Search Documents

By W. R. Reed, J. A. Organiscak

Haul trucks have the potential to generate large amounts of respirable dust. This respirable dust has been shown to be a health hazard to personnel, especially if it has a high silica content. Lack of dust sampling data from haul trucks prompted the completion of a study to quantify respirable dust concentrations. These field studies were conducted measuring instantaneous respirable dust at stationary locations from passing haul trucks at a stone quarry and at a coal mine site. Fugitive dust levels from haul trucks were analyzed to characterize dust dispersion. This analysis indicates safe following distances for haul trucks and other heavy equipment to avoid overexposure of respirable dust from the lead haul truck.

By Steve Kral

In recent years, junior mining companies, mostly listed in Canada, have taken a beating in the finance markets. Simply put, potential investors have been leery of sinking millions into exploration and mining projects due to volatile commodities prices and an uncertain regulatory climate in developed and developing countries. The 2014 edition of the Prospectors and Developers Association of Canada (PDAC), however, seemed to be a bit different for some juniors. Equity valuations have improved and metals prices appear to be stabilizing. So, for some of the stronger junior companies, there is some hope. Merger and acquisition (M&A) activity is picking up and, believe it or not, companies are raising some capital. Billed as the largest annual mining meeting in North America, the PDAC conference attracted more than 25,000 mining and exploration professionals from around the world. Organizers were anticipating attendance to break the 30,000 mark. But, given the state of the exploration end of the mining business, 25,000 is still a respectable number. Junior companies that are in the project feasibility stage, or have made promising discoveries that stand a good chance of proceeding to production, are being looked at by potential investors. Those are the survivors of the last three years of dismal M&A activity. On the other side are the juniors that are still around ? and there are plenty of juniors that were at the PDAC last year but have since disappeared ? but have little or no working capital. One analyst calculated that there are about 850 companies with less than $200,000 in working capital and about 600 with negative working capital. This will likely result in fewer junior mining and exploration companies as the year progresses but the ones that remain should be stronger.

By A. L. Hinde, A. A. Bradley, P. J. Lloyd

The results of slow crushing tests in a stiff testing machine for both small and large step reductions of particle size are given. The energy consumption required to produce a given weight of minus 74 um material was determined when both single-crystal quartz and Witwatersrand reef were crushed. For comparison the two materials tested were also comminuted in a ball mill under optimum conditions. There are indications that slow crushing under stiff conditions is the most efficient method of breakage that can be devised. The comparison with ball milling results thus yields a value for the efficiency of ball milling of approximately 80 per cent. These results confirm that the best current estimates of milling efficiency, which are based on the free boundary surface energy of the material being milled, are probably too low by at least one order of magnitude.

By N. Kumar Kittusamy

ALTHOUGH MANYSTUDIES HAVE SHOWN an association between operating heavy construction equipment and symptoms of musculoskeletal disorders (MSDs), little research has been performed that systematically characterizes the exposure of operating engineers to ergonomic hazards. This study evaluated: 1) vibration at the seat/operator interface;2) transmissibility of vibration in the Z-axis; 3) psychophysical ratings of vibration level and vibration discomfort; and 4) postural requirements of the job. Results indicate that the digging operation had higher levels of total weighted acceleration than high- or low-idling conditions. Transmissibility data showed that the seat amplified vibration, particularly in the lower frequencies. Seats demonstrated that they may not be sufficient in protecting operators from long-term effects of vibration exposure. High positive correlation was found among subjective ratings (vibration discomfort and vibration level), but moderate positive correlation was found between subjective ratings and quantitative vibration levels. Postural evaluations revealed that the operators were required to assume awkward postures of the neck, shoulder and trunk while performing their jobs. Work-related injuries and illnesses pose a continuing threat to the health and well-being of American workers. The construction industry has been historically recognized as having higher rates of fatality, injury and illness than other industries (McVittie285+; BLS). In 1994, an estimated 218,800 lost-work-day injuries were reported in the construction industry (BLS). Construction also had the second-highest incidence rate for sprains and strains. Although the industry has made progress since then, injuries and illnesses, including MSDs, continue to because for concern.

By T. W. Beck

The National Institute for Occupational Safety and Health (NIOSH) conducratory and field tests to evaluate the effectiveness of dust collector bags for reducing dust liberation and operator exposure from a roof bolter’s dust collection system. The laboratory tests evaluated the bag’s effectiveness to contain dust and the effect on canister filter loading in both a bag and bagless condition. The dust emissions from the collector’s exhaust were also measured in each condition during laboratory testing and show that nearly 100% of the test dust fed into the collector was captured by the dust bags. Loading and pressure drop on the dust collector’s canister filter is greatly decreased when using the bags, enabling longer periods of drilling without filter removal/cleaning. The field results showed that, even though dust standards were met, respirable dust in exhausted emissions was reduced around the bolter. Laboratory and field results show that benefits from use of the bags are realized in all areas of operator exposure.

By G. C. Broadhead

The lead district of Southeast Missouri covers an area of over 3000 square miles, including Maries County on the west, Jefferson on the east, Franklin on the north, and part of Madison on the south, or parts of ten counties. A general section of the rocks of the southeast part of this region would be about as follows, numbering from the top: 1. Sandstone (the second of Missouri geologists),.... 20 feet. 2. Chert beds—beds of passage below,...... 126 " 3. Magnesian limestone, chert, and quartzite,. .. 100 to 300 " 4. Lower magnesian limestone,......100 to 150 " 5. Gritstone and lingula beds,....... 50 " 6. Ozark marble beds,........5 to 20 " 7. Sandstone and conglomerate,. .. .. 5 to 90 " 8. Porphyry, Archæan 9. Granite, The thickness is approximate, for it is not possible to obtain the correct thickness of the various beds. No. 1 may be seen as detached outliers or loose masses of a hard sandstone or quartzite, and is found on the hilltops in the southern part of Madison County, in like topographical position in Reynolds County and the western part of Washington County. No. 2 consists of alternations of chert, clay, and quartzite. It is the formation which contains most of the limonite deposits of Central and Southern Missouri. In Reynolds County shafts have penetrated it 75 feet. Outcrops there and in Madison would indicate it to be at least 125 feet thick. Fossils obtained in various places prove it clearly to be of the age of the calciferous saudrock of the New York system, and Nos. 1 and 2 may also be referred to the age of the second sandstone of Missouri. No. 3 consists chiefly of thick beds of ash, drab and flesh-colored magnesian limestone, both coarse and fine-grained. These beds, where they occur, in Washington, Jefferson, and the southern part of Madison Counties, contain a good deal of quartz in drusy cavities. In Washington County the limestones are beautifully ramified by a system of connected drusy cavities generally lined with minute quartz crystals arranged in botryoidal and mammillary forms, and called " mineral blossom " by the miners. This is the lead-bearing rock of Washington County, but in the southern part of Madison it does not appear to be galeniferous. It is also undoubtedly the equivalent of

By Steven Putt

Seismic While Drilling (SWD) is a newly developed technology in the mining industry. Improving upon Measurement While Drilling (MWD) systems, SWD measures mechanical properties of the rock at incremental depths down a blast hole at a much higher resolution. SWD is also immune to common failures and inconsistencies of MWD such as operator and drill specific variation. Seismic While Drilling records the velocity and elastic modulus of the rock with centimeter accuracy in real-time. These properties measured while drilling blastholes are then used as a proxy for density which can be used for: • High resolution geologic modeling • 3D ore control • Drill and blast optimization • Drill to mill tracking One of the distinct challenges with SWD systems is the sheer volume of information acquired. With thousands of measurements per blasthole, the data can be overwhelming for even an experienced engineer. To overcome this complex challenge, the latest cloud computing and analytics models have been simplifying and organizing the data. These newer technologies can amplify an engineer’s capability by delivering actionable insights into their drilling and blasting workflows. The paper presents new results from Datacloud during recent Seismic While Drilling trials in iron ore, metallurgical coal, and hard rock mines around the world. The measurements are compared with wireline geophysical logs, core data, drill cuttings, and conventional measurement while drilling (MWD) systems to validate the technology and show how the data can be used.

By A. J. S. Benade, A. J. A. Heyns, N. B. Strydom

The maximum oxygen intakes of samples of about 30 Bantu, weighing less than 50 kg from different tribal groups (Zulu, Xhosa, Sotho and Shangaan) were measured on a treadmill. The mean maximum oxygen intake of the 164 men was 2,12 litresjmin and only 18 men (11 per cent of the sample) had maximum oxygen intakes of 2,5 litres/min or above (the minimum requirement for such tasks as shovelling rocks and tramming it). The samples of the different tribes differ in age, but when the age effect is taken into account then there were no significant differences between tribes in maximum oxygen intakes. An incidental finding was that both age and body weight correlated significantly with the maximum oxygen intakes of these underweight subjects. Not one of the subjects who weighed less than 45 kg or who was older than 40 years had maximum oxygen intakes high enough to permit their being able to do strenuous work underground. It is clear therefore that Bantu who weigh less than 45 kg or are older than 40 years should not be employed on such strenuous tasks as shovelling rock and tramming it.

By Lon D. Santis

This paper presents data and theorem to calculate the risk of experiencing undesirable lightning related events while blasting or while engaged in other lightning sensitive activities. The paper provides an overview of lightning hazards in blasting operations and a brief history of lightning related blasting accidents. Lightning continues to be the primary cause of premature initiations of explosives in mining, on average, over two such incidents are reported to the Mine Safety and Health Administration (MSHA) each year. The energy contained in lightning discharges and how this energy sets off explosives in mining is presented. Three categories of lightning warning methods: public media, lightning detectors, and atmospheric electrostatic field measurement are discussed. The remainder of the paper presents recently acquired data on the spatial characteristics of lightning development. This data is used to estimate the risk assumed by blasters under certain conditions. Risk estimations are made for electric and nonelectric blasting if persons are evacuated when cloud-to-ground (c-g) lightning approaches within a certain distance. For example, about 0.6% of all c-g lightning strikes have no other c-g lightning strikes within 25 miles in the previous 30 minutes. The paper shows that a typical blaster using nonelectric initiation in a high lightning density area with a 100% accurate lightning detector set to alarm at 25 miles would have a lightning caused unplanned detonation every 14,000 years

By Jafar Safarian

Bauxite is the main raw material used for the production of alumina (Al2O3) through the well-known commercial Bayer process. This process has significant challenges such as limitation in using low-grade bauxites as they contain significant amounts of impurities such as Fe, Si, Ti. The Bayer process residue, which is known as red mud, is also a global environmental challenge due to huge amount of this low value residue production. An alternative sustainable process with high potential to solve these problems and produce valuable and consumable by-products is a pyrometallurgical-hydrometallurgical process in which the low-grade bauxite ore is treated through a smelting-reduction process, yielding iron alloys and a calcium-aluminate slag. Alumina is then produced from the slag by hydrometallurgical treatment. In the present work, the reduction of pellets produced from different bauxite ores by hydrogen is studied and it is shown that complete iron oxides reduction is possible. Further smelting and smelting-aluminothermic reduction of the reduced pellets show that iron and silicon ferroalloys can be produced, in addition to a proper slag for alumina extraction.

By C. P. Lawhon, J. P. Simpson, W. M. Evans

Data obtained under controlled test conditions using a microbit drilling machine showed that oil emulsified in water muds may either increase or decrease the drilling rate, depending upon drilling conditions. A low-viscosity oil such as diesel fuel can give drilling rates in limestone almost equal to that of water. Data obtained for water emulsified in oil muds showed little decrease in the drilling rate in water-saturated cores as the water percentage of the mud was increased above the 5- to 10-percent range. Changes in drilling rate were found to be dependent upon the oil or water concentration of the mud and upon the type of formation drilled. Changes in static filtration on paper (API filtrate) did not correlate with filtration while the mud was circulated across rock. INTRODUCTION Oil additions to water muds have been reported to increase drilling rates, provide hole stability and improve filtration control. Eckel' showed that water-base emulsion muds used in the West Texas area increased drilling rate with increasing oil concentration up to 15 percent oil by volume, but drilling rate decreased at a concentration of 20 percent by volume. Based on laboratory tests using water muds to drill shale, Cunningham and Goins' reported that drilling rates increased and tendency for the bit to ballup decreased with the addition of oil. Percentage increase in drilling rate varied with the particular formation. They showed oil additions to improve drilling rates ap proximately 75 percent in Vicksburg shale and as much as 150 percent in Miocene shale. Each investigation showed an optimum oil content for the particular formation. Most data that indicated improved filtration control due to oil additions were based on static API Eltrates through paper rather than dynamic filtration through permeable rocks. Some types of dynamic test give a better representation of filtration down-hole while drilling and might be more likely to show some correlation with drilling rate. Static filtration would be important, of course, in relation to hole stability and formation damage. This laboratory's drilling tests, conducted on water-raturated Berea sandstone, indicated that improvements in drilling rate were not evident with increasing oil concentration in water-base muds. Investigation also showed similarity between oil-emulsion (water-in-oil) muds and water-emulsion (oil-in-water) muds while drilling these formations. In Lueders limestone high concentration of water-in-oil muds and high concentration of oil-in-water muds provided the same relative drilling rates. In Berea sandstone there was a large reduction in relative drilling rate with both the oil and water muds that contained low percentages of emulsified fluid. Dynamic filtration rates of water muds on rock did not always decrease with increasing oil percentages even though the static API filtration rates on paper did decrease. Data observed in laboratory drilling of limestone and sandstone indicate that improvements in field drilling operations when water- or oil-emulsion muds are wed may not be the result of increased drilling rates but of improved hole conditions. In some cases, actual drilling rates might be slower but improved hole conditions will result in less total time on the hole. DEFINITIONS Mud pressure—Pressure of drilling fluid as measured after leaving the drilling chamber. This is considered as the approximate mud pressure just past the bit and at the face of the formation. Terrastatic pressure—Pressure representing weight of overburden. Formation pressure—Pressure of formation fluid as measured at outlet of drilling chamber. This is considered as approximate pressure of fluid in the pores of the formation. Differential pressure—Difference between the mud pressure and formation pressure. Relative drilling rate, percent—Drilling rate with experimental fluid divided by drilling rate with water times 100 equals percent. LABORATORY EQUiPMENT AND TESTING PROCEDURES The drilling equipment has been described in previous publications The microbit drill is a closed system (capacity, approximately 7 gal) that can be pressurized to 15.000 psi and heated to 500F. Main components are a drilling chamber, filter-heater, rotary-drive and variable-speed cir-

By S. Gallagher, C. A. Hamrick, A. G. Mayton, R Sonier, R. L. Unger

Introduction Industrial safety professionals recognize that adequate illumination is essential to a safe and productive work environment. The need for effective, lighting in underground coal mines is even greater.1 Designing appropriate lighting systems for these mines is no easy [ ] task because of the unique environment and work procedures encountered in underground coal-mining operations. Miners must depend totally on artificial lighting systems to see. Moreover, the working face is a low-reflectivity and low-contrast environment and is continually advancing or retreating.2 Laboratory mock-ups have been a major part of the process lighting equipment manufacturers must under- go to design an underground machine-mounted lighting system. The mock-ups often have taken considerable time. Furthermore, modifications to a lighting system (using different luminaires with an existing configuration or changing a luminaire's location, orientation, etc.) could require more time with additional mock-ups and laboratory measurements. Understanding the need to improve this situation, the US Bureau of Mines has developed an alternate method for facilitating lighting system mock-ups. A PC-Program (CAP),* with the latest software technology enables users to design, alter, and evaluate under- ground machine-mounted illumination systems. Lux levels and distance are measured as the luminaire is moved incrementally through angular traverses about horizontal and vertical axes. The measurements and angles subsequently are entered into the model. From this input data, three-dimensional isolux or isofootcandle profiles are constructed for luminaires that can be placed at various locations and orientations on a mining machine. As an example, Figure 1 shows a computer display of 21.5 Ix or 2.00 fc profiles for luminaires mounted on a simulated mine-shuttle car. Using this information, the model allows the user to determine the lux level at different locations in space about the shuttle car. How the model calculates illumination During initial development of the CAP model, the isolux profile of the luminaire was determined using the inverse square law (ISL) .3 The method of gathering data comprised recording a single measurement of distance at 21.5 ± 1.21x (2.00 ±11 fc) for angular traverses following 0.09 rad (5 degree) increments. This data was then used to find the illumination in space for any other distance at a given azimuth and elevation using the ISL. Limitations, however, exist with this method.4 The main one is that the ISL assumes a luminaire is a single point source of light, so long as the distance is greater than five times the 1al;gest dimension of the luminous area of the luminaire.5 Also, by using a single measurement to calculate the illumination for a given luminaire in the CAP model a large error could result from an inaccurate measurement.

By E. William Rossi, Sean Gallagher, Richard L. Unger

The purpose of this study was to examine the lifting capacity of low-seam coal miners in four restricted work postures (roof heights of 36", 40", 44", and 48"), investigate the associated metabolic costs, and to examine electromyographic (EMG) data from eight trunk muscles during the lifting procedure. Subjects were thirteen underground miners accustomed to handling materials in restricted work postures. Each subject performed two twenty-minute periods of asymnetric lifting in each of four postures during the day of testing. The. frequency of lifting was 10 lifts per minute. A specially designed lifting box incorporated microswitches in one handle of the box and another in the bottom of the box, in order to examine the trunk muscle function at specific points during the lfting cycle. The data collected will be used by the Bureau of Mines to make recommendations for lifting materials in low-seam coal mines.

By R. P. Rothwell

A Reference to the geological map of Alabama shows the Goalmeasures of that State to form three distinct fields. The Coosu, or most easterly, contains about one hundred square miles ; the Cahaba, or middle field, which is also the most southern true coal in the United States, contains about 230 square miles ; and the Warrior field, which contains in the State of Alabama some 5000 square miles, is the southern extremity of the great carboniferous deposit, which extends through Pennsylvania, West Virginia, Kentucky, Tennessee, and Georgia. But very little has yet been done towards developing those coalfields, partly owing to the absence of all commercial manufacturing enterprise in the South under slavery, and partly owing to the want of capital and the disturbed condition of the South since the war. During the past three or four years I have devoted a large part of my time to the examination of the coal and iron ores of this range,

By D. Donald Downey

Pilot Testing Ion Exchange Resin (IEX) can go from very simple beaker testing to complicated column testing. Space velocities, regenerant quantities, loading capacities, ion leakage, are all terms that get accumulated together to prove or disprove a resin’s (or resins’) ability to load a single ion (or specific set of ions). Not getting all the resin’s operating parameters correct will disqualify (or at least skew) the results. Laboratory tests for capacity, moisture content, bead size, metals fouling, etc.—what does it all mean? At last count, there were over twenty-five separate ion exchange resin tests (analyses) that were available to end users. Standard testing procedures identify the resin properties but more specific procedures can be used to identify problems with equipment operation. Then, there are the costs to consider; simple cation resin testing (moisture content, total capacity and bead integrity) is in the $200/sample range. However, add to this Chatillon, Russian Ball Mill Test, HIAC particle size, metals and % regeneration test procedures and the lab work can increase to over $1000/sample. In this paper, the author will explain the “must-do” pilot and test procedures and why they are important and the key to understanding how resin performs ion exchange.

White Cliffs Opal Field is situated in the Parish of Kirk, County of YulguIgra, New South Wales, about sixty miles from Wilcannia, and the River Darling. It is near the southern edge of the cretaceous basin of the interior of Queensland, New South Wales, and South Australia. Twelve miles south-west of the field, at Tarella station, a well sunk at the homestead reached silurian slates at about 127 feet, getting no water but about three miles north-west from the originally discovered and no central portion of the field, a well was sunk by the Momba, Pastoral cmpany, to a depth of 270 feet all the way through the cretaceous beds. At 250 feet a small supply of water was struck, but so much mineralised as to be quite useless. The temperature also was so high that a man could not keep his hand in it and Mr. Hogarth, the Momba Pastoral Company's manager, informs me that so corrosive was the action of the water, that a shovel left down the well for a fortnight, at the time of sinking, was completely eaten away.The well having now fallen in, I have been unable to obtain any of the water for analysis.The western termination of this portion of the cretaceous basin is situated about twenty miles from the present opal field, at which distance the slates, with (probably) devonian sandstones and quartzites resting unconformably thereon, commence to appear. The opal bearing country, as far as at present known, follows a more or less well defined line running north and south towards the northern end of the field, and north-east and south-west towards the southern extremity.

By Richard A. Thomas, Charles D. Litton, Kenneth E. Mura, Harry C. Verakis

Experiments were undertaken to evaluate the flammability of typical noise abatement materials used to line the cab interior of mobile mining equipment. The experiments were conducted using three different experimental configurations: 1. A ventilated tunnel test. 2. A full-size cab test where the interior surfaces were lined with the sample material and then ignited near the floor using a methane-air burner. 3. Standard ASTM E-162 tests using a radiant panel test apparatus. This paper describes the tests and presents the results obtained for 15 to 20 different materials of various chemical compositions and thickness. With one exception, materials that did not exhibit flame spread in the tunnel test also performed well in the full-scale cab test. All materials that had passed only a small-scale flammability test, such as SAE J369, failed dramatically in all three of the above test configurations. With one exception, all materials that performed well in the full-scale cab test had flame spread indices < 25, based upon the ASTM E-162 results. The lone exception had an ASTM E-162 flame spread index of 68. With regard to samples that failed the full-scale cab test, the carbon monoxide levels within the cab reached lethal concentrations in the range of 1.8% to 3.8% within 2 minutes from ignition of the sample—dramatically illustrating the severe fire environment that can result within the cab space.

By Jason Rock, Rob Thompson, Lee Julian

Reactive ground is ground that undergoes a spontaneous exothermic reaction after it comes into contact with nitrates. This is commonly caused by inert rock hosting sulphide minerals, such as pyrites that act as the reagent. The presence and subsequent rate of reaction with nitrate based bulk explosives can be difficult to predict. Once identified, only explosives that are tested and proven to be compatible with the reactive ground may only be used. These typically take the form of inhibited ammonium nitrate emulsion blended with a limited volume of ANFO or porous prilled ammonium nitrate (PPAN) to ensure that all AN prills in the blend are wholly encapsulated and thus protected from the reactive ground. The requirement for high emulsion content bulk products limits the suite of products available for use to high energy, and high expense products. Further, if chemically sensitised products are used, charged holes must be left unstemmed to allow for gassing to occur, adding delay and exposing the blast crew to an unconfined charge in reactive ground. A range of inhibited products has been developed that are solid sensitised and can be bulked to as low as 0.9 g/cc (56.2 lb/ft3). The use of a solid sensitiser enables stemming to occur immediately after each hole is charged, confining any unplanned detonation more safely within the rock mass. The effective and precise manufacture of bulked inhibited products required a new and innovative Mobile Processing Unit (MPU) design. This MPU required the ability to blend two solid raw materials (AN prill & sensitiser) along with two liquid ingredients (AN emulsion and process fuel). This MPU has been designed, manufactured and has used successfully to manufacture low density inhibited explosives. This paper presents an innovative shift in inhibited bulk products with specific reference to their manufacture and application.

By O. Norman Lotter

There are many scales of innovation in the pursuit of concentrator performance improvement, including paradigm change, inventive change and incremental change. All are important, but the last is low risk, low cost and has a relatively high probability of success, given the right metallurgical skills. Seeking continuous improvement is also essential to ensure that performance does not decline over time due to ore type changes, personnel changes, equipment wear and other factors. When properly implemented, these small gains offer a very high rate of return for the project cost because they are made from marginal, not total, operating costs of the plant. To be effective this approach requires plant trials that use designed structure and appropriate statistics to test the observed differences arising from the old and new process treatments, be they a change in flotation reagent, in grind, pulp density, etc. However the pursuit of small but financially significant performance gains is often regarded as fruitless because of the range of variance in plant data, and the consequent difficulty of ‘proving’ that a benefit has been achieved. Opportunity for improvement is thus sometimes relegated to the realm of the impossible, or at best, treated with skepticism. Operations managers prefer to look for the larger gains, which are easier to demonstrate and prove. Unfortunately, these are seldom to be found; rather, a large gain can be more easily made by executing a series of small recovery improvements that are together equivalent to the ephemeral single large gain. In this paper we advocate a policy of continuing improvement driven by rigorous performance testing protocols and a formal ‘risk analysis’ approach to judging the efficacy of changes implemented in the plant. Following these simple procedures allows rational decisions to be made on the basis of quantifying risk and reward. In particular we consider the choice of hurdle rate for decision-making which best balances risk and reward. It is shown through case studies from actual industrial practice that this approach is practical and delivers significant financial value to the operation.

By Sung Tae Kim

The viscosity is one of the most critical properties of slags and thus its influence on the physicochemical phenomena in metallurgical processes has been issued for last decades. The viscosity of ferrous- and non-ferrous metallurgical slags can be understood via structural investigation with spectroscopic methodologies including x-ray photoelectron spectroscopy, infrared- and Raman spectroscopy, and solid state nuclear magnetic resonance spectroscopy, etc. Therefore, the reaction kinetics such as desulfurization in ladle metallurgical furnace, reduction of FeO and MnO in electric arc furnace is strongly dependent on the viscosity of the slags. The rates of oxide (inclusion and refractory) dissolution into the slags and fluxes are governed by the viscosity. Alternatively, the structure of aluminosilicate melts also affects the thermochemical properties such as sulfide capacity, etc. These diverse applications of the viscosity-structure relationship to ferrous- and non-ferrous metallurgical processes were reviewed.