Search Documents

By S. E. Haszko

SEVERAL new XGa2 intermetallic compounds, Table 1, where X is a rare earth, having the AlB, structure were prepared as part of a continuing study of the magnetic and structural properties of rare-earth alloys.' In this note, the crystallographic results of these compounds are presented. Chart, Eq. 121 for the data in Fig. 1 can be adequately represented by The corresponding standard free-energy change is AF; = -4.576 T log K = -20,900 + 10.20T [5I At low nitrogen concentrations the ratio of mole fraction to weight percentage is a constant so that the mole fraction X of nitrogen is given by X = 0.0392 [%NJ. At low values of X, the activity and the concearation approach each other, hence K, = 0.0392 K,, where K, is expressed in terms of the mole fraction of nitrogen. Hence Eqs. [4]. and [5] become

Jan 1, 1962

By B. D. Cullity, K. S. Sree Harsha

When a copper or aluminum single crystal is swaged into wire, the resulting deformation texture depends on the original orientation of the crystal. The<100> and <111>orientations me essentially stable, while <110> is unstable. The greater the <100> content of the deformation texture, the stronger the wire is in torsion. the greater the<111>content, the stvonger it is in tenszotz. The preferred orientation (texture) of fcc wires, either after deformation or recrystallization, is usually a double fiber texture in which some grains have <100> parallel to the wire axis and others have <111>. The relative amounts of these two texture components, as reported by different investigators for the same metal, vary considerably. Previous work in this laboratory&apos; has shown that the starting texture of a wire, i.e., the texture which it has before deformation, can have a decided influence on the texture produced by deformation. In particular, it was found that the deformation texture of copper wire is essentially a single <100> texture, if the wire before deformation contains only a <100> component. This is true even when the deformation is carried to more than 98 pct reduction in area. This paper reports on further studies of the role played by the starting texture. Copper and aluminum single crystals of various orientations have been cold swaged into wire, and quantitative measurements of the resulting deformation textures have been made. The tensile and torsional properties of the deformed wires have also been measured, and the relation between these properties has been correlated with the texture of the wire. These measurements were made in order to demonstrate that a cold-worked wire can be made relatively strong in torsion and weak in tension, or vice versa, by proper selection of the texture before deformation. MATERIALS The copper was of the tough-pitch variety, containing, by weight, 99.962 pct Cu, 0.003 pct Fe, 0.025 pct 0, and 0.0021 pct Si. The aluminum contained more than 99.99 pct .&apos;41; the only reported impurities were 0.001 pct Fe, 0.001 pct Si, and 0.003 pct Zn, by weight. Large single crystals of these metals were grown by the Bridgman method in graphite crucibles and a helium atmospliere. Cylindrical specimens of predetermined orientation, about 1.5 in. long and 0.36 in. in diameter, were machined from the as-grown crystals and then etched to 0.25 in. to remove the effects of machining. Their orientations were checked by back-reflection Laue photographs, and they were then swaged to a diameter of 0.050 in. (96 pct reduction in area). 111 order to study the "inside texture" of the deformed wires, they were etched, after swaging, to a diameter of 0.040 in. before the texture measurements were made. TEXTURE MEASUREMENTS The fiber texture which exists in wire or rod can be represented by a curve showing the relation between the pole density I, for some selected crystal-lographic plane, and the angle $ between the pole of that plane and the wire axis (fiber axis). Such a curve will show maxima at particular values of , and these values disclose the texture components which are present. The relative amounts of these components can be determined2&apos;3 from the areas under the maxima on a curve of I sin F vs F. It is seldom necesszlry to measure I over the whole range of F from 0 to 90 deg, since the existence of maxima in the low-F relgion can be inferred from measurements confined to the high-F region. The X-ray measurements were made with a General Electric XRD-5 diffractometer and filtered copper radiation, according to one or the other of the following procedures: 1) A method developed in this laboratory,4 involving diffraction from a single piece of wire. 2) A modification of the Field and Merchant method.5 This method was originally devised for the examination of sheet specimens, but it can easily be adapted to the measurement of fiber texture. Three or four short lengths of wire are held in grooves machined in the flat face of a special lucite specimen holder. The axes of the wires are parallel to the plane defined by the incident and diffracted X-ray beams, and the holder to which the wires are attached can be rotated step-wise about the diffractometer axis for measurements at various angles 9.

Jan 1, 1962

By N. M. Parikh, T. J. Koppenaal

The strengthening mechanism of fiber-reinforced silver has been investigated as a function of fiber density and fiber material. Stress-strain curves were determined in the range 2 x 10-6 to 2 x 10-3 plastic styain and slip lines were examined. The yield strength at 0.2 pct permanent strain is markedly dependent upon fiber density but the stress necessary to initiate plastic deformation is independent of fiber density. The strengthening mechanism of the fibers is shown to be malogous to grain boundary strengthening in poly crystalline metals. The variation in strengthening with different types of fibers is also noted and discussed. In recent years, considerable progress has been made in the understanding of the mechanical properties of two-phase systems, particularly in the classical dispersed-phase alloys where the separation between the dispersed phases is 0.01-0.1µ. However, little work has been done on fiber-reinforced metals where the dispersed-phase separation is considerably larger than this. Parikh1 investigated the mechanical properties of many fiber-reinforced metals and found that two general relationships are always observed, as follows: 1) A fibrous network incorporated into a second weaker metal strengthens the latter, and the amount of strengthening increases with fiber concentration. 2) At a corrstant fiber concentration, the amount of strengthening in a given matrix can vary considerably, depending upon the type of fiber employed. The object of the present investigation was to examine the fuiidamental factors controlling these two observations. procedure: Fig. 1 shows the initial step in the fabrication of the specimens. The sieve is shaken so that the fibers fall into a mold with the longitudinal axes of most fibers in the X-Z plane. The fibers are then compressed to a predetermined density, thus forming a "felt", and the necessary amount of matrix metal is added to the top of the felt. The mold is heated, in vacuum or hydrogen, to above the melting point of the matrix metal; the molten metal flows into the felt, and the entire assembly is cooled. This produces a "composite" that is essentially free of voids. A number of composites were prepared in this manner using 1/4-in. kinked lengths of mild steel

Jan 1, 1962

By Robin O. Williams

The increase in internal energy as the result of deformation has been measured for lead, aluminum, silver, nickel, iron, and zirconium by using rapid, adiabatic compression. The stored energy increase is roughly Proportional to the strain; the propor-tionality constant increases rapidly with increasing melting point. The fraction of the mechanical energy which is stored increases more slowly, since the strength of the metals also increases with melting point. The values of the stored energy are considered accurate to about 10 pet. The present values appear about 50 pet larger than the more reliable published results where comparisons are possible. It is possible that this difference is due to the high strain rate used in this investigation. Immediately after deformation all these metals release energy at a rate roughly proportional to (time)-&apos;. This release is considered to be associated with dislocation motion but in aluminum (and copper) some additional process seems to be present. This release can represent 20 pet or more of the stored energy. WHEN pure metals are plastically deformed, most of the mechanical energy is converted into heat. The energy remaining within the metal is significant in that it is the energy of the disorder produced and thus detailed knowledge of this energy is a powerful tool in understanding the nature of deformational disorder. While much effort has been expended on this problem, the amount of information available is limited. The situation as of 1958 has been carefully reviewed by Titchener and ever.&apos; The present results have been obtained by a new experimental approach to this problem. The method necessitates high-strain rates which make comparisons with published results less certain, but a high-strain rate is an advantage in that the energy release immediately after deformation can be followed. EXPERIMENTAL PROCEDURE In the experimental method used, the internal (stored) energy is given as the difference between the mechanical work used in deforming the sample and the heat which is released (the first law of thermodynamics). The work is supplied by two identical hammers swinging freely from a fixed height, the available energy being the product of the mass, the gravitational constant, and the distance through which the center of gravity moves. The initial temperature rise of the sample represents the heat produced by the deformation. The sample temperature is determined by a small thermocouple embedded in and supporting the sample. This process can be repeated over and over to produce increased strains. Most samples are run through about five cycles to a total strain of around 0.7. Further details are covered elsewhere. The determination of the heat is dependent upon the sample weight, its specific heat, the rise in temperature, and any gains or losses to the surroundings. One is dependent on published results for specific heals (the values were taken from a collection).3 The values must be accurate to about 0.1 pet in order that they not affect the results. The best values thus do not contribute to the uncertainty, but this is probably not always the case. The accuracy of the temperature rise is limited primarily by knowledge of the thermocouple characteristics over short temperature intervals, but careful calibration eliminates this as an important factor. One can calculate readily the heat flow between the sample and hammers if the time of contact and the sample temperature are known and if there were no oil at the interface. Assuming the maximum temperature difference, upper values for this interchange have been calculated (the time of contact is determined from the decrease in sample length) and it may or may not be significant. However, no correction is colnsidered necessary because of the presence of a thin oil film which has a thermal conductivity much less than the metals. Except for the possible uncertainty in specific heat, the heat is considered to be adequately known. The mechitnical losses which are recognized as important are: 1) friction between the sample and the hammer:;, 2) the kinetic energy in the hammer suspension system which may not be entirely usable, 3) the rebound energy of the hammers, and 4) the vibration of the hammer heads. All these have been covered in detail elsewhere2 and only the more significant points are made here. The friction turns out to be small except for soft materials (lead)

Jan 1, 1962

By J. B. Clark, A. S. Yue

The zone-melting technique can be adapted for the de-termination of the eutectic composition in complex metal systerrzs. The application of this method is demonstrated in a simple eutectic system, Mg-AE, in which the eutectic composition is known and in a complex ternary system, Mg-Al-Zn, in which the literature is uncertain as to the composition of the ternary eutectic. The advantages and limitations of this unique approach for the determirution of the eutectic composition are discussed. ThE eutectic composition in phase diagrams is usually determined by thermal analysis of a series of arbitarily selected alloy compositions. The temperatures of the liquidus and eutectic arrests for each alloy are plotted and the eutectic composition is estimated by extrapolation to the entectic temperature of the curve formed by the liquidus arrest temperatures for the series of alloys. Although this approach readily yields the eutectic temperatures, several dekrminations are needed to estimate the eutectic composition, even in a simple system. In a complex ternary system, a great many determinations are often necessary to estimate, even approximately, the ternary eutectic composition. Thus, the conventional method is inherently tedious and time consuming. The application of zone melting provides a relatively efficient method of determining the eutectic composition.&apos; As an illustration, consider the zone melting of an alloy composition C, in the simple eutectic system A-B, shown in Fig. 1, under the ideal conditions of infinitely rapid diffusion in the liquid, no diffusion in the solid, and ease of nucleation of both phases. As the zone moves along the bar, the composition of the zone is enriched by solute rejected during the freezing of the a phase and the zone composition approaches the eutectic composition CE.Once the zone composition attains the lowest melting composition, i.e., the eutectic composition, it remains at this composition as the zone moves along the bar and finally freezes as such at the end of the bar. Chemical analysis of the end of such a zone-melted bar then should yield the eutectic composition CE of the system A-B. A corresponding analysis can be made for a ternary eutectic system. Under the ideal conditions noted above, only one pass of the molten zone is required to yield the eutectic composition. Experimentally, however, a solute-rich layer forms at the solid-liquid interface2 and the composition of the zone does not attain the eutectic composition as rapidly or as uniformly as in the ideal case outlined above. But with agitation of the melt, the ideal conditions can be approximated experimentally. Also, as shown below, zone melting permits a cumulative build-up of the solute at the end of the bar to the eutectic composition. The purpose of this paper is to demonstrate this unique method for determining the eutectic composition. The method is here applied to two systems: first, to the binary Mg-A1 system, in which the composition is well established, and second, to the complex Mg-Al-Zn system in which there is doubt concerning the composition of the ternary eutectic. EXPERIMENTAL PROCEDURE The zone-melting apparatus used in this study is described in detail elsewhere.3 Briefly, the binary alloy rods (5/8 in. in diam and 9 in. long) and the ternary alloy rods (5/8 in. in diam and 6 in. long), with the compositions given in Table I, were zone

Jan 1, 1962

By R. L. Gall

This report describes Bureau of Mines experiments in gasifying coal in a helium-heated tube-coil reactor. The purpose of this work was to investigate helium as a medium for transferring heat from a nuclear reactor to gasify coal or for use as high-temperature process heat. A laboratory-scale system was designed and constructed to demonstrate feasibility. In preliminary tests with this system, in which the coal was fed as a water slurry, the helium-heating and recycling equipment operated well. Considerable difficulty was experienced, however, in preheating coal slurry to the desired range of 400° - 1,000° F. without plugging the preheaters. Five different preheaters plugged with coke or with salts leached from the coal. The longest operating period wan 12 hours. These difficulties were partly due to the relatively small equipment and flow rates. The gasifier processed l pound per hour of low-rank coal at 300 p.s.i.g. and 1,800° F., with the carbon conversion limited to 20 to 30 percent by the short residence time and slow heat-transfer rate.

Jan 1, 1962

By R. I. Jaffee, R. W. Wood, H. R. Ogden, D. N. Williams

D. W. Morgan, D. H. Polonis,and R Taggart (Uuivevsity of Washington)—Dispersion hardening in titanium-copper alloys is of particular interest to us in view of our current research activities in phase transformations in this system. We should like to raise questions concerning several points in the paper. The flow sheet for fabrication and heat treatment (Authors&apos; Fig. 2) indicates that 0.045 in sheet is treated in air for a period of 30 min at 1625&apos; F. Were any surface coatings used to reduce oxygen contamination at this stage? One might ask the same question about the 8-hr annealing at 1400F. Contamination during fabrication and heat treatment of such thin sections could be considerable without some protection. Although the authors state that no analyses were made, they note that contamination masks the distinction between base strengths of the different alloys. In this connection, what fabrication and heat-treatment procedures were used in obtaining the comparison specimens of unalloyed titanium? It would seem that oxygen contamination must cast doubt on the reliability of the proposed strength-mean free path relationship deduced from the data (Authors&apos; Fig. 5). It is usual to evaluate dispersion hardening on the basis of yield strength rather than ultimate tensile strength, and accordingly we have replotted the authors&apos; Fig. 1 to include yield strength. The yield strength data do not justify a discontinuity of 3 p at either 70" or 1000 OF. Can the authors substantiate their conclusion 1) with additional evidence? Otherwise it seems that they have succeeded only in pointing out the possibility of a linear relationship between yield strength (or Uts) and the logarithm of the nleall free path, comparable with that demonstrated for iron-carbon alloys (Authors&apos; Ref. 2). Work in our own laboratories has shown that the hardness of the phase Ti,Cu is 235 Vpn, and that of a 1.5 pct (at.) (2 pct wt) supersaturated solid solution of copper in titanium is 190 Vpn. This small difference in hardness would suggest that Ti2Cu should not be a very effective dispersion-hardening phase. D. N. Williams, R. W. Wood, H. R Ogden, RI. L Jaffee (authors&apos; reply)— This discussion brings out some interesting points with respect to the interpretation of our results, and also raises some questions regarding the experimental technique. We shall consider the latter questions first. Contamination during heat treatment was prevented by performing all heat treatments in argon-filled Vycor capsules. Fabrication was done in air, with the usually observed scaling. Scale was removed

Jan 1, 1962

By Paul Gordon, A. S. Iyer

Apreliminary investigation has been carried out on the annealing behavior of explosively deformed copper as compared to that of conventionally deformed copper, using hardness, stored energy, and the sharpening of X-ray spots on Debye rings as the measures of annealing. Some metallographic observations were also made. Two purities of copper were studied. The first was tough pitch copper obtained as a small piece from the guard ring of a sample explosively deformed to approximately 500 kbars.* The second consisted of mentedand deformed these samples quite badly so that only a few small fragments were available for the annealing experiments. As a result, little in the way of quantitatively significant data was gleaned from the measurements. However, several important qualitative differences between the annealing of explosively deformed and conventionally deformed copper have been observed. It is these effects which are described in this report. Fig. 1 presents the results of hardness and stored energy measurements during the annealing of the high-purity copper after explosive and after conventional deformation. The data for the conventionally deformed copper were taken from the work of Gordon;&apos; in this copper it is evident that most of the stored energy is released concommittantly with the hardness drop. As shown in orddon&apos;s&apos; investigation, these effect:: are definitely associated with recrystal-lization. In the case of the explosively deformed copper, on the other hand, a large fraction of the stored energy is released before any appreciable hardness change takes place. At 160°C about 40 pct, and at 170°C about. 80 pct, of the stored energy appears to have been released prior to the onset of softening, i.e., undoubtedly prior to recrystallization. In view of the facts that the hardness and energy measurements were made on separate samples and that there is reason to suspect that the intensity of the explosive deformation from sample to sample may not have been uniform, a check run was carried out in which both energq release and hardness changes were measured cnn the same sample. The results of this run, shown in Fig. 2, confirm the conclusion that much of the stored energy is released before the hardness begins to change appreciably. In an effort to obtain some idea of the activation energy associated with the early release of energy, a single callorimetric sample was annealed in two steps, first at 149.5"C and then at 159.5"C, Fig. 3.

Jan 1, 1962

By Thomas P. Meloy

Floating "fines" differs from floating "sands" because the fines have a much larger surface area compared to their mass. The forces that arise from this large specific surface the key to understanding the behavior and treatment of fine particles. Though the nature of these forces is not thoroughly understood, enough work has been done to give a qualitative picture of what is happening in a flotation cell. It is the purpose of this chapter to re-examine some of the more, recent theoretical work and-to indicate its importance.

Jan 1, 1962

By D. Weinstein

Yieldilzg in annealed arc-cast molybdenunz in torsion was studied as a function of strain rate and tem-perature. The temperature dependence of the yield point for different strain rates was used to calculate a heat of activation for the yield point. The heat of activation was not a constant but was approximately a linear function of the stress at yield. It is proposed that the rate effect in yielding is determined in part by a site place-change of C (or other interstitial atom) in the metal. THE low-temperature embrittlement phenomenon in metals and alloys has been known to exist for a long time. Although a transition from ductile to brit-tle behavior has been observed in some close-packed hexagonal metals1 and a face-centered cubic alloy, the most common class of metals exhibiting this be-havior has a body-centered cubic lattice structure. For example, a ductile to brittle transition has been observed in iron,3 molybdenum,4 chromium,5 colum-bium,6 and tungsten.7 In the present investigation, molybdenum specimens were tested in torsion over a wide range of temperatures at three widely separated strain rates, and the temperature for onset of embrittlement was determined. Characteristic of body-centered cubic metals and closely associated with plastic deformation is the appearance of a sharp upper and lower yield point. Theoretical explanation of the yield point in iron and low-carbon steel is due to Cottrell,8 who attributes the phenomenon to the pinning of dislocations by the formation of impurity atmospheres around the dislocations. These atmospheres tend to lock the dislocations and make them more difficult to move. The stress required to move a dislocation and thereby cause plastic deformation is greatly increased, and thus an upper yield point is observed. In addition, theoretical analysis,9 as well as experimental observations, show that the upper yield point is strongly a function of temperature. The upper yield point is observed to decrease with an increase in testing temperature, and above a certain temperature (-700° K in iron) it no longer appears. This is consistent with the concept that thermal vibrations will help free a dislocation from its atmosphere, so that the external stress required to free a dislocation from its pinning atmosphere decreases with increasing temperature. Furthermore, with increasing temperature the equilibrium concentration of impurity atoms around a dislocation decreases exponentially with the result that the dislocation is less firmly pinned. In Cottrell&apos;s theory of yield point a static model is visualized in which the pinning atmospheres, particularly interstitial atoms, are immobile, and the dislocations are anchored to stationary positions in the lattice. However, experiments1,7 show the upper yield point to be time-dependent or a function of the rate of straining, a high strain rate causing a high upper yield point. Present theory does not adequately account for the rate dependence of the yield point, and the exact function of the interstitial atom is not under stood. Nevertheless, observation of the temperature dependence and rate dependence strongly suggests that the upper yield point phenomenon is due to the interaction between dislocations and pinning atoms, and that a diffusion mechanism is important in determining the yield point.

Jan 1, 1962

By L. A. Roe

The year 1867 marks the first year of commercial production of phosphate rock in the United States. South Carolina produced almost all of the domestic output of mineral phosphate until phosphate mining began in Florida in 1888. During the period 1868 to 1949 the total marketed production of domestic phosphate rock was about 186 million long tons of which 71.5 percent was produced in Florida, 18 percent in Tennessee and 7 percent in South Carolina (1). From 1949 through 1960, Florida phosphate rock production has ranged Prom 71 to 77 percent of the total domestic production. Since three-fourths of the domestic phosphate production is from the Florida field, and since most of the phosphate from the Tennessee and Western fields is not processed, but used directly as electric furnace burden, this paper will concern itself almost entirely with water requirements for mining and processing ore from Florida. Figure 1 summarizes phosphate rock production for Florida vs. total United States production over the period 1947-1960.

Jan 1, 1962

By Richard S. Watt

The Bureau of Mines is often called upon to analyze the demand for various minerals and fuels and to make projections of the future demand. Because minerals and fuels are raw materials and because the demand for raw materials [pends] on the demand for finished goods, these projections are usually [conned] with derived demand rather than final demand. In order to obtain quick [d] reasonably accurate analyses of the demand for mineral commodities, the [reau] developed a method and has used it successfully (31).4 To illustrate the [thod], this report presents a full analysis of the demand for a mineral commodity with enough general theory to permit application of the method to any mineral. Sodium chloride (common table salt) was chosen as the subject of the analysis because the demand for it is less complicated5 and permits a simple application and clear presentation of the method.

Jan 1, 1962

Jan 1, 1962

By Robert E. Johnson

THE MILDEST recession of the postwar period ended in the first months of 1961, and the economy climbed steadily during the remainder of the year. The Federal Reserve Board (FRB) Index of Industrial Production climbed from a low point of 102 (1957=100) in February to 115 in December, a rise of 12.5 percent. But economic activity for the year as a whole was only 1.5 percent higher than the 1960 level, as measured by real gross national product (GNP). Although activity increased throughout 1961, much of it was merely regaining ground lost in the decline during the second half of 1960 and the first months of 1961. The FRB index did not re ain the July 1960 high of 110 until June of 1961. Mineral fuels did not fully share in the economic recovery. The (FRB) crude oil and natural gas index rose only 5 percent between February and December. Although the index of monthly coal production increased 11.5 percent during the year, the February level was so low that total production for the year was the lowest since 1954. Total production of energy measured in Btu&apos;s was up slightly (1 percent) during the ear. Coal production was down; production of crude oil and natural gas was up. Calculated consumption paralleled production-total up slightly, coal lower, and crude oil and natural gas higher. The most interesting product developments were in coke and residual fuel oil. Sales of coke showed a sharper drop than steel

Jan 1, 1962

By D. W. Bridges

Solvent extraction has become important in recent years as a unit process in extractive metallurgy. The flexibility and simplicity of the technique have attracted widespread attention, and numerous papers describing actual and projected metallurgical applications have been published. However, differences in terminology, procedure, objectives, and standards, as reflected in reports by different operators and investigators, have sometimes made appraisals and comparisons difficult. Consequently, a need appeared for n series of basic reports on the subject. This Bureau of Mines Information Circular is the first of such a series. It deals with the status of solvent extraction in metallurgy, as well as with the rudiments and terminology of the unit operation. In analytical chemistry, extraction of molecular species from aqueous media by immiscible organic solvents has been used for many years to separate and determine chemical elements (61).4 Complex chlorides of iron and other metals are readily soluble in ethers and ketones, as are the nitrates of uranium and thorium. Most metals are extractable as complex salts of some organic reagent, such as dithizone, 8-hydroxyquinoline, or cupferron.

Jan 1, 1962

By John Chipman

HE lecture on &apos;Thermodynamic Properties of Blast Furnace Slagso prepared in 1959 and published two years later required revision in one particular before it appeared in print. The activity of SiO, was deter mined through studies of the equilibrium: SiO, (in slag) 2C (graphite) = (in Fe) 2C0 (1 atm) The ratio for each experimental temperature was found from the heat of formation of cris-tobalite, the entropies and heat capacities of the re-actants, by virtue of the third law of thermodynamics. Discrepancies between several kinds of data led to investigations regarding other equilibria involving SiO, on the suspicion that there might be an error in the third-law value of its free energy. In particular the equilibrium: was restudied by Kay and Taylor who Confirmed the earlier results of Baird and Tayloron which their SiO, activities depended. The free energy of Sic was also rechecked4 independently. These and other equilibrium measurements led to the conclusion6 that the free energy of SiO, at high temperatures is in error and requires a correction of about -5 kcal. The exact source of the error is uncertain; it could lie either in the entropy of SiO, or in its heat of formation, but it more probably lies in the latter. Adjustment of this free energy lowers the ratio by a factor of approximately 4. Accordingly it will be necessary to multiply by this factor all of the SiO, activities determined by this method.&apos;,B Referring to the lecture cited, this correction should be applied in Figs. 8, 9, 10, 19, and 20. It applies also to the experimental data of Fig. 13, bringing these as well as those on the ternary system into good agreement with the work of Taylor and associates. At the same time it eliminates the discrepancy shown in Fig. 11, lowering both lines until the upper

Jan 1, 1962

By E. W. Johnson, M. L. Hill

Equilibrium concentrations of hydrogen in iron were measured at H2 pressures up to 136 atm and temperatures down to 145°C. Residual hydrogen was prominent near 600°C in air-melted but not in vacuum-melted iron. The diffusible hydrogen solubility is abnormally high below 390°C, confirming the hypothesis of hydrogen trapping.&apos; It appears that the traps for hydrogen in iron form suddenly on cooling. The estimated H2 pressure in equilibrium with 5 ppm hydrogen in steel at room temperature is less than 1000 atm. It was shown previously1 that the diffusivity of hydrogen in a-Fe below 200°C is anomalously low, a behavior attributed to the presence in the metal structure of hydrogen "traps." The energy of the trapped hydrogen was computed as 4.8 kcal Per g-atom below that of the interstitially dissolved hydrogen. The strongest confirmation of the trap hypothesis should be obtainable from measurements of the hydrogen solubility at low temperatures. such measurements have been performed and are reported in this paper. The "residual hydrogen" effect1&apos;&apos; must be carefully controlled if valid measurements of the solubility are to be obtained, and such an effort was made in the present work. Previous data for the solubility of hydrogen in iron have been summarized by Geller and Sun.3 Their equation for the most probable solubility at 1 atm in a-Fe above 400°C is

Jan 1, 1962

By A. B. T. Werner, J. J. Schanz

A survey of the world&apos;s sources and markets for natural graphite and some predictions of future trends are presented here. The authors feel that there is no indication of major changes in sources of graphite over the next few years, but it is possible that the importance of domestic graphites as opposed to foreign carbons may increase in the more distant future. U.S. consumption of natural graphite, which has been in general decline for the past six years, and will probably continue downhill with the virtual disappearance of some markets. However, other markets such as bearings, brake linings and crucibles will probably grow. Natural graphite is the name given to all the naturally occurring mineral forms of carbon that crystallize in the hexagonal system. Natural graphite~ are generally divided into three broad classifications that are based on physical rather than chemical differences — crystalline flake, Ceylon amorphous and other amorphous. Crystalline flake graphites occur as thousands of small individual flakes disseminated throughout the ore and closely resemble shiny black fish scales. Ceylon amorphous graphite is mined from narrow veins of almost pure mineral. It is produced in lump form and often has a coarse platy or needlelike structure. Other amorphous graphites include all those that are extremely fine-grained and have a crystalline structure that is not visible under normal circumstances. In the primary raw material markets, the graphite&apos;s country of origin is also important. Crystalline flake graphites may, for example, be of the Alabaman, Bavarian or Madagascan types; Ceylon amorphous graphite may have originated in Montana or Ceylon; and other amorphous graphites may come from Mexico, Hong Kong or Korea. The distinctions between the graphites from each particular locality are small yet important, for the country of origin will signify certain inherent physical characteristics and will often give an idea of the amount of graphitic carbon contained in the shipment in question. .In certain instances, however, even this is not enough, since the actual mine at which the graphite is produced may have to be known before its true commercial value can be ascertained. Thus, the Madagascar flake graphite shipped from the Sahalambo mines of the Societe des Graphites de la Sahanavo is a thick flake which is known to be especially suited for use in crucibles, while the dull black earthy amorphous material formerly mined at Cranston, R.I., was ideal for stove polish. Synthetic, artificial, electric furnace and manufactured are terms used to describe graphites made from coke. These graphites will be considered in this paper only to the extent that they enter competition with natural graphite. DOMESTIC SOURCES OF NATURAL GRAPHITES Natural graphites have been produced from mines in Alabama, Alaska, California, Georgia, Montana, New Jersey, New York, North Carolina, Pennsylvania, Rhode Island, Texas and other states. The exception is the crystalline minerals resembling Ceylon graphite that have come from Montana and the amorphous meta-anthracites from Rhode Island. All the products mined have been flake graphite. In 1960, production was reported only in Texas and Pennsylvania. The Alabama graphite deposits of flake in quartz-mica schists are found southeast of Birmingham in a narrow belt that extends for about 60 miles southwest from Delta in Randolph County to Verbena in Chilton County. Since the long-run prospects for Alabama graphites appear to be fairly bright, especially if regular production of high quality output becomes possible, regional ore reserves of all kinds, including indicated and inferred, are estimated to be of the order of 25 million tons. Of this amount, 14 million tons are of the weathered variety. Alabama graphites are favored by their relative ease of mining, and by the fact that special methods of milling have been developed at the larger properties. In addition, the steady rise in ocean freight rates for Madagascar graphites, the tendency among crucible manufacturers to use flakes of a smaller size, and the possibility of producing other salable byproducts in addition to the graphite are favorable to Alabama producers. Against

Jan 1, 1962

By G. R. Rigby

Used basic brick taken from copper anode furnaces, reverberatory furnace roofs, md copper converters have been examined by chemical analysis, petro-graphical examination, and X-ray diffraction tech-niques. In the anode furnace roof, brick absorb copper and copper oxides, whilst in the reverberatory roof, iron oxide with smaller amounts of alumina and silica are absorbed. Chemical reactions in the converter are most complex since the brick absorb both a copper-copper oxide slag and a fayalite-magnetite slag. CHANGES taking place in basic brick after use in copper smelting furnaces have received attention from C. Burton Clark and J. Spotts Mc Dowell,&apos; who examined brick taken from copper converters, and by G. R. Rigby and B. G. Hamilton&apos; who examined brick from copper anode furnaces. This paper describes the changes taking place in basic brick from all types of copper smelting furnaces and discusses the major reasons for lining wear. A) METHODS OF EXAMINING SAMPLES A variety of used brick have been taken from the following positions in various furnaces, a) roofs, reverberatory arches, and bottoms of copper anode furnaces, b) roofs of copper reverberatory furnaces and c) the tuyere line and end walls of copper converters. The method of examination was standard in that brick were first measured and the extent of wear-back computed. They were next sawn in two by a central cut vei-tical to the working face to enable the freshly cut surfaces to reveal any zonal changes and cracks, both of which usually ran parallel to the working face. Each well-defined zone was then sampled for a) chemical analyses, b) petrographical studies using transmitted and reflected light techniques under the microscope, and c) X-ray diffraction studies on powdered samples. From the data accumulated, changes taking place in a variety of

Jan 1, 1962

By David J. Mack, T. V. Philip

The effects on the Cu-A1 eutectoid transformation of the addition of a third element from the second long period and from Group IIB of the periodic table, were studied by isothermal transfomation techniques. The valency of the third element shows the most pronounced effect on the eutectoid decomposition. With some exceptions, the atomic size factor of the third element shows some consistent effects on pearlite nucleation and growth. The atomic concentration or the electronegative valency of the third element shows wo consistent effect on the eutectoid decomposition. Addition of the third element helps spheroidization of pearlite. SINCE the pioneering work of Davenport and Bainl on the eutectoid decomposition in steel by the isothermal transformation technique, an enormous amount of data has been accumulated on the eutectoid transformation characteristics of commercial steels. While the eutectoid reaction in steel is of tremendous industrial importance, it appears to be quite unique among the eutectoid reactions. Though the metal-lographic structures developed in the Fe-C and Cu-A1 eutectoids are similar, it is now evident that the two eutectoid reactions are quite dissimilar. The eutectoid decomposition in the Cu-A1 system is more complicated partly due to the appearance of transitional phases in addition to the equilibrium phases. * The first isothermal studies of aluminum bronzes were made by Smith and Lindlief2 and later by Mack,3 Klier, and Grymko,4 and recently Hayne 5,6 A few other systems, structurally analogous to the above, have been studied by the same technique.7-10 Kasberg and Mack1&apos; studied the effects of iron on the transformation of commercial aluminum bronze. The effects of manganese and nickel on this aluminum bronze and those of iron, manganese, and nickel on the binary Cu-A1 eutectoid have been recently studied.12 The object of the present investigation was to study, by isothermal transformation techniques, the effects (with respect to the fundamental factors of alloy formation) of the addition of a third element on the transformation of a Cu-Al eutectoid alloy, 11.8 pct Al. The third elements chosen for the purpose were silver, cadmium, indium, tin, and antimony from the second long period, and beryllium, zinc, and cadmium from group 11B of the periodic table. They were added in nominal amounts of 0.5, 1.0, and 2.5 pct by weight to a eutectoid Cu-A1 alloy. These third elements were expected to show the effects of electron valency, atomic size factor, and electronegative valency effects on the binary eutectoid transformation. PFLEPARATION OF ALLOYS AND PROCEDURE All alloys were made as 400-g heats by induction melting in a graphite crucible with a graphite lid. The molten alloy with a layer of graphite powder on top was stirred at regular intervals by a graphite rod. When the melt was judged to have acquired sufficient superheat, a pinch of common salt was sprinkled on top and any crust scraped off to one side. It was then chill cast into a 5/8 in. rod. The alloys with silver were prepared by remelt-ing the high-purity Cu-A1 eutectoid alloy used by Mack3 with high-purity silver (99.99 pct pure from Hardy and Harmon, Inc.). In the preparation of all the other alloys, polished electrolytic copper shot (from Belmont Smelting and Refining Co.) and high-purity aluminum (99.99 pct pure from Aluminum Co. of America) were used.

Jan 1, 1962