Search Documents

By G. G. Priest, B. E. Morgan

The production of oil and gas from wells is often seriously hindered by the compaction of solids in the perforations during the perforating process. To realize the full productive capacity of a well, it is necessary either to remove the plugging material from the perforations or to perforate in a manner which does not cause plugging of the perforations. The latter method can be accomplished by having a non-plugging fluid in the casing at the time the well is perforated. This paper describes the results of laboratory tests, perforating tests, and experimental field tests which demonstrate that certain emulsions serve effectively as non-plugging perforating fluids. The principal components of these emulsions are two liquids: an aqueous phase consisting of a solution of either sodium chloride or calcium chloride, and an oil phase consisting of diesel oil, tetrachloroethylene, or a combination of both. Small amounts of other agents which serve to stubilize the emulsions, to reduce the fluid loss, and to inhibit corrosion are also present. The density of the emulsions is controllable within the range of 7.5 to 12.5 lb/gal; no insoluble solids are present, the filtration rate is low, and the thermal stability is satisfactory at temperatures as high as 200°F. The corrosion of steel by these emulsions is negligible. Tests conducted under conditions which simulate the temperature and the pressure in an actual well demonstrate that these emulsions fulfill the requirements of a non-plugging perforating fluid. In addition, lirnited field experience furnishes evidence that these emulsions remain in position after they are spotted, that they are retained in the casing after the perforations are made, and that they are easily removed from the perforations when the well is opened for production. When the pressure in the borehole is greater than the formation pressure at the time a well is perforated, plugging of the perforations can be avoided by spotting an emulsion adjacent the interval to be perforated. This procedure should eliminate low well productivity caused by plugging the perforations. INTRODUCTION Nature of Problem The most widely used method for the completion of oil and gas wells is to set and cement casing through productive horizons, and then to obtain production by gun-perforating the section of casing opposite the desired interval. This method is gen- erally successful and it was thought at one time that those failures which did occur were due to insufficient penetration by the perforator. Despite recent improvements in perforators which assure ample penetration, unsatisfactory fluid production continues to be a problem. Evidently, the trouble comes from some other source. Recent results obtained by Allen and Worzel1 demonstrated that low fluid productivity may be caused by the perforating process and/or by the fluid in the wellbore at the time of shooting. They found that perforations are often completely plugged by debris from the perforator, pulverized sand from the formation, and compacted solids from the drilling mud when the pressure in the wellbore is greater than the pressure in the formation at the time of perforation. In some cases a differential pressure in excess of 400 psi was required to initiate flow into the well through these plugged perforations. The plugging of perforations by solids not only causes low productivity from wells, but it creates simultaneously other problems in the production of oil and gas. For example, when most of the perforations are plugged, high rates of flow must occur through the few perforations that are open. The resulting high pressure drop may cause production

Jan 1, 1958

By John H. Nicholls

In this paper, Imperial Oil Limited reports briefly on the drilling by contract rigs of twenty-nine slim holes in the Virden, Smiley, and Souris Valley areas. The investigations showed that slim-hole penetration rates, as a result of careful control of drilling variables, can approach those achieved with 7 7/8-inch bits. It is concluded that slim-hole drilling is acceptable for development or exploratory work. Imperial also reports on the completion techniques and equipment that have been developed on twenty-seven tubingless 2 1/2-inch casing completions. Indications are that the method is economically desirable where excessive gas or water production is not anticipated.

Jan 1, 1958

By R. E. Lund, D. E. Warnes

SELECTIVE sulfation of individual constituents in ores or metalliferous products has received increased attention in recent years. The fluid-bed reactor with its advantages of close control of both temperature and atmosphere promises to have ap-

Jan 1, 1958

By Hsun Hu

NOT much data are available in the literature on textures in cross-rolled metal sheets. Among the body-centered-cubic metals, a few investigators have studied the preferred orientations developed in cross-rolled and in subsequently annealed molybdenum specimens.1-4 Semchyshen and Timmons5 onstructed complete pole figures for the cross-rolled and subsequently annealed arc-cast molybdenum. They used the conventional photographic method. Similar data on cross-rolled iron are still lacking. In view of the fundamental importance of iron as a basic metal for magnetic alloys and many industrial steels, the present investigation was undertaken in an attempt to understand more about its properties. The material selected for the present work was of high purity, and the textures were determined by the Geiger counter spectrometer technique, which permits the construction of quantitative pole figures. Experimental Procedure The material used for this investigation was NRC (National Research Corp.) high-purity, gas-free iron. The total gas content (N2 + O2 + H2) given was less than 0.026 pct, and the carbon content, less than 0.005 pct. Spectrographic analysis of a 2 in. cast ingot showed the percentage of metallic impurities as 0.0004 pct Cu, 0.0002 pct Mg, 0.001 pct Mn, 0.01 pct Ni, and 0.006 pct Si. A 1 in. thick slice was cut off from the 2 in. cast ingot. It was hot-forged at 850 °C to destroy most of the cast structure. Surface scale was removed by milling the forged piece to a size 2 in. long, 1½ in. wide, and ¾ in. thick. After normalizing at 915 °C for 15 min, the piece was alternately cold-rolled 40 pct and annealed at 750°C in hydrogen to a final thickness of 0.165 in., with a resulting uniform grain size of 0.1 mm.

Jan 1, 1958

By A. A. Berk

LAGGING technology and the slow spread of information have been the chief obstacles to widespread participation in minimizing the industrial pollution load. These obstacles can be conquered by fact finding and applied research. There are three aspects to the problem of water-borne mineral waste: to minimize the amount being thrown away, to select a predisposal treatment, and to use the products or dispose of them. It is often possible to minimize the waste by making very minor changes in the process that produces it. For example, a manufacturer of automobile bumpers greatly reduced the dragout 'from a plating bath by modifying the design and position of two boltholes.' A plater of automobile hubcaps installed a drainage bar and decreased the loss of chrome-plating solution to the rinse water by about 80 pct.' The mill at a western mine found it possible to discard 60 to 70 pct of an ore with minimum treatment," so that the processing effort could be concentrated on a high-graded slime, with significant reduction in costs and improvement in recovery. The possibilities for waste reduction through process changes are limited only by the imagination. A recent patent points out the advantages of using No. 1 fuel oil instead of water in wet-process cement making;& the fuel oil presumably has better properties than water for this purpose and is said to be almost com'pletely recovered or utilized, so that there is no waterborne waste. Recycling to reduce wastes and improve process economy is very well illustrated in vanadium and uranium recoveries from relatively low grade ore. Ores containing 6 pct calcium carbonate were found to give poor vanadium recovery by the salt-roasting process because the vanadium was converted to water-insoluble calcium vanadate. Following the salt-roasting process, sulfuric acid was used to leach the uranium. Enough calcium sulfate was formed

Jan 1, 1958

By James E. Berryman

A method is presented for calculating the pressure depletion performance of a gas-condensate reservoir from the original reservoir fluid composition using the laboratory determined pressure-production history and retrograde liquid accumulation as guides. Equilibrium vaporization ratios for this calculation were modified from published data until the calculated dew point pressure and retrograde liquid accumulation agreed with the values observed in the laboratory. The calculated results are compared with the produced gas composition determined by low temperature analysis during constant volume laboratory experiments of pressure depletion behavior. This comparison shows that the calculation procedure is adequate for determination of gas phase composition. Data from field separation tests in low temperature separators are presented which verify the applicability of published equilibrium vaporization ratios for a wide range of separator conditions. INTRODUCTION A reliable prediction of the pressure depletion performance of a gas-condensate reservoir is necessary in determining reserves and evaluating field separation methods. The predicted performance is also used in planning future operations and studying the economics of projects for increasing liquid recovery. Because the flow of fluid in a volumetric gas-condensate reservoir is usually single phase flow, the pressure-depletion per-formake is primarily a function of the phase behavior of the reservoir fluid. The properties of a gas-condensate system of major importance are: (1) compressibility factor at reservoir temperature and pressure; (2) dew point pressure; (3) composition changes of the vapor phase with pressure depletion; (4) recovery of original in-place hydrocarbons at any pressure; and (5) retrograde condensate accumulation. These properties are most generally determined by a pressure depletion-type experiment on recombined separator gas and liquid samples in the laboratory. ldeally the pressure-depletion performance can be calculated from the composition of the original reservoir fluid if the reservoir temperature and initial pressure are known.1,2,3 It has been reported "... comparison of such computations with depletion-type ex-periments on recombined samples in the laboratory have yielded results that appeared to be entirely adequate.". The success of such calculations is determined by the equilibrium vaporization ratios chosen, especially those for the higher boiling point hydrocarbons. It is the purpose of this paper to present a method for computing the change in composition of the vapor phase during pressure depletion by production using laboratory determined properties of the system to guide the calculation and to illustrate the use of the method with data from the Cockfield "D" sand of Washington field, St. Landry Parish, La. Results of field tests and laboratory analysis are included. As a result of this reservoir fluid study, a cycling program has been evaluated, the fidd has been unitized, and the cycling started in July, 1956.

Jan 1, 1958

By F. W. Smith

To determine whether preheating coals before carbonization would improve the coking properties of the coals, particularly the weaker coking coals, 3 coals, 1 each from Illinois, Kentucky, and Pennsylvania, and a blend of the Illinois with a Pocahontas coal were preheated before testing for coking properties in the Bureau's BM-AGA pilot oven. The effects of preheating on the chemical and physical proper-ties of the coals and on the yields of carbonization products and strength of the coke produced from the preheated coals were determined, as were also the effects of bulk density, gaseous atmosphere, and residence time during preheating. Most benefit from preheating was found with weaker or oxidized coking coals, whereas the more strongly coking coals and blends showed little effect. Direct charging of preheated coal to the coke oven without cooling gave better coke, increased yield of tar, and decreased yield of gas. INTRODUCTION Although 94 percent of today's coal production comes from fields east of the Mississippi, the Eastern States have only about one-third of the Nation's recoverable reserves. West Virginia, which now produces more than any other State, has much smaller reserves than Utah, Colorado, and Wyoming.5/ However, the manufacture of iron and steel in Western States, which has increased greatly since World War I, is handicapped by the scarcity of high-grade coking coals, such as are plentiful in the Appalachian region. Unless a practical method of improving the cokemaking property of local coals is developed, ferrous metallurgical industries in the West must continue to use inferior coking coals and to pay high shipping charges for better coals.

Jan 1, 1958

By J. D. Livingston, Bruce Chalmers, R. L. Fleischer, R. S. Davis

INTERACTION of dislocations on intersecting slip planes has long been considered a primary cause of work hardening in metals. Easy glide and low work-hardening rates have been observed experimentally only when single-crystal specimens were oriented so that one slip plane was initially favored. When single-crystal specimens have been oriented so that initially two or more slip planes were equally favored, high initial work-hardening rates have been observed. In a polycrsstalline aggregate, glide on five systems is in general necessary for a crystal to deform in conformity with the change in the shape imposed by the other crystals.* Only a small fraction of the crystals of a polycrystal will be oriented so that two

Jan 1, 1958

By F. R. Archibald

A STATEMENT on this subject by A. D. Turnbull, presented and discussed at the Annual Business Conference of the Metallurgy Division, C.I.M., held in Ottawa on April 22nd 1957, led to creation of a committee "too see if the Metallurgy Division of the C.I.M. can improve this situation". Without discounting the general problems of education and short-ages in other fields, the committee is primarily concerned with deficiencies related to metallurgy. The committee members are: F. R. Archibald, Chairman, A. D. Turnbull, L. E. Djingheuzian, J. U. Mac-Ewan, and L. M. Pidgeon. Following exchange of views among the committee members a general attitude of approach was established and a background of reference material assembled. It is the purpose of this review to acquaint those interested with the reference material, to offer an appraisal of the situation, and to suggest a programme for action by the Metallurgy Division of the C.I.M. Before proceeding with the ?presentation it is fitting to point out that, notwithstanding some rather important developments in public concern for educational matters, as well as changes in the level of activity in the metallurgical industry, the statement (April 1957) by Mr. Turnbull still stands as a sound article of reference.

Jan 1, 1958

By P. Sanchez-Mejorada

GEOLOGISTS who are acquainted with the mines of northeastern Mexico realize that the most important lead-silver replacement deposits of the province are confined to a single formation. But since the formation is several hundred meters thick, the author has determined the relative position of the lead mantos in the belief that this information will prove useful in the search for new mines. This article describes the stratigraphic location of lead-silver replacement deposits known in several mines situated in a region comprising part of the states of Coahuila and Nuevo Leon. The area studied extends for 200 km* (125 miles) from east to west and 70 km (45 miles) north to south.

Jan 1, 1958

By Oliver Bowles

The term "stone" in its broader sense includes not only the well-known limestone, marble, granite, sandstone, and slate but also precious and semi precious stones and many minerals and rocks not included in the principal groups. Stones have long been used for structural and ornamental purposes. To be so used, they must be cut to various shapes and sizes, and some must be polished to bring out their inherent attractiveness.

Jan 1, 1958

By J. H. Wernick, D. Dorsi, K. E. Benson

A LTHOUGH a considerable number of experi--ti mental investigations dealing with the roasting of sulfide minerals have been reported in the past,'"" the behavior of the single roasting particle does not appear to have received the attention it perhaps deserves. This is understandable in that the natural sulfide counterpart of the slab or sheet of metal normally used in high temperature oxidation studies is difficult to obtain and prepare, and is, in most cases, virtually impossible to maintain in one piece at roasting temperatures. The employment, on the other hand, of static aggregations of small particles in masses great enough to permit evaluation of the roasting reactions by means of thermobalances or gas analyses introduces other complications, such as localized overheating, sintering, and variable gas-solid contact. In this investigation a compromise between the above extremes was attempted. Closely sized (e.g., 30 to 40 mesh) particles of natural sulfide minerals were isothermally roasted, out of contact with one another, in an air-swept system. The progress of the roasting reactions was followed by examination in polished section of the treated particles and by X-ray and chemical analysis of their residual sulfide kernels. In this way some conclusions respecting the mechanism of roasting reactions were drawn. Roasting Furnace—The vertical tube furnace used for roasting the sulfide particles had a heated zone 10 1/2 in. long in which four retractable light gage stainless steel trays were suspended. Each tray, and an accompanying baffle, was mounted on a 2 in. iength of 3/8 in. stainless steel tubing. These assemblies were axially suspended on a 30 in. length of in. stainless tubing, by means of which they could be lifted from the hot zone to a water-cooled brass chamber at the top of the furnace. Since each tray unit could slide freely on the 30 in. tube, any desired number of the trays could be retained in the cooling chamber by the manipulation of a horizontal plunger during a momentary withdrawal of the four trays from the hot zone. Although three heating coils, each equipped with variable external resistance, were employed, it was found impossible to avoid a drop of 10O to 15OC between the temperature at the top tray and that of the lower three. Consequently, only the bottom three trays were used for roasting. Temperature readings inside the furnace were made by means of a thermocouple inserted down the tray support tube at tray levels, and a separate thermocouple, inserted adjacent to the middle heating coil, was connected to a Micromax temperature control unit. Experimental Method—The sulfide minerals were obtained in a form as free as possible from gangue and contaminating sulfides, and were crushed and screened to the required particle size range. The tray assembly was kept inside the furnace during the heating-up period and, when a steady temperature had been reached, the trays were withdrawn. Each tray was sprinkled with from 200 to 500 mg of the sulfide grains, and the assembly was lowered into the furnace without delay in order to minimize the time required to achieve the operating temperature. The furnace top was then clamped into position and the thermocouple inserted down the center tube to the required level. It was found that, when this procedure was used, the trays achieved their former temperature within 2 min, after which time the flow of dry air was begun at a rate of 1 liter per min, and timing of the run was started. At the required intervals of time the trays were successively withdrawn from the hot zone and stored in the cooling chamber by means of the retention plunger. On completion of the run the treated particles were removed from the trays to be set aside for examination. The roasted particles were mounted in Lucite on a Buehler press operating at a temperature of 146°C

Jan 1, 1958

By J. G. Richardson

The performance of laboratory water floods is compared with the flooding behavior calculated by the Buckley-Leverett techniques from steady-state relative permeability-saturation relations. Both the steady-state and unsteady-state experiments were conducted on the same sand-packed column. Relative permeabilities were calculated by the Welge technique from the unsteady-state waterflooding displacement experiments and compared with those measured by steady-state techniques. An evaluation of the various calculation procedures was made. It was demonstrated that steady-state relative permeabilities could be used to calczcJate waterflood performance. INTRODUCTION To calculate the waterflooding behavior of a given reservoir, relative permeability-saturation relations of the reservoir rock are required. These relative permeabilities are commonly measured on core samples by steady-state experiments such as the Penn State technique.' The relative permeabilities obtained in steady-state experiments are calculated from oil and gas flow rates and pressure drops measured under conditions of equilibrium distribution of oil and water in the pore spaces with slow approach to equilibrium. On the other hand, in water floods the water saturation at a given point changes rapidly with time as the flood front passes. Extensive research2 has shown that the steady-state relative permeabilities to oil and water are independent of the rate of flow and the fluid viscosities. Research has also demonstrated that the waterflooding performance of homogeneous sands uniformly contacted by water is independent of rate when capillary pressure gradients, which are important in short laboratory columns, are made negligible. However, there is little experimental data in the literature comparing relative permeabilities calculated from steady-state flow experiments with those calculated from flooding experiments. In this paper, the production data of two water floods and the relative permeabilities calculated from a series of steady-state experiments on an unconsolidated sand column are presented along with the comparisons calculated by the Buckley-Leverett and by the Welge techniques. The purpose of this study was to determine if steady-state relative permeabilities could be used to predict the waterflooding performance. This study also permitted an evaluation of the Buckley-Leverett and Welge calculation procedures and allowed an insight into the nature of microscopic displacement of oil by water. EXPERIMENTAL APPARATUS AND PROCEDURE The apparatus used in this investigation was a Lucite column 1 ft long and 11/2 in. in diameter. A drawing of the apparatus is shown in Fig. 1. Six pressure taps were evenly spaced along the top of the column to measure the oil pressures. Three pressure taps fitted with small porous disks were spaced along the side of the column to measure water pressure. Water was admitted to the inflow face of the sand through a porous disk while oil was admitted through a hole in the porous disk and distributed to the face of the sand by grooves machined in the porous disk. Retainer screens of 325-mesh stainless steel were cemented over the inlet and outlet ports and the pressure taps to prevent loss of sand. The column was packed with a clean dry sand all of which was finer than 200 mesh. Next, the sand was saturated with a solution of 150,000 ppm sodium chloride solution. The column was weighed dry and water-saturated to obtain data for the calculation of the pore volume. A 151-cp oil was then injected into

Jan 1, 1958

By Henry B. Fernald

THE Federal income tax treatment of expenditures for exploration and development for mines and other natural deposits (other than oil and gas) was materially changed by special provisions of the 1951 Act that are continued in the present 1954 Code." These present provisions for mines in stance they are the same as the 1951 amendments to the 1939 Code, Secs. 23 (cc) and (ff), respectively, except that for exploration the allowable annual deduction is increased to $100,000 (from $75,000) and minor changes in case of property transfers are made with respect to the four-year limitation. Before 1951 the statutes made no specific pro- visions regarding development and exploration for mines, but the rules were prescribed by Treasury regulations: 1) Before the mine entered the production stage, all development and exploration expenditures for mines, less net receipts, were to be capitalized recoverable through depletion or written off as losses when determined worthless. 2) After a mine entered the production stage, development expenditures were deductible as expenses-currently if ordinary expenses, but on a deferred basis if extraordinary in scope. This recognized the two separate periods, one before and the other after beginning of the production stage. There was no distinction between an exploration and a development period, but exploration was included as part of development.

Jan 1, 1958

By W. C. Lacy

THE Cuajone porphyry copper deposit is the northernmost of a group of three deposits in southern Peru controlled by the Southern Peru Copper Corp.-Toquepala, Quelleveco, and Cuajone- all within a 20-mile belt. Although small pockets of high-grade copper oxide ores were worked in the Cuajone area in the 19th century, it was not until 1939 that its potentialities as a disseminated deposit were recognized by O. C. Schmedeman. An exploratory drilling program was begun in December 1942 and continued until early 1945. The program was revived in November 1952 and completed early in 1954. Early exploration was by diamond drilling. Later exploration was predominantly churn drilling, with diamond drilling used only for wildcat holes.

Jan 1, 1958

AIME Committee on Local Section Affairs Joseph L Gillson, Chairman J C Kinnear, Jr Lloyd E Elkins AIME Committee on Student Chapter Affairs (Special Committee, pending Bylaw revision) R F Mehl, Chairman E H Crabtree, Jr John C Calhoun, Jr

Jan 1, 1958

By J. H. O’Dette

BLISTER formation on wrought aluminum products has been a matter of concern to aluminum fabricators for many years. The fact that blisters make their appearance during the final stages of fabrication means that much time and effort have been expended before it is evident that the material must be scrapped. This and the loss of production are ample reasons for embarking on a research program to find out more about blistering and possible methods of control. Many excellent papers on this subject have appeared in the technical literature in the last few years. In one of the more recent papers, Kostronl gives a fairly complete review of the problem of gas in aluminum and blistering in general. From the work of the various investigators, a general mechanism for the formation of blisters has evolved and may be summarized briefly as follows: Hydrogen gas is usually present in the cast ingot, in the atomic or ionic state, in excess of the solid solubility. At room temperature the gas atoms are relatively immobile, but at elevated temperatures they become mobile and diffuse to free surfaces where they associate to form molecules. If these free surfaces are discontinuities within the ingot then the associated gas molecules collect and build up considerable pressure until equilibrium is reached with the dissolved gas around the discontinuity. Since the solubility of the gas is proportional to the square root of the partial pressure it is evident that large pressures may be built up at the discontinuities. When the metal is rolled to sheet the pressure of the gas in these, discontinuities is sufficient to deform the surface of the sheet and form a blister, particularly when the strength of the material is reduced during the annealing. Although the mechanism of the formation of blisters was fairly well known, the actual impor- tance of the individual roles played by the gas and the discontinuities was not so well established that positive methods for control of blistering were at hand. It was the object of the investigation to learn more about the nature of the discontinuities giving rise to blistering and to develop methods of control. The investigation was carried out in three stages as follows: a) A study of the more commonly used methods of removing hydrogen from aluminum, such as fluxing and holding, and their effects on blistering. b) Location of the discontinuities giving rise to blistering. c) A study, by indirect methods, of the movement of gas in the metal and its effect on blistering, and the development of methods of blister control during fabrication. Removing Gas and Reducing Blistering by Fluxing or Holding-—The work of removing gas and reducing blistering by fluxing or holding was carried out on metal of Alcan 2s (1100) composition with an artificially high gas content. The high gas content was obtained by introducing water into the melt prior to casting; the water reacted with the aluminum forming A12O3 and hydrogen. The procedure was to raise the gas content by introducing water into an aluminum melt and using half the melt to cast one ingot immediately. The remaining metal was treated again with water to make up for the reduction in gas content during holding, while the first ingot was being cast, and then given a fluxing or holding treatment and cast into an ingot. Samples for gas determination were cast from the molten metal before and after the gassing operation; before, after, and during fluxing, and while casting. Samples were also cut from sections of the ingots. Gas determinations were made on these samples using the well known vacuum fusion technique. All ingots were hot rolled at 500°C to 0.250-in. slab which, in turn, was cold rolled to 0.040 in. sheet. The sheet was coiled and annealed for 2 hr at 500 °C and then cut into 5-in. squares which were inspected for

Jan 1, 1958

By R. P. Carreker

ONE of a series, this report is concerned with the experimental documentation of the deformation behavior of pure metals over a wide range of temperature. Previous reports in the series describe the creep behavior of platinum1 and aluminum2 and the tensile behavior of copper,&apos; silver,& and molybdenum.5 Subsequent reports will describe the creep behavior of copper and silver and the tensile behavior of platinum, thus providing extensive creep and tensile data on four face-centered-cubic metals tested under comparable conditions. Material Two lots of high-purity aluminum were used in this investigation. One lot, designated AC, was obtained direct from the Aluminum Co. of America as high-purity aluminum in notch-bar form. A typical analysis of this type of aluminum is 0.006 pct Si, 0.015 pct Cu, 0.006 pct Fe, and 99.975 pct Al. Lot BS was obtained from J. I. Hoffman of the Bureau of Standards as a portion of the Aluminum A described in his report of the redetermination of the atomic weight of aluminum.6 Lot BS originated with the Aluminum Co. of America also, and was received in the standard notch-bar form. A detailed chemical and spectroscopic analysis of lot BS has been published.6 Principa1 impurities were 0.006 pct Si, 0.003 pct Fe, 0.002 pct Cu, and >99.987 pct Al. Samples were processed identically by room-temperature swaging and drawing to 0.030 in. diam wires from approximately ½ in. diam rods that were machined from the notch-bar pigs. Samples were cut from the cold-drawn wire, placed in a grooved graphite block in groups of thirteen, and annealed in air for 1 hr at each of several temperatures, with the results shown in Table I. The two lots of aluminum responded quite differently to annealing, the behavior of aluminum AC suggesting that its grain growth was controlled by impurities. The recrystallization texture of aluminum of similar purity comparably treated has been reported as predominantly <111> fiber with some <100> fiber present.7 Testing Procedure The testing procedure and method of analyzing the data have been described previously.2,3 Annealed specimens of 5 in. gage length were tested in an Instron tensile testing machine at a constant head motion corresponding to a strain rate of 0.04 min-&apos; at a number of temperatures. Instantaneous tenfold rate changes were employed in some tests to deter-

Jan 1, 1958

Jan 1, 1958

By F. D. Rosi

IT was recently shown1 that slip bands can be observed in bent germanium crystals after deformation, by means of etch pits along the slip traces. It is the purpose of this note to show how chemical etch pits can also be usedto examine the appear- ance of slip bands in silicon, as well as other deformation markings. A 30 ohm-cm, p-type single crystal bar, 2x1/4x1/8 in., was plastically bent at approximately 1200°C in a vacuum of 1x10-5 mm Hg. The axis of the crystal was coincident with a <III> direction, and the surface normal to the axis of bending was within 4" of a (110) plane. Prior to the deformation, the (110) surface was mechanically polished with

Jan 1, 1958