Search Documents

Jan 1, 1965

By T. L. Chu, G. A. Gruber

Silica films hare been rleposited 011 silicon substmtes at 400° to 600°C by a chemical-transport technique using hydrogen fluoride as the transport agent ill a closed system. This transport takes place from a source materia1 1071: temperature to substrates at higher temperatures, as indicated by the thermochemistry of the transport reaction. The experimental variables of- the transport process, such as the substrate temperature, the pressure pi the transport agent, and so forth, have been studied. The rate -determining step of the transport process appears to he the ),ale of chemical reaction in the source region. The transported films are similar to thermally grown silica films in physical proper-ties with the exception of 'some what higher dissolrrtion rates. SILICA films deposited on suitable substrates serve many purposes in electronic devices. They are used for the fabrication of tunneling devices, the surface passivation of devices, and the shielding of devices from nuclear radiation: and as selective masks against the diffusion of specific impurities into semiconductors. Doped silica films can also be used as sources for the diffusion of impurities into semiconductors. Several oxidation and deposition techniques for the preparation of silica films have been developed to meet the requirements of these applications. The therma1 oxidation of silicon by oxygen or steam at temperatures above 900 C is commonly used in silicon technology. The deposition techniques are perhaps more advantageous since they usually require lower temperatures and are not limited to silicon substrates. Silica films have been deposited on silicon and other substrates by reactive sputtering and chemical reactions. The sputtering of silicon in an oxygen atmosphere is capable of depositing good-quality silica films on silicon' and gallium arenide. Many chemical reactions are known to yield silica at room temperature or higher. These reactions may involve intermediate steps. However, the final step yielding silica should take place predominately on the substrate surface in order to produce adherent films. When silica is formed in the gas phase by volume reactions, no adherent deposit can be obtained. Generally, the experimental conditions of a reaction can be varied so that the surface reaction predominates over the volume reaction. The chemical reactions which have been used successfully for the deposition of silica films are briefly as follows. The pyrolysis of alkoxysilanes in an inert atmosphere or under reduced pressure has been employed to deposit silica films on germanium3 and silicon4 at 650" to 750°C in a flow system. The deposition of silica films from alkoxysilanes has also been achieved at nearly room temperature by a low-pressure plasma. Device quality silica films have been deposited on germanium and gallium arsenide by the deposition of an amorphous thin silicon film followed by oxidation at 600" to 700" . Silica films for high-temperature capacitors have been produced by the hydrolysis of silicon tetrabromide at 950°C in argon and hydrogen atmospheres.7 We have developed a chemical-transport technique for the deposition of silica films on semiconductor substrates at relatively low temperatures. The thermochemistry of the transport reaction, the experimental variables of the transport process, and the properties of the transported silica films are described in this paper. THERMOCHEMICAL CONSDERATIONS The transport of solid substances by chemical reactions in the presence of a temperature gradient has been used for the preparation of films and crystals of many electronic materials. In this technique, a gaseous reagent is chosen so that it reacts reversibly with the solid substance under consideration to form volatile products. Since the equilibrium constants of most reactions are temperature-dependent, the transport of these products to regions of suitable temperature in the reaction system would cause the reverse reaction to take place. depositing the original solid. When the equilibrium is shifted toward the formation of the solid as the temperature is decreased, the solid is transported from a high-temperature zone to a lower-temperature region, and vice versa. This chemical-transport technique can be carried out in a closed or gas-flow system. In a closed system, chemical equilibrium is presumably established in the different temperature regions of the system, and the transport agent regenerated in the deposition region repeats the transport process in a cyclic manner. The local chemical equilibrium may not be approached in a flow system: however, this system offers a greater degree of flexibility. Silica reacts reversibly with hydrogen fluoride and this reaction was chosen for the transport process. The over-all reaction between silica and hydrogen fluoride may be written as: SiO2(s) + 4HF(g-) = SiF4Ur) + 2H2O(^)

Jan 1, 1965

By J. G. Y. Chow, S. B. McRickard

The tensi1e properties of Ferrovac iron have been studied from 4° to 300°K. The stress required for macroscopic yielding was found to he constant below approximately 50°K. The effect of mechanical twinning on this low -temperature stress plateau was investigated. The onset of twinning occurs in this iron between 130° and 150°K and depending on its previous thermal history the twinning-stress curue may drop below or remain above the vield-stress curves as the temperature is lowered. Twinning has been shown to initiate slip in quenclzed iron at low temperatures. In no instances, however, did the onset of twinning alter the continuity of the yield stress -tempwature curve. Our data shows that carbon inhibits twinning and slip at low tem-peratures. This observation nay be used to explain the ductile-to-brittle transition in iron. The effect of fast neutron irradiation on yielding and embrittlement in iron and Fe-C alloys is offered as supporting evidence for this viewpoint. THE mode of yielding in iron at low temperatures was studied in an attempt to find an expression based on a single mechanism to describe the thermal dependence of the yield stress of iron. There are two types of inflections observed in the variation of the yield stress with temperature in iron and Fe-C alloys. The first is associated with ductile behavior and consists of a region extending 50" to 100°K above absolute zero in which the yield stress is independent of temperature. The second is observed in more brittle materials such as Fe-C alloys and irradiated iron and consists of an abrupt discontinuity in the yield curve as the temperature is lowered through a ductile-to-brittle transition point. The temperature dependence of the yield stress for iron with four grain diameters as found in this study is shown in Fig. 1. To varying degrees all the curves appear to flatten or approach an asymptotic value as the temperature is lowered below 50°K. Several other investigators1,2 have observed a plateau in the yield stress of iron and steel at low temperatures and in 1956 Louat3 presented a theory which contained an explanation for this behavior. In a subsequent exchange with Erickson and Low4'5 who attributed the plateau to the onset of mechanical twinning Louat8 showed that twinning first occurs in iron and steel tested in tension at temperatures as high as 140°K which is well above the observed plateau in yield stress. Furthermore he pointed out that both twinning and slip are basically dislocation processes and that with modified parameters his original theory still applied when deformation is initiated by twinning. Variables which affect the ductile-to-brittle transition in iron are test temperature, strain rate, composition and grain size.7 LOW,8 Hahn et al.,9 and Hull10 have provided evidence which links brittle fracture at a given temperature with the specimen grain size and the onset of twinning. In fact, Hull equates the brittle fracture stress to the twinning stress. On the other hand brittle fracture has been observed in the absence of twinning and priestnerl1 has given a fracture criterion which is valid whether or not fracture is preceded by extensive twinning. The data presented here clarify the role of twinning in the low-temperature deformation of iron. Strong evidence is given that the amount and distribution of interstitial impurities such as carbon are of

Jan 1, 1965

G. R. Compton (Gold Mines of Kalgoorlie (Australia) Ltd., Fimiston, W. A.) : In congratulating Mr. Hooker upon his resume of Mr Parry's paper I have in mind the fact that he carried out the research into pipe pressures. Hydraulic filling as practised in Kalgoorlie has created world wide interest, with these pressures and percolation being vital points.Early in the 1950s, representatives of the Kolar field were conduGted over the local mines where stopes at depths below 2,000 ft were being filled. The problems of pipe pressures were their main consideration since depths of up to 10,000 ft were envisaged.Mr Krishnaiah and Mr Murthy from the same field are with us today and perhaps we may hear of their experiences with depths of 6,000 ft and long lateral lines.J. Holly (Lake View and Star Ltd., Fimiston, W.A.): There is one phase, which I would like to mention myself, that has been very evident in Kalgoorlie operations. That is, we do not get the percolation properties that are obtained on many other fields in the world, and our tendency here has been to assess the quality of our fill more by its settling rate, i.e. the rate at which we can draw off clear water at the surface of the filling levels, rather than the rate that this water percolates down through the fill before it consolidates.We are tending now to measure the quality of our fill as a settling rate rather than as a percolation rate.Americans talk about percolation rates being the important property: If anyone has any experience on operating with fills with different percolation rates, I think their views would be very interesting to the meeting art this stage. Mr ...

Jan 1, 1965

By O. D. Gonzalez, R. A. Oriani

A thermo-osmosis technique has been used to measure the heat of transport, Q* , of hydrogen and of deuterium dissolved in a iron and in nickel, and of hydrogen in Feo.6Nio.4 in the tempevature range 400° to 600°C. For all these systems, Q* is negative and has a large temperature coefficient; an isotope effect can be established for the solutes only in nickel. The magnitude of Q* is considerably larger than the activation energy, E , for migration in the case of these isotopes in a iron, so that all variants of the Wirtz model must be rejected. The phenomenological definition of Q* is developed to show that Q* is related to the mechanisms by which the activation energy is dissipated back into the lattice, and that Q*/E is a function of the ratios of the mean free paths of electrons and of phonons to the distance of jump of the diffusing atom. A correlation is shown to exist between the sign of Q* in thermal diffusion and that of the effective charge in electro migration, and may be understood as due to the large ratio of the mean free path of electrons to that of phonons. THE study of nonisothermal diffusion in the solid state is of interest because certain aspects of the mechanism of diffusion are made manifest which remain concealed though still present in the isothermal case. The thermodynamics of irreversible processes characterizes nonisothermal diffusion, known as thermal diffusion or as the Ludwig-Soret effect, by a quantity, Q*, called the heat of transport, which essentially measures the sign and the magnitude of the steady-state concentration gradient produced by the imposed temperature gradient. The problem then is to understand the quantity Q* at the atomistic level. There does not exist a theory for the atomistic interpretation of the heat of transport. There are, however, two classes of simple models which seem to afford some physical insight into Q*. Wirtz's model1, z and its subsequent generalizations partition the activation energy, E, for the migration of the atom spatially about the region of the migrating atom, so that Q* is the difference between the portion of the activation energy centered about the original site of the jumping atom and that portion about the arrival site. Clearly, the magnitude of Q* cannot on this model be larger than the activation energy for migration. The model of Oriani3 also considers the spatial distribution of E not only before but also after the atomic jump, and Q* is related to the variation of the spatial distribution of E that is produced by the jump. The simplest kind of system with which to compare the consequences of these ideas is the interstitial solid solution, since one may easily choose a temperature at which only the interstitial component moves, the solvent lattice serving as a completely satisfactory frame of reference. Thus, one avoids complications arising when both species in a binary system move. In addition, one avoids the necessity of knowing the energy for the formation of a vacancy, something which is needed for the analysis of thermal-diffusion data on metals which diffuse by the vacancy-exchange mechanism. However, the number of well-measured interstitial systems is extremely small, and, in particular, there are almost no data in the published literature for the temperature dependence of the heat of transport. If one works with solutes which are gases in the pure state at ordinary temperatures, one may use the technique of thermo-osmosis4 which permits thermal diffusion to be measured over a small temperature difference so that the temperature dependence of Q* can be more easily determined. The choice of dissolved hydrogen in iron and nickel was based on these considerations as well as on the desire to look for an isotope effect associated with localized

Jan 1, 1965

By F. C. Appleyard

A couple of miles southwest of the town of Saltville in the western tip of Virginia is a little village called Plasterco. Gypsum has been produced in this area since about the year 1815, being originally found as small outcrops at the surface. Production in the early days was very small, and the use of the mineral was limited to that of "land plaster" or ground gypsum which was spread on the land to sweeten the soil. In the late 1800's, a small calcining plant was constructed and the production of gypsum plaster began. About this same time, the surface rock was depleted and it became necessary to begin underground mining operations in order to maintain a continuous supply of raw material. The United States Gypsum Company became interested in this property in 1909, and has operated there ever since, having enlarged the calcining mill and built a plant for the manufacture of gypsum wall-board in the middle 1920's. Production of gypsum continues from underground' mining operations, and the present mine at Plasterco is now about 1,000 feet below the surface, making it the deepest gypsum mine' in the world.

Jan 1, 1965

Quarrying and crushing 500 tons of limestone plus burning some 240 tons of limestone per day are the two initial phases in the production of borax, soda ash, sodium sulfate and related chemicals at Stauffer Chemical Co.'s plant in Westend, Calif. These processing steps have been upgraded in recent years by the installation of new primary and secondary crushers, an 8 x 340-ft rotary kiln plus kiln feed, control and cooling components-all designed and manufactured by Traylor Engineering and Manufacturing Division of Fuller Co. As a result of this new equipment, a new product- quicklime-has been added to the West End product family and considerable reductions have been realized in fuel and manpower costs.

Jan 1, 1965

By R. J. Pearce, I. Whittle, J. J. Stobbs

The oxidation kinetics of UCu5 in carbon dioxide have been studied over the temperature range 350° to 850°C. At any one temperature, two successive parabolic rate constants are obtained. Up to 650°C, the temperature dependence of the reaction is snzall and the first parabolic rate constant is higher than the second. At temperatures of 690°C and above, there is a very marked temperature dependence and the second rate constant is the higher. Metallo-graphic examination has shown that attack proceeds via internal oxidation. THE oxidation behavior of the U-Cu intermetallic compound, UCu5, in carbon dioxide was briefly examined during investigations aimed at selecting oxidation-resistant uranium-alloy coatings.' It was found that an extremely thick, coherent scale was formed coated at the scale-gas interface with a thin, apparently continuous layer of copper. A more detailed investigation of the oxidation of UCus has now been made. Previous published work2 has been limited to a brief examination of UCu5 in connection with the oxidation of a U-1 wt pct Cu alloy in carbon dioxide. No attempt was made to explain its behavior, but the work indicated that attack proceeded by intern oxidation, with the formation of a layer of copper on the surface of the specimen. EXPERIMENTAL UCus was prepared by arc melting the stoichio-metric amounts of high-purity copper* and uran-

Jan 1, 1965

By T. B. Massalski, Horace Pops

Martensitic transformations were observed by optical metallography and electrical-resistivity measurements during cooling at cryogenic temperatures of the bcc pr-phase Au-Zn alloys. The com-position dependence of the MS, MF, AS , and AF temperatures have been determined. It is concluded that the martensitic platelets which grow mainly in the lengthwise direction and which are associated with a very small temperature hysteresis are "thermoelastic" martensite. In some cases the observed structure seems to have no definite crys-tallographic habit or consists of a mixture of- plates and broad transformed areas. THE majority of the bcc /3-phase alloys in systems of copper, silver, and gold with zinc and cadmium are unstable at low temperatures and undergo a transformation upon further cooling into another structure. A large number of such transformations are martensitic. The composition dependence of the Ms temperatures has been determined and reported for CU-~n,' Ag-Cd,' and AU-C~~ alloys. The 50 at. pct ordered Au-Zn p' alloy has been reported by Jan and pearson4 to transform martensitically at 58°K in connection with their study of the de Haas-van Alphen effect The p' phase in the Au-Zn system has the ordered CsC1-type structure. The phase field is shown in Fig. 1: it has the typical V shape which is characteristic of all copper-, silver-, and gold-based binary /3-phase alloys. There appears to be no a priori reason why the transformation should be limited to the equiatomic composition and the availability of a cryogenic stage for optical metallography5 has permitted studies down to the liquid-helium temperature of a series of alloys in this system. EXPERIMENTAL PROCEDURE Predetermined weights of 99.999 pct pure gold and zinc were melted and cast under a partial atmosphere of helium in sealed quartz capsules. Thorough mixing of the molten metals was achieved by vigorous shaking, followed by a rapid quench into a brine solution. All ingots were homogenized at 640°C for 4 days. The loss in weight was usually less than 0.04 wt pct and was assumed to be due to

Jan 1, 1965

By Paul E. Blackburn, Joan B. Berkowitz-Mattuck, Edward J. Felten

The oxidation behavior of MOSi2 has been studied between 450° and 650°C, the temperature region where "pesling" occurs. Disintegration ("pest-ing") of MoSi2 is shown to occur in the presence of oxygen, but not nitrogen, carbon dioxide, carbon monoxide. or argon. The rate of disintegration is extremely sensitive to oxygen pressure. The crack density of polycrystalline MoSi2 increases ivith lime at temperature. All kinds of cracks are observed: THE excellent oxidation resistance of MoSi, at temperatures of 1000 to 1700°C promises to have important technological benefits. However. the ap- Ihose which are confined within a single grain, those that ci'oss grain boundaries transversely, and those that follow grain boundaries. Laue photographs verify the existence of Iranscryslalline cleavage. Single crystals of MOSi2 do not "pest". Tlrcd solrlbility of oxygen in MoSi2 is extremely low, no lattice changes being observed as a result of exposure of MoSi2 to oxygen in the "pest" temperature range. plicability of MoSi2 is somewhat restricted by the occurrence of a completely destructive oxidation of the intermetallic phase at intermediate temperatures (300" to 6003C). This phenomena was ternled to be the "MoSi2 pest" by Fitzer who first observed it.' Molybdenum disilicide is a metallic material in both physical appearance and electrical properties.

Jan 1, 1965

By Philip G. Burkhalter

Total yield and backscattered electron coefficients were measured in this Bureau of Mines study in an microanalyzer as a function of atomic number and of primary crier: ;y in the 15- to 35-kilovolt range. The electron coefficients were obtained indirectly from measurements of the specimen electron current and the primary beam current collected in a Faraday cage and were measured with a precision better than 0.5 percent. Secondary electron emission was suppressed with opposing potential applied to a screen grid surrounding the specimen. The values of the backscattered electron coefficients agreed with published values within 5 percent.

Jan 1, 1965

By William Klement

KNELLER' has recently reported that extensive metastable solid solutions may be obtained in Cu-Fe alloys by simultaneous vapor deposition. This note reports that solid solutions, apparently single -phase, can be obtained for Cu-Fe alloys containing 0 to 20 and 85 to 100 at. pct Fe by rapid quenching from the melt; the inability to extend the solid solubilities further is related to the liquid miscibility gap, Fig. 1, as for Cu-Co alloys.2'3 Accurate lattice spacings of the copper-rich fcc and iron-rich bcc solid solutions have been obtained. Homogeneous alloys were prepared by casting4'5 and sintering2 from elements of 99.9+ pct purity. The quenching techniques were as before,' except the iron-rich alloys were liberally covered with argon while at elevated temperatures. Flakes about 1 sq mm in area were obtained and investigated with the Debye-Scherrer technique, as previously described.2,4 All X-ray work was done at 25° 2°C using filtered copper and cobalt K radiation. Relative visual intensities of the diffraction lines for the phases in the quenched alloys are shown in Table I. The lattice spacings of the fcc structure for alloys containing up to 80 at. pct Fe are plotted in Fig. 2. The variation of these lattice parameters with composition is in good agreement with the re- of cementite spots usually present (all hkl reflections are allowed) and the ease of confusing them with ferrite or martensite reflections. Copies of the report can be obtained by writing to the Materials Research Department, Rocketdyne. 6633 Canoga Avenue, Canoga Park, Calif., 91304. A copy is also available at the Engineering Societies Library, 2nd floor, 345 East 47th Street, New York, N.Y., 10017. Photocopies, either full-size or microfilm, may be purchased from the Engineering Societies Library. sults6 of Andersen and Kingsbury, Fig. 2, although there is some disagreement in absolute value. This discrepancy may be due to the different temperatures at which the X-ray measurements were carried out and perhaps to the different extrapolation procedures. Also, Andersen and Kingsbury6 state that their lattice spacings were computed relative to the wavelengths given by Siegbahn in 1933; this reference has not been found and it is assumed that the well-known 1931 wavelengths were used, the lattice spacings then being in kx units which are converted into angstroms by the factor 1.00202. There is no support for the contention that solution of iron decreases the lattice parameter of copper, as con-

Jan 1, 1965

By K. A. Johnson, F. H. Ellinger, C. C. Land

The Pu-In phase diagram has been determined by thevmal, filtvation, micrographic, and X-ray diffraction methods. This alloy system is characterized by 1) limited solubility of indium (-2 at. pet) in 6 and e plutonium, 2) one eutectic, and 3) fizte intermediate phases. Of the latter, PuIn and PuIn3 melt con-gruently, and Pu31n, Pu31n5, and the high-temperatuve 7 solid solution are formed peritectically. The n phase decomposes eutectoidally into Pu3In and PuIn at 865°C. Although the 6 phase can readily be retained to room temperature, it is not thermo-dynamically stable below 300°C. The Pu-In system has been investigated at Los Alamos as part of a study of the alloys of plutonium with the group 111-B elements. Constitutional studies of the Pu-A1 and Pu-Ga systems have been reported earlier.'9' To date, published information on the constitution of Pu-In alloys covers only the identification of the intermediate phases Pu3In and PuIn3.3,4 EXPERIMENTAL The alloys were prepared from five different lots of plutonium and three different lots of indium. The principal impurities in the plutonium differed from lot to lot within the following limits (in ppm): iron, 30 to 80; nickel, 30 to 60; aluminum, 15 to 30; silicon, 20 to 145: thorium, 50 to 300; carbon, 75 to 335; and oxygen, 20 to 135. Spectroanalysis of the indium showed that two of the lots were 99.9 wt pct pure, and the third was 99.98 wt pct pure. The alloys, in the form of about 5-g buttons, were prepared by arc melting in conventional equipment. The components for each alloy were weighed to the nearest 0.1 mg. In most instances the weight losses during melting were negligible; therefore confirmatory chemical analyses were usually not made. A few results are given in Table I. Density measurements of the arc-cast buttons were made by the liquid displacement of bromoben-zene. Heat treating was done in muffle furnaces controlled to +2°C. The alloy buttons were wrapped in tantalum foil before being enclosed in evacuated clear silica capsules. As a precaution against breakage, each capsule was in turn placed in a silica tube closed with a refractory wool plug prior to being charged into the furnace. For a moderately fast quench of the alloys, the outer protection tubes containing the capsules were plunged into cold water. Differential thermal analyses (DTA) in racuo were performed at heating and cooling rates of about 1.5°C per min. Tantalum crucibles having inverted thermocouple wells were used for most of the analyses. It was found micrographically, however, that the liquid alloys containing more than about 35 at. pct In reacted with the tantalum, resulting in contamination of the surface of the alloy. A search for a more satisfactory crucible material was not successful: tungsten and yttria behaved comparably to tantalum; thoria, vitrified magnesia, and vitrified alumina severely contaminated the alloys. So as to minimize the contamination by the crucible mater-

Jan 1, 1965

By Gordon H. Geiger, J. Bruce Wagner

Electrical conductavity and therrnoelectvic nzeasuretnents on synthetic hematite slabs with 0.01 to 0.90 at. pet Ti and with 0.30 at. pet Ca were made. Additions of titanium and of calcium both increased the electronic conductivity with titanium yielding greater n-type behavior and calciurn p-type behavior. Reduction studies of hematite to magnetite in CO-CO2 atmospheres between 600° and 900°C initially exhibited linear kinetics. These linear rates were increased by additions of titanium and decreased by calcium. IN recent years many studies have been reported in the literature on the kinetics of the reduction of hematite and magnetite to iron. In addition, Hansen and Josephl and Schenck and Schultz2 have reported studies on the reduction of hematite to magnetite, the first step in total reduction to iron. In order to evaluate the results of the studies of over-all reduction in terms of the actual mechanism of the reaction and to define further the important factors in the rate- controlling mechanism of the magnetic roasting reaction, the following experiments were undertaken. Specimens of undoped hematite and hematite containing titanium or calcium in solution as doping agents were reduced to magnetite in CO-CO2 mixtures. In addition, electrical-conductivity measurements were correlated with the reduction kinetics using concepts of defect solid-state chemistry. EXPERIMENTAL Fisher certified Fe2O3 powder was used to make specimens for both the electrical and kinetic studies (see Table I for analysis). Doping with titanium and calcium was accomplished by adding TiO2 and CaO powders to the Fe2O3 powder. The powders were mixed in a Waring blender for minimum times of 1/2 hr. Satisfactory blending was achieved based on comparison of analyses of individual specimens af- ter reduction. The specimens were formed in a steel die using opposed punches with a rectangular opening 10.0 by 40.0 mm. The Fe2O3-TiO, platelets were pressed cold at 16,000 psi. They were sintered for approximately 16 hr at 1075°C in air, in accordance with information in the literature3, 4 on the time and temperature needed to obtain solution of the titanium in the hematite. The Fe2O3-CaO mixtures were first cold-pressed at 20,000 psi and sintered for 3 hr at 1225°C to insure solution of CaO. This material was then ground to -325 mesh in a 6-in. ball mill and the resulting powder was used to make platelets in the same manner as above. The sintered platelets were usually between 1/16 and 1/8 in. thick. They were ground on a carborundum wheel and polished on 2/0 paper. Typical dimensions of the kinetic-study specimens were 1.6 by 0.8 by 0.05 cm, and a typical weight was 0.3 g. Conductivity and thermoelectric specimens were approximately the same size, but were subjected to further sintering in order to ensure maximum densification. Finally, all specimens were measured to the nearest 0.0005 in. and weighed on a Mettler H-15 balance to the nearest 0.0001 g and the density calculated. The average density of the specimens used for the reduction studies was 4.87 g per cc, or 7.1 pet total porosity. The standard deviation ranged from 0.14 to 0.063 g per cc within a composition group. In the present study, the apparent surface area as measured with a micrometer was taken as the true surface area. The chemical analyses for calcium and for titanium within a group showed maximum variations of 50.04 pet from the average values used in Figs. 9 and 11. In order to suspend the specimen from the balance for the kinetic studies, a hole, 0.03 in. in

Jan 1, 1965

By George W. Leney

The iron ore industry might justifiably claim to have originated the science of geophysical prospecting. Their use of geophysical methods was probably the first application of these scientific techniques to the search for economic materials although the exact origin is undoubtedly lost in the unrecorded observations of. some prospector experimenting with compasses or bits of lodestone. Since 1879 when Thalen published "On the Examination of Iron Ore Deposits by Magnetic Measurements" these methods have been a standard supplement to other prospecting techniques. However, many of the great ore bodies of the Precambrian iron ranges were not particularly suitable for geophysical work. The ores were oxidized and enriched through leaching of silica so that they were nearly non-magnetic and other physical properties which distinguished them from the wall rocks were largely destroyed. With the gradual exhaustion of these high grade direct shipping ores, and ores that could be beneficiated by simple means, the iron ore industry turned initially toward the importation of similar high grade foreign ores. At the same time, new processes for concentrating lower grade materials were being developed and older ones improved upon. These concentrates' when pelletized produced such important savings in blast furnace hot metal costs that they now command a premium in the iron ore market and have weakened the competitive position of the remaining high grade ores. The ore bodies now being sought are usually unoxidized and frequently they are also metamorphosed.

Jan 1, 1965

By N. E. Hanna

The current Bureau of Mines active list of permissible explosives includes 124 brands. Thirteen are gelatinous and the rest are the more commonly used granular ammonium nitrate type. The list of permissible blasting devices comprises five Cardox models.

Jan 1, 1965

By R. Barany

The heats of formation of goethite, ferrous vanadate, and manganese molybdate at 298.15° K were determined by solution calorimetry. For formation from the elements, the heat values were -133.7 ±0.3 kcal/mole for goethite, -453.8 ±0.5 kcal/mole for ferrous vanadate, and -284.8 ±0.2 kcal/mole for manganese molybdate. For formation from the oxides, the heat values were -0.9 ±0.1 kca1/mole for goethite, -19.4 ±0.3 kca1/mole for ferrous vanadate, and -14.6 ±O.l kcal/mole for manganese molybdate.

Jan 1, 1965

By J. W. Spretnak, G. W. Powell, J. H. Bucher

Tlze room-temperature tensile fracture oj smooth, round specitnens of three ultrnhigh- strength steels tempered to a wide range of strength levels was studied by means by light and electron-microscopic examination of the fracture surfaces. The fracture of AISI 4340 and 300 M at all the strength levels studied, and H-11, except after tempering at 1200° and 1300°F, occurs in three stages. The initiation of fracture is internal (except in some lightly tcmpeved specimers in which fracture is initiated at surface flaws), and is nucleated largely by separation at metal-second phase intevjaces. TIze voids grow and, coalesce to form a crack. When the crack has reached a sufficienl size, rapid propngutio~z ensues. Failure in this stage of fracture usually occurs by dimpled rupture of inicroshear stefis. In the case of H-11 tempered in the 1125° to 1300°F range, fracture in the shear steps is predominantly by concentrated deformation without void formation. The termination of fracture is usually occomplished by the formation of a shear lib in which fracture occurs by shear dimpled rupture. In the case of H-11 tempered at 1200° and 1300°F, no shear lip was obserued, and the radial elelments extend to the surface—a true termination slage does not exist. ThE tensile fracture of several metals and alloys has been investigated.2-4 In the case of polycrystal-line materials, cup-cone fracture usually results. The mechanism of cup-cone fracture may be summarized as follows.5 Cavities are formed in the necked region of the specimen. They usually are initiated by inclusions or second-phase particles. The cavities extend outwards by means of internal necking, and a crack lying about perpendicular to the length of the specimen is formed in the necked region. Subsequent crack growth occurs by the spread of bands of concentrated plastic deformation inclined at an angle of 30 to 40 deg to the tensile axis. Cavities are formed in the bands of concentrated deformation. The deformation bands zigzag across the bar with the net result that mac-roscopically the crack extends about perpendicular to the specimen axis. The final separation, or cone formation, appears to occur by continued crack propagation along one of the deformation bands out to the surface of the specimen. The micromechanics of the tensile fracture of ultrahigh-strength steels have not been thoroughly investigated. Larson and carr6,7 studied the tensile-fracture surfaces of AISI 4340 with a low-power microscope and reported that three stages of fracture could be observed in general. A centrally located region characterized by circumferential ridges, an annular region characterized by radial surface striations, and a peripheral shear lip were found. It was first pointed out by 1rwin8 that the central region is very probably one of fracture initiation and slow growth, and that the annular, radially striated region is one of rapid crack growth. Presumably the crack grows slowly, assuming roughly a lenticular shape, until it is large enough for the initiation of rapid propagation. In this investigation, it was attempted to determine the fine-scale aspects of the room-temperature tensile fracture of some ultrahigh-strength steels, and to relate the variation in fracture mode with microstructure. The steels studied were AISI 4340, 300M, and H-11 tempered to a wide range of strength levels. I) EXPERIMENTAL PROCEDURE The compositions of the steels studied are given in Table I. The steel was received in the form of hot-rolled bar stock 5/8 to 1 in. in diameter from which oversized specimens were machined and heat-treated. The heat treatments employed are given in Table 11. Subsequent to heat treatment, the specimens were ground to the final dimensions and stress-relieved by heating for 1 hr at 350°F (with the exception of the as-quenched steel). Standard smooth round specimens of 0.252-in. diameter and 1-in. gage length were tested in a Tinius Olsen Universal Testing Machine using a cross-head speed of 0.025 in. per min. The relatively coarse aspects of the fracture topography were determined by light-microscopic examination of sections through the fracture surface of nickel-plated specimens. A direct carbon-replication technique9 was used in the electron-microscopic study of the fracture surfaces. The replicas were examined in the electron microscope, and stereo pairs of electron micrographs were taken. The stereo pairs were then examined using a Wild ST4 Mirror Stereoscope. Carbide and inclusion particles extracted in the replicas were analyzed by selected-area electron diffraction. II) EXPERIMENTAL RESULTS The mechanical testing data are summarized in Table 111. The values reported are the average of

Jan 1, 1965

By Glenn L. Cook

Correlations between mass spectra and molecular structures of 186 organic sulfur compounds are discussed. The olefinic ions, the alkyl ions, the CnE2n+1 ions, the m/e 61 ions, and the m/e 35 ions in the spectra of thiols are related to molecular structure. In the spectra of sulfides, the olefinic ions, the m/e 61 ions, the m/e 35 ions, the CnH2n+1S+ ions, and the CnH2n+1SH+ ions are correlated with molecular structure. For disu1fides, the correlations relate HSSF+& and RSSH+ ions to molecular structure. Base peaks of alkylthiophenes are correlated to their molecular structures. Some unimolecular reactions of sulfur compounds in the mass spectrometer are considered. A cyclic intermediate is suggested for the reaction which produces m/e 47, CH3S+, and m/e 48, CH4S+, ions in the spectra of sulfides. An expanded ring is suggested as a possible intermediate in the reactions of thiophenes. Heats of formation of sulfur-containing ions and their appearance potentials are presented in tabular form. Ionization potentials for sulfur-containing radicals and molecules are also given. Discussion of the spectra, tabulated in the appendixes, provides an insight into the relationship of the molecular structure of a compound to the mass-to-charge ratios and the intensities of the ions in its mass spectrum. Correlations of the mass spectra with molecular structures are empirically developed by observing regularities in the spectra of the reference compounds. Correlations extend the usefulness of mass spectra because they can be employed to determine the molecular structure of an unknown compound.

Jan 1, 1965

By Jr. Gabler

Methods for the direct spectrochemical determination of impurities at the parts-per-million level in tungsten metal and oxide are presented. Several published procedures were investigated and numerous modifications were made in establishing procedures with improved precision and extended lower levels of determinability. Details of standards preparation are presented, experimental work is described, and three preferred methods are described in detail. A germanium carrier-distillation procedure is applicable to the determination of 13 elements in tungsten powder; a silver chloride carrier-distillation procedure provides for the determination of 24 elements in tungstic oxide, and a sustaining ac arc method is applicable to 26 elements in tungstic oxide. The choice of methods to be used depends upon sample form, elements and concentrations to be determined, and the precision and accuracy required. The investigations reported here were undertaken to develop direct spec-trochemical methods with increased accuracy and precision to determine impurities in high-purity tungsten and tungstic oxide, to define the lower concentration levels of detectability and measurement for the common impurities in tungsten by direct spectrographic means, and to present the details of the developed or modified methods that have proved applicable.

Jan 1, 1965