the signal telling the hoist operator when to raise or lower the clamshell. This method requires two hoisting lines in the shaft-the line from the mine hoist that lifts

Dec 1, 1956

By Dale I. Hayes

Combined loader and transport, the Gismo is now built for sale in one size, 5 to 6 tons. It will operate in a minimum opening of 7x7 ft and can be built to operate at lower heights. Where space limitations are not a factor it could be designed with much greater carrying capacity-12, 18, or 25 tons-to be powered with a standard heavier tractor. The Gismo is mounted on crawler tracks of the same design as the tracks of the small Allis- Chalmers HD-6B tractor used to power it. With the HD-6B tractor it will negotiate upgrades of 12 pct and downgrades of 20 pct. The next tractor size would make the device feasible for steeper grades or for a machine of larger capacity at moderate grades.

Dec 1, 1956

By A. R. Sims

Are from the Greater Butte Project is hoisted through the new Kelley shaft. In 1946 when plans were formulated for the Kelley mine, two test cave blocks were mined by using the facilities of the old St. Lawrence mine. These blocks, known as the Adams No. 1 and Adams No. 2, produced more than half a million tons of ore. The experiment proved beyond all doubt that cave mining was possible- and economical-in Butte. Adams No. 1 was patterned after Inspiration cave blocks. Adams No. 2 was a slusher type, with the slusher lane on the first floor above the haulage crosscut and at right angles to it. Thirty-horsepower electric hoists slushed ore from 48-in. scraper buckets directly into cars for haulage to the shaft. These cars were the 57-cu ft Granby type hauled by 6-ton battery locomotives over 40-lb, 18-in. gage track. Prior to this time the largest slushing machines used at Butte were 15-hp electric hoists pulling 36-in. scrapers.

Dec 1, 1956