Search Documents

By W. C. Smith, P. J. Hickey

After a short historical background of the process evolution, this article descvibes present-day plant facilities and operating techniques utilized for high-purity bismuth production. The plant is one of the world's largest, with an annual output of some one million pounds of refined bismutlz. PREVIOUS papers1 written by staff members of Cerro de Pasco Corp. have referred briefly to the production of refined bismuth. Since the Corporation is one of the world's foremost producers of high-purity bismuth, a detailed description of the process for extracting the metal may be of general interest. Following a short historical background of the development of the actual process, this presentation will trace the progress of bismuth from its entry into the primary smelting circuits to its concentration in electrolytic lead cell slimes. Our facilities for the treatment of anode muds will be described and the extractive methods given in some detail, with particular emphasis on the techniques which result in the production of refined metal. HISTORICAL BACKGROUND Shortly after Cerro de Pasco began smelting operations at Oroya, Peru in 1922, it became apparent that the dust carried by copper converter gas contained appreciable amounts of bismuth. Although dust collection efficiency was poor prior to building of the 550-ft stack and installation of the central cottrells in 1938, a large stock of dust was accumulated during the intervening years, having the following approximate composition: Oz. per ton Ag - 11.0 Pct Sn — 0.5 Pct Pb - 49.0 Pct Zn - 6.5 Pct Bi - 2.0 Pct Insol. - 1.5 Pct Cu - 0.7 Pct Fe - 2.3 Pct Sb - 3.0 Pct S - 10.0 Pct As - 7.5 In the mid-1920's, experimental crucible melts of this dust with carbon indicated that most of the bismuth and silver, and some of the lead, could be reduced to a fairly clean bullion. Other products were a small amount of leady copper matte and a slag high in zinc, arsenic, antimony, and lead; this slag contained some tin but only small quantities of silver, bismuth, and copper. After the laboratory results had been confirmed by operation of a small reverberatory, a dust reduction furnace was constructed. The ±10 pct Bi-Pb bullion produced from this operation was stocked until 1930, when an Oroya-designed converter type furnace3 was installed for the elimination of arsenic, antimony, and some lead from the bullion. This process concentrated the bismuth from 10 to about 60 pct. By means of the bismuth process developed4 by W. C. Smith at East Chicago (1909-1914) and the discovery of a method5 for separation of lead from bismuth with chlorine gas in 1929, it became possible to begin production of refined bismuth. Unfortunately, bismuth deleaded with chlorine always contained residual chlorides, and the removal of the chlorides by caustic soda left a lead content of 0.02 to 0.04 pct. This final problem was solved6 by substitution of air-blowing for the caustic treatment, which effectively removed all excess chlorine and gave bismuth which was practically lead-free. In 1934, a pilot electrolytic lead refinery began operations at Oroya. Lead smelting was resumed in 1935 and two years later a 100-ton-per-day lead refinery was put into service. In conjunction with the latter, the present-day Anode Residue Plant was constructed. Until 1940, the plant treated both lead anode slimes and dust reduction bullion. The dust reduction furnace was shut down in that year, and all cottrell dusts (with the exception of the product from the arsenic cottrell) were mixed with pyrite and treated in a Wedge roaster to eliminate all possible arsenic. Calcine from this operation joined the sinter plant feed; hence the bismuth from the copper and lead circuits was collected in the lead bullion and subsequently in lead anode slimes from the electrolytic lead refinery. The latter source has been the only bismuth-bearing material of any consequence entering the Anode Residue Plant from late 1940 to the present. A copper refinery began operating in 1948, and the cell mud from this plant is mixed with lead slimes and processed through the same circuit, though only a small quantity of bismuth is present in electrolytic copper cell residues. BISMUTH INTAKE Present-day routes which are followed by the new bismuth feed from its entry into the primary smelting circuits to its arrival at the Anode Residue Plant are traced schematically in Fig. 1. As illus-

Jan 1, 1962

By Robert F. Stewart

The oxidation of structural materials at high temperatures in gas-cooled systems can be greatly retarded by the addition of small amounts of hydrogen to the inert coolant. In experimental equipment for gasifying coal with heat transferred by helium, the oxidation of graphite and metals (molybdenum, tungsten, and certain stainless steels) by trace impurities in the coolant helium was virtually eliminated by adding 0.1 to 1.0 percent hydrogen. The reaction of hydrogen with praphite does not preclude its use to retard oxidation; at 2,400° F. only 0.2 pound of graphite per square foot per year is lost for each percent of hydrogen in the helium. The addition of hydrogen appeared to prevent the mass transfer of carbon often associated with oxidation of graphite, without causing noticeable embrittlement of stainless steels and molybdenum or other damaging effects. This method has been tested in precision gas-recycle systems and applied successfully for more than a year in a pilot-scale unit operating at 250 pounds per square inch gage and 2,400° F. It is now used routinely and can be applied to many gas-cooled systems operating at high temperatures.

Jan 1, 1962

By G. E. Peacock

SIGMA MINES is situated in the township of Bourlamaque, Abitibi County, Quebec. It is a gold producer, and presently treats an average of 1,200 tons of ore per day, at a grade of approximately 0.18 oz. per ton recovered. The mill started operations in March, I937, at a rate of 300 tons per day. This was increased to 800 tons in I940, and to 1,000 tons by I943. The rate was cut back during the war years, but was brought back up to capacity by I948. The mill tonnage was in-creased to the present 1,200 tons per day in I960. The underground workings are serviced through No. 2 Shaft (Figure 1), which, with 24 operating levels, extends from surface to a depth of 3,317 feet. When depth exploration was decided upon, two possibilities were considered: (a) deepen the main shaft by1,000 feet; (b) put down a winze for the same distance.

Jan 1, 1962

By G. A. Mancini, V. Bharucha, J. W. Spretnak, G. W. Powell

The characteristics of the motion of the a interface during the "down" transformation was studied in zone-refined iron and dilute binary alloys containing nickel and molybdenum by means of the thermionic emission microscope and high speed photography. The frontal movements were found in all cases to be definitely discontinuous with time and an appreciable number of incremental jumps were found to proceed in the reverse direction (a to b). Molybdenum was found to be particularly effective in increasing the frequency of the increments of transformation from the stable to the metastable phase. A knowledge of the mechanism by which alloying elements affect the hardenability of a steel is desirable from both the practical and scientific viewpoints. It is well established that microstructures consisting of tempered martensite and lower bainite exhibit the best performance in terms of toughness and resistance to crack propagation. The presence of some upper transformation products, namely ferrite and pearlite, is in general undesirable. Various researches have indicated that the ferrite matrix grain structure is a very important difference between the upper and lower transformation products, namely equi-axed vs acicular. Any comprehensive theory of the decomposition of austenite should explain the dependency of the morphology of the matrix on undercooling. The contribution of various alloying elements to hardenability has been determined experimentally and catalogued in considerable detail. A rationalization of the basic mechanism or mechanisms by which individual elements affect the kinetics of the decomposition of austenite to products other than the phase "martensite" has not been evolved as yet. Interest in this problem was stimulated by the effects of minute quantities of boron in hardenable steels. This paper deals with one aspect of this problem, namely the characteristics of the ?-a transformation in high-purity iron and in two carbon-free iron binary alloys. A detailed historical account of the scientific developments in the study of the decomposition of austenite would be a prodigious undertaking and will not be attempted here. There are several excellent reviews in the literature on the formation of pearlite, martensitic reactions, and kinetics of solid-state reactions. The thinking on reaction mechanisms has been influenced to a large degree by the "classical" Tammann nucleation and growth model, in which an embryo springs into being by a fluctuation, and grows to a critical size through atom by atom deposition. Such a process is expected, accordingly, to be diffusion controlled. Considerable research attempting to relate the contribution of alloying elements to hardenability on the basis of their effect on the diffusivity of carbon in iron has not been productive from a mechanistic viewpoint. The formation of pearlite and ferrite has been treated in terms of nucleation and growth processes in which presumably the lattice transformation also occurs by a diffusion process. The other prominently considered mechanism is the "martensitic" or cooperative shearing mechanism. It seems generally, but not entirely, agreed that the phase "martensite" forms by this mechanism, and that it is involved to some extent in

Jan 1, 1962

By C. M. Wayman, J. F. Breedis

The crystallography of the martensitic transformation in the Fe-30 Ni alloy was reinvestigated. The scatter in the habit Plane as determined from measurements on the mid-rib plane was smaller than reported previously, and the orientation relationship was determined from a martensite plate having known direction cosines. From agreement with crystallographic theory and from observations of the morphnlogy of the martensite plates, it is suggested that the mid-rib plane represents the starting region of the transformation. THE crystallography of the martensitic transformation in the iron-nickel system has been the subject of many investigations.&apos;-7 However, for iron alloys containing approximately 30 wt pct Ni, a wide scatter in the reported habit planes exists. In only one instance has a Laue determination of the orientation relationship been made, but the habit plane of the martensite plate studied was not determined experimentally. Because the most successful thermodynamic and kinetic analyses8 of the martensite transformation have been based on Fe-30 Ni alloys, it was considered desirable to reinvestigate the crystallographic features of the transformation in this alloy. Lieberman9 suggested that the most significant information for use in a theoretical treatment involves the determination of all the crystallographic observables from a single plate of the product phase. This was first done in essence by Greninger and Troiano10 for Fe-22 wt pct Ni-0.8 wt pct C, and is the method followed in this investigation. Some theoretical approaches11-13 in describing the martensitic transformation consider the overall transformation distortion to be comprised of a Bain distortion, or lattice deformation (PI, which produces the structure change, and a lattice invariant deformation (G), such as twinning, which together leave the interface or habit plane un-distorted. The incorporation of a rigid body rotation (R) results in a transformation distortion (E) such that the interface plane is left both undistorted and unrotated. In matrix notation, E = RPG where the lattice invariant deformation has "taken place" in the austenite. Bowles and Mackenzie14-16 in formulating a theoretical approach proposed an adjustable scaler quantity, denoted as 6, which represents a uniform dilation in the interface plane. This dilation acts to adjust the lattice spacings of the parent and product structures at the plane of contact. Using the dilation parameter as a variable, these authors were able to account for a continuous variation of habit planes in steels along a curve in the stereogram between {225}A and {259}A. she invariant line strain14 of the transformation is 6 RP, and the corresponding transformation distortion is E/6.) With the dilation parameter known, the invariant line is computed as the triple coincidence of the habit plane, the shear plane of the lattice invariant deformation, and the initial Bain cone.14 The contraction axis for the Bain distortion can be taken9&apos;17 as [010]A, and the correct permutation of the habit plane indices used. Kelly and Nutting 18 have established the shear plane (of twinning) in the tetragonal martensite of Fe-22 Ni-0.8C to be {112)M by means of transmission electron microscopy. The reasonable shear system is then {112}M which is equivalent to {011}A <01l>A. The as-

Jan 1, 1962

By John R. Gould

A mathematical treatment of multiple-pass floating-zone refining of semiconductors, including the evaporation of solutes from the melt at reduced pressure, is presented. Vapor pressures and evaporation rate constants for phosphorus, arsenic, and antimony in germanium have been determined from floating-zone experiments conducted at 10 mm Hg. Rate sensi-tivity of arsenic in germanium has been examined over the range of 1 to 10 in. per hr growth rate. The equilibrium value of the segregation coefficient of arsenic in germanium, as determined by an extrapolation of these data, was found to be 0.09. PFANN has treated the segregation of nonvolatile solutes in the zone-melting process, Bradshaw and Mlavsky2 considered the evaporation of solutes in a vacuum during the growth of crystals by pulling from the melt, and van den Boomgaard3 has shown that it is possible to bring a volatile impurity element homogeneously into an ingot by means of zone-melting under a constant pressure of that element. This paper is concerned with the volatilization of solutes during zone - melting in a vacuum. The mathematical analysis by Lord4 of multiple-pass zone melting is extended to include evaporation of solutes. A method is presented in which evaluations of vapor pressures, evaporation rate constants, and distribution coefficients may be derived from the variation of solute concentration in the floating-zone refining of germanium at 105 mm Hg. EXPERIMENTAL Ingots of zone refined germanium, approximately 1/4 in. in diam and 10 to 12 in. in length, were subjected to several floating-zone passes at 105 mm Hg in order to provide intrinsic material for these studies. These ingots were then seeded in a [Ill] direction and solid-doped to a constant impurity concentration of approximately 1015 atoms per cmS in a forming gas ambient (10 pct H - 90 pct A) at 1/2 atm gage. The resulting crystals were subjected to repeated floating-zone passes at 105 mm Hg and a concentration profile along the length made after termination of each pass. Concentrations were determined from four-point probe resistivity measurements, and proper precautions were taken to prevent contamination during handling. A constant zone length, crystal cross section, and growth rate were maintained during zoning. A stationary coil and moving crystal system were employed for floating-zone growth with neither the section of crystal above nor below the melt rotated.

Jan 1, 1962

By J. W. Spretnak, G. W. Cunningham

Grain growth across the bond region in Pressure bonded copper was found to be mainly dependent upon the presence or absence of microvoids, but it was also found that prior history, bonding pressure, bonding time, and bonding temperature are important variables. An increase in pressure, time, or temperature tends to promote grain growth in the interfacial region. Polygonization is observed after pressure bonding except for specimens previously annealed at temperatures on the order of 1800°F or higher. The dislocation density in bonded specimens was found to be greater in the bond region. THE bonding of metals by the application of gas pressure at elevated temperatures is a relatively new process, having been developed over the past 10 years. The technique, as described by Paprocki, Hodge, and Boyer,l is unique in that assemblies of many parts and complex shapes can be bonded with a negligible amount of deformation. The process thus differs metallurgically from pressure welding, cold welding, and recrystallization welding in that deformation occurs only in a microscopic region whereas, in general, the welding requires severe deformation and may extend the contact surface by a factor of 3 to 10 during the welding. From a practical standpoint, pressure welding is not amenable for bonding large surfaces. During the time in which Paprocki and coworkers were deve1oping the process, West2 established aproc-ess,for bonding aluminum to uranium, and Barnes and Maze? developed a gas-pressure-bonding technique for nickel and copper. Recently, Fugardi and Zambro4 have used equipment similar to that developed by Paprocki and coworkers to establish parameters for bonding stainless steel, aluminum, and zirconium. Most of the investigations on pressure bonding have been empirical in nature and, although methods have been developed for bonding such metals as molybdenum, columbium, titanium, zirconium, and stainless steel, the information concerning the mechanism of bonding is limited. Several workers5"7 have studied the pressure bonding of dissimilar metals in order to gain information on diffusion and formation of inter-metallic phases under application of pressure. Clapson and Robbins8 have shown by a series of annealing studies that voids in the interfacial boundary of roll-bonded copper can prevent movement of the boundary until the voids are spaced far enough apart to prevent pinning. They also indicated that recrystallization and grain growth can eliminate the voids. In this paper it is shown that voids are the major detriment to grain growth across pressure-bonded interfaces, but it is also shown that prior history, bonding pressure, bonding time, and bonding temperature are

Jan 1, 1962

By Nicholas J. Grant, Rolf Nordheim, Bill C. Gissen

The system Cb-Re was examined in detail utilizing pure metals, careful melting techniques, and heat treatments. Metallographic and X-my methods were utilized for phase identification. In addition to soli-dus determinations, the composition limits and mode of formation of the intermetallic compounds 0 and X were determined. The binary constitution diagram Cb-Re has been the subject of a number of investigations.&apos;-7 Two intermetallic phases have been described and tentative diagrams have been proposed. It was the aim of this investigation to obtain a complete and more accurate diagram through the use of purer alloys and improved techniques. The diagram worked out by Knapton7 was published after our experiments were concluded. EXPERIMENTAL METHODS The starting materials were Re powder of 99.95 pct purity, supplied by the Chase Brass and Copper Co., and Cb rondelles of 99.6 pct purity, supplied by the Electro Metallurgical Co. Typical analyses are given in Table I. The alloys were prepared from compacted Re powder and Cb rondelles; for critical compositions master alloys were used. The melts varied from 5 to 50 g and were melted nonconsumably in an Heraeus arc furnace, under ti-tanium-gettered laboratory grade argon. It was necessary to invert the buttons and remelt, followed by crushing and further remeltings, the number of which depended on the nature of the fracture of the alloy. The weight of each alloy was carefully checked after each melting operation. It was found that significant weight losses occurred only when loose Re powder was used. These losses amounted to a maximum of 3 wt pct in such instances, but did not occur after the charge was once molten, regardless of the composition. Typical loss of weight after 4 remelts, including crushing, amounted to 0.2 wt pct. Oxygen pickup during successive melting cycles did not appear to be significant, since the weight gain values never exceeded 0.01 wt pct. Control of the composition of the alloys was not too difficult; however, the problem of homogenization was a far greater one. Optimum alloying conditions were finally achieved by a combination of master alloy production and repeated crushing and remelting cycles. The compositions of the alloys utilized to determine the constitution diagram are listed in Table 11. The weight balance method was used ultimately as the sole analytical method, since repeated checks indicated that it was accurate to 0.2 pct, if the weight losses were small. The results were double-checked by a metallographic study of the homogeneity of the samples, since this was presumed to be the more serious factor. Heat treatments at 1200°C or lower were accomplished by sealing the specimens in Vycor tubes, heating in a Globar furnace, followed by air cooling. This was considered to be an adequate quench because of the very low temperatures involved. For temperatures of 1200" to 1900°, alloys were homogenized and heat treated in a tungsten-filament resistance vacuum furnace. From 1900" to 2750" a tantalum-tube resistance furnace was utilized, operating under a vacuum of 105 mm Hg. The temperature measurements up to 1200" were made by means of platinum-platinum 10 pct Rh thermocouples, with an accuracy of 5°C. For temperature measurements greater than 1200°C, optical pyrometers were used. They were calibrated against a standardized instru-

Jan 1, 1962

By K. J. Gill, P. Chiotti

Thermal, metallographic, and vapor pressure data were obtained to establish the phase diagram for the thorium-zinc system. Four compounds corresponding to the stoichiometric formulas Th2Zn, ThZn2, ThZn4, and Th2Zn17 were observed. The melting points of these compounds under constrained vapor conditions were found to be 1055°, 1105°, 1095°, and 1015°C respectively. Four eutectics exist in this system with the following eutectic temperatures and thorium contents in wt pct: 1040°C, 89 Th; 945°C, 79 Th; 1045°C, 55 Th; and 995°C, 35 Th. The standard free energy, enthalpy, and entropy of formation for the compounds were determined from zinc vapor pressure data. ALTHOUGH the thorium-zinc system has been of technical importance in the commercial production of thorium and more recently of interest to some proposed pyrometallurgical separations processes for reactor fuels or blanket materials no detailed investigation of this system has been made in the past. Some previous work has been reviewed by Hanssen.1 The existence of four compounds, Th2Zn17, ThZn4, ThZn2, and Th2Zn has been established and their crystal structures have been studied by X-ray diffraction techniques.2-4 Smirnov et al.,5 determined the solubility of thorium in zinc and investigated the two-phase region between Th2Zn17 and zinc. They calculated some of the thermodynamic properties for these alloys from emf measurements on the cells Th/ThCl4(fused)/Cl2, C and Th2Zn17(s)+ Zn (l)/ThCl4(fused)/Cl2, C. The possibility of reaction between the anode materials and fused thorium tetrachloride to produce a lower valent thorium salt would have to be resolved in order to evaluate the results obtained. The purpose of the present investigation is to establish the phase diagram for the thorium-zinc system and to determine the standard free energy, enthalpy, and entropy of formation for the compounds formed. MATERIALS AND EXPERIMENTAL PROCEDURES The metals employed in the preparation of alloys were Bunker Hill slab zinc, 99.99 pct pure and Ames Lalboratory thorium. The major impurities in the thorium in parts per million were oxygen—1250, carbon—350, iron—100, nitrogen-75, and silicon—70. The metals in the form of several small massive pieces, total weight about 30 g, were cleaned with acid, washed with water and acetone, and dried just prior to their use for alloy preparation. Tantalum containers were found to be suitable for all the alloys studied and were used throughout this investigation. The metals were sealed inside of small 1-in.-diam tantalum crucibles by welding on preformed tantalum covers. A small thermocouple well made from 1/8-in.-diam tantalum tubing was welded in the bottom of each crucible. These crucibles were enclosed in

Jan 1, 1962

By Willard L. Hunter

The research described in this Bureau of Minus report was conducted to improve the chromium-iron ratio of offgrade chromite. Two methods were used: (1) Iron was selectively reduced from chromite by carbothermic reduction in an electric-arc furnace, and (2) a mixture of carbon, chromite, and sometimes fluorspar was chlorinated to remove a substantial part of the iron. Chromite concentrate from the Mouat deposit in Montana and from northern California was used in the test work. Chromium-bearing slag and chromite that had been beneficiated by a roast-leach process were each smelted to produce high-carbon ferrochromium. Iron was selectively reduced in a laboratory-scale., electric-arc furnace. Carbon additions to the smelting charges varied from 40 to 100 percent of the stoichiometric requirement, and slag basicities were varied from 0.4 to 1.0 chromium-iron ratios of more than 4:1 were obtained with 89 percent recovery of chromium in a chromium-bearing slag.

Jan 1, 1962

By T. T. Campbell

Research conducted by the Bureau of Mines demonstrated the feasibility of preparing columbium and tantalum metals by the application of Kroll-process techniques. Yields in excess of 95 percent were obtained in a modified Kroll-process reduction apparatus constructed from nickel and Inconel.4 Operating conditions during reduction and distillation were determined. Optimum temperatures during sodium reductions ranged from 650° to 750° C and for magnesium from 700° to 800° C with retort pressures ranging from 3 to 7 psig. Undesirable vapor phase reactions occurred when temperatures exceeded 750° C during sodium reductions or 850° C with magnesium. Vacuum distillation at 850° C effectively removed volatile salts and excess reductant from the reduced metals. Calculations based on the results obtained in small scale tests indicate that reaction rates of up to 34 lb/hr could be obtained during columbium reductions and up to 60 lb/hr during tantalum reductions in production scale reac¬tors. The small, laboratory-scale techniques used in this study could be adapted to commercial practice. The reduced powder or sponge metals can be consolidated by conventional arc-melting techniques, and the arc-melted metals can be fabricated into ductile sheet at room temperature. Analyses of arc-melted buttons prepared from Kroll-process tantalum or columbium showed that tantalum of greater than 99.8-percent purity was obtained and that columbium purity exceeded 99.7 percent. A significant purification of the reduced metals occurred when they were consolidated by electron-beam melting, and the purity and ductility of electron-beam-melted Kroll-process tantalum and columbium compared favorably with the commercial metals. After electron-beam melting, the purity of the tantalum exceeded 99.95 percent, and columbium purity was approximately 99.9 percent.

Jan 1, 1962

By D. N. Williams

THE present study was undertaken with two specific objectives: measurement of the thermal-expansion coefficient of ß titanium and examination of the effect of solid-solution alloying on the thermal expansion coefficient. Four titanium alloy niaterials were available in the form of annealed 5/8-in. diam rod. Three of these, Ti-8V, Ti-20V, and Ti-6A1-4V, were prepared in the laboratory from 140 Bhn sponge. The

Jan 1, 1962

By D. S. Robertson

More than 700,000 feet of diamond drilling was completed in the Blind River area between 1953 and 1958. Much of this drilling was at depths which are still not usual in North America. However, as the tendency is to deeper holes, factual data from the Blind River operation may well provide information of value in future programs. Rates of drilling decreased with in-creasing depth, but uncommonly good rates (an average of over 50 feet per day over more than 4,000 feet of hole) were achieved with proper engineering and care. Costs varied as contractors and geologists became familiar with the area Hole deviation in the Blind River area was locally severe and control of the hole trace became a major problem. Careful surveying was necessary and found to be highly re-liable. It was found that control of the hole trace above 1,500 feet was much more difficult than at depths below 1,500 feet. This is explained by the mechanics of the drilling operation. Various methods of controlling hole deviation were attempted and,

Jan 1, 1962

By E. D. Calvert

The objective of this research was to examine variations in melting and forging practice for four titanium-base alloys and to determine their effect on the resultant product. Of particular interest was the evaluation of the skull-casting technique. The data should serve as a guide to producers and consumers of titanium products. Physical properties of four titanium-base alloys in ingot form and in sheet form were evaluated and correlated, where possible, with variations in the melting and casting procedure. Consumable-electrode melting was used throughout, but arc current and furnace backfill pressure were varied, and ingots were formed both by melting directly into a water-cooled copper mold and by skull melting followed by pouring into a graphite mold. Alloying metal additions for the alloys tested were (1) 8 percent manganese, (2) 6 percent aluminum and 4 percent vanadium, (3) 6 percent molybdenum and 2 percent aluminum, and (4) 16 percent vanadium and 2.8 percent aluminum.

Jan 1, 1962

By Leonard Obert

Between 1927 and 1957, sodium borate minerals were mined by underground methods in the Kramer District, Kern County, Calif. In 1957, surface mining methods were initiated, and during the next two or more decades it is probable that most of the production from the district will be obtained from open pits. However, part of this borate deposit is sufficiently deep that surface mining may not be economical and, hence, at some future date underground methods may again be employed. This report was prepared to document the underground mining methods employed in the district before 1957. The general geology of the district and the detailed geology of each of four mine sites are presented, together with a mineral and mechanical description of the ore and enveloping rock. The report also describes the stoping, extraction, pillar support, methods of artificial support, and other factors that affect the structural characteristics of these mines.

Jan 1, 1962

By G. H. Gronhovd

This report describes the design and initial operation of a slagging gasification pilot plant installed by the Bureau of Mines at the Lignite Research Laboratory, Grand Forks, N. Dak., in 1958-59. The tests covered in this report were conducted over a period of about 2 years, beginning in April 1959. The pilot plant was designed for eventual operation at pressures ranging from 400 to 600 p.s.i.g. (pounds per square inch gage); however, for the preliminary test reported here, the gasifier was fitted with a low-pressure slagging section and operated at atmospheric pressure and at 80 p.s.i.g. The reason for using a low-pressure slagging section for initial operation was to facilitate modifications in design during the development of a reliable slagging procedure.

Jan 1, 1962

By R. Steinitz, J. L. Orehotsky

An analysis was made of the influence of floating molten zone traversal on the purification of tungsten rods and the effect of this purification on the brittle -to-ductile transition temperature. The major impurities detectable in the original rods, i.e., molybdenum and oxygen, were reduced by zone refining from 30 to 3 Ppm. Changes in the trace amounts of other impurities could not be quantitatively determined since they were below the limit of detection. Tensile tests on 3-mil wires, drawn from these rods and recrystallized to 17,000 grains per sq mm, showed a transition temperature of 60°C for the zone Purified and 175°C for the original material. 1 HE brittle-to-ductile transition temperature is manifest mainly in the bee metals, iron,&apos; molybdenum, chromium,3 tungsten,4 and niobium. Since many of these metals cannot be fabricated at room temperature in a commercially pure annealed poly-crystalline state, a considerable amount of work has been done on evaluating the influence of purification on the transition temperature in order to determine indirectly whether the fabricability of these metals can be improved by removing impurities. Smith and Rutherford8 showed that the transition temperature of iron is lowered significantly by zone purification. Working with chromium, Edwards, Nish, and wain7 found also that purification appreciably lowered the transition temperature. A similar evaluation has so far not been reported for tungsten, probably because of the difficulties in obtaining tungsten in a purified polycrystalline state. carlson8 and, more recently, schadler9 have purified tungsten rods by floating zone traversal, but after zone traversal, their rods were single crystals. To obtain high-purity polycrystalline tungsten, a technique has to be round for transforming the zone-purified single crystal material into a suitable polycrystalline structure. The purpose of this investigation was to obtain zone-purified tungsten in a suitable polycrystalline state and then to evaluate the effect of zone purification on the transition temperature.

Jan 1, 1962

By A. H. C. A. Zimmerman

WE have just heard what must be regarded as a thoughtful, constructive and somewhat painful analysis of the financial function of our industry. While thinking about this, it is interesting to reflect on the conditions which have stunted the growth of the financial side of our affairs. Mining must be regarded as a wealthy business. •while immeasurable grub takes and development budgets have been lost, there can be little argument that a productive ore-body nearly always produces the type of wealth that breeds some extravagance. I recognize that this statement can be attacked from many sides, but an historical comparison with a commercial enterprise involving similar investment will demonstrate what I mean. However, these old times are be-ginning to disappear for a variety of reasons. High amongst these are: ( l) Increased costs of exploration. (2) Remoteness of many new finds. (3) Fixed or declining metal prices (particularly when expressed in constant dollars). ( 4) Constant demands for higher wages.

Jan 1, 1962

I am sure that you are- all familiar with Airborne Magneto-meter Surveying so I shall-spend only a brief moment describing the instrument and techniques and the remainder of the allotted time-on-modern-application-of the instrument.The Airborne Magnetometer used by Aero Service in AUstralia-was designated by Gulf Research and implements the saturable-core flux-gate--principle. The first magnetometers developed&apos;weremagnetic-balances and depended on the counter-torque principle but these required a stable platform and hence are not applicable to airborne surveying. Other methods include the induction methods, the Hall Effect methods, magneto-striction methods., Deflectioh. of,free.electrons, the proton-precession methods.Some: of these are applicable to airborne surveying. As a matter of-fact the nuclear precession magnetometer is the one generally used in the Satellites because it has been miniaturized most successfully.The Gulf Magnetometer is the one most generally used in mineral and petroleum exploration because its sensitivity is sufficient for the problem and-data and instrument techniques have been worked out and standardized.

Jan 1, 1962

By G. S. Upadhyaya, A. D. McQuillan

HERE would appear to be a simple relationship between the group number in the periodic table of the early transition metals and the maximum amount of hydrogen which they can absorb.&apos; Thus group IIIA metals (Sc, Y, and La) yield a trihydride in which the metal atoms are on a fcc lattice and the hydrogen atoms occupy both tetrahedral and octahedral interstices. Group IVA metals (Ti, Zr, Hf) form dihy-drides in which the metal atoms are on either a fct or cubic lattice, but in which only the tetrahedral interstices are occupied by hydrogen atoms. In group VA (V, Nb, Ta) the hydrogen-saturated metal attains a composition slightly below that of a monohydride under normal conditions. Finally the metals of group VIA (Cr, Mo, W) do not dissolve appreciable quantities of hydrogen. The manner in which hydrogen solubility disappears on alloying a group VA metal with one from group VIA has previously been investigated.2 It is necessary, in order to obtain a general picture of the reactions of alloys of the early transition metals with hydrogen, to examine a system containing metals from groups IVA and VA in which there must be a change from a fcc to a bee hydride phase. The system chosen for investigation was the pseudobinary system between titanium hydride and niobium hydride. Metallic alloys were prepared by melting iodide-prepared titanium with zone-refined niobium in an argon-atmosphere are-furnace. To ensure homogeneity each alloy was cold-swaged and then heated at 1250°C in a high-vacuum furnace until metallo-graphic examination confirmed its complete homogeneity. Small weighed specimens of the alloys were charged with hydrogen using gaseous hydrogen generated by heating titanium hydride. The apparatus has been described elsewhere.3 Throughout the charging process the hydrogen pressure was kept at about 1 atm while the specimen, initially at 800 °C, was slowly cooled to 150°C over a period of days. The total amount of hydrogen absorbed by each specimen and the room-temperature crystal structure of the hydride powders were determined. The X-ray investigation indicates that the fee hydride phase arises from alloys extending in composition from titanium to 67 at. pct Nb. After a two-phase field lying between 67 and 74 at. pct Nb in which the fee and bee hydrides coexist, all alloys richer in niobium yield a distorted bee hydride. Data derived from parameter measurements are presented in Fig. 1. The atomic volume per metal atom has been plotted against the composition of the initial metallic alloy in order to facilitate comparison of the effects of hydrogen addition in the two phases of different crystal structure. The amount of hydrogen absorbed by each alloy at saturation in terms of the hydrogen to metal ratio and alloy composition is given in Fig. 2. Over the whole range of the fee hydride phase the hydrogen content remains constant, while in the distorted body-centred hydride phase, the hydrogen content increases with increasing titanium content reaching a hydrogen/metal ratio of 1.4 at the boundary of the two-phase region. It seems likely, therefore, that the maximum hydrogen content of the fee hydrides is limited to a hydrogen/metal ratio of 2 because hydrogen atoms

Jan 1, 1962