Search Documents

By C. William Parisi

Since the introduction of mechanical mining, some 35 years ago, a great deal of effort has been expended by the coal industry to solve the coal dust problem. The original concern was the possibility of a dust explosion or the propagation of a gas ignition; however, in recent years it has come to be recognized as a possible 'health hazard as well. In the middle thirties, the Pittsburgh Coal Company began an intensive study of the dust problem to determine the dust levels created by the various cycles of operation in mechanical mining and to make a comparison with those of hand loading operations. Numerous dust samples were collected with a midget impinger and it was found that dust counts varied from 38 to 268 million particles per cubic foot during hand loading and from 96 to 227 million particles per cubic foot during mechanical loading. The study indicated that the source of underground dust in coal mining could be classified as primary or secondary. A primary source is one associated with appreciable degradation of size, that is, where most of the fines capable of becoming air-borne are produced. A secondary source is one in which most of the fines have been produced at some previous operation and are in such condition that they can become air-borne. Cutting, drilling and blasting are the operations which produce the primary dust. Secondary dust is formed by operations which include; loading, transportation and discharge at transfer points. The study showed clearly that the coal cutting operation was responsible for the greatest amount of dust and that the amount of dust produced varied directly with the speed of cutting; type and dullness of cutting bits; and the distance the cuttings had to fall to the floor. The information obtained from the study enabled our company to decide on a course of action and the direction to follow. With the cooperation of mining machine manufacturers, water tanks with a 200 gallon capacity were built into the machine trucks and were provided with a pump driven by a small motor. A length of 1/2" water hose carried the water from the pump to the two water spray nozzles located at the front of the machine. Water was delivered to the machine tanks by water cars which were filled on the surface or from an underground water supply. It was during these early days that wetting agents were introduced into the water system. Our studies revealed that wetting agents did little better than plain water in the abatement of the dust problem. It was found that when using a wetting agent less water was required to obtain the same results but we could not take advantage of this fact because it was almost impossible to keep the smaller nozzles open to reduce the amount of water being used.

Jan 1, 1967

By G. N. Goldberg, Robert A. Rapp

The steady-state kinetics and microstructures of simultaneous internal oxidation and external scale formation were investigated for the oxidation of Cb-Zr and Ch-Zr-Re alloys in pure oxygen at 1000°C. For each binary alloy, a constant rate of scale formation was observed at steady state; the internal oxidatton zone reached a steady-state, time-independent thickness. The dependence of the scaling rate on zirconium content exhibited a maximum at a low zirconium colttent; more concentrated alloys oxidized at a slower rate than pure columbium. This composition dependence of the scaling rate may be partially attributed to the effect of the internal oxidation process as an intenla1 sink for oxygen, with the formation of voluminous, and relatively impermeable ZrO2 precipitates. However, the morphologies of the ZrO2 internal oxide precipitates also affected the scaling rate. The internal oxide precipitates were distributed uniformly in the external scale. The steady-state thicknesses of the internal oxidation zones were not in agreement with those predicted theoretically from an idealized simple model. However, in this particular alloy systen1 the ideal model is not satisfied experitmentally. For ternary Cb- Zr - Re alloys with Nr10e = 0.02 or 0.05, the steady-state thicknesses of the internal oxidation zones were less than those for the corresponding binary Cb-Zr alloys. For ternary alloys with NRe(0) - 0.05, a more adherent and much less porous external scale was formed, and a reduction in the kinetics of scale formation was observed. A number of authors'-7 have reported linear oxidation kinetics for the reaction of pure columbium at 1000°C in air or in oxygen of about 1 atm pressure. A thin and tightly adherent oxide layer is found at the metal/oxide interface beneath a porous external layer of scale. Although the suboxides CbO and CbO2 represent thermodynamically stable phases at 100O°C, generally only Cb2O5* is identified as a reaction product in quenched specimens. Studies at 1000°C at lower oxygen pressures8,10 (Po2 - 10-4 Torr) show that both CbO and CbO2 do form and that CbO2 is a protective oxide. The growth of CbO2 results in parabolic kinetics until Cb2O5 is nucleated and grows. Apparently because of the large volume change associated with its formation, Cb2O5 is porous and does not serve as a diffusion barrier; linear kinetics prevail after the surface is covered with Cb2o5. On the basis of these observations, several authors5,9,10 have suggested that the linear oxidation of pure columbium at 1000°C in air or oxygen of 1 atm is limited by a Loriers-type mechanism,11 whereby the total rate or reaction is controlled by ionic diffusion through a thin layer of CbO2 which is maintained at a constant thickness throughout the linear oxidation. However, the concept of a Loriers model for a three-phase CbOlCbO2 Cb2O5 scale, with the only oxygen activity gradient across the NbO2 phase, is not self-consistent. Further, the suboxides CbO and CbO2 were not observed in the high-temperature X-ray diffraction study of columbium oxidation by Goldschmidt.8 From investigations in which the large PO2, dependence of the linear scaling rate was demonstrated, the importance of an oxygen adsorption or dissolution step has been suggested.4,5,7,10,12 Thus the mechanism for the linear oxidation of pure columbium remains quite controversial. Since further insight into the oxidation mechanism of pure columbium is not provided by this investigation, the authors wish to emphasize at the outset that their experimental results are not interpreted in terms of a particular rate controlling step for the oxidation of pure columbium. Previous investigations13-18 of the oxidation of Cb-Zr solid-solution alloys in air or oxygen at 1000°C suggest a remarkable dependence upon zirconium content. For an alloy of bulk zirconium mole fraction, N2r(0) equal to 0.05 or 0.10, the oxygen uptake is reported to be as high as four times greater than that for pure columbium;13,14 for alloys with NZr(0) 0.05 or 0.10 the oxygen uptake is reported to decrease with increasing NZr(0); to a minimum uptake of about one quarter that for pure columbium at NZr(0): = 0.50.13-15Since zirconium forms a more stable oxide (ZrO2) than the lowest columbium oxide (CbO), and since columbium exhibits a high solubility19,20 and diffusivity21,23 for oxygen, the internal oxidation of the zirconium component to ZrO2 is expected at a reaction front ahead of the advancing metal/scale interface. The external scale is then formed at the metal/scale interface by the inward migration of oxygen through the scale, probably through a series combination of molecular and ionic diffusion. Internal oxidation in conjunction with external scale formation has been investigated by Maak24 for the oxidation of dilute Cu-Be alloys in pure oxygen at 850°C. For cu-Be and many other binary alloys,24-27 very small, essentially uniaxial internal oxide particles are formed in the most dilute compositions; for somewhat more concentrated alloys. the internal oxide particles precipitate as platelets or needles. From pertinent solutions to the diffusion equation, Maak28

Jan 1, 1967

By J. B. Cheatham, C. E. Murphey

Presently, computer control of Borobolic direction cannot be obtained during drilling, and most straight-holc drilling methods attempt to resist hole deviation rather than control direction. Many of the theories advanced as possible explanations of the cause of hole deviation are Summarized berein. A new correlation of physical partables is introduced to indicate bow factors such iis drill collar stiffness clearance and hit weight influence borehole deviation, .A methord is proposed for predicting the rate of change of hole angle when drilling conditions are changed. INTRODUCTION Control of borehole direction during drilling can be difficult and costly. Unintentional crooked holes are often lrilleti in dipping formations and many times directional drilling is required when the surface location is not directly above the target area —- for example, at offshore and mountainous locations. Prilllng progress can be greatly hindered in either air or liquid drilling when it be comes necessary to use low bit weight to prevent excessive hole angle build-up. If hole inclination becomes too great, drill pipe drag becomes excessive and fishing risks are increased, logging is more difficult and problems of differential sticking, key seating and fatigue failures may be encountered. Dog-legs and key seats are more serious problems than steep inclination angles: therefore, reducing rate of direction change is preferred to attempting to maintain absolutely vertical holes. Consequently, a straight inclineti hole is preferable to a nearly vertical crooked hole containing numerous dog-legs. In this paper, theories of the cause of hole deviation and analyses of drill string behavior under down-hole conclitions are summarized. Methods for computing hole deviation are presented und systems for resisting deviation as well as neans for provic!ing control of holt- direction are iliscusseI. A new correlation of physical variables is introduced tu indicate how factors such as drill collar stiffness, clearance and bit weight influence borehole deviation. A method is oroposeti for predicting the rate of change of hole anFrle when drilling conditions are clianged. IIEVIEU' OF PREVIOUS WORK ON HOIaE DEVIATION Significant progress in the theoretical analysis of hole deviation problems has been made in the past 1 5 years. The pioneering work has been primarily a result of the efforts of Lubinski and Woods.l-5 In 1950, Lubinski 1 considered the buckling of a drill string in a straig:rt vertical hole, a problem also considered by Willers6 in 1941. It wns concluded that very low bit weights must be used to prevent hole deviation resulting from drill collar buckling. The use of conventional stabilizers was proposed2 in 1951 by Mac Donald and Lubinski as a method for permitting greater Sit weights to he carried without drill collar buckling. These authors pointed out that a 2° nearly vertical spiral hole can cause severe key seatinp, and drill pine near, wilereas n 3 straight inclined hole with deviation all in one direction, while not vertical, will not result in serious drillirig or producing problems. Studies were continued with an investigation of straight inclined holes by Lubinski and Woods3 in 1953. In this paper they concluded that perfectlv vertical holes cannot be drilled even in isotropic forriations unless extremely low bit P-eights are used. .l'l~ey postulated that constant drilling conditions produce holes of constant inclination angle and varying conditions cause the hole to drill at a neiv equilibrium angle. This analysis was not concerned with drill string buckling since it was based on an equilibrium solution in which the ~irill string Was presumed to lie along the lower side of the hole abcrve the point of tangency. Weight of the drill collars below the point of tangency tends to force the hole toyard the vertical, whereas the weight on hit tends to force the hole aurav from the vertica l. The concept of an anisotropic formation Lvas introduced as an empirical method for explaining actual drilling data and as a means for extrapolating known deviation data to otiier conditions of hit

Jan 1, 1967

By Jr. Hill

Laboratory metallurgical treatments of three high-iron bauxite ores from Arkansas were conducted to determine the relative effectiveness of experimental methods for recovering alumina and a commercially acceptable iron concentrate. The standard for evaluating recoveries from experimental processes was the Al2O3 recovery from Bayer digests of the crude ores; recoveries from digestion of the three ores were 74.1, 87.4, and 88.7 percent. Flotation, magnetic separation, or various combinations of digestion, calcination, and reduction-sintering, leaching, and magnetic separation of leach residues failed to produce Al2O3 recoveries as high as the standard. A high-iron-bearing fraction, containing between 68 and 78 percent of the total iron, was produced in a three-phase treatment involving a caustic, lime reduction-sinter of the crude ore, water extraction of Al2O3 from the sinter, and magnetic separation of the leach residue.

Jan 1, 1967

By J. M. Stuve

Standard heats of formation (AH°p) of YbCl3 (c) and TmCl3 (c) were measured by solution calorimetry. Heat of solution data are given for ytterbium and thulium metals and corresponding anhydrous trichlorides in 4.360 molal hydrochloric acid. The derived standard heats of formation of YbCl3 (c) and TmCl3 (c) were -229,370 ±720 and -235,820 ±400 cal/mole, respectively, at 298.15° K. The resulting heats of formation for YbC13 and TmCl3 are about 1 kcal and 6.3 kcal more negative than previously published values.

Jan 1, 1967

By Heinz W. Sternberg

A method for the electrochemical reduction of the benzene ring was developed and applied to the electrochemical reduction of coal. Successive electrochemical reductions of a vitrain from low-volatile bituminous coal in ethylenediamine saturated with lithium chloride resulted in the addition of 53 hydrogens per 100 carbon atoms. Ultimate analyses and pyridine solubility of the vitrain recovered after each reduction showed that hydrogen added at the beginning has a much greater effect on solubility than hydrogen added at a later stage. Surprisingly, the removal of sulfur from the vitrain takes place only after the more reactive aromatic rings are reduced. Nuclear magnetic resonance analysis and average molecular weight determination of the extracts of the reduced vitrain samples, representing about 18 percent of the vitrain, showed that these fractions had 95 percent of their hydrogen content on saturated carbon atoms and an average molecular weight of 800 to 900. A study of the effect of operating variables on current efficiency showed that current efficiency is highest with aluminum as cathode material and with lithium chloride as electrolyte. A substantial increase in current efficiency of difficulty reducible olefinic double bonds was achieved by adding a proton donor. This result is significant in connection with the electrochemical reduction of coal which proceeds from readily reducible aromatic double bonds to difficultly reducible isolated double bonds. It is proposed that reduction is achieved by electrolytically generated and subsequently solvated electrons and hence does not require prior adsorption of the substrate at the electrode surface. This offers a distinct advantage for electrolytic reduction of sparingly or insoluble substrates such as coal.

Jan 1, 1967

By K. S. Lane

The problem of stability of slopes in reservoirs is one of real interest in civil engineering. The problem is whether the valley walls will remain stable or whether they are likely to slide as conditions are changed by storage of water in the reservoir. If major slides are indicated, as on the walls of relatively steep canyons, one must estimate whether they will be so located and of sufficient size as to interfere with operation of the reservoir-as by blocking the outlets, or by displacing sufficient water to over-top the dam in a huge wave. Some cases involve problems in soil mechanics for slides in earth or weaker rock; other locations need the assistance of rock mechanics for slides in harder rock. While this is not a new problem, attention has recently been focused on its importance by the hugh landslide into the Vaiont reservoir in 1963, which claimed the lives of over 2000 people and forced abandonment of the dam and powerhouse. VAIONT RESERVOIR SLIDE Fig. 1 shows Vaiont Dam in Italy which is a double curvature arch, 875 ft high, located on a tributary of the Piave River, north and west of Venice. When completed in 1960 it was the highest arch dam in the world. In 1960 a sizable landslide (some 700,000 cu yd) occurred on the left abutment a short distance above the dam. Following this, the reservoir was held down for construction of a by-pass tunnel through the right valley wall to insure connection with the upper end of the reservoir in event of further slides. In October 1963 a giant landslide occurred on the left valley wall, over a width of some 14 miles (see Fig. 2). Over 300 million cu yd slid into the reservoir, displacing the water and forming a hige wave 700 ft above the top of the dam as it hit the opposite, or right, wall of the valley. The wave then passed some 500 ft over top of the dam, followed down the tortuous winding canyon and debouched into the

Jan 1, 1967

By J. D. Prater, H. R. Spedden, E. E. Malouf

With the expansion of copper leaching of the various mine wastes at the Kennecott properties, additional copper recovery facilities have been required. A research and development program has been pursued to determine a suitable economic approach to the processing of the additional leach solutions contemplated. lnvestigations on laboratory and pilot plant scales covered electrowinning, solvent extraction, launder and vat type cells, activated launders, precipitation drums, and precipitation cones. This paper contains information on the development and use of a new precipitation-cone-type copper recovery plant, which provides many advantages over older systems. The application of research findings to the old art of leaching copper from copper-bearing mine waste has resulted in a significant contribution of copper to over-all copper production. For example, at the completion of the current expansion program at the Kennecott properties in the United States, copper produced from waste dump leaching will amount to about 25% of the total production. Formerly only 2% was derived from this source. This planned expansion of copper leaching focused attention on the problem of developing more efficient methods for the recovery of copper from greatly increased volumes of copper-bearing solutions.1 The detailed investigations which have been made in laboratory pilot plant and plant tests for the recovery of copper from copper-bearing solutions have included electrowinning, solvent extraction, ion exchange and cementation with iron in launders, precipitation drums, activated launders, and precipitation cones. The results of these investigations have led to the development of a new precipitation cone-type copper recovery system providing many advantages over older methods. ELECTROWINNING OF COPPER FROM COPPER-BEARING SOLUTIONS The direct electrowinning of copper from relatively dilute solutions of copper-bearing mine water, namely solutions containing 10 to 20 lbs of copper per 1000 gal, has always been an attractive possibility.2,3 By this method, high-purity copper powder can be recovered with a power consumption of 3.5 kwh per Ib of copper. However, once the solution strength de-

Jan 1, 1967

By R. A. Deju, R. B. Bhappu

The theory of electrophoresis is briefly outlined and an apparatus which may be used for electrophoretic studies is explained. The results obtained using this apparatus are in agreement with those obtained by other investigators. How to solve some of the complications which occur in the measurement of zero charge and zeta potential is explained. It is believed that the apparatus described in this paper will allow rapid measurements of zeta potential, zero point of charge, electrophoretic mobility and zeta coefficient. For many years the phenomenon of electrophoresis has been studied, and much work has been done in designing an apparatus for better measurements of mobility, zeta potential and zero charge of minerals. Up to the present, most electrophoresis experiments have involved cumbersome equipment and tedious microscopic observation. The modified cell proposed in this paper obviates these drawbacks by using a Rayoscope together with a special system of lenses and filters. It therefore allows a faster and more accurate measurement of zero charge and particle velocity. THEORY Most authors currently regard zeta potential as the potential difference in an otherwise uniform medium between a point some large distance from the surface of the mineral and a point on the plane of shear. Fuerstenau,1 Miaw,2 and Gaudin and sun3 have performed some calculations of zeta potential using Henry's equation.4 Their results show wide discrepancies, probably due to differences in the past histories of the minerals used. The authors have also noticed this difference on determining the zero point of charge of quartz as shown on Table I.

Jan 1, 1967

By J. W. Downey, A. E. Dwight, R. A. Conner

In a previous paper' we have reported the existence of a number of AB2 Laves phases in which A is a member of the scandium group (including the 1an-

Jan 1, 1967

By J. F. Shultz

The Bureau of Mines investigated the hydrogenation of carbon monoxide and carbon dioxide over Raney nickel catalyst and nitrided fused-iron catalyst using both a single-pass and a recycle system. Activation energy over Raney nickel catalyst is 29 to 32 kcal/mole for synthesis from either CO or CO2, Pressure dependence of the gas conversion is to the 0.3 power for synthesis from CO and to the 0.5 power for synthesis from CO2. Nitrided fused-iron catalysts were tested using high recycle rates and 3H2+lCO, 2H2+lCO, and 1H2+lCO feed gas at 21.4 atmospheres absolute pressure. The relative usage of hydrogen (moles H2 consumed per moles Ha+CO consumed) was larger than in corresponding single-pass tests, and the relative usage of hydrogen approached the feed gas ratio monotonically as conversion increased. Activation energy was found to be 12 or 13 kcal/mole fresh feed gases of 3H2+lCO or 2H2+lCO. For single-pass operation the activation energy under the same conditions was 19 to 21 kcal/mole.

Jan 1, 1967

"Far from being eclipsed by petroleum and natural gas, Canadian coal continues to command wide (and apparently growing) interest.Major R & D investigations are currently heavily oriented toward coal beneficiation (e.g., cleaning and utilization of fines) and toward a broad range of studies on metallurgical coals and cokes. However, active work is also being carried out in the areas of coal geology, mining, transportation and combustion; and, in some laboratories, increasing stress has been laid on developing a number of new, essentially non-fuel uses for coal and coal products.This review summarizes the work of Canadian coal research agencies during 1966 and indicates some of the more important advances made by them."

Jan 1, 1967

By N. G. W. Cook

When an excavation is made underground the original rock stresses are removed from the surfaces of the excavation. These surfaces converge to partially close the excavation and the superincumbent rock mass moves down towards the excavation. If the convergence of the surfaces of the excavation were controlled, energy generated by their motion against the controlling forces could be extracted. Since the total forces in the rock mass are not significantly affected by the excavation, stress concentrations arise around the excavation, which compensate exactly for those stresses no longer transmitted through the excavation. These phenomena give rise to two general principles which provide the basis for analyzing the effects of making any underground excavation. The first of these is that the total force resulting from the stresses across any plane in the rock, including any plane through the excavation, must be the same before and after the excavation is made. The second of these is that energy must necessarily be released as a result of making an underground excavation. It is instructive to consider the implications of these two principles for two extreme cases of material behavior between which the actual behavior of rock must lie, namely, the behavior of a fluid and the behavior of an elastic solid. For the purpose of analysis in this paper, an underground excavation is defined as an excavation in which the smaller horizontal dimension of any open void at a particular horizon is less than the depth of that horizon below surface. In the case of a fluid, any unsupported excavation would fill immediately, as a fluid cannot sustain shear stresses. For the same reason, stress concentrations could not arise and the forces across any plane would necessarily be the same before and after excavation. If the filling of the excavation were controlled by forces applied to the surfaces of the excavation, an amount of energy equal to the product of the fluid pressure

Jan 1, 1967

By William C. Hagel

Oxygen-18 exchange between gaseous oxygen, held at a pressure of 125 mm Hg in a PL-IORh chamber, and splzeres of a Fe2O3 containing three or less grains was determined from 9000 to 1250°C. Isotope equilibrum on crystal surfaces appears to be quickly established, and the rate-determining factor is self-difiusion confbvrning to the relation D = 2.04 esp(- 77,900/RT) sq cin sec-'. Changing sphere diameters caused no detectable variation in diffusion coefficients. Oxygen ions diffuse faster than cations at low temperatures, but a crossover may occur at about 1150°C. INVESTIGATIONS by Davies et al.' and Himmel et al2 have suggested that the mechanism of iron oxidation above 600°C involves a predominance of cation migration in the wüstite (FeO) and magnetite (Fe301) layers and oxygen-ion migration in the hematite (a Fe2O3) layer. Evidence for little cation migration during hematite growth consists of: 1) the disappearance of radioactive-silver markers, presumed to vaporize from the oxide-gas interface, and 2) a large discrepancy between parabolic rate constants for magnetite oxidation and those calculated from Lindner's3 data for cation self-diffusion, D:, using Wagner's theory.4 Reversing the calculations gave anticipated self-diffusion coefficients, D:, for oxygen ions of 3.6 x 10-9 sq cm sec-1 at 1100°C and 5.9 x 10-10 sq cm sec-1 at 1000°C. Since then Kingery et a1.5 reported three values for oxygen-ion diffusion in polycrystalline, sintered hematite. These were obtained near 1200°C, at an oxygen pressure of approximately 150 mm Hg, and could be represented by the Arrhenius expression, Dg = 1 x 10 11 exp(-146,000/RT) sq cm sec-1. Extrapolation to temperatures below 1100°C infers that oxygen ions are less mobile than cations. This contradicts the aforementioned oxidation evidence and also coble7s study of the initial sintering of hematite. From the latter, apparent diffusion coefficients for the slowest rate-controlling species could be calculated, and fair agreement was found with an extension of Lindner's data for cation diffusion. Fig. 1 depicts such comparisons graphically. Three points have been included for the determinations of Himmel et al. on cation diffusion in large, natural hematite crystals surrounded by pure oxygen at atmospheric pressure. No dependence on crystal log raphic direction was noted. Since the value of 10-l4 sq cm sec-' at 1000°C actually represents an upper limit, one might interpret that there is a small decrease in D: when single crystals are employed. On the whole, however, cation diffusion appears relatively well-defined,* while the few results tension to lower temperatures. After having gained experience measuring oxygen-ion diffusion in certain glasses7 and in the corundum oxide, a Cr2O3, the purpose of this work was to determine D; values for hematite and thus possibly assist a mechanistic understanding of the kinetics of the oxidation and reduction of solid iron oxides. I) EXPERIMENTAL PROCEDURE A) Material. Hematite powder of moderately high purity was received from the Columbian Carbon Co. An accompanying lot analysis listed 0.03 H2O, 0.008 weight percents, with the remainder Fe2O3. Subsequent treatments were ball milling, drying, prepressing, and hot-pressing for 60 min at 1350°C under 5000 psi. Since graphite dies coated with a slurry of alumina were used for hot-pressing, the surrounding atmosphere at temperature was sufficiently reducing to form some magnetite on the outer surface of each cylinder. After removing any attached alumina, a stabilizing anneal of 50 hr at 1300°C in oxygen was added. The final product was nonmagnetic and exceeded 97 pct of the density (5.24 g cm-3) usually given for FezO3. On polishing cylindrical ends, counts were made of the number of grain boundary intercepts per

Jan 1, 1967

By C. G. Dunn

This note describes a method for revealing micro-structures in tantalum through an {hkl} effect which was found during a study involving amorphous and crystalline tantalum oxides. Three steps are involved. First, an amorphous film of Ta2O5 is formed anodically1 on the surfaces of the tantalum. The amount needed depents on the thickness of the substrate tantalum; 1600Å of oxide, however, is generally satisfactory in the 1/2 -mil (12 µ) to 3-mil thickness range. The film at this point is uniform in color. Second, the anodized specimen is heated to 800°C in. vacuo during a period of a few minutes and held at temperature for 5 min. During such a treatment some oxygen leaves the oxide through dissolution into the substrate tantalum (e.g., at 10-8 Torr oxide films thinner than about 800 completely disappear on 5-mil strip). Considerable crystallization of the amorphous oxide also occurs adjacent to the metal/oxide interface but not throughout the oxide thickness. The thickness of oxide needed as a residue is not too critical; values between 500 and 1000Å (optical estimate') may be most useful. (The presence of a residual oxide layer after the heat treatment usually is not apparent; in fact, in most instances the surfaces have a metallic appearance. This can be the case also for thicker residual films needed in the detection of a crystalline oxide phase by surface X-ray diffraction—e.g., if the initial oxide film is 3000Å thick, enough crystalline oxide is formed for X-ray detection.) The third step eliminates the metallic appearance at the surface and reveals (or produces) a varied colored film of tantalum oxide. Two methods can be used and both will be illustrated. If the specimen is dipped in 48 pct HF for a few seconds, the tantalum is found to be covered with a multicolored oxide. Moreover the colors correlate with the grain structure of the substrate tantalum through an orientation dependence of the type illustrated in Fig. 1, where results of an orientation analysis by the Laue X-ray method have been plotted. Other film conditions would have provided a different set of colors for the same orientations. Any such correlation, however, provides a basis for a qualitative assessment of the distribution of orientations in a large sample. The cold-rolled structure of tantalum foil produced by a recrystallization anneal and a cold-rolling reduction of 95 pct is not easily obtained by usual metal-lographic methods.' The structure, however, is easily revealed by the present technique, Fig. 2. The alternative third step is to reanodize the specimen. The optical nature of the final anodic film depends on the presence of the crystalline oxide phase; color variations indicate optical thickness variations in the film. As the reanodization voltage is increased from zero, straw and light brown colors appear (as usual), followed now by variations in color from grain to grain depending on {hkl} orientation. Suitable end points, which are determined by voltage and time, are easily established. Fig. 3, for example, shows the grain structure developed in 5-mil tantalum strip during a 30-min re-crystallization and grap-growth anneal at 1800°C. An anodic film of 1600Å thickness was added prior to the special 800°C anneal. Reanodization was done at constant current density (near 0.2 ma per sq cm) in an aqueous solution of H3PO4 (0.01 pct) and was terminated after the initial brown colors were replaced by a deep blue at approximately 30 v. Although good grain contrast can be obtained with bright field illumination, even greater contrast for black and white micrographs may be obtained with polarized light, as in Fig. 3.

Jan 1, 1967

By Robert M. Doerr

The purpose of the investigation was to determine the oxidation behavior of selected tungsten-cobalt alloys. Specimens of Wand W-Co containing 0.7, 1.7, 3.4, and 9.7 weight-percent Co were subjected to pure 02 at 1,000° and 1,100° K, and specimens of W-Co containing 29.8 weight-percent Co, at 1,100° K. Reaction kinetics were determined volumetrically. For specimens other than those containing 29.8 percent Co, the reactions proceeded at about a constant rate at either temperature, indicating the formation of a scale of constant protectivity; the reaction rates were essentially independent of the Co concentration. The scales on these alloy specimens consisted principally of WO3 and CoWO4. Specimens of a 29.8 weight-percent Co alloy, consisting primarily of the W6CO7 phase, oxidized with only slight deviations from the parabolic rate law at 1,100° K. The protective scale on these specimens consisted chiefly of Co3O4, CoW04, and W1 8°49; Co3O4 was outermost, and the W18O49 was adjacent to the alloy. The results suggest that the Co-rich outer scale inhibited the inward transport of 0 to an extent sufficient to greatly limit the amount of the nonprotective WO3 formed, so that protective W18O49 formed instead.

Jan 1, 1967

By S. J. Aresco

The Bureau of Mines has been active in promoting the purchase of coal for Government use under specifications that define the requirements in terms of heating value of the coal, expressed in British thermal units, and the composition as shown by proximate analyses. To these, when required, are added the ash-softening temperature, the free-swelling index, and the Hardgrove grindablity index. Under most of these specification contracts the bidders guarantee the quality of the coal, and that guaranteed by the successful bidder becomes the standard of his contract. The deliveries are sampled in accordance with instructions3 issued by the Bureau of Mines; the samples are analyzed in the Bureau laboratory to determine whether the coal is of the quality guaranteed by the contractor; if it is not, a price adjustment is made. Analyses of the delivered coal and tipple samples (samples collected at mine tipples as coal is being loaded into railroad cars or trucks) provide valuable data for use in evaluating future bids. In addition, the continuous of coal as delivered is a check on the practical results obtained in the coal.

Jan 1, 1967

By D. A. Elkins

This report is the second of a series of three that will evaluate, in order, the metallothermic, carbothermic, and electrolytic methods of magnesium production. The historical development of the carbothermic process is outlined. Production costs varying from 38.9 to 21.8 cents per pound of magnesium are estimated for different versions of the process. Additional suggested process modifications are listed. The technical and economic potential of the different versions are compared. Areas deemed most promising for future research on the process are delineated.

Jan 1, 1967

By H. G. Iverson

Solid state reactions of manganese with silica were investigated in high-temperature tests. Reactions of 0.5 to 4.0 moles manganese (Mn) with 1 mole silica (SiO2) at 1,100° C and of 2.0 Mn:SiO2 mole-ratio mixtures at 1,000° to 1,150° C yielded products consisting of a slag phase and a metallic phase. At 1,100° C, the slag phase from reactions of the low Mn:SiO2 mole-ratio mixtures was composed of SiO2 and rhodonite (MnSiO3), and the slag phase from the high Mn:SiO2 mixtures was composed of MnSiOs and tephroite (Mn2SiO4). The metallic phase from the corresponding low Mn:SiO2 mole-ratio reactants consisted of two manganese silicides, Mn5Si3 and Mn3Si; from the high Mn:SiOg mixtures, it was Mn and the manganese silicide (Mn5Si). For the higher mole ratios of MnSiO2 the manganese content in the metallic phase increased, while the manganese and silica contents of the slag phase remained nearly constant. The slags did not contain free or uncombined manganese oxide (MuO). For the 2.5 to 4.0 Mn:SiO2 mole-ratio mixtures reacted at 1,100° C, the maximum quantities of silica reduced and of the manganese in the slag appeared to become asymptotical at about 41 and 48 percent, respectively. A brominating procedure was developed that was highly selective in removing the metallic constituents from the reaction product, leaving the slag phase as residue. X-ray diffraction patterns were obtained on prepared silicides Mn5Si, Mn3Si, and MnSi.

Jan 1, 1967

By R. N. Orava, L. A. Rice

One of the difficulties encountered in the preparation of titanium specimens for transmission electron microscopy is the formation of a surface hydride phase during the thinning operation at ambient temperatures. This necessarily destroys contrast, obscures features of interest, and often leads to misleading results. By cooling the polishing solution to temperatures below 0°C this problem has been overcome in the past.' However, since the cooling procedure is somewhat inconvenient, a technique was developed at this laboratory for thinning titanium at room temperature. The material examined was A-70 grade commercial-purity titanium purchased from the Crucible Steel Co. of America. The mechanical and thermal treatments, described elsewhere,* yielded a recrystallized grain size of 4 to 5 p. A slice, 0.5 mm thick and 1.5 mm wide, was cut from a bulk specimen2 using a diamond cut-off wheel. The sample was then coated with paraffin wax. Two concentric holes, about 0.03 in. in diam, one at each broad face, were scribed through the wax to the surface of the metal. Subsequent polishing for several minutes resulted in a preferentially thinned or "dimpled" region. Thereafter, the wax was removed and the entire specimen polished to the point of breakthrough at the base of the dimple. Polishing was effected chemically in a solution comprised of 30 pct HF and 70 pct HN03 by volume, kept at room temperature (20" to 25OC). The specimens were mounted in a stereo holder and examined at 100 kv in a Philips l00 B Electron Microscope. A micrograph from a foil prepared in this way is shown in Fig. 1. Several points are noteworthy. This electron micrograph shows neither evidence for the formation of a hydride phase due to specimen preparation nor, moreover, any obvious surface contamination in electron-transparent areas of a freshly prepared foil. Localized variations in foil thickness observed in some specimens seem to be a characteristic of this chemical polish but do not seriously detract from foil quality. With care, the lifetime of a good specimen exceeded 2 hr in the beam. On the other hand, the exposure of a sample to air at atmospheric pressure, when still warm from the beam, clearly resulted in the deterioration of a formerly clean area just previously in the field of view. An example in Fig. 2 of a contaminated region reveals features, and "spots", not unlike those observed in much purer material by Yamane and Ueda. Consequently, one can conclude that: 1) titanium can be thinned satisfactorily in a solution at room temperature for transmission electron microscopy; 2) large-scale precipitates, >50A in diam, are absent in commercial-purity, recrystallized, furnace-cooled, A-70 titanium containing about 3800 wt ppm interstitials and the same amount of iron; 3) care must be taken not to attribute surface contaminants to precipitates. The authors are grateful to the Franklin Institute for financial support and permission to publish.

Jan 1, 1967