Search Documents

By Roorda H. J, R. R. Saddington, Curlook W

THE copper-nickel sulfide ore deposits of the International Nickel Company of Canada, Limited contain the minerals pyrrhotite, pentlandite, and chalcopyrite. In the extraction of the nickel, copper, and iron, much of the processing involves oxidation of the metals as well as sulfur. Roasting plays a predominant role at several stages in the operations which prepare the constituent metals for refining. Copper, nickel and iron concentrates of various grades, ranging from low-grade nickeliferous pyrrhotite to high-grade nickel sulfide, must be partially or completely oxidized. Figure 1 shows the main points at which roasting is conducted at INCO. Roasting experience at INCO dates back to the time when lump ore was partially roasted in heaps. It has progressed through single hearth roasters, sinter machines, multiple-hearth roasters, flash roasters, and more recently has centered on the development and utilization of fluid bed roasters. The primitive, slow, and inefficient method of heap

Jan 1, 1961

By Christopher Riley

A relatively unexplored lead zinc deposit lies about 12 miles northwest of Revelstoke, B.C., in the highly metamorphosed Monashee Group of rocks of the Shuswap Terrane, Precambrian in age. Host rocks are of sedimentary origin and consist of gneisses, schists, marbles and quartzites with intermediary types. The marbles and quartzites provide good horizon markers. Using these it is possible to interpret the controlling structure which is a syncline overturned to the north, dipping south at about 45°, and plunging east at about 12°. The syncline is truncated at about halfway of its length on a peak on the west side of which a partial cross section together with superimposed minor folds may be seen. The quartzites and the two marble beds may be traced over much of the structure. There are two lodes, above the marble and below the quartzite, which converge eastward and which are the exposed edges of the same host bed -an impure limestone.

Jan 1, 1961

By N. E. Rogen, N. J. Grant

WHILE direct measurements of the growth of precipitate particles during aging is of fundamental value, few such measurements have been made. Direct measurements by means of optical or electron-microscopy and X-ray techniques are preferred, however, many of the aging studies have been based on indirect methods such as electrical resistivity and hardness. Because of the minute size of most precipitate particles (less than 1000A) the light microscope is of limited use while electron microscopy is subject to slowness, etching problems and consequent resolution problems. It is fortunate that alloys of the Nimonic type, based on Ni-Cr-Ti-Al, lend themselves to accurate and relatively easy particle size measurements. With proper balance of titanium and aluminum, the only aging precipitate is the gamma prime (r') Ni3,(Al, Ti)2 phase and this phase is the basis of the high-temperature strength of these allos.3-6 The Ni3(Al, Ti) phase is a face-centered-cubic, ordered structure with nickel atoms occupying the cube faces. Titanium atoms can replace three out of every five aluminum atoms and when substituting do so preferentially.2 Electron microscopy has shown that during aging of most of the commercial alloys of this type, precipitate particles are unusually uniform in size and distribution, and that the volume of (r') phase is large (20 pct).4,7 The aim of this investigation was to measure the growth of (y') phase during aging. In so doing, it was hoped that a clearer understanding of the aging process would be attained. X-ray line broadening was used as the measure of precipitate particle size. This technique was selected because it can measure and average the diameter of thousands of particles in one operation. The variations in hardness and matrix lattice parameter with aging were also studied and related to the particle size. EXPERIMENTAL PROCEDURE An alloy of the following composition was studied: Cr Ti A1 C Ni Wt pct 20.71 2.98 1.43 0.04 bal. At. pct 22.06 3.47 2.95 0.18 bal. The alloy, a 15- lb vacuum melt, was forged to 1/2-in. diam at a temperature of 1900" to 2200°F; was solution heat treated for 4 hr at 2000°F and water quenched; and was then aged in various ways. The ASTM grain size was 4 to 5. No (7') phase could be detected by X-ray analysis after solution treatment and electrolytic extraction. Aging was performed on 2-in. long specimens at 1400°, 1500°, and 1600°F for increasing times. One-half inch sections were removed after each time increment and were then electropolished in a solution of H3P04 saturated with chromium trioxide at a potential of 30 v and rectified with a tantalum electrode. Rockwell hardness measurements were taken using one side of the polished specimen. Matrix lattice parameter determinations were made on the other side using filtered chromium radiation references with the position of the (220) line of a silicon standard. To enable the precipitate particles of the (y') phase to be measured using X-ray line broadening techniques, it is first necessary to separate and concentrate this phase by electrolytic extraction. Extraction is necessary because the difference between matrix and precipitate lattice parameters is only approximately 0.5 pct and intensities of.the (y') phase lines are very weak relative to those of the matrix. The extraction techniques employed have been described before and found to produce a reasonably quantitative separation.398 A water solution of 15 pct H3Po4 is used at a current density of 0.5 amp per sq in. at 6 v. The precipitate particles are separated from the liquor by centrifuging and decanting and are then washed, dried and repowdered. A plot of the X-ray intensity vs diffraction angle for the (111) line of the precipitate particles was used as a measure of particle size. The intensity curve approximated the shape of Gaussian distribution function and its breadth was measured at the half height. The (220) line of a silicon standard was used to correct the measured line breadth for instrumental and other broadening errors. The Scherrer formula was used to calculate particle

Jan 1, 1961

By A. Roberts

This paper reviews progress in equipment design and in the techniques applied to mine lighting in Great Britain. The incidence of the disease miner's nystagmus, which was a major source of concern only a few years ago, has now diminished, largely owing to improvements in standards of lighting in mines. The reorganisation of the coal mining industry, involving increasing mech-anisation, together with new safety legislation, has brought about the widespread use of mains electric lighting underground. An account is given of some of the results of research to determine the lighting conditions needed for compliance with the compulsory legal requirement of "sufficient and suitable" general lighting at specific localities in British mines. Some details are given of the techniques applied and the results of recent research in the problem of glare from miners' cap lamps. Of the various factors in the working environment of the miner, it is true to say that lighting is seldom given attention comparable with that devoted to other factors, such as dust, heat and humidity, or atmospheric gas content. No doubt one reason for this lies in the ability of the human eye to adapt itself to low brightness levels. Be that as it may, the fact is that at the turn of the 20th century the miner's working light improved little throughout the centuries during which mining technology has developed. Indeed, in coal mines which encounter a methane explosion hazard, flame safety lamps, with a luminous intensity less than one candle power, were virtually the sole means of lighting during almost the whole of the 19th century. The 20th century has witnessed a substantial improvement in lighting techniques underground in coal and metalliferous mining. In Great Britain the general pattern has been one of standards periodically raised by the implementation of Statutory Regulations imposed under successive hlines Acts, but it is fair to add that the more progressive mining companies usually anticipated the Statutory Regulations, which when they have been put into effect have served to turn into general practice what was already being done at the better mines. In earlier years, official requirements were limited to the specification of approved lamp designs, with stipulated minimum values of luminous intensity and light output, but more recently the necessity of satisfactory maintenance of standards during service has been recognized, and the current regulations not only require that a maintenance organisation should exist, but also specify a maximum permissible depreciation below initial approval standards.'

Jan 1, 1961

By J. D. Mote, J. E. Dorn

This investigation was undertaken to study the effects of piledup arrays of dislocations on inducing slip, twinning, and fracturing in magnesium bicrystals. A series of variously oriented bicrystals of magnesium having a vertical grain boundary were prepared and tested in tension. It was found that piled-up arrays of dislocations at the grain boundary could, under appropriate conditions, induce slip, twinning- and cracking. The results that were obtained substantiate, at least qualitatively, the general dislocation mechanism for transmission of strain across grain boundaries and the Petch-Stroh concept of fracturing. WHEREAS single crystals of magnesium generally exhibit extensive deformation, coarse-grained poly-crystalline magnesium at subatmospheric temperatures fractures after a few percent elongation.' Although a small amount of ductility is obtained, several features of this fracturing are characteristic of typical brittle behavior. Over a rather broad temperature range the fracture stress is insensitive to the test temperature and the fracture stress increases linearly with the reciprocal of the square root of the mean grain diameter. The course of fracturing is predominantly intergranular, but small fragments of adjacent grains frequently adhere to the fractured surface.2 The brittle behavior of polycrystalline magnesium is attributable to the limited number of facile deformation mechanisms it exhibits at low temperatures. For a general deformation of a randomly oriented polycrystalline aggregate, each grain must exhibit at least five independent mechanisms of deformation to permit accommodation of the imposed deformation from grain to grain.= Although minor amounts of prismatic slip occur in corners of grains where stress concentrations are known to be high, glide in polycrystalline magnesium at low temperatures takes place almost exclusively by basal slip.' The common type of twinning, which takes place on the (1012) pyramidal planes, can under the most favorable orientations, lead to a. strain of only 6.9 pet; the contribution of twinning to the tensile strain would indeed be much less than this in a randomly oriented polycrystalline aggregate of magnesium. Since the three mechanisms of basal slip are coplanar, they are equivalent to only two independent mechanisms, a number insufficient for a general deformation. Consequently, once the permissible twinning has taken place in conjunction with basal slip, no further plastic deformation is possible because of interference to slip at the boundaries of dissimilarly oriented grains. At this stage brittle fracturing takes place due to high stress concentrations at the juncture of slip bands with the grain boundaries; the predominance of intergranular fracturing in magnesium, in preference to transcrystalline fracturing which is prevalent in zinc, has not yet been rationalized. A more atomistic description of the plastic behavior and fracture characteristics of magnesium follows from the analyses made by stroh4 on the stresses induced by piledup arrays of dislocations. Slip first takes place by dislocation motion in the most favorably oriented grains. As the dislocations approach the boundary of a dissimilarly oriented adjacent grain they begin to form an array of dislocations with its attendant stress field. Piledup arrays of screw and edge dislocations introduce high localized shear stresses at the spur of the array; piledup arrays of edge dislocations also induce high tensile stresses localized in the vicinity of the grain boundary. Whereas the shear stresses can induce slip to take place, the tensile stresses, if sufficiently high, can cause fracturing. The localized shear stress will be relieved if sufficient numbers of mechanisms of deformation become operative in the original and the adjacent grain to permit accommodation of the dislocations in the grain boundary. In this event a ductile behavior will be obtained. But if the number of deformation mechanisms is insufficient for complete migration of dislocation arrays into the grain boundary, the tensile stresses due to the edge components of piledup dislocation arrays will continue to increase with increasing applied stress until fracturing takes place. Whereas face-centered-cubic metals have a sufficient number of mechanisms of slip for accommodation of dislocations in their grain boundaries to exhibit ductile behavior, hexagonal-close-packed metals, in general, do not. Consequently, hexagonal-close-packed metals are usually brittle except when conditions such as alloying or temperature permit facile slip by a number of mechanisms. The arguments presented above suggest that the mechanical behavior of magnesium depends on whether or not dislocation arrays in adjacent grains can enter the grain boundary. When such accommodation is possible, ductile behavior is expected; but when such accommodation is impossible, fracturing will ensue. To further test the validity of these arguments it was considered advisable to study the

Jan 1, 1961

By H. W. Hockin, D. r. Brandt, R. H. Walsh, P. L. Dietz, P. R. Girardot

New Jersey, Florida, and Canadian ilmenites were reduced with hydrogen or coke under various experimental conditions and the phase changes occurring in the ilmenite upon reduction have been studied by microscopic examination of polished sections and by X-ray diffraction. The products formed were dependent upon the type of ilmenite, temperature, time and reducing agent. Of the reducing agents, hydrogen was the more effective at lower temperatures. 1 HE possible utilization of ilmenite as a source of both iron and titanium has resulted in the development of a number of methods for the separation of the iron and titanium content. Slagging processes as currently used in Canada are typical of such methods. Somewhat less attention has been given industrially to the reduction of the iron content at less than the slagging temperature. Although references maybe found to such work, in general only one type of ilmenite, either natural or synthetic, has been studied by each author. We have attempted to draw some relationship between the results of experimental reduction and the type of deposit from which the ilmenite was derived, as evidenced by phases occurring in the ores and in the reduction products. Ilmenite ores having from 27 to 61 pct titanium dioxide were included in this study and in each case reduction was carried out at such temperatures that only limited coalescence of the particulate iron product occurred within the ilmenite grains. The history of the individual ilmenite samples and the temperature of reduction were found to determine the occurrence of various phases and the mode of distribution of the iron. REVIEW OF EARLIER WORK ON REDUCTION One of the earliest references to the reduction of ilmenite at less than the slagging temperature was made in 1917.' The metallic iron produced was_____ leached out by the action of dilute sulfuric or hydrochloric acid, to leave a product high in titanium dioxide. Subsequent to this, numerous patents2-'? and other references13"21 have appeared concerning reduction of ilmenite by carbon, hydrogen, carbon monoxide, methane, coal gas, water gas, or the like in the absence of fluxing agents. Mineragraphic examinations were not reported, and in the main, the only examinations made were chemical analyses. However, in two cases3,13, titanium suboxides were reported in the products and in one case2' rutile was reported, in addition to metallic iron. Both were identified by X-ray diffraction. While reductions in the absence of fluxing agents were generally followed by either a wet or dry chemical process for removal of the metallic iron, a Canadian source17 reported removal of the metallic iron by magnetic separation. By the addition of fluxing agents during reduction, the metallic iron has been coalesced into "pearls." Each reference to such a process23-28 has shown that the coalesced iron could be removed by magnetic or gravity means after the product was crushed. In the absence of fluxes, the coalescence did not generally occur. The major part of the present study has been limited to reductions without fluxing agents in order to determine the primary reactions of naturally occurring ilmenites. Titaniferous iron ores have also been studied,29-33 17, l9 their reduction having been used as the basis of a commercial process for beneficiation of such ores in Norway29 and more recently considered in the United States34,35. The ease of reduction of titaniferous iron ores relative to that of hematite or magnetite has been referred to,33 with the conclusion that the more

Jan 1, 1961

By R. L. Bailey

"The Acheson D-3 Pool was discovered in August 1950, and contains 88 producing oil wells on 40 acre spacing. Initial oil-in-place was 118 million stock tank barrels and initial well potentials averaged 2,000 barrels per day.In early 1956 studies of hydraulic interference between the Acheson and Leduc D-3 Pools were conducted on the Carter Petroleum Reservoir Analyzer. These studies indicated that the natural water drive to Acheson would be incapable of replacing reasonable withdrawal rates over the life of the pool. To avoid shrinkage losses a scheme of pressure maintenance by water• injection was therefore instituted in March 1957.This pressure maintenance scheme is notable because pressure is being effectively maintained by high volume injection through one well located on the flank of the pool. Close control on reservoir behaviour is maintained by regular bottom-hole pres-sure surveys and observation of water cuts on producing wells. No evidence of pressure gradients or channelling of the injected water has been observed to date, and the water-oil contact has remained level over the whole field. It is possible to control the average reservoir pressure within very close limits by varying the rate of fresh water injection.Ultimate recovery estimated from the rise of the oil-water contact and calculated water influx to December 31, 1958, is 335 barrels per acre foot, or a total of 91.4 million barrels from the pool. This compares to 217 barrels Per acre foot or a total of 59.4 million barrels indicated from laboratory test data."

Jan 1, 1961

By Horace Pops, J. F. Libsch

THE discovery of SAP alloys (sintered aluminum powders) by lrmannl has stimulated investigations in other alloy systems.23 Not only do such alloys have good room-temperature properties, but they maintain high strength after prolonged service at elevated temperatures. In addition, they show high structural stability, including unusually high recrystallization temperatures. These characteristics are secured by dispersion hardening. For this investigation, Zn-ZnO alloys were selected. Practically, the fact that commercially pure zinc recrystallizes near room temperature prohibits strengthening and hardening by cold deformation and therefore limits the application of zinc where mechanical strength is important. Similarly, the poor

Jan 1, 1961

By P. G. Thornhill

EARLY in 1951, Falconbridge undertook a research program aimed at the development of a sulphate roasting process for the recovery of the non-ferrous rnetals from the nickeliferous pyrrhotite fraction of Falconbridge ore, in order to reduce the tonnage of iron entering the srnelter. Such a method, it was hoped, would permit a high recovery of the nickel from pyrrhotite otherwise entering the smelter feed, thus not only raising the grade of the latter and reducing its iron content, but also providing an iron oxide residue useful as a source of by-product iron ore. At an early stage in the exploratory laboratory test work it was found that the degree to which the nickel could be solubilized by the sulphating roasting treatment was limited by particle size and the ex-tent to which the pyrrhotite concentrates were freed of the nickel occurring as physically separable pentlandite, a mineral relatively difficult to roast. ( 1) Thus the program

Jan 1, 1961

By W. Dan Walker

In an effort to keep mine hoist accidents to a minimum and to impart to managers and workers the essential elements that enter into safe installation and maintenance of hoisting equipment, the Bureau of Mines presents this Information Circular as a guide. Hoisting of men and materials is an essential operation in many mines and has become so commonplace that some persons are likely to ignore day-to-day inspections or become lax in the operating phases. With proper maintenance and operation, hoists can be exceptionally safe. However, lack of strict attention can invite tragedy or costly shutdowns.

Jan 1, 1961

By William J. Campbell

The purpose of this investigation by the Federal Bureau of Mines was to design and construct a fluorescent X-ray spectrograph for dynamic rate studies of selective oxidation in molten metals and to establish basic principles for interpretation of data obtained by this method. An X-ray spectrograph was constructed in which the sample holder is a resistance wound furnace; it was operated up to 800° C. in oxidizing atmospheres. No difficulties were experienced with the cooling or heating systems nor with the protective layer of mica around the X-ray tube window, even though the oxidizing surface of the metal is only 0.5 inch from the X-ray tube window, Means are provided for heating under controlled atmospheres for selected time? temperature cycles.

Jan 1, 1961

By R. L. Marovelli

ANTICIPATING the eventual use of the huge tonnages of nonmagnetic taconites of the Mesabi range of the United States, the Federal Bureau of Mines is classifying and evaluating these deposits in detail. This introductory report describes work begun in 1954 as part of a long-range program to sample, classify, and evaluate important occurrences of nonmagnetic taconite on the Mesabi, range. Included in this report are brief discussions of the geology, history, and potential of the Mesabi range district and mining industry, together with a more detailed presentation of the sampling and metallurgical evaluation of these nonmagnetic taconite deposits. A total of 898 field samples was collected. Most of these were taken in the region between Grand Rapids and Chisholm, Minn., but a few came from the area between Chisholm and Buhl, Minn. Of the total samples, 865 were from open pit bank faces where the greater vertical distances presented by the cherty members facilitated the taking of a large number of samples. Conversely, the narrow face presented by the slaty members confined and limited the areas from which samples were taken. In addition, 33 of the field samples were taken from rock dumps in order to determine, in a preliminary way, the characteristics of these materials.

Jan 1, 1961

By R. P. Jewett

The object of this investigation was to correlate the crushing strength of green pellets prepared from magnetite, specular and earthy hematite with the particle size of these respective raw materials. In this study no attempt was made to correlate the strength of fired pellets and particle size. The effect of particle size upon a number of fine ores and concentrates was studied. Much of the low-grade ore reserves in the Lake Superior Region must be finely ground before concentration and then agglomerated for iron and steelmaking processes. Fine natural ores also must be agglomerated. Pellets constitute an important type of agglomerate. Considerable handling occurs during screening to remove undersize and oversize pellets, and in transfering green unfired pellets from the balling machines to the heat-hardening equipment. As a result the strength of the green pellets is a factor of great importance.

Jan 1, 1961

By K. K. Kershner

Nickel having a purity of more than 99.99 percent with reference to metallic impurities was electrodeposited at the Rolla Metallurgy Research Center of the Federal Bureau of Mines. The production of high-purity nickel is in keeping with the current trend in technologies for producing metals with lower and lower percentages of impurities. To understand more fully the role to be played by nickel by itself and as a component in many alloys, the element must be in a state of high purity. Procedures are outlined for purifying nickel solutions by precipitating and filtering off impurities. Details are given for using the purified solutions as electrolytes in depositing high-purity nickel. The elecneleposited nickel contained 0.0005 to 0.002 percent each of cobalt, copper, aid iron together with spectrographically detectable traces of aluminum, magnesium, and silicon. The deposits were smooth and dense; the crystalline structure was typical of an electrodeposited metal. Some preliminary experiments for purifying nickel solutions by liquid-liquid extraction are also described in this report. Tests of this type were limited since more encouraging results were obtained by other methods of purification.

Jan 1, 1961

By F. W. Wood

A program of research was conducted by the Bureau of Mines to investigate anomalies in electrical-discharge behavior during consumable-electrode arc melting of titanium and to study the effects of these irregularities on arc-furnace explosions. A major effort was devoted to an experimental survey of arc behavior and a qualitative definition of discharge phenomena.3/ An important conclusion was that the "glow" of industrial arc-melting terminology is not a glow discharge but a skittering arc in a displaced position. The conditions that permit displaced skittering were tentatively defined. The displaced skittering arcs tended to damage melting crucibles in two ways, and details of possible mechanisms leading to crucible rupture and explosive reactions have been proposed accordingly. However, no acceptable means of preventing crucible damage was discovered.

Jan 1, 1961

By D. Z. Hobbs

Because an economic method for preparing pure boron has not been developed, a program was started by the Bureau of Mines to evaluate existing techniques or to develop new methods for preparing the pure element. This report describes investigations directed toward the development of techniques for the preparation of pure boron by fused-salt electrolysis. Only two of the several fused-salt baths tested were satisfactory for the preparation of boron. These baths contained (1) potassium fluoride, lithium fluoride, potassium fluoborate and boron trioxide; and (2) potassium fluoride, potassium chloride, and boron trioxide. Of these two mixtures, the latter was more satisfactory. Elemental boron of from 90- to 95-percent purity and, in isolated cases, as high as 98-percent purity, was prepared from these two types of fused-salt baths. There appeared to be no distinct differences either in the yields or the purity of boron prepared at current densities ranging from 795 to 1,000 amperes per square foot. Current efficiencies were as high as 85 percent.

Jan 1, 1961

By Joseph A. Sutton

The prospect of utilizing bacteria in mining and metallurgical processes introduces a new and challenging area of investigation. Elements of bacteriology and metallurgy are discussed in connection with possible areas where biological science might be applied in extractive metallurgy. Bacteria may prove important in the selective separation of metals from ores and metallurgical solutions, the production of sulfur from gypsum or pyrites, and the production of sulfuric acid from elemental sulfur. A series of reports concerning the experimental applications of bacteria on minerals and metallic ores will follow this paper. For several years the Bureau of Mines has been investigating the action of bacteria in the oxidation of sulfide minerals and their potential uses in metallurgical processes. Primary attention has been given to the possible utilization of certain strains of autotrophic bacteria that live in industrial leaching solutions or fractures of mineral outcrops. The purpose of this paper is to acquaint the mining and metallurgical engineer with micro-organisms and some of their possible applications in the field of extractive metallurgy.

Jan 1, 1961

By H. H. Bein

Most western industrial sands are feldspathic and contain feldspars in variahle amounts. A few deposits will show alumina contents of less than one per cent while others will contain over twelve per cent alumina. Some industries are not especially concerned with the amount of contained feldspar but are interested only in color and in size gradations. Other industries, however, are very much interested in alumina content and set up quite rigid specifications as to this content. Several western plants are beneficiating crude sands both to reduce the iron content and to control the feldspar content. At present, most of these plants are using flotation processes for both controls although a few plants do use magnetic separators for the reduction of iron content. Some work has also been done with electrostatic separators for the feldspar-quartz splits. The Sand Division of Del Monte Properties Company, Pebble Beach, California, has been operating a flotation plant for iron removal and the separation of quartz and feldspar since 1950. As mentioned before, control of alumina, especially in the quartz product, is very important. Some users require an alumina content of less than two per cent and others will demand a product of less than one per cent Al2,O3,. The standard Quinolate method for determining alumina is lengthy and time consuming. The HF —H2SO4 evaporation step is especially critical and, if forced, spattering is apt to occur with a resulting loss of sample. Standard procedure is to evaporate to dry ness overnight at a low temperature. Even with forcing under optimum conditions the procerlnre will take two or three hours to complete. A new method has been developed which allows an alumina determination to be made, in 10 or 15 minutes, on a sample of the quartz product as it is being produced. This pocedure, although simply an approximation, has been most helpful in showing whether or not the product being formed is meeting specifications. This procedure has also allowed a great reduction in samples formerly taken and analysed by the orthodox method. Whether a sample assays 1.75% A12O3, or 1.95% .41,0, is not so important as the fact that it is below the allowable maximum of 2.00%. Similar thinking would apply to products required to contain less than 1.00% A1,0,. The step by step procedures for the method are as follows: 1. Collect sample, drain or filter, and dry. 2. Split sample through standard Jones sample cutter to quarter or eighth sample, depending on size of original sample taken, then split down to about 5 grams through Sepor micro-splitter. 3. Screen through 50 mesh sieve (U.S. Series) and reject undersize. 4. Weigh out 2 grams and place in platinum crucible. 5. Etch with 3-5 mls 38.40% HF for 1 minute at room temp. 6. Decant and wash. 7. Stain for two minutes in same crucible with a 1% water solution of Nigrosene dye. 8. Decant and wash well. 9. Dry.

Jan 1, 1961

By F. D. Wright

Production of a coal preparation plant is governed by many restrictions, such as the tonnage of different products and blends that can be sold within a given period, capacities and output proportions of the cleaning and sizing units, blending proportions, quality specifications, and costs and prices for the various products. Determination of the tonnage of each product and blend that should be made in order to obtain the maximum profit can be difficult unless a systematic method such as linear programming is used. In this paper the basic method of linear programming is described briefly. The Old Ben No. 9 preparation plant is used as an example to illustrate in detail how eqwations can be written to form a linear programming model of a coal preparation plant. Three sample problems, each requiring 56 or more equations and 63 structural variables, were solved with an IBM 650 computer. Linear programming is one of several mathematical tools used for operations research. It has been applied to many fields and has been used by a number of industries either to maximize the profits of certain operations or to minimize costs. P. B. Nalle and L. W. weeks' have described the use of the method by the Riverside Cement Co. to minimize the cost of blending raw materials to make portland cement. Their problem is to obtain at minimum cost a mix with certain specifications from a number of possible materials which have various costs and various amounts of CaO, SiO2, Fe2O3, and other constituents. In a paper on the use of linear programming by the National Coal Board in England, K. B. Williams and K. B. Halley2 describe how the transportation method, a variation of linear programming, is used to minimize the cost of sending 37 grades of coal from 28 mines to seven central washing plants which produce coal for furnace coke and foundry coke. The various coals have different percentages of volatile matter, moisture, sulfur, ash, and phosphorous, so there is considerable choice in how they can be blended to meet the specifications of the two products. The purpose of this paper is to show how linear programming can be used to maximize the profits of a coal washing plant which produces individual final products as well as blends. The Old Ben Corp. furnished assumed sample data from their Old Ben Mine No. 9 preparation plant for this investigation. However, the data that have been used are entirely the author's responsibility. METHOD OF LINEAR PROGRAMMING Numerous articles and books have been written on the theory and applications of linear programming.3-5 However, since the method has not been widely applied by the mining industry, a brief, nontheo-retical discussion of its basic method seems to be in order. Linear programming (Table I) is used to determine the best possible solution to a number of interdependent activities. It is essentially a method for making systematic selections from a number of possible solutions to determine positively the optimum solution. There may be other equally good solutions but no better ones. Each activity must have linear coefficients and there must be a criterion to judge how good the solution actually is. Linear programming is different from the solution

Jan 1, 1961

By P. Schwarzkopf, J. H. Brophy, J. Wulff

A constitutional diagram has been proposed for the tantalum-rhenium alloy system. Rhenium dissolved in tantalum up to 48 wt pct, and the maximum solubility of tantalum in rhenium is 5 wt pct. Intermediate x and s phases were found. X-ray diffraction, metallography and melting points were employed. SEVERAL investigators have described the phases present in the tantalum-rhenium alloy system, but no detailed account of the phase diagram prior to the present investigation appears to be available. Greenfield and Beck' reported the solubility of 48 to 54 at. pct Re in tantalum, a s phase at 41 at. pct Ta, and x phase isomorphous with a Mn from 37 at. pct Ta to less than 25 at. pct. They employed as-arc melted specimens and heat treatments at 1200 °C lasting 72 hr.2 Duwez3 reported the existence of a a phase at the composition Re3Ta2. Niemiec and Trzebiatowski4 observed a lattice parameter a = 9.69A, for the x phase at a composition Ta7Re22, but no s phase. Savitiski and Tylkina5 have shown a hardness maximum at the composition 40 at, pct Ta and a somewhat lower plateau from 35 to 10 at. pct. Knapton6 indicated results similar to those of Greenfield and Beck.' The present investigation describes the phase relationships in the tantalum-rhenium alloy system determined by melting point measurements, X-ray diffraction and fluorescence, and metallography. EXPERIMENTAL PROCEDURE Commercial 99.7 pct Ta powder from Fansteel Metallurgical Corp. and 99.9 pct Re powder from Chase Brass and Copper Co. were used for alloy preparation. The powders were weighed to desired nominal compositions and then pressed without binder into compacts weighing 5 or 10 g. The compacts were arc-melted six times on alternate sides on a water-cooled copper hearth using a nonconsumable tungsten electrode in an atmosphere of titanium gettered helium, at a pressure of 500 mm Hg. In most cases this procedure yielded alloy buttons of satisfactory homogeneity. A series of alloy specimens were analyzed wet chemically for use as standards for X-ray fluorescence. All specimens were analyzed by fluorescence and the results showed that the compositions differed by less than 3 pct Re from the original as-weighed nominal composition.* On the basis of self-

Jan 1, 1961