Search Documents

By A M. Goodwin

Detailed stratigraphic studies in the Birch-Uchi Lakes area have shown that the volcanic components are arranged in superimposed sequences, or cycles. Each cycle displays a progression from predominantly mafic effusives below to predominantly felsic extrusives above. Sedimentary rocks are preferentially associated with the felsic extrusives. Two volcanic cycles are represented. The average stratigraphic thickness of the volcanic rocks present is 31,000 feet. The original volcanic pile was probably in the order of 40,000 feet thick. The present lithologic composition is estimated to be: mafic volcanic rocks, 60 per cent; felsic volcanic rocks, 27 per cent; sedimentary rocks, 10 per cent; and others, 3 per cent. Gold occurrences are preferentially distributed with respect to the volcanic succession. Of fifty recorded occurrences, thirty-nine are located in the upper felsic division of the lower volcanic cycle; forty are associated with closely interbanded daciterhyolite pyroclastic rocks, andesitic lavas and siliceous sediments. The gold-bearing quartz veins either lie at the contacts of enclosing lithologic units or occupy cross-cutting fractures in one or more adjacent units.

Jan 1, 1965

By J. B. Cheatham

An analysis of indexing is given for an idealized plastic rock. Indexing refers to chipping from a bit tooth to a previously formed crater. A method is indicated for computing the dependence of chip size and shape as well as force on the tooth for various tooth shapes as a function of crater configuration and distance to the previous crater. Pressure on the tooth is found to vary with depth of penetration after a critical depth has been reached. Damp sand model experiments indicate that simple solutions using linear and logarithmic spiral slip-line fields for Coulomb plastic materials give reasonable approximations to the failure patterns. Both idealized roller cone bits and fixed blade or drag bits are considered, and methods are presented for approximating the force on the bit and the chip volume when the rock is subjected to sufficiently high pressure to behave plastically. One of the primary objectives of drilling research investigations is to develop theoretical equations which can be used to predict the behavior of rock under drilling loading conditions. Since rocks usually fail in a brittle manner at atmospheric conditions, much current research is directed to studies of the brittle failure of rock under the action of drilling too1s. 1,2 The results of triaxial test on rocks indicate that both rock strength and ductility increase at high confining pressures.3 Recent results from single bit-tooth indentation experiments on dry rocks indicate that the transition from brittle to ductile failure under a bit tooth can occur at pressures sufficiently low to be of interest in oil well drilling.4 Single bit tooth experiments and analyses are not directly applicable to the drilling process since one of the important facets in drilling is the interaction between a bit-tooth and the previously formed crater. This interaction is referred to as indexing.' The purpose of the present paper is to indicate how plasticity theory can be applied to the analysis of indexing for plastic rock. Drag bit or fixed-blade drilling is considered and a discussion is given of the drilling action of an idealized roller cone bit. Results of simple experimental studies using a damp sand model are given as a method of visualizing the failure patterns in rocks under high confining pressures. These results are compared with plasticity theory using simple solutions based on linear and logarithmic spiral slip-lines. Discontinuous stress fields are proposed for drag bit drilling based upon the soil mechanics analysis of Shields. SINGLE BIT TOOTH RESULTS Single bit tooth indentation experiments using dry rocks under pressures from 0 to 5000 psi have indicated a correlation between the shape of a force-displacement curve and the nature of the rock failure beneath the tool.4 Continuous linear curves are in-

Jan 1, 1965

By Lloyd H. Yeager

Good morning gentlemen. I'm very pleased to be a part of this fine program for the Society of Mining Engineers. Gypsum, as many of you know, is one of the most unique minerals on earth. The very excellent presentations which you have just witnessed, revealed the geological aspects of gypsum operations. It is not our purpose this morning to pursue this subject further. Instead, we felt you would be interested in some of the uses of gypsum . . . and what the future holds for gypsum products. To help accomplish this, we're going to first show the Gypsum Association's new film, "Shape Of The Future. ' This short movie traces gypsum f ram mines and quarries to its ultimate destination in homes, schools, offices -- in virtually every type of construction. We think you'll be particularly interested in the description of gypsum's fire resistive nature.

Jan 1, 1965

By G. H. F. Gardner

The velocity and attenuation of elastic waves in sandstones were measured as a function of both pressure and fluid saturation. A large change occurs in these quantities if water is added and the rock is not compressed, but the change is small if the rock is subjected to a large overburden pressure. Measurements were made by vibrating cylindrical samples in both the extensional and torsional modes at frequencies up to 30,000 cycles/sec. Formulas were derived which enable the attenuation of dilatational waves in dry rocks to be deduced from the data. Similar experimental methods were used to investigate the properties of unconsolidated sands. Velocities were found to vary with the 1/4 power of the overburden pressure and attenuations to decrease with the 1/6 power. The effects of grain size, amplitude and fluid saturation were studied. Formulas by which the effects produced by a jacket around the sample may be calculated were derived. The practical application of these results to formation valuation is discussed. INTRODUCTION The attenuation of elastic waves in the earth has been of interest to the seismologist and geophysicist for many years, but only recently to the petroleum engineer. Engineering interest has been brought about by the success of velocity logging devices, for it is possible by modification of these instruments to measure the attenuation of sound waves in addition to their velocity and, hence, deduce the mobility of formation fluids as well as the porosities of the rocks which contain them. The main problem is to decide whether field measurements can be made with sufficient accuracy to be of practical use. This problem can only be solved after we know the magnitude of the attenuations which are typical of the earth at various depths. The logarithmic decrement of a fluid-saturated rock is the sum of a "sloshing" decrement and a "jostling" decrement, the former caused by the mobility of the fluid contained within the rock and the latter by the granular framework of the rock. Sloshing decrements can be calculated' using Biot's theory, but the jostling losses are less well understood. The present paper reports an experimental investigation of jostling losses in consolidated and uncon- solidated sands, particularly with respect to the effect of overburden pressure and fluid saturation. Born' showed that the decrement of a sandstone may increase dramatically when only a few per cent by weight of distilled water is added, and that the additional loss is proportional to the frequency of vibration. His measurements were made with no compressive stress on the framework of the rock. M. Gondouin3 investigated similar phenomena for fluid-saturated plasters but also did not compress the samples. In the present paper it is shown that compression of the framework reduces this effect, so that at depth the jostling decrement of a sandstone may be expected to be almost independent of fluid saturation and frequency. Decrements for many sedimentary rocks have been given by Volarovich,4 but all for the state of zero overburden pressure. Anomalously low velocities have been logged in shallow unconsolidated gas sands. Results of the present investigation confirm that these velocities are not caused by correspondingly high attenuations, because the jostling decrement in a packing of sand grains is small and much less than in a consolidated sandstone at the same depth. Velocities in sands have been measured by Tsareva5 and by Hardin6 as a function of pressure, but the corresponding decrements do not appear to have been measured previously. The widely used "resonant bar method" of measuring velocities and decrements was employed. Comments on variations of this technique have recently been published by McSkimmin.7 The main novelty of the present technique was the application of pressure to the samples. It was found possible to do this by placing the apparatus inside a pressure vessel, provided the conditions leading to large additional losses were avoided. These conditions are discussed below. EXPERIMENTAL TECHNIQUE Cylindrical samples were caused to vibrate in both the extensional and torsional mode of vibration and the amplitude of vibration was measured as a function of frequency in the neighborhood of a resonant frequency. The resonant frequency, fr, is related to the corresponding elastic modulus by the formulas where E and N are Young's modulus and the modulus of rigidity, p is the density of the sample, and A the wavelength of the vibration.

Jan 1, 1965

By P. J. Soltis

Direct as well as indirect evidence of a-phase ordering was found in a "near-a" type titanium alloy, Ti-8Al-1Mo-1V. The annealed alloy showed an anomalous decrease in second-stage creep rate at 950°F (510°C) and 47,500 psi. Anomalous increases were noted in initial yield stress after 500 hr creep exposure and in tensile strength after 1100 hr creep exposure. Debye-Scherrer X-ray diffraction patterns obtained on fine-grained polycrystalline speci-ment showed much line broadening and development of superlattice lines after 500 hr at 510° C. Examination with the light and electron microscopes failed to reveal phase changes in thermally exposed material, but detailed metallography is presented illustrating the plastic and fracture characteristics of the alloy. Electron-metallographic evidence is presented, however, which shows the nature of the nucleation and growth of ordered regions from the disordered a in annealed material. In the original phase diagram of the binary Ti-Al system constructed by Ogden et al.1 aluminum was shown to be soluble in a titanium over a wide temperature range at concentrations up to about 30 pct. Subsequently, a number of papers2-7 have appeared which indicate the existence of either intermetallic compounds and/or ordered phases in the a field up to 25 pct Al. In the most recent of these, Goldak and Gordon paw7 have determined unequivocally the ordered hexagonal D019 structure for Ti3Al in a 25 pct Al alloy. No superlattice lines were observed above 1112°F (600°C). Previously, the embrittle-ment encountered by Crossley and Carew4 in low- temperature heat treatments of binary Ti-Al alloys low in aluminum had been attributed to the appearance of a new phase in light micrographs. In the present work, direct as well as indirect evidence is presented showing the existence of a-phase ordering in what is essentially the binary Ti-8A1 alloy containing small percentages of the ß stabilizers molybdenum and vanadium, i.e., the "near-a" Ti-8Al-1Mo-1V alloy. Although Bohanek and Kessler8 have shown that this alloy has good stability at temperatures up to 1100°F (593°C), the present work shows instability at 950°F (510°C) where long exposure times were used. Light and electron microscopy proved very useful in revealing the mechanical behavior of ordered a and led to the conviction that ordered "near-a" alloys may have remarkably good properties and useful engineering applications.

Jan 1, 1965

By R. P. Smith

The carbon content of a number of alloys ranging (before carburitation) from purified iron to purified cobalt was determined for fixed activities of carbon by equilibration with each of six CO-CO2 atmosphere at 1000°C. At fixed carbon activity, the carbon content decreases continuously with increasing cobalt content. For concentrations of 0 to 50 at. pct Co the results can be expressed by a linear interaction equation of the type In y2 = 7.76n2/(n1+n3)+ 2.30 n3/(n1+n3) where y2 is the activity coefficient of carbon (standard state such that y2— 1 as n2 — 0 in the Fe-C binary) and n1, n2, and n3 are the number of atoms of iron, carbon, and cobalt per unit weight of alloy. The results are also given in terms of the a functions. In the same concentration range, the results are in accord with the regular solution theory of Alcock and Richardson. THE carbon content of Fe-Si, Fe-Mn, and Fe-Ni alloys at fixed activities of carbon has been reported previously.'-, The present work extends R. P. SMITH, Member AIME, is Research Chemist, E. C. Bain Laboratory for Fundamental Research, United States Steel Corp., Research Center, Monroeville, Pa. these measurements to a series of Fe-Co alloys. These alloys, like the Fe-Ni alloys, are fcc ("aus-tenitic") over the entire range of composition at 1000°C. EXPERIMENTAL PROCEDURE The alloys were made from electrolytic cobalt and Plast-Iron in a small vacuum-melting furnace. A small amount of graphite was added to each melt to keep the oxygen content low. The ingots were analyzed for iron and carbon: the amount of cobalt was obtained by difference. Analysis of the top and bottom of the ingots indicated that they were uniform in alloy content. Except for the pure cobalt the ingots were hot-rolled to approximately 0.15 cm thickness, cleaned by sandblasting, then cold-rolled to about 0.045 cm. We were not successful in cold rolling the pure cobalt; therefore it was hot-rolled to the final thickness. The last traces of surface oxide were removed by acid pickel, then the samples were treated in a hydrogen-2 pct water vapor mixture at 1100°C to remove carbon and most of the oxygen. The carburizing procedure was similar to that previously described.1,2,4 The alloys in the form of strips about 1.7 cm wide, 7.5 cm long, and 0.04 cm thick, together with a similar specimen of purified iron, were equilibrated with each of six CO-CO2 mixtures of fixed composition, then quenched in the

Jan 1, 1965

By R. R. Nothdurft

The internal friction of eight single crystals of magnesium with orienta-tion ranging from 10° to 84° was measured at 33.5 kc and 272° C, and the results were interpreted in terms of the pinned-dislocation model proposed by Granato and Lucke. Results show that the strain-amplitude-dependent decrement varies with orientation in a manner predictable by the G-L model. Different values of strain-amplitude-independent decrement were observed at different orientation angles, but correlation with the theory was not conclusive. Problems and steps for further study are discussed.

Jan 1, 1965

By Robert E. Barieau

In the design of plants to separate helium from natural gas, it is necessary to estimate the enthalpies of the various streams at various positions in the process. This Bureau of Mines report surveys the various methods that have been used to determine enthalpies and gives information on the organizations with such capabilities. The minimum information required for developing an enthalpy diagram is presented, and the relative merits of the various methods are discussed. It is concluded that methods that require no mass flow rate or energy measurements are to be preferred.

Jan 1, 1965

By B. W. Naugle

The Bureau of Mines investigated the changes that occur in decomposition products when coal is carbonized in a fluidized bed with steam as the fluidizing medium and the vapors are subsequently cracked without condensation in a fluidized bed of high-temperature coke. The coal used was from the High Splint bed, High Splint mine, Harlan County, Ky. Since this coal is agglomerating, it was blended with char. The integrated unit used in this investigation consisted of a 3-inch-diameter fluidized coal carbonizer, a 3.5-inch-diameter cracker containing a bed of high-temperature coke fluidized by the tar vapors and steam from the carbonizer, and gas-cleaning and product-recovery systems. The carbonizer was operated at 485° C and the cracker at 600°, 700°, and 800° C. The process variables investigated were temperature, residence time, and concentration (pound of tar vapors per pound of steam to the cracker) of tar vapors in the cracker. The total tar yields decreased as the temperature of the cracker increased, and at a constant cracker temperature of 600° C the yield of paraffins, acids, aromatics, and olefins in the distillate increased directly with the tar vapor concentration in the cracker. At 700° and 800° C only the acids and aromatics increased with increased concentration. Bases remained essentially constant regardless of the temperature and concentration. Similar results were obtained when the tar from the carbonizer was condensed prior to feeding to the cracker.

Jan 1, 1965

By Robert E. Ennis

The somewhat misnomered "continuous" face section is in most mines today still far from perfect continuity. Achieving uninterrupted flow of coal from the mining machine to the outside has been a long sought for goal. Clearly, the largest problem to be solved in continuous mining today is one of increasing the cutting time of the miner. Full machine utilization can never be achieved with the new high capacity miners, as long as their performance is tied to that of the shuttle car. Figure No. I illustrates the point at which shuttle car haulage distance determines unit productivity rather than the productive capacity of the miner. Continuous mining is never realized. A recent development has proven, however, that truly continuous mining and haulage is possible. The Bell & Zoller Coal Company working with the Research and Development Department of Hewitt-Robins Inc. developed and perfected a new mining system which offers advantages in terms of increased productivity at reduced mining costs and enhances the safety of personnel at the face. This new system involves the use of two pieces of equipment that form a unbroken link, at all times, between the mining machine and the mine belt haulage system. These pieces are a Mobile Bridge Conveyor, and an extensible panel conveyor. The following areas of discussion will be covered during the review of this development. I. The design and operating features of the new system. 2. Its application in underground mining 3. The performance of the system to date 4. Operation and maintenance cost considerations 5. Safety features of the system

Jan 1, 1965

By G. E. Keller

In connection with the work of Committee D5, Coal and Coke, of the American Society for Testing and Materials in developing new standards and improving old standards, series of tests were made to check the variance of sample preparation and analysis of American coals. Table I in the "Tentative Method of Preparing Coal Samples for Analysis - 02013-62T" is rather complicated, and the tests were designed to develop data for the simplification of this table. An allowance of 20% of the total variance of sampling and analysis for the sample preparation and analysis steps was used. Also, instead of coals being grouped into ash ranges, they were grouped as washed and raw (unwashed) coals. As a result of these tests, a simplified Table I for Tentative Standard 02013 has been proposed. A standard test for laboratories to check their variance of sample preparation and analysis has been developed. Committee D5 on Coal and Coke of the American Society for Testing and Materials has been making a study of all standards applying to coal for the purpose of improving and bringing them up to date and for breaking some of the existing standards covering a number of tests into single standards. As an illustration, sample preparation is now partly covered in ASTM Designation D492-48, Sampling Coals Classified According to Ash Content, and partly in ASTM Designation D271-58, Laboratory Sampling and Analysis of Coal and Coke. The latter contains, in addition to parts of sample preparation, methods for determining Moisture, Ash, Volatile Matter, etc. Although revision of sampling methods and sample preparation methods are now assigned separately, it is possible that they may end up as one standard. One of the first new Tentative Standards developed as the result of these studies was ASTM Designation D2013, Tentative Method of Preparing Coal Samples for Analysis. Although this method is quite an im- provement over that in the old standards and gives very specific instructions, Table I (attached) is quite complicated and rather hard to understand. In order to take advantage of reduced quantities or weights, it is necessary to know the ash content within rather narrow limits before sample preparation and no distinction is made as to whether the coal is cleaned or uncleaned. No limits of accuracy are assigned to the sample preparation and analysis. The total over-all accuracy of sampling, preparation and ash determination as given in D492-48 has been specified for commercial sampling procedure as follows: "This procedure is intended for an accuracy such that if a large number of samples were taken from a single lot of coal, the test results in 95 out of 100 cases would fall within ? 10 per cent of the average ash content of the sample." Although Appendix 11, Method for Determining the Over-All Variance of Reduction and Analysis in the Tentative Methods for Mechanical Sampling of Coal, ASTM Designation D2234-63T, does give a method for determing the over-all accuracy of preparation and analysis expressed as variance and also the F test, it does not permit the determination of the variance at the various stages of reduction or of the ash determination. It was decided in 1961 to ask a number of laboratories to run a series of tests for the purpose of determining the variance at various stages of reduction and analysis with the view of simplifying Table I of the Tentative Standard D2013-62-T. This paper is a record of this series of tests with recommendations which resulted from the tests. At the same time and preceding these tests the International Organization for Standardization under Committee TC/27 WG 7 was studying the same problem. Tomlinson1 of England and Dr. paul2 of West Germany had made studies giving quite a bit of information. Also Schwerd and coryel13 published some information which was the main basis for the Mechanical Division provision in ASTM Tentative Standard D2013-62T, Table I. In checking with the various laboratories which offered to cooperate in these tests, none was found which used mechanical division through the entire preparation procedure. It was then decided to use riffles at all stages with the thought that if riffles gave satisfactory variances, approved mechanical

Jan 1, 1965

By G Anders

The mucking out of sub-level headings by slusher and by Autoloader is described, and the performance and costs of both methods are compared. The introduction of the Autoloader is taken as an example to illustrate the meth-od used at the mine for evaluating the suitability of new equipment. The consecutive steps in the process are covered in detail -from the preliminary cost analysis and the preliminary estimate of savings and advantages, and the review of these data after a field investigation, through the elimination of dubious factors, and detailed time and performance studies at the property, to the final assessment of the new equipment and an evaluation of the initial forecast. The Autoloader in Operation. 1198 Introduction AT Mattagami Lake Mines Ltd., the mine workings are laid out basically on a pattern of 60-ft.-wide stapes alternating with 60-ft.-wide pillars, with stope lengths varying from 80 to 200 ft. and stope tonnages generally between 80,000 and 200,000 tons. Stapes are drilled off from sub-levels at 60-ft. intervals, with the

Jan 1, 1965

By A. Lubinski, J. E. Hansford

Jan 1, 1965

By B. A. Cheadle, C. E. Ells

The ovienlalion of hexagonal a-zirconium crystals in cold-drawn Zircaloy-2 tubes and in both as-extruded and heat-treated Zr-2.5 wt pcl ND tubes has been rrleasured using the inverse Pole - figure technique. Uniaxial tensile tests hare shown the Zil-caloy-2 lubes to hare highly anisotropic delovmation behavior whereas heat-treated Zr-2.5 wt pet Nb tubes are nearly isotropic. The differences in deformation behavior are esbloilred from the observed textures of the tubes and the deformation systems known to oberate in Zircnloy,-3. Tlze vcsults lead to an explanation of the high effective strain observed fov the Zircaloy-2 tubes as colrzpared to heat-treated Zr-2.5 wt pet Nb tubes in restrained end burst tests at 280° to 300°C. THE Zr-2.5 wt pct Nb alloy. when heat-treated by quenching from temperatures slightly below the (a + p)/P phase boundary and subsequently aged at 500°C, has tensile strengths about 50 pct greater than those of 20 pct cold-worked Zircaloy-2.1 There is. therefore, considerable economic incentive to replace Zircaloy-2 with the heat-treated alloy in some in-reactor applications. notably for pressure tubes, where strength is a prime consideration. However, when tubes of Zr-2.5 wt pct Nb fabricated by extrusion and drawing prior to heat treatment were subjected to restrained end-burst tests at 300 °C. the circumferential expansion at failure1 was only 10 pct that of cold-drawn Zircaloy-2 tubes in similar tests,2 Table I. This result was not predicted from uniaxial tensile tests in which the ductilities of the two materials were quite similar.' The detailed requirement for ductility in pressure vessels has not yet been worked out. and comparison of the relative merits of cold-worked Zircaloy-2 and heat-treated Zr-2.5 wt pct Nb is further complicated by the irradiation-induced loss of ductility and hydrogen pickup each will undergo from reactor operation.1,2 Nevertheless. the lower circumferential expansion of the Zr-2.5 wt pct Nb tubes raised serious doubts on the advisability of their use as pressure vessels. For this reason, an investigation to determine the cause for different ductilities of the two types of tubes was initiated. From a study of uniaxial tensile properties and crystallographic orientation it has been found that the fracture ductilities observed in the burst tests can be related directly to the crystallographic ori-

Jan 1, 1965

Oren. F. Bridwell: The President declares there is a quorum. Since the minutes of last year's meeting arc published in the Proceedings, unless there is objection, we will dispense with the reading of the minutes. There being no objection the minutes will he dispensed with. Is there a report from the Treasurer? Raymond Venous, Chairman, Auditing Committee: I'd like to submit the report for the Secretary-Treasurer for the previous year. Following is the financial report of the Treasurer from May 21, 1964 to May 24, 1965. (Report submitted) May we say, "Cussie," you keep a very, very nice set of hooks. Thank you. Oren F. Bridwell: You have heard the report of the condition of our treasury. We are solvent, at any rate. You have also heard the report of the Auditing Committee. If we might have a motion that the report of the auditing committee he accepted. Moved, seconded and carried. We'll have a report of the Resolutions Committee. Max A. Robe, Chairman, Resolutions Committee: Ladies and gentlemen, we have four resolutions, which we trust are going to he in the best interests of the Rocky Mountain Coal Mining Institute and the coal industry in general.

Jan 1, 1965

By E. S. Tankins, G. R. Belton

A simple solution model, based upon the formation of molecular species, is developed for strongly electronegative dilute solutes in liquid binary-metallic solvents. Two approximations are considered for the relative concentrations of the species: the random and the quasi-chemical. Equations are presented for the partial molar free energy, enthalpy, and entropy of mixing of the solute. An experimental study has been made of equilibrium in the reaction H2 6) +0 (dissolved) = H2O(g))for the liquid Cu-Co alloys. The standard free energy of solution of oxygen is presented as a function of composition for the alloys at 1550°C and as a function of temperature for five of the alloys. The experimental results for these alloys and also for Cu-Ni alloys are shown to be in reasonable agreernent with the theory in the random approximation. A knowledge of the thermodynamic behavior of dilute solutes in liquid metals and alloys is of importance in understanding and designing refining and alloy-making processes. Accordingly, several attempts have been made to derive suitable solution models to forecast the effect of a third component on the activity coefficient of such a solute in a metal. Alcock and Richardson' reviewed the literature prior to 1958 and also showed that a regular solution model gave a reasonable description in the case of metallic solutes but failed to account for the behavior of the more electronegative solutes sulfur and oxygen. These same authors2 later modified their model by using the quasi-chemical approximation3 to calculate the average composition of the first coordination shell surrounding each solute atom. This modified model was shown to lead to a better qualitative description of the behavior of the electronegative solutes; however, quantitative agreement with experimental data for oxygen in alloys could only be achieved by assuming a very small coordination number. The authors concluded that the major source of error in the model was the assumption that pairwise interaction energies were independent of composition. Substitutional and interstitial random solution models by Wada and saito4 are essentially similar to the first model except that the required interchange energies were derived from the modified solubility parameter equation of Mott, instead of from experimental binary data. Most recently Hoch5 has presented a statistical model for interstitial solutions and has applied the model to the Fe-C-O system. However, as the various interaction energies needed in the model had to be derived from the ternary data, the model does not promise well as a means of forecasting ternary behavior. Each of the above models carries the assumption that the strongly electronegative solutes have the same configurational environment as metallic solutes; i.e., the solute can be treated as a substitutional or interstitial atom in a quasi-crystalline lattice and is surrounded by a normal coordination shell of solvent atoms. There are, however, a number of facts which suggest that this is unlikely. First, the heats of solution are large, being more typical of molecule formation rather than alloying. For example, the heats of solution of monatomic oxygen and sulfur in liquid iron are -90 kea16,8 and -74 kea1,7, 8 respectively. These are to be compared with maximum heats of solution of metallic solutes in liquid iron of about -13 keal (silicon is an exception with -28.5 kea17). The large depression of the surface tension of liquid iron by trace amounts of the electronegative solutes oxygen, sulfur, and selenium9 suggests, by analogy with aqueous systems, the possible existence of polar molecules in the liquid. The effect of these solutes is at least three orders of magnitude greater than normal metal solutes.10 As has been pointed out by Richardson,11 the electron affinities and ionization potentials of oxygen and sulfur are such that it is likely that they exist in metallic solution as negatively charged ions. If this is so, and it is assumed that electrostatic forces play an important role in determining the configuration, it is unlikely that the stable configuration will be that of an isolated ion surrounded by a symmetrical coordination shell of solvent ions. It is more likely that the energy of the system would be lowered by the formation of solute-solvent screened dipoles. The above arguments suggest the formation of "molecular species" between solute and solvent atoms. The idea of the existence of molecular species in such solutions is not new, however', for Marshall and chipman12 have explained in a semi-quantitative manner the C-O equilibrium in liquid iron by postulating the species CO. Chen and Chip-man13 interpreted their measurements on the Cr-O equilibrium in iron in terms of the species CrO. Zapffe and sims14 have also postulated the existence of such species in liquid-iron alloys.

Jan 1, 1965

By Dennis E. Peterson

Land subsidence had been observed in recent years throughout the Southwest. Particular examples of this phenomenon that have gained wide publicity axe in the Long Beach and Central Valley areas of California and, the Houston area of Texas. Less well known is the fact that the land surface Is subsiding in many parts of Arizona, including the Phoenix area. The causes of this problem vary from place to place, as do also the rates of subsidence. In Houston it has been related to pumping water from artesian aquifers; in Long Beach to the development of oil fields; and in the Central Valley to both the lowering of artesian pressures in deep aquifers and the wetting of poorly consolidated surficial deposits. The mechanism by which subsidence occurs in southern Arizona, even though it can be correlated with the continued lowering of ground water levels, is not as apparent as in these other cases. It is the purpose of this paper to examine both the causes and affects of land subsidence in southern and central Arizona.

Jan 1, 1965

By Donald R. Mason, Daniel F. O’Kane

DIFFERENTIAL thermal analysis measurements have been used to determine the ZnTe-In2Te3 pseudo-binary phase diagram. Since ZnTe and In2Te3 are both semiconductors, any intermediate compounds formed in this system should also be semiconductors according to the rules delineated by Mooser and pearson.1 The compound ZnIn2Te4 was first reported by Hahn et a1.2 and it has subsequently been prepared and characterized electrically by several workers. A brief summary of this work has been presented by Mason and O'Kane3 who also report that the compound appeared to melt peritec-tically. The Zn-Te phase diagram has been investigated by Kulwicki4 who found that ZnTe has a melting point of 1290° + 2°C. The In-Te diagram published in Hansen' contains significant errors, and has been redetermined by Grochowski et al.6 However, both sources agree that the melting point of In2Te3 is 667°C, with the latter authors reporting the previously observed solid-solid transformation occurring at about 550°C. Hahn ef al.2 reported lattice-parameter values for the ZnTe-In2Te3 system. The 67 mole pct ZnTe-33 mole pct In2Te3 composition was the only

Jan 1, 1965

By K. G. Davis, P. Fryzuk

The diffusivity of silver in liquid tin has been determined, using the capillavy-reservoir technique, over the temperature range 250° to 500°C. The new value, D = 2.5 x 10'* exp(-2480/ RT) sq cm per sec, differs from that obtained by other workers in an earlier investigation. The analysis of data from the capillary-reservoir technique is discussed. In a recent investigation of the solidification of dilute alloys, values for the diffusion constant of silver in liquid tin were required in the analysis of the formation of impurity substructures. AS a result, measurements were made of the diffusion constants in the temperature range 250° to 500°C (melting point of tin 232°C), for the alloy concentrations used in the solidification experiments and at higher concentrations, to verify previous determinations.I)2 The capillary-reservoir method was adopted, using experimental procedures similar to those followed by Ma and Swalin,1 with the main exception that radioactive silver was used in the present investigation to facilitate solute-concentration measurements. EXPERIMENTAL PROCEDURE a) 100 ppm Samples. Glass capillary tubes of 2 mm inside diameter and approximately 5 cm- long were sealed at one end, evacuated, and filled with tin of 99.999 pct purity. The region of shrinkage near the mouth was cut off, and the tubes were then placed in a graphite holder and immersed, with the open end up, in an unstirred bath of alloy containing 100 ppm Ag 110, where they remained for periods of up to 30 hr. On removal from the bath they were cooled by an air blower. The bath was kept under a small positive pressure of argon, and the temperature controlled to within +1°C. A 10-hr diffusion period was used in the majority of the tests, scatter on runs of less than 5 hr being rather large. The procedure outlined above was chosen in preference to putting alloy in the capillary and pure tin in the bath, in order to avoid segregation when the tubes filled with alloy were first solidified. To minimize segregation when the diffusion period was complete and the capillaries again solidified, the earlier samples were held in thin-walled silica tubes which could be cooled very rapidly. Later tests were made in precision-bore Pyrex tubes, to eliminate effects caused by variations in the capillary diameter. No consistent differences in diffusivity as measured in the two types of tube were detected. After removal from the glass tubing, the samples were sectioned into 2.5 mm lengths and counted for y activity, using a scintillation counter with fixed geometry. Samples were also drawn directly from the bath and counted, so that values for C/C,, the ratio of the weight of Ag 110 in the sample to that in the bath, could be obtained. b) 5000 ppm Alloy. To check for possible effects of concentration, the silver content of the bath was increased to 5000 ppm. Complete mixing was found to have taken place in the capillary after a 10-hr period at 300°C. It appears that the greater density of the alloy was sufficient for buoyancy forces to cause instability in the alloy-tin interface, leading to rapid convective mixing. For the 5000 ppm alloy, therefore, the bath was of pure tin and the capillary tube was filled with alloy. With this arrangement, values of D consistent with those for the 100 ppm alloy were obtained, Fig. 1. CALCULATIONS OF DIFFUSIVITY The terminology used applies to a capillary of pure tin immersed in a bath of alloy. 1) Error-Function Method. under the present experimental conditions, the rod of liquid tin into which silver is penetrating may be considered semi-infinite. Assuming the concentration at the mouth of the tube to remain constant at Co, the concentration C at distance x from the mouth of the tube at time / is given by3 Plots of the inverse error function of (1 -C/Co) vs .v gave straight lines passing through the origin with slope 1/2-, x being corrected for shrinkage both on solidification and while cooling to the melting point (total correction about 6 pct at 500°C). Values for log D obtained in this manner are shown in Fig. 1. A least-squares fit to the relation D = Do exp(-Q/RT)

Jan 1, 1965

By James F. Neill, O&apos

Brown iron ore resources in Barbour, Butler, Crenshaw, and Pike Counties were investigated in a drilling program and geological study by the Federal Bureau of Mines in cooperation with the Alabama Geological Survey and the University of Alabama. The aggregate footage drilled was 18,010 linear feet. When developed, reserves of 12,664,000 long tons of crude ore were indicated, containing from 26.9 to 29.0 percent iron and 0.2 to 1.6 percent manganese under a maximum overburden of 40 feet. Total inferred crude ore for the four counties was calculated to be 827,700,000 long tons. Beneficiation of samples by simulated log washing and use of a 118-inch screen yielded from 46.8 to 51.7 percent iron and 0.2 to 2.6 percent manganese. Screen-test studies indicated no appreciable interlocking between the iron and manganese minerals and the waste particles of materials retained on a 200-mesh screen. Clay was prominent in micron-size slimes. Silica was deleterious in the minus 20-mesh size. While an indicated 2,198,000 dry long tons of usable iron ore can be recovered, sink-and-float tests show that it may be possible for 4,654,000 dry long tons to be recovered by other than log washing. However, applicable commercial processes have not been demonstrated.

Jan 1, 1965