Search Documents

By Jean Howard

ThE formation of the (100) [001) texture in 3-1/4 pct Si-Fe strip was first reported by Assmus ef a1.l in 1957. Since then much experimental work has been carried out with a view to establishing the mechanism involved. The papers cited above state that the (100) [001] texture was developed in strip rolled from material melted and cast in vacuum. (The impurity content of the ingot is reported as 0.005 pct.) The present note records that similar results can be obtained in material processed by powder metallurgy. A processing schedule is described.which enables the texture to be formed in strip up to 0.010 in. thick, but there seems no reason why this should not be achieved in thicker strip, provided that large grains are developed after sintering. The materials were prepared from Carbonyl Iron Powder Grade MCP (particle size 5 to 30 p) of the International Nickel Co. (Mond) Ltd. The powder contains about 0.15 pct 0, 0.01 pct C, 0.004 pct N, <0.002 pct S, $0.005 pct Mg and Si, and 0.4 pct Ni— that is, it is substantially free from metallic impurities other than nickel, which is thought to be unimportant in the present work. The silicon powder was 99.9 pct purity, or material of transistor quality (ground in pestle and mortar). The mixed powders (3-1/4 pct Si to 96-3/4 pct Fe) are heated in hydrogen at 350" and 650°C to deoxidize the iron before sintering loose at temperatures between 1350" and 1460°C (depending upon the ultimate thickness of strip required) for up to 24 hr. The object of the high-temperature sinter is to develop a large grain size at this stage. Alternatively, the loose sintering can be done at a lower temperature followed by rolling or pressing and then annealing at temperatures between 1350" and 1460°C. Both methods produce large grains, which remain large throughout the process. The compact is then hot-rolled to approximately 1/8 in. with high-temperature interstage anneals if necessary. This step is taken to avoid intercrystalline cracking which would occur if the material of such large grain size were cold-worked. The bar is then annealed at 1050°C and reduced to its final thickness by approximately 50-pct reductions and 1050°C interstage anneals. Throughout the process the dew point of the hydrogen furnace atmosphere is maintained at about -40°C. Samples were annealed in hydrogen at various temperatures and times. Secondary recrystalliza-tion to (100) [001] was developed on the thinner material (i.e., up to 0.002 in.) by annealing in hydrogen at 1050" to 1200°C with a dew point of - 40°C or in vacuum (10-5 Torr) at 1050°C. With the thicker materials (i.e., up to 0.010 in.) the best results were obtained by annealing in hydrogen at 1200°C with a dew point of - 55°C. Complete secondary recrystal-lization to (100) [001] textures was obtained. Above these temperatures secondary recrystallization to (110) [001] tended to develop. The final annealing of samples was normally carried out with the samples placed between recrystal-lized alumina plates, but some experiments were performed with the samples suspended so that their surfaces were not in contact with anything except hydrogen, and these were equally successful in developing secondary crystals. An approximate determination of the proportion of material (before secondary recrystallization took place) having crystals with the (100) or (110) planes in or near the rolling plane showed that 11 pct of the sample had (100) and 16 pct (110). The method used for the determination is described below. A sample was annealed at a temperature just below the secondary recrystallization temperature and etched to reveal the (100) planes. The approximate area covered by crystals having (100) or (110) in or very near the surface was measured on the screen of a Vickers projection microscope. This was repeated for twenty positions chosen at random and a mean of the results calculated. The main hindrance to developing the secondary crystals in the thicker materials was the difficulty of obtaining a large enough initial primary grain size before secondary recrystallization. This was overcome by increasing the particle size of the silicon powder used. During the course of the work, it had been observed that the larger the grain size after sintering the more likely it was that the material would be successful in developing secondary crystals at a later stage. An experiment was therefore carried out to determine whether the material with the larger grain was more successful in developing secondary crystals due to the large grain produced at the sintering state per se or whether it was due to the greater reduction of silica brought about when the sintering temperature was raised in order to increase the grain size. A comparison was made between two compacts, one of which was made with silicon powder of 60 to 100 mesh, the other with silicon powder which was finer than 200 mesh. F?r this experiment, use was made of a phenomenon previously observed that the larger the particle size of the silicon powder employed in making a compact, the larger is the grain size of the compact. The silicon powder was ground

Jan 1, 1964

By Nicholas J. Grant, Raymond E. Cairns

A high-purity chromium, made by solid-state extrusion, and a series of molten, extruded, dilute alloys containing carbon, oxygen, nitrogen, and sulfur were studied to establish the effects of composition, cooling rate, grain size, strain rate, and prior strain on the transition temperature for brittle THE transition from ductile to brittle fracture with decreasing temperature remains of extreme interest especially among the refractory metals, such as tungsten, molybdenum, and chromium, which have relatively high transition temperatures. Fracture, yield stress, and hardness. Tension tests at a strain rate of 0.015 per min were generally utilized. Results are interpreted in terms of the quantity of each element retained in solid solution. Of these elements, chromium has been studied the least, but deserves additional attention because of its superior oxidation resistance for high-temperature use. In the past, impurity elements which have received attention are carbon, nitrogen, oxygen, and sulfur;&apos;-&apos; of these, nitrogen has usually been considered to be the most detrimental. Unfortunately, because of different levels of both specific and total impurity content, and because of the many different test and evaluation techniques used, a clear, definitive picture of brittle fracture in chromium has not been forthcoming. However, many

Jan 1, 1964

By D. D. Pollock

The resistivity, temperature coefficient of resistance, and absolute thermoelectric properties of some binary terminal solid solutions of silver were determined. Equations are given which permit the calculation of these properties. CONSIDERABLE work has been done on the constitution and electrical conductivity of binary alloys of silver.1-l2 Some of these alloy studies are apparently complicated by doubtful chemical analyses. In some cases the limits of solid solubility are questionable. Those references which present electrical properties of binary silver alloys usually give just one particular set of characteristics such as conductivity (or resistivity). As a means of checking and extending this earlier work, an investigation was undertaken to describe and calculate the resistivity, temperature coefficient of resistance, and thermoelectric power of binary terminal solid solutions of silver. PREPARATION OF ALLOYS All of the alloys were made with silver containing less than 0.014 pet (by weight) of impurities. These materials were carefully weighed out into 225-g heats and melted in a high-frequency induction furnace. The indium, tin, and antimony systems were melted in Al2O3 crucibles, under a boric anhydride cover, and poured into split graphite finger molds. The aluminum, germanium, arsenic, lead, and bismuth alloys were melted in machined graphite crucibles, and they were also covered with boric anhydride and poured into split graphite finger molds. The alloys containing magnesium and manganese

Jan 1, 1964

By R. A. Wood, R. I. Jaffee, H. R. Ogden, D. N. Williams

CERTAIN titanium alloys when quenched to retain the 0 phase at room temperature show extensive transformation of 0 to martensitic a during deformation. Alloys of this type are usually characterized by low tensile yield strength, a large spread between yield strength and ultimate strength, and high uniform elongation. A previous investigation of this phenomenon concluded that the principal contribution of the martensitic transformation was to increase the amount of deformation prior to fail-

Jan 1, 1964

The addition of a thallous salt to the cyanide leach of a calcined pyritic concentrate causes a marked increase in the rate of extraction of gold. This is due probably to the activation of passive gold by the thallous ions. Lead, bismuth, and mercury salts, which should produce a similar effect, fail to do so. It is postulated that this latter result, together with the reprecipitation of silver at low cyanide levels, is due to the presence of soluble sulphide.INTRODUCTIONThe work of Fink and Putnam (1950) showed that the rate of solution of gold in cyanide can be increased by the addition of small amounts of lead, bismuth, mercury, and thallium salts. Mills (1951), during a study of the electrochemistry of gold, with particular reference to cyanidation, was able to show that gold may become passive towards cyanide solution. The addition of lead or thallium salts prevented this passivity, although the action of lead was limited to the pH range 10 to 12. In a recent paper Cathro (1963) confirmed the findings of Mills, and presented results which showed that the addition of thallium to a cyanide leach of a calcine from Lake View and Star mine, Kalgoorlie, increased the rate of extraction of gold appreciably. In, this paper the use of thallium to prevent the gold becoming passive, and hence to decrease leaching time and cyanide consumption, is examined.EXPERIMENTALA series of leaching tests was carried out on a sample of Lake View and Star calcine, comprising calcined pyrite (about 70 per cent.) and siliceous gangue (about 30 per cent.) and containing 165 p.p.m. gold, 45 p.p.m. silver, 0&#183;1...

Jan 1, 1964

By J. Wade Watkins

One potential peaceful application of nuclear explosives is stimulating the production of liquid or gaseous hydrocarbons from essentially nonproductive deposits of petroleum, natural gas, oil shale, and tar sands. Within the United States the appreciable difference between producible proved reserves and ultimate reserves and resources of hydrocarbon deposits is of such magnitude that much petroleum, natural gas, shale oil, and bitumen will not be produced unless significant technological progress is made in production techniques. The shattering effect of contained nuclear explosives and, to a lesser extent, the heat produced, have been considered as stimulative forces when the thickness, depth, and nature of such deposits permit considering the use of nuclear devices. Mechanical production problems would be less in an oil or gas reservoir than in an oil-shale or tar-sands deposit. Also, tar-sands resources in the United States may not be adequate to warrant serious consideration of applying nuclear-explosives stimulation. Gas reservoirs should present the least- radioactive-contamination problem. The technical feasibility of using nuclear explosives cannot be evaluated fully at present. Additional information is needed on the effects of pressure, heat, and radioactivity on the solids and fluids of hydrocarbon deposits, the nature and extent of induced fractures in different rock media, and the possibility of isolating and confining or removing radioactive contaminants. Final technical feasibility can only be determined by a field test. If technical feasibility is established, economic feasibility will depend upon the comparative cost of producing hydrocarbons by nuclear explosives and by conventional means. It is probable that an economic comparison would favor nuclear stimulation only where devices of relatively high yield could be used practicably and safely.

Jan 1, 1964

By K. J. Brondyke, P. D. Hess

Two processes have been developed for improving the quality of molten-aluminum alloys before casting. The Filtration Process. which involves passing molten metal through a packed bed of granular filter material, is a rapid means of removing finely divided particles. It has the most potential in those instances where removal of inclusions is of primary importance. The Combination Fillration-Inert Gas Fluxing Process inuolzles introduction of an inert gas so that it will diffuse countercurrent to metal flow through the filter bed of granular material. Dissolved hydrogen is removed from the metal in addition to removal of finely divided particles. The Combination Process is most useful where both inclusion removal and attainment of conistently low-hydrogen-content metal are important. Metal treated by the Combination Process is of higher and more uniform quality than heretofore attainable with prolonged chlorine fluxing. Costs of the Combination Process can, for the most part, be offset by savings derived from high recoveries and increased production of superior-quality products. IMPROVEMENT in the quality of molten-aluminum alloys is secured generally through the use of some fluxing practice in a crucible, holding furnace, or ladle involving either gaseous or solid fluxing media. Typical fluxing agents may include the gases nitrogen, argon, or chlorine used either singly or as mixtures and the solids aluminum chloride or hexachloroethane. Regardless of the fluxing means used, the primary objectives are the adequate removal of both metallic and nonmetallic inclusions and reduction of hydrogen content to an acceptably low level. The ultimate goal is to produce ingots and cast products of high quality free from inclusions and porosity. The development of ultrasonics for measurement of internal quality, tightening of quality controls, and the application of the aluminum alloys to new or different commercial fields have been responsible for an ever increasing demand for improvement of quality of both cast and fabricated products. This demand for high quality has not been restricted to any single type of product. On the contrary, the demand encompasses about the entire variety of products including those for fabrication, those to be machined, buffed, or finished for decorative purposes, and those for critical applications where both surface and internal quality is of utmost importance. In many instances products acceptable in the 40&apos;s would now be scrapped as unacceptable by these higher present-day standards. With this ever increasing demand for higher quality, it became apparent at Alcoa that conventional means of melt treatment were inadequate in many instances and new approaches were necessary. Consequently the research program was intensified with attention focused on metal treatment during transfer in order to reduce the furnace processing time to a minimum in an effort to attain the desired results at a minimum of additional expense. As a result of this intensive research program which covered numerous variations and adaptations of conventional methods in addition to new methods of melt treatment, several new processes were developed, two of which will be described here. The first of these, a method of melt filtration, was patented in February, 1959.l The second process involving combination filtration—inert gas fluxing was patented in June, 1962. 2 Other melt-treatment processes developed during this period of investigation were patented as listed.3 FILTRATION PROCESS General Description. The Filtration Process, which involves passing molten metal through a packed bed of granular filter material, is a rapid method of effectively removing finely divided particles. It is an impingement-type filter; hence the size of the particles removed from the metal are considerably smaller than the interstices of the

Jan 1, 1964

By L. A. Panek

Research on roof bolting has developed significant information with respect to the functions that can be performed by properly installed bolts and the methods that can be used to ensure that effective installation has been achieved. The present paper brings together results that are pertinent to the design of a bolting system for reinforcing horizontally stratified mine roof with vertical bolts. The design approach is based on the use of bolts to decrease the maximum bending stress within an arbitrary sequence of roof strata (see Fig. 2) in which the only loads are the weights of the individual beds. The use of rock bolts to achieve other objectives, such as to stabilize a fractured rock mass on the periphery of a mine opening,3 is excluded from consideration herein. Reinforcing effect of bolts consists of a friction effect and a suspension effect in combination. "Friction effect" refers to reduction of bending in a stratified roof due to clamping action of tensioned bolts, which compress the strata, thereby creating frictional resistance to displacement along planes of stratification. (The flexure of a sequence of strata is necessarily accompanied by horizontal displacement of each bed with respect to its neighbor, along mutual surfaces of contact.) Although the sliding of the beds tends to exert a shearing effect on the bolts, tests show that this has negligible influence on the bending stresses, probably because the bolts are so far apart. "Suspension effect" refers to the transfer of part of the weight of the weaker or thinner strata to one or more thick strata, which occurs when strata with differing tendencies to deflect are constrained to have equal deflection. The term "suspension" is used irrespective of whether the thin strata are above or below the thick strata, because tests show that the supporting effect of the flexurally more rigid roof strata is for practical purposes independent of their position in a bolted sequence of strata. An earlier paper4 dealt with a bolted unit in which all strata had equal flexural rigidity; bolting could develop a friction effect but no suspension effect. The present paper deals primarily with a bolted unit in which all strata do not have equal flexural rigidity, so that bolting can develop both a friction effect and a suspension effect. The reinforcing effect of the bolts was determined by a combination of experimental and theoretical stress analysis.4&apos;6&apos;7 The experimental method consisted of loading a model by rotating it in a centrifuge to simulate the gravity forces exerted about an underground excavation. Models were made from two different limestones, although the results are independent of the material because the elastic constants were taken into account in the data analysis. Electric resistance strain gages were bonded to the highest and lowest members of the bolted unit to determine the outer-fiber bending strains at the center and at the supports. The quantitative results presented herein are based on tests of 56 different models, which included a range of values for the structural parameters. Each model was tested several times, with different combinations of spacing and tension of the bolts. DESIGN EQUATIONS The effects of friction and suspension on the flexure of a bolted stratified roof can be expressed by the following equations, which give the maximum bending stress, the deflection, the friction effect, the suspension effect and the transferred load for any (the i-th) member of the bolted unit in terms of the structural parameters:

Jan 1, 1964

By David P. Shoemaker, Clara B. Shoemaker

It has been shown for an important class of complex transition intermetallic compounds (a, P, R, 6, and p phases) characterized by "normal" coordination [CN12 (icosahedral), CN14, CN15, CN16/ that interatomic distances nay be calculated to a good approximation as the sum of characteristic atomic radii. Two radii, one for major ligands and one for minor ligmds, are specified for each atom, except in the case of CN12 where only a miaaor-ligand radius is specified. The same appears to be true of transition-metal phases of simpler struc-ture: Laves phases (CN12, CN16), and p-tungsten phases (CN12, CN14). In the case of known examples of the more complex phases, a simple rule is given which specifies these radii. However, only a fraction of the known examples of the simpler phases obey this rule closely. To include the latter phases the rule may be modified by considering the radii as linear functions of the weighted average of the Pauling CN12 radii of the two kinds of atonzs, with the radii weighted according to the over-all chemical composition of the alloy. With very few exceptions interatomic distances for both tlze complex and the simpler transition phases can b$ predicted with this modified rule to within 0.06A. ManY intermetallic compounds are known of composition A,By, in which A is a transition element to the left of the manganese column in the periodic table and B is a transition element in or to the right of it. Frequently the coordination numbers (CN) found in these compounds are CN12 (icosahedral), CN14, CN15, and CN16 (called "normal" coordinations by Frank and Kasperl). Well-known examples are the cubic and hexagonal Laves phases which have CN12 and CN16, and the 0-tungsten (CrsO) phases which have CN12 and CN14. In the more complicated (often ternary) phases, such as the a phase,2 the Beck phases p3 and R~, the 6 phase,5 and the p p atoms occur with CN12, CN14, CN15, and (except for a) CN16; in many cases several crystallographically independent atoms of one particular CN occur in the asymmetric unit. A large number of independent interatomic distances are found in these complicated phases, varying from 20 in the a phase to 94 in the 6 phase. These distances show a large spread; they vary, for example, from 2.358 to 3.278A in the 6 phase. In our analysis of these distances we found that in each of these compounds every atomic position can be characterized by either one or two radii. The CN12 positions are characterized by a single radius, The higher coordinated positions are characterized by two radii, namely: the CN14 positions by 4 in the direction of the twelve "5-coordinated" ligands3 (called &apos;minor" by Frank and Kasperl) and by r:, in the direction of the two "6-coordi-nated" ligands (called "major" by Frank and Kasper); the CN15 positions by r15 for the twelve minor and r:, for the three major ligands; the CN16 positions by rlE for the twelve minor and r:, for the four major ligands. We have expressed the experimentally determined interatomic distances in observational equations as the sums of the appropriate pairs of these characteristic radii and the value of these radii have been determined by the method of least Squares. Despite their wide range, the interatomic distances could then be predicted by the sums of these atomic radii with an average deviation in any one compound of 0.06A or less. The results are summarized in Table I. Inspection of the radii thus obtained shows that in the structures in Table I the radii (in A) are given to a first approximation by the simple relationship: Where CN is the coordination number (12, 14, 15, or 16), and A = 1 for major ligands and = 0 for minor ligands. The interaLomic distances can be predicted within about 0.1A by sums of these atomic radii. Another phase belonging in this group with CN12, 14, 15, and 16 is the y phase & B7, in which A is molybdenum or tungsten and B is iron or cobalt. Recently the M%C phase has been refinedE and the observed distances also agree well with those calculated with Eq. [I]. (In the original determination of the structure of W6FeV7 the F$(II)-W(II1) distance was erroneously given as 2.84A, but we have recalculated it fro? the published parameters and found it to b? 2.57i4, in good agreement with the value of 2.6A predicted with Eq. [I.].) Many binary transition alloys are known to crystallize with the simpler structures having "nor-

Jan 1, 1964

By J. S. Ross

The significance and role of industrial minerals in Canada differ from those in the United States, The smaller Canadian industry has recently become well diversified and self-sufficient in most commodities, However, it depends on exports, principally to the United States, for much of its market, Imports are small, but imports of several basic products manufactured from industrial minerals are large. This nation is a leading world producer of asbestos, gypsum, sulphur, nepheline syenite, titania slag, potash and barite. It has reserves in asbestos for at least 30 years enough potash to supply the current world&apos;s needs for 2,000 years and sulphur reserves for 40 years of current world demand, One of the ilmenite deposits contains enough titania to supply the current world demand for at least, 25 years.

Jan 1, 1964

By T. D. Tiemann

Extraction of silica from the taconites of the Wisconsin Gogebic range by high temperature digestion in caustic solutions has been described.1,2 The ores consist essentially of hematite, goethite, and microcrystalline quartz, detailed descriptions of which appear in the literature.1,3 It is the purpose of this communication to describe some results obtained from a laboratory investigation of an alternative method, that of sintering the ore with sodium carbonate followed by water extraction of the sodium silicate produced. This is analogous to the Deville-Péchiney4,5 soda ash sinter process for the production of alumina from bauxites in which soluble sodium aluminates are formed. Raw mixes of the desired composition were prepared from 10.0 g minus 200 mesh samples of taconite and sintered in nickel crucibles in a muffle furnace controlled to within ±10°F of the operating temperatures. The resulting sinters were pulverized and then leached in distilled water with continuous agitation for 30 minutes at 95°C. The suspensions were vacuum filtered and the residues dried, ignited and weighed. Iron assays on the ignited samples were made by the standard dichromate procedure after dissolution in hydrochloric acid. The percentage of extraction was calculated from the iron assays by the relation:

Jan 1, 1964

By Robert E. Green, Robert A. Swanson

Ultrasonic attenuation and stress were measured simultaneously as a function of strain for aluminum single crystals tested in compression. The propagation mode and polarization of the ultrasonic waves were chosen with reference to the theoretical analysis presented in Part I. Good experimental agreement was found with this theory and with earlier experimental work in tensile tests. Support is given to the contention that ultrasonic -attenuation measurements are much more sensitive to the early stages of plastic deformation than are conventional stress -strain measurements. Dislocation meclzanisms are suggested which are compatible with both the present and the earlier experimental observations. A brief historical introduction of previous work concerned with the study of dislocation motion by ultrasonic-attenuation measurements has been given in Part I. The purpose of the present experimental investigation was to make use of the theoretical considerations from Part I in order to gain further knowledge concerning dislocation motions during plastic deformation. Emphasis was placed on the choice of propagation modes and polarization of the waves, such that interactions between these waves and dislocation movement on a specific slip system could be investigated. EXPERIMENTAL PROCEDURE Since the primary concern of this investigation was dislocation damping, other sources of damping were eliminated as much as possible. The test specimens were 0.5-in.-diam single crystals of 99.99+ pct pure aluminum grown from the melt by a modified Bridgman technique. Ultrasonic-attenuation measurements were made at a frequency of 10 megacycles per sec using a Style 56A001 Ultrasonic Attenuation Comparator manufactured by Sperry Products Inc. after a design by Chick, An- derson, and Truell.1 At this frequency the particle vibrations are essentially adiabatic and thermo-elastic damping should be absent. This frequency was selected since it was one of the frequencies used by Hikata et al.2 n conjunction with tensile tests on aluminum crystals, thus allowing direct comparison with this work. The use of quartz-crystal transducers insures that the amplitude of vibration is not sufficient to cause the break away of the dislocation loops from weak pinning points. The quartz-crystal transducers used all possessed a resonance frequency of 10 megacycles per sec and were thin circular discs 0.375 in. in diameter. X-cut crystals were used to generate the longitudinal waves and AC-cut crystals to generate the transverse waves. Aluminum was chosen as the basic material because it is a typical fcc metal whose deformation behavior is well-known and because the most recent work at the time the present research was initiated was that by Hikata et al. who used aluminum. The present tests were run in compression to see if such tests could be satisfactorily run in compression without being severely masked by grip effects.. A second reason was to compare the results in compression with those of the tension experiments of Hikata et at. Finally, shorter specimens could be run in compression with less over-all damping than in tension. All of the aluminum-crystal test specimens used were oriented for plastic deformation by single slip; i.e., they possessed the orientation having a maximum Schmid factor of 0.5. Because of the well-known time dependence 3 of plastic strain at constant stress, the test specimens were subjected to a quasi-static loading. Previous investigations4-&apos; have indicated that attenuation after plastic deformation is also time-dependent, so any continuous loading of the specimen would show that changes in attenuation were also a function of strain rate. By loading the specimen to a given stress level and holding it constant until the recovery process was essentially complete, the time dependence was eliminated. The quartz transducer was permanently bonded to the aluminum crystal using Eastman 910 cement. Excess cement was removed from around the quartz with DMF (dimethyl formamide). Eastman 910 was found to be far superior for bonding, especially with regard to the shear-wave transducer, since it formed a solid bond which readily supports shear-wave propagation. The solid bond formed by the Eastman 910 cement also insured that the quartz

Jan 1, 1964

The southern portion of the Swan Coastal Plain, a geomorphological element formed since late Tertiary times, contains commercially exploitable accumulations of ilmenite, zircon, rutile and monazite associated with a series of raised shorelines. The location of the deposits is controlled by a locally outcropping Archaen granite/ granulite complex and a sea current pattern determined by local geography and a prevailing wind direction. A progression from medium to high titanium ilmenite is evident parallelled by progressive leucoxenisation as the age of the deposits increases. Variations in trace element content accompany this process. Circulating groundwater has caused vertical mineralogical variations within individual deposits and by precipitation of iron has formed layers of hardpan.The Geographe Bay deposits are of important economic significance.INTRODUCTIONObservations made during the course of a brief survey of the southern portion of the Swan Coastal Plain provide an outline of the geology and mineralogy of the mineral sand deposits of the area. This preliminary study will require considerable modification in the light of more detailed work in the future.REGIONAL GEOLOGYThe Geographe Bay area is situated in the south-west corner of Western Australia between longitudes 115&#176; O&apos;W. and 116&#176; O&apos;W. and latitudes 33&#176; 15&apos;S. and 33&#176; 45&apos;S.The general geology of the area is shown in Fig. 1 where the control of the physiography exercised by the Cape Leeuwin-Cape Naturaliste basement ridge is readily apparent. Between this ridge and the Precambrian east of the Darling fault lies the southern part of the Perth basin which contains outcropping Jurassic to Recent sediments and lavas (McWhae, et al., 1958).The Leeuwin-Naturaliste ridge is the exposed portion of L Assistant Production Managcr. Laporte Titanium (Aust.) Ltd.

Jan 1, 1964

By Nick Holonyak

Halogen vapor-transport synthesis of Ga(As,-,Px) and its preparation into laser junctions are described. Electrical and optical properties of Ga(As,-,PX) laser junctions are discussed. The present limitations in these properties are related to material proble?vzs and the very early state of development of Ga(As,-,PX), and are discussed in this context. Inhonzogeneity problems, fluctuation of As :P ratio, and problems with deep-level contaminants are described and related to Ga(As,-,PX) junction performance. Laser junctions are demonstrated which operate to wavelengths as short as 6470 A (77°K). The prospect that Ga(As,-,P,) will operate to wavelengths perhaps 100A shorter is mentioned. IN this paper we wish to describe some of the more important features of almost 1 year of experience in the preparation and properties of Ga(As,-,P,) p-n junction lasers. Because much data so far available are far from complete, some of the results still must be considered tentative and subject to correction and revision as work on Ga(As,-,P,) crystal problems progresses. Although the electrical, optical, and device properties of Ga(As,-,P,) junction lasers are understandably of considerable interest, the work to date points out that by far the most serious problems extant and those deserving first attention are problems involving the growth, doping, and perfection of Ga(As,-,P,) crystals. One of the most formidable of these is to grow Ga(As,-,P,) sufficiently free of deep levels, either due to contaminants or to structural imperfections, to allow fabrication of laser p-n junctions which can be cooled and not suffer from "freeze-out" of carriers on deep levels (and consequent double-injection behavior). In addition to the problems of growing crystals adequately free of deep levels and generally of the highest perfection, so that the best possible laser junctions can be realized, the further goal remains of increasing the phosphorus content well beyond 40 pct in an attempt to determine the practical lower wavelength limits of laser action in the Ga(As,-,P,) system. Even though the laser junctions prepared in Ga(As,-,P,) are of importance in their own right, we have considered them at this point mainly a means to study the growth and crystal problems of the material. It can be concluded that the laser junctions now available are almost completely limited by the purity and structural deficiencies of Ga(As,-,P,) crystals, and cannot be fairly compared with, for example, GaAs p-n junction lasers until Ga(As,-,P,) crystal growth has been more extensively developed. The basis for the statements above will become evident in the following sections which describe Ga(As,-,P,) crystal and junction preparation, and laser-junction properties. G(As,-,P,) CRYSTAL GROWTH As previously reported,2 we have found it convenient to employ the halogen vapor-transport process3 for synthesizing Ga(As,-,P,) crystals for use in laser junctions. Commercially available GaAs and Gap, separately prepared by halogen vapor tranport, are sealed in the desired ratio in a quartz vessel with a quantity of column-VI donor and a small quantity of metal halide which supplies the halogen for transport. The sealed ampoule, as shown in Fig. 1, is heated at a temperature in the range from 1025" to 1100°C at the position of the source GaAs and Gap. The GaAs and Gap are simultaneously vapor-transported and deposited as Ga(As,-,P,) at one end of the ampoule

Jan 1, 1964

THE composition and quality of finished steel depend upon selection and proportioning of the raw materials of the charge as well as upon control of furnace practice. This chapter deals only with the raw materials of the basic open-hearth process that are important in determining the composition of the steel or slay. They are the metallic charge, oxygen-bearing materials, fluxes, alloying and deoxidizing additions, and certain refractory materials used for maintenance of bottoms. Other refractories, which may affect the slag composition, are discussed in Chapter 3. Wide variations are possible in the type and composition of charged materials but certain limiting relations among the elements of the charge must be observed. Since the process consists essentially of refining by the oxidation of undesired elements, a balance must be established between the sources of oxygen and the elements in the charge that are subject to oxidation (see Chapters 2 and 7). For example, if it is desired to use a high ratio of blast-furnace hot metal to scrap, it is necessary to add an oxygen-bearing material such as ore or mill scale to eliminate the excess carbon and silicon that are present in the hot metal. An example of the opposite extreme is the use of a metallic charge composed entirely of steel scrap. With this type of charge, it is common practice to substitute burnt lime for limestone as a flux and to charge some carbonaceous material such as coke to avoid an excess of oxygen in relation to the elements of the charge that are subject to oxidation. Elements such as copper and nickel, which are not oxidized or eliminated by any other reaction, may be introduced into the charge only to the extent to which they are permissible in the finished steel. An example of adjustment of the charge for elements of this type is found in the use of steel scrap high in copper. In this case, metallic components of the charge other than the scrap should be low in copper, or a sufficiently high ratio, of pig iron to scrap should be charged to dilute the copper from the

Jan 1, 1964

By G. W. Healy, J. C. Schottmiller

Molten silicates were found to exist in the Cr-Si-0 system at temperatures above 1450°C. one atom of oxygen is readily removed from CrzOs in the presence of Si02 at 1700°C, forming a silicate melt. Steam-hydrogen ratio measurements made at this temperature indicate that the free energy of the reaction: Cr20s(c) + Hz = 2CrO (in Si02 -saturated melt) + H20 is approximately 5600 * 1500 cal. A deep-blue chromous silicate, probably Cr2Si04, forms from these melts at about 1400" to 1500°C, and is characterized by.its distinctive X-ray diffraction pattern and optical properties—distinct pleochroism and high refractive indices. THE question of the state of oxidation of chromium in slags has vexed metallurgists for many years The experiments of Koerber and Oelsenl suggested the probable presence of divalent chromium in silica-saturated slags equilibrated with high-chromium melts. Hilty and coworkers2 had also found chromium at lower valency, as Cr304, in inclusions formed from oxygen-saturated Fe-Cr melts with as little as 10 pct Cr. In both cases, disproportiona-tion of the lower oxide to CraO3 and chromium was found to occur to a greater or lesser extent, depending upon the rate of cooling from the high temperature. The work on Cr304 was sufficiently detailed for chipmans to derive its thermodynamic properties, but Oelsen&apos;s experiments in the silicate system were not extensive enough since most of his runs were made with slags containing large amounts of manganese oxide in addition to iron and chrome oxide and silica. The present study describes experiments carried out to map out an approximate liquidus diagram in the CrzOs, "CrO", SiOa portion of the Cr-Si-0 system, and to measure the partial free energy of solution of oxygen in the system. EXPERIMENTAL 1) Approximate Melting-Point Determinations. Preliminary trials showed that when an equimolar mixture of Cr20s and SiOa was treated with hydrogen in the temperature range 1500" to 1600°C, copious amounts of steam were evolved, and a low-melting liquid formed which could be quenched to a blue, crystalline, material having a distinctive X-ray diffraction pattern. It was found that the identical material could be produced by heating intimately mixed, finely divided Cra03, Cr, and SiOa, held in a tungsten crucible, under purified argon. Thus, it was possible to prepare mixtures containing any desired proportions of chromium, silicon, and oxygen, pel-letize them, heat to temperature in the furnace shown in Fig. 1, and observe, after cooling, whether the pellet remained unchanged or showed signs of incipient, partial, or complete melting. 2) Free Energy of Solution of Oxygen. This was studied by measurement of steam-hydrogen ratios for the reaction: H20 (gas) + O (dissolved in charge) + Ha (gas) The experimental method chosen was to prepare a

Jan 1, 1964

n One of the most interesting and economically important developments which has .`taken place- in the Kalgoorlie Field over the past twenty .years is the proved penetration of ore into - caicò schist. which:has been established on the North Kalgurli Mine. &apos;This is quite extensive, both. laterally and &apos; in -depth, and has occasioned-,&apos;" ccasioned &apos; " some madification.of geological thought In the search for additional ore sources:. .Ore has been mined in calc schist almost since the&apos; first major: gold::discoveries-were made,. and the principal &apos;features of the various types of depos:itl are well covered in the literature &apos; of the field. &apos; However, occurrences in caic schist have not-been characterised by the same degree of continuity or frequency as the innumerable lode formations in- the more -favourable quartz dolerite, &apos; and there has been a tendencyAo regard,them as isolated and discontinuous ore bearing structures, occurring only under very special-- conditions. It is not intended-:to describe the whole&apos; range of caic schist ore occurrences in this paper, but only major controlling structures, whose penetration therein has been definitely established, and in which an appreciable .amount.of,_ore.has, been and is still being. found.. . It is considered that -similar stiiictiires: may present a&apos; major objective for future exploratory work in other parts of the field&apos;.

Jan 1, 1964

By J. Gordon Scott

The Iron Ore Company of Canada has now been operating a computer for the grading or blending of direct shipping ores for two years. This paper deals with the computer application pertaining to the grading of direct shipping ore. It consists of five sections. The first part deals briefly with a description of the operation of the Iron Ore Company of Canada; the second with the source and flow of the various data required to grade or blend ore; the third briefly outlines the computer programs used in this application; the fourth illustrates the mathematical approach used to properly blend ore. The final section briefly describes other technical computer programs.

Jan 1, 1964

By Robert M. Dreyer

In an industrialized nation, as the process of industrialization continues, the ratio of the value of production of non-metallic to metallic minerals normally increases gradually over a period of years. For example, in the United States, the ratio of the value of production of non-metals to metals now is approximately two-to-one. Those of us who come from California like to think that we inherit the mantle of the old hard-rock miner, but the truth of the matter is that, in California, of the total value of mineral production exclusive of fuels, 97% comes from non-metallic - industrial - minerals. Since the industrial minerals furnish a principal source of raw materials for the construction and chemical processing industries and since these two industries, in industrialized nations, generally increase directly with increasing population, the future of industrial mineral production both in the United States and throughout the world is indeed bright. Because of the importance of industrial mineral production, it often surprises those of us in the industrial mineral industry to find that industrial minerals are poorly understood by many of our colleagues in the mining industry. I think that one reason for this comprehension of the industrial mineral industry is that the education of both geologists and mining engineers still markedly emphasizes exploitation of the metals.

Jan 1, 1964

By P. T. Stroup

Jan 1, 1964