Search Documents

By J. P. Rider

Operating practices and resulting production from longwall faces are continually improving. Consequently, longwall operators are continually seeking to improve the dust control capabilities on longwalls. The National Institute for Occupational Safety and Health (NIOSH) has been conducting dust surveys at longwalls throughout the country in an effort to document the types of controls that are being used and to quantify the relative effectiveness of these controls. To date, surveys have been completed at longwalls in Alabama, Colorado, Pennsylvania, Utah, and West Virginia. In addition NIOSH has been reviewing longwall dust parameters provided by mine operators to MSHA to assess the status of dust control technology being used throughout the industry. Results from the underground dust surveys and information obtained from MSHA will be summarized in this paper to provide an update on longwall dust control technology and practices.

Although these subterranean cavities are common to the Broken Hill big lode, yet the Broken Hill Proprietary is the most prolific in their occurrence, loud they have been found of various dimensions almost from the surface down to the lowest levels yet attained in that mine. Many of these vugbs have contined valuable silver, copper and lead deposits, and some have been remarkable for the beautiful forms of crystallization pendant from the roofs and walls, and collected on the floors. The question arises, How are these caverns and fissures in the ore body formed? There are numerous theories more or less feasible, but that the causes are variant is demonstrated beyond doubt. That water in its passage leaving channels, is one ofthe chief factors for their production is assured, and their presence is likewise due to the shrinkage and dropping of the earth from varions causes, to the deposition of material forming ledges overhanging, and thus leaving spaces below, and also to chemical erosion and electrical action both of which latter are constantly at work in reconstructing, segregating and dissolving tlie mineral and metallic constituents of all ore bodies.One of the most remarkable vughs yet discovered in the big mine was that opened up about three months bitek in the' heart of the ironstone body on Block 11, and located about 40 feet below the 100 feet level of Weatherley's stopes, but now destroyed in the progress of work. Probably it was caused by chemical action, the eating out, so to speak, of a soft and soluble portion of the manganic iron, leaving a,hollow about 15 feet long, with a width and height, of say, 6 feet, carpeted with beautiful zinc with a modicum of limeincrustations, apparently produced by the percolation from around the carbonate waters holding these minerals in solution. This cavern was divided into, what might be termed, a double chamber, by big boulders of manganic iron, also coated with an aggregation of small crystals of zinc and lime although the actual proportion of the latter was not determined.

By Howard E. Parkinson

An environment monitoring and communication system has been installed in the Bruceton Mine, and research is under way to improve mine safety. Standard day-to-day mine communications are available, along with additional systems installed to permit experimentation with wireless radio, through-the-earth phones, along-the-roof paging, and mine face machinery communications. Research is continuing and the essential concepts for a dependable whole mine communication system, providing simple environment monitoring, improved day-to-day communications and post-disaster communications, will be demonstrated in a larger mine with about 900 feet of overburden.

By Barbara Fotta, Lynn Rethi

Within the Mine Safety and Health Administration's (MSHA's) classification of metallnonmetal (MAM) mining, the number of independent contractor' employees has increased significantly in recent years. In 1985 independent contractor employee hours reported to MSHA accounted for 4.5% of all M/NM mining employee hours (excluding office workers); by 1994 that proportion had doubled to 9.0%. As a result, these workers now account for an increasingly significant proportion of fatal and nonfatal mining accidents. According to MSHA's statistics, annually computed fatality incidence rates (the number of fatalities per 200,000 employee hours) for independent contractors working in M/NM mining are consistently higher than those for operator employees. Over the five-year period from 1990 through 1994, 53 independent contractor employees were fatally injured while working on M/NM mine property (See Table 1). More than one third of these fatalities (36%) were due to accidents involving powered haulage; 21% were machinery accidents; and 11% percent were falling material accidents. Combined, these three accident classifications accounted for 68% of all independent contractor fatalities occurring on M/NM mine property during these years. Clearly, current efforts to increase the safety of the mining workforce must also address the safety of the independent contractor employee. This report is a preliminary attempt to identify trends in the employment and safety of independent contractor workers by identifying which segments of M/NM mining are experiencing the greatest increases in the number of independent contractor employees and by examining changes in the rates and types of accidents in which these employees are involved. The employment and accident data used in this report were obtained from the MSHA database. [ ]

By J. G. Ferguson, R. E. Burnton

The nature of the coal and of the roof in No. 3 seam at Coal brook Collieries is such as to preclude the use, during bord and pillar mining, of conventional mining equipment that employs cutting and blasting in its production cycle. Continuous mining machines of the borer type, operating within a mining height range of 1,9-2,3 m, have been successfully employed in No. 3 seam since 1957.The experience gained with this type of equipment, the operational methods adopted, and the results achieved are described. The ventilation method used to eliminate the dust and methane hazards created by this type of equipment is stressed. The limitation on the minimum mining height that can be obtained with the borers in use has lead to the recent introduction of a Rotary Drum type of continuous mining machine. This equipment is capable of operating in areas where the seam width decreases to 1,5m. The production potential of the machine has been proved. The roof conditions created by the cutting action of the Rotary Drum type of miner are not considered satisfactory and a modified drum head profile is to be tried.

By Stephen C. Tadolini, Raymond A. Mazzoni

The International Ground Control Conference in Mining has always provided an open forum for the publication, presentation, discussion, and often heated debate on roof bolting systems mostly with attention to how, when, and why they work. During the last 24 Conferences at least 170 papers have been presented by International Experts on these “simple” devices that range in length from 30-inches to 20 ft and from 5/8 to 2 inches in diameter. Roof bolts are primarily mechanically anchored, glued, cemented, or driven. Bolts are placed vertically, angled, or tied together with special fixtures (trusses and slings). They have been termed active, passive, stick-slip, and several other descriptive acronyms or mining slang expressions. This retrospective paper will present the changes in bolt types and usage, point out some of the biggest myths and hail the most significant advances (according to the authors’ opinions of course).

Interpretation of Leached Outcrops, by Roland Blanchard. Published by Nevada Bureau of Mines, University of Nevada, Reno, Nevada, 89507, 1968, 188 pages. Price $7.50 (R5.40). This book contains a summary of the author's knowledge of leached outcrops, derived from some 30 years' experience as a geologist operating mainly in the United States of America and Australia. Part 1 of the book provides a comprehensive coverage of the various processes and substances involved in the oxidation of many minerals, under different climatic conditions, to form the final leached products. In Part 2, details are given of the appearance and composition of the oxidation products of the following minerals: pyrite, pyrrhotite, arsenopyrite, cha1copyrite, cha1cocite, bornite, tetrahedrite, oxidized copper minerals, galena, cerussite, sphalerite, molybdenite, chromite, hematite, magnetite, manganite, pyrolusite, calcite, siderite, fluorite, salite and supergene silica. The illustrations, the black and white photographs and the colour plates of oxidation products are of a high standard. The material is presented in a logical order and in terms which are not over-technical; hence it is useful to persons other than trained geologists. Despite the advances in geophysical and geochemical prospecting, the location and interpretation of gossans remains an important method of discovering ore bodies, particularly so since the correct interpretation of a leached material can prevent the fruitless and expensive prospecting of an underlying body of uneconomic concentration. Therefore it is considered that this volume will be a valuable addition to the libraries of universities, exploration companies and geologists. It is of interest to note that the author, who died in 1966, presented a paper, under the same title as this book, to the Chemical, Metallurgical and Mining Society of South Africa in 1939. For this work he was awarded the Society's Gold Medal. W.T.S.

By R. K. Sinha, B. S. Choudhary, Desh Deepak, A. K. Mishra, Hemant Agrawal, Shankar Kumar

There are several methods (empirical, statistical, and machine learning tools) to calculate blast-induced ground vibration. Still, due to complications in the blasting procedure, under varying blasting loads and strata conditions, it is not easy to predict and simulate blast vibration precisely. Therefore, a study was conducted to simulate the field blast data in Ansys software using explicit dynamics. For this study, monitoring of ground vibration for 20 single hole blasts was carried out. The density of emulsion explosives was in the range of 0.9 to 1.15 g/cc. In the laboratory, rock properties were determined from the rock sample collected from the mine site before blasting. The in-hole velocity of detonation (VoD) and the density of the emulsion explosive were also determined. These parameters were used for numerical analysis to know the ground vibrations at specified points. The results of ground vibration predicted by the model are validated using field data.

By V. Carlson, J. A. Rowe, E. O. Bennett

This report concerns the microbial flora found throughout the surface facilities of six water-injection systems in Texas and Oklahoma. Each system is described in detail and water quality data are presented when available. Pseudomonads and sulfate-reducers (Desulfovibrio) were the predominate organisms found in the systems. The genera Sphaerotilus, Bacillus, Achromobacter, Minococcus, Clostridium, Flavobacteriurn, and Sarcina were also isolated in significant numbers. Molds, iron bacteria, sulfur bacteria and soil bacteria were found less frequently in the systems. It is concluded that a complex microbiological flora exists in oilfield water-injection systems. A tendency for waters to deteriorate in passage through solid bed filters is also noted. INTRODUCTION The injection of water into a subsurface formation is often accompanied by numerous problems, the origin and nature of which are only partially understood. During the past few years, investigators have indicated that bacteria are involved in some of these problems even though very little specific information is available concerning this matter. It is surprising that investigators working on microbiological problems in water injection have never made a complete study of the flora of these systems. The logical course to pursue is that of identifying the microbial flora and then examining each organism individually and in combination with others to determine if they produce a particular problem. The objective of the present investigation is to identify the microbial flora in water-injection systems. In addition. the quality of the water in most of the systems was determined and some observations made on the extent to which passage through surface-handling facilities affects water quality. The information derived from this study can serve as a foundation for additional basic investigations. EXPERIMENTAL PROCEDURE The microbial flora of six water-injection systems were studied at 50 sampling points. These systems are experiencing problems which may be attributable to micro-organisms, and two were being treated with antimicrobial agents at the time of this study. The samples were obtained by inoculating 1.0 ml of the water onto the different media at the sampling point. The media used for primary isolation included nutrient agar, Strokes agar, M-10-E medium and semi-solid thioglycollate medium. The cultures were returned to the laboratory, incubated at 30°C until growth occured; then, pure cultures were obtained from individual colonies. The pure cultures were identified according to standardbacteriologica1 procedures. Those organisms not fitting identification criteria exactly, even though exhibiting close similarities to known species, are listed as unidentified organisms. Membrane filters were used to make water-quality tests at intervals before and after collection of the microbiological samples. The filter discs were 47 mm in diameter with a 0.45-micron particle-size retention, and the tests were done under closed conditions at 20) psi. Membrane flow rates are plotted as increasing filtrate volumes, and the total solids contents arcs given when available. An effort was made to sample at each place in a system where a change in environment occurred. In this manner, the effect of passage through filters, tanks, hay sections, etc., on the microbial flora and water quality could be observed. RESULTS SYSTEM A This waterflood system (Fig. 1) is about four years old and daily pumps approx&ately 110,000 bbl of oil-free sour water from a 3,700-ft deep reef. The

The Water Year Office for South Africa has supplied a provisional list of scientific congresses and meetings due to be held during 1970 with "Water" as the main or secondary theme, as follows: February: SARCCUS conference on "Water for Progress," Lourenco Marques. March 16-20: Annual Congress, Institute for Water Pollution Control, Cape Town. May: Possible S.A. Akademie conference on Cooling Tower Experiments, Pretoria. May: Annual Meeting of Association of Municipal Electricity Undertakings, Potchefstroom. May 27-29: Congress on "Water Resources of Natal", Durban. June 29/July 4: Annual Congress, South African Association for the Advancement of Science, Cape Town. July 2: Joint meeting of South African Association for the Advancement of Science and S.A. Akademie, Stellenbosch. July: Winter School, Federation of University Engineering Students. July: Youth Science Week. Foundation for Education, Science and Technology. July 21-24: The South African Tunneling Conference. September: Proposed SARCCUS conference on water in Nature Conservation, Skukuza. November 16-20: International Convention on "Water for the Future", Pretoria.

By T. M. Barczak, S. C. Tadolini

Reduction in the recovery time required and improvements in safety during a longwall face move have compelled coal mine operators to examine and use pre-driven longwall recovery rooms. The recovery entry is developed at the longwall stop position and supported ahead of time so that the required combinations of standing and internal supports can be installed before the longwall face approaches. A calibrated three-dimensional finite element model, developed in conjunction with an underground test area, provided the critical components and design principals for a comprehensive parametric study. The study indicates that vertical, horizontal, and shear stresses concentrated on the outby abutment pillar corner of the recovery room resulting in deformations in the immediate roof above the primary roof support anchorage level. The results of the numerical model and field site observations indicated that the combination of the internal bolting system and the standing concrete supports are critical for the successful and safe extraction of the longwall equipment. Cable supports installed at and angle over the pillars can help stabilize the disturbed zone above the adjacent fender and outby pillars, however; standing supports are required in most sedimentary roof conditions to increase stability and assure a safe longwall extraction.

By P. B. Baxendell, R. Thomas

Work on the calculation of vertical two-phase flow gradients by Cia. Shell de Venezuela has been based mainly on the "energy-loss" method proposed by Poett-mann and Carpenter in 1952. The "energy-loss-factor" correlation proposed by Poettmann and Carpenter was based on relatively low-rate flow data. This correlation proved inapplicable to high-rate flow conditions. In an attempt to establish a satisfactory correlation for high rates, a series of experiments was carried out at rates up to 5,000 BID in Cia. Shell de Venezuela's La Paz field in Venezuela, using tubing strings fitted with electronic surface-recording pressure elements. As a result of these experiments a correlation between energy-loss factor and mass flow rate was established which is believed to be applicable to a wide range of conduit sizes and crude types at high flow rates (e.g., above 900 BID for 27/8-in. OD tubing). It is anticipated that the resulting gradient calculations will have an accuracy of the order of % 5 per cent. At lower flow rates the energy-loss factor cannot be considered as constant for any mass rate of flow, but varies with the free gas in place and the mixture velocity. No satisfactory correlating parameter was obtained. As a practical compromise for low flow rates, a modification of the curve proposed by Poettmann and Carpenter was used. In practice this was found to give gradient accuracies of approxirnately ± 10 per cent clown to flow rates as low as 300 B/D in 27/8-in. tubing. INTRODUCTION Production operations in Cia. Shell de Venezuela's light- and medium-crude fields are principally concerned with high-rate flowing or gas-lift wells. Under these conditions the analysis of well performance, the selection of production strings and the design of gas-lift installations are vitally dependent on an accurate knowledge of the pressure gradients involved in vertical two-phase flow. Initially, attempts were made to establish the gradients empirically as done by Gilbert,' but the results were not reliable due to scarcity of data over a full range of rates and gas-oil ratios. Several methods of calculation based on energy-balance considerations were attempted, but the computations were cumbersome and the results cliscouraging. In 1952 a paper was published by Poettmann and Carpenter' which proposed a new approach. Their method was also based on an energy-balance equation. but it was original in that no attempt was made to evaluate the various components making up the total energy losses. Instead, they proposed a form of analysis which assumed that all the significant energy losses for mutiphase flow could be correlated in a form similar to that of the Fanning equation for frictional 1osses in single-phase flow. They then derived an empirical relationship linking measurable field data with a factor which, when applied to the standard form of the Fanning equation, would enable the energy losses to be determined. The basic method was applied in Venezuela to the problem of annular flow gradients in the La Paz and Mara fields" This involved establishing a new energy-loss-factor correlation to cover high flow rates and, also, some adaptation of the method to permit mechanized calculation using punch-card machines. The final result was 1 set of gradient curves for La Paz and Mara conditions which proved to be surprisingly accurate. With the encouraging results of the annular flow calculations, several attempts were made to obtain a corresponding set of curves for tubing flow. Here, unfortunately, little progress could be made. The original correlation of Poettmann and Carpenter was based on rather 1imited data derived from low-rate observations in 23/8- and 27/8-in. OD tubing. It did not cover the higher range of production rates, and extrapolation proved unsuccessful. A new correlation covering high flow rates was required, but this proved to be extremely difficult to establish since tubing flow pressure measurements at high rates did not exist—due to the difficulty of running pressure bombs against high-velocity flow. The necessity for reliable tubing flow data increased with the development of the new concessions in Lake Maracaibo, where high-rate tubing flow from depths of 10,500 ft became routine. Thus. it was decided to set up a full-scale test to establish a reliable energy-loss factor for tubing flow conditions. A La. Paz field light-oil producer with a potential of approximately 12,000 B/D on annular flow was chosen. To obtain full pressure gradients, a special tubing string was installed which was equipped with electronic surface-recording pressure measuring devices,

By Christodoulos Xiouris, Ali Reza, James Karnesky

A rocket parachute signal flare is often used to signal a maritime emergency. In the general operation of these devices, a solid rocket motor propels a metal body to an altitude of approximately 1000 ft(305m).At the end of the rocket motor, a propelling charge drives a signal flare and parachute out of the metal body and ignites the flare, which then burns for approximately 40 seconds as it falls to earth. In this paper, we describe an engineering investigation of an accidental ignition of a rocket parachute signal flare, which caused injury to the user. The components of the flare involved in the accident were inspected via x-ray and microscopic imaging techniques, and compared with those of unfired flares recovered from the same vessel. Chemical analysis of residue on recovered components from the accident flare was also performed. These comparisons were used to determine the likelihood that the actuation mechanism had been deliberately manipulated. In the subject model of the flare, ignition of the rocket motor is accomplished through a percussion cap which is struck by a firing pin. Prior to activation, the firing pin holds down a pre-compressed spring. We present a comparison of the ignition system of the incident flare with those of other rocket parachute flares, which do not incorporate any stored mechanical energy.

By R. J. S. Brown, B. W. Ganison

A new logging method has been developed, based on measurement of the nuclear magnetism of formation fluids. The nuclear magnetism log (NML) is the only log that responds solely to formation fluids. It operates equally well in both oil-base and water-base muds and in empty holes, and can be used in all kinds of formations except strongly magnetic ones. Two separate NML measurements can be made, one of which provides a continuous formation fluid curve. This fluid curve is called the free fluid log (FFL) and is believed to indicate a minimum effective porosity in most formations. The FFL not only delineates fluid-containing zones, but provides an excellent correlation curve that can be obtained under conditions where conventional correlation logs are ineffective. Preliminary tests indicate that the second kind of NML measurement may help distinguish oil and water zones and provide information concerning permeability and wettability. (The FFL itself appears to provide some information on permeability.) The second kind of NML measurement requires stopping the logging tool for a short time opposite a zone of interest and taking more extensive NML data that can be displayed as nuclear magnetic relaxation curves. In some instances, oil and water saturations for the region immediately adjacent to the borehole can be read from these relaxation curves. INTRODUCTION In 1946, Bloch, Hansen and Packard and Purcell, Torrey and Pound3 independently announced the successful demonstration of the phenomenon of nuclear magnetic resonance. During the past 13 years, there have been many applications of nuclear magnetic resonance, including applications to the study of chemical structure and to the measurement of magnetic field strengths. Preliminary experiments on the feasibility of using nuclear magnetism measurements in well logging were made independently by California Research Corp. and Varian Assoc., the Varian work being sponsored by the Byron Jackson Tools, Inc. Since then a cooperative research program on nuclear magnetism logging has been carried out by the Byron Jackson Div. and Research Center of Borg-Warner Corp., and California Research Corp., subsidiary of Standard Oil Co. of California. The use of nuclear magnetism in well logging is of special interest because it offers a way of making direct measurements on the hydrogen in the formation fluids and not on the rock matrix. Within the past 1 1/2 years, successful measurements have been made with a research model logging tool in wells in California, Tex as, Utah, Louisiana and Wyoming. NUCLEAR MAGNETISM SIGNALS Polarization, Relaxation and Precession Many atomic nuclei possess magnetic moments and spins; that is, they are similar in some respects to bar-magnet and gyroscope combinations. Molecules and their nuclei are subject to thermal motion, which has a scrambling effect, tending to leave as many nuclear spins oriented in any one direction as in any other. However, if a magnetic field is applied, the magnetic nuclei tend to align in the direction of the field. The scrambling and aligning forces compete with each other, with the result that a few more spins are oriented parallel to the field than in other directions. This gives a net magnetization, or polarization, which is directly proportional to the strength of the applied magnetic field (aligning influence) and inversely proportional to the absolute temperature (scrambling influence). When the magnetic field in, or temperature of, a liquid sample containing protons is changed, the new equilibrium value of proton polarization is not established immediately but requires an amount of time which depends on the nature of the hydrogen-containing materials. The process of approaching the equilibrium value of polarization is called relaxation.'.' Polarization is a vector quantity, and the components parallel to and perpendicular to the magnetic field must be considered separately. Relaxation of the component parallel to the field is called "thermal relaxation", or "longitudinal relaxation", and the corresponding time for this component of non-equilibrium polarization to decay by a factor of e (natural log base) is denoted T. The relaxation of the perpendicular component is called "transverse relaxation", and the corresponding relaxation time is denoted T,. The potential energy of a magnet in a uniform field depends on the angle the magnet makes with the field; therefore, a change of the component of net polarization parallel to the magnetic field involves an exchange of energy between the spin system and the thermal motion of the molecules, leading to the term thermal relaxation for the relaxation of this component. Suppose we subject a sample to a strong magnetic field at right angles to the earth's field for a time greater than TI. A polarization, thus, is established at right an-

By Andrew A. Blair

The increased importance and value of chemical analysis in connection with metallurgical operations is largely, if not entirely, due to the increased accuracy of the analytical methods used for the quantitative determination of the foreign elements always associated with the metal operated upon. This applies especially in the working of iron and steel, and to the determination of the amounts of such elements as phosphorus, carbon, and silicon. The influence of greater or smaller amounts of these elements upon the physical properties of iron and steel will be better understood when the proper experiments shall have been made upon samples whose chemical composition is known with almost absolute certainty. From the present standpoint of analytical chemistry, it is easy to see that at least one reason for the failure of many attempts to solve this problem, is the inaccuracy of the analytical methods used. Even at the present time the frequent want of agreement (over and above the unavoidable error due to manipulation) between chemists working on the same sample, leads one to think that there is still at least a choice in the methods used. It is true that very frequently a faulty method in the hands of a skilful analyst may be made to give corroborative results

By Thomas Novak, Robert Goldstein

The analysis of a machine-luminaire configuration is a time- consuming process requiring the construction of a machine mockup, installation of a designated lighting arrangement, and an extensive set of illumination measurements. This entire process, however, is well suited to computer analysis. By simulating the machine geometry and the characteristics of the desired luminaires, the incident light levels can be calculated at the required set of points. This Bureau of Mines paper presents a general description of the techniques involved in performing this simulation.

By J. C. Mostert, P. N. Roberts

Electric smelting at Rustenburg Platinum Mines Limited of nickel - copper concentrates containing platinum-group metals By J. C. MOSTERT Pr. Eng.. B.Sc. (Stellenboseh). M.Sc. Met. Eng. (Fellow) and P. N. ROBERTS Pr. Eng.. B.Sc. Eng. (Rand) (Fellow) The processes involved in the smelting in an electric furnace of nickel-copper concentrates containing platinumgroup metals are described. These are concentrate drying, pelletizing, pellet drying, and flux and pellets proportioning, followed by smelting of the concentrate in a submersible-electrode electric furnace, which is discussed in more detail. The furnace matte is blown in a converter to the white-metal stage and is cast in moulds, whilst the slag is granulated, ground, and floated for recovery of valuable metals and afterwards pumped to the tailing dam.

YEAR 1943-1944 Vol. 44 Page A major change-over in the ventilation of a deep level mine, by F. G. Hill and E. C. Ranson, 27; Discussion 56, 62, 67, 71, 72, 79, 123, 129 131 A note on the quarrying of surface limestone in the Sinai Desert, by V. L. Bosazza.. .. 59 Mining with diamond drills at the Nkana Mine of the Rhokana Corporation, Limited, Northern Rhodesia, by W. A. Odgers and A. G. Stirling, 95; Discussion 117, 121, 122 123 On silicates and dusts from the Witwatersrand gold mines (some preliminary notes), by J. J. Frankel, 169; Discussion .. 178 Presidential Address-Review of the rock pressure problem, by C. Biccard Jeppe, 3; Discussion 11,15 17 The chemistry, production and application of plastics, by P. N. Lategan, 138; Discussion 151 153 YEAR 1944-1945 Vol. 45 Page A microtechnique for the size-grading of mine dust, by S. R. Rabson, 34; Discussion 49, 50, 52 55 Activated carbon for regenerating used lubricating oil, by F. J. Tromp and J. J. Matthee 90 A contribution to the study of the production of zeolites, by C. C. le Grange and A. J. Petrick 235 A laboratory method for the determination of the suitability of South African coal and coal blends for the manufacture of metallurgical coke, by R. F. J. Teichmann .. .. 202 Copper containing cements for self-sanitising surfaces, by R. S. Young and H. L. Talbot 156 Notes on some sulphide minerals from the Far East Rand, by E. Mendelssohn, 84; Discussion, 88 89 Presidential Address-A review of underground support on the Witwatersrand with its Bearing on the Problem of ultradeep mining, by P. J. Louis Bok, 3; Discussion, 24, 25 27 Scientific management with particular application to a Witwatersrand gold mine, by J. S. Ford, 63; Discussion, 77, 80, 82 83 Some aspects of rock-drilling practice (the Witwatersrand gold field), by C. J. Irving, 163; Discussion, 185, 190 *197 Temperature measurements in a mine on the Witwatersrand with an electrical resistance thermometer, by O. Weiss, 127; Discussion, 136 137 The measurement of the geo-thermic gradient by means of the clinical thermometer, by R. A. H. Flugge-de Smidt, 105; Discussion, 136 137 The micro-chemical determination of free and combined silica in mine dust, by S. R. Rabson, 43; Discussion, 49, 50, 52 55 The oxidation of pyrites associated with South African coals, by R. F. J. Teichmann 141 YEAR 1945-1946 Vol. 46 Page Air cooling plant, No. 4 Shaft, City Deep, Limited. A review of layout and results achieved, by H. W. Unwin, A. Malcolm and R. E. Campbell Pitt, 66; Discussion, 100, 102, 103, 106, 110 115 A preliminary note on the Waterberg coal field as a possible source of coking coal, by P. E. Hall 124

By Peter Kovalchikb, Gregory Colec, Syd Peng, R. J. Matetic, Jeffrey Petersond

Mine Safety and Health Administration (MSHA) data indicates that the roof bolting machine is third among all equipment and second among equipment in underground coal mining whose operators exceed the MSHA-PEL (Mine Safety and Health Administration-Permissible Exposure Limit). In response to this, the National Institute for Occupational Safety and Health (NIOSH) has conducted a study to reduce overexposures of noise to operators of roof bolting machines. An important segment of the research is to determine, characterize and measure sound power levels radiated by a roof bolting machine during different drilling configurations. The determined sound power levels generated during the drilling cycle are of major interest because the levels represent the overall sound power generated by the machine. These sound power levels, determined from laboratory tests, can be used to accurately assess the effectiveness of proposed controls for reducing noise exposure to roof bolting machine operators. By using the sound power level results obtained from the laboratory and a commercially available acoustical modeling package, a method for predicting sound pressure levels to roof bolting machine operators for differing drilling types and parameters could be determined. This paper provides a method for predicting sound pressure levels at the operator’s position of a roof bolting machine in an underground coal mine using sound power levels determined in the laboratory. To determine validity, underground coal mine data was also collected to compare predicted and measured sound pressure levels. The results of the predicted sound pressure level data were the same as the underground measured results. This research will provide the mining industry with a valid method for predicting a roof bolting machine operator’s noise dosage underground given any type of drilling configuration or drilling method utilized from laboratory testing.

By Konstantina Chalastara

Mixed phase titanium dioxide (TiO2) nanoparticles synthesized through hydrolysis of TiCl4 solution at different conditions, namely concentration, pH, and residence time are characterized and evaluated as photocatalysts. The process is operated in a continuous stirred-tank reactor, CSTR giving blends of anatase, brookite, and rutile nanoparticles that were further evaluated to find the optimum mixture for a photocatalytic sorption material. The titania nanoparticles are first characterized in terms of photocatalytic activity under UV light illumination using an organic model compound (methyl orange) and after that are tested for removal of toxic selenate and selenite species from simulated effluent waters.