Search Documents

By W. C. Schafer

In tunneling or mining where hydraulic shields, moles, or rock boring equipment is used lasers such as those shown guide the production machine by providing a continuous and visible line and grade reference. In this application the laser may be mounted in the heading, preferably somewhere above spring line. If we view the circular heading as a compass in the vertical plane with 0º referencing at the crown of the heading and 180º on the invert, then it might be said that the laser may be mounted anywhere from 270º through 0º to 90º. The laser is generally mounted 2 to 3 ft off the wall or the crown of the heading by means of a bracket that may be attached directly to the liner plate. In cases where no liner plate is used, then brackets may be bolted directly into the ribs, or grouted directly into the rock. Once the laser is in position the beam is projected to the face. Two points must be surveyed upstream between the laser and the face which define line and grade. Targets may be suspended beneath each of these points approximately 2 to 3 ft. These targets may be circular or rectangular with a surface area which approximates 16 sq in. Each of these two targets should have a ½ to ¾ in. hole drilled directly in their center. When the laser is adjusted so that the beam passes through the holes in each of the two targets, the laser beam itself will parallel the center line of the tunnel and become a visible line and grade reference over the total beam projection.

Jan 1, 1970

By Jack Fox

Although this is going to appear in the December Issue of &E, it is being written long before the end of the year. December, of course, is the time for a summing up of the year's activities. Perhaps, the best way to begin is to report on what went on at the SME Board of Directors Meeting in St. Louis on October 20. This won't be a chronological report, and I shall take time to comment on some of the items we cover as we go along. You should be encouraged to know that your Directors take their duties seriously. Of the 21 current Directors, 19 were present, and three of the new 1971 Directors came to observe what goes on at an SME Board Meeting.

Jan 1, 1970

By E. T. Turkdogan, Klaus Schwerdtfeger, P. Grieveson

The rate of growth of "Fe4N" on a iron was measured by nitriding purified iron strips in flowing am -monia -hydrogen gas mixtures at 504" and 554°C. It is shown that a dense nitride layer is formed when a zone -refined iron is used in the experiments. With less pure iron, the nitride layer is found to be porous. Through theoretical treatment, the self-diffusivity of nitrogen is evaluated porn the parabolic rate constant, and found to be essentially independent of nitrogen actirlity, e.g., D* = 3.2 x l0-12 and 7.9x l0-12 sq cm per sec at 504" and 554?C. Some consideration is given to the mechanism of diffusion in the nitride phase. THERE is a great deal of background knowledge on the solubility and diffusivity of nitrogen in iron, and on the thermodynamics and crystallography of several phases in the Fe-N system. Although case-nitrided steels have many applications in practice, no work seems to have been done on the diffusivity of nitrogen in the iron nitride, ?', phase. The only work reported on the related subject of which the authors are aware is an investigation by Prenosil,1 who measured the growth rate of the e phase on iron by nitriding in ammonia-hydrogen gas mixtures. EXPERIMENTS Purified iron plates of approximate dimensions 1 by 0.5 by 0.03 cm were nitrided in flowing mixtures of ammonia and hydrogen, in a vertical furnace fitted with a gas-tight recrystallized alumina tube. After a specified time of reaction, the sample was cooled to room temperature by withdrawal to the water cooled top of the reaction tube. The furnace temperature was controlled electronically in the usual manner within *l°C; the temperature was measured using a calibrated Pt/Pt-10 pct Rh thermocouple. For each experiment the iron strip sample was cleaned with fine emery cloth and degreased with tri-chloroethylene prior to the experiment. The ammonia-hydrogen gas mixtures were prepared from anhydrous ammonia and purified hydrogen using constant pressure-head capillary flowmeters. The gas mixture flowed upward in the furnace with flow rate of 400 cc per min at stp. The composition of the gas mixture was checked by chemical analysis at regular intervals. In most cases, the compositions of the exit gas and metered input gas agreed within about 0.3 pct, indicating that cracking of ammonia did not pose a problem at the temperatures employed. Two series of experiments were carried out using two different types of purified iron samples. In the first series of experiments at 550°C, vacuum carbon deoxidized "Plastiron" was used. The main impurities present in this iron were, in ppm: 4043, 50-Cr, 20-Zr, 40-Mn, 20-P, 20-S, 20-C, 50-0, and 10-N. In these experiments the rate data were obtained by measuring the change in weight of the iron specimen suspended in the hot zone of the furnace by a platinum wire from a silica spring balance. The nitride layer formed in these experiments was found to be porous, particularly near the outer surface. In other experiments, high purity zone-refined iron (prepared in this laboratory) was used. The total impurity content of this iron was 30 ppm of which 20 ppm was Co + Ni, 4 ppm 0, other metallic impurities were less than 1 ppm. The zone-refined iron bar, -2.5 cm diam, was cold rolled to a thickness of about 0.03 cm and the specimens were prepared for the experiment as described earlier. After the nitriding experiment, the sample was copper plated electro-lytically and mounted in plastic for metallographic polishing. After polishing, the thickness of the ?' layer was measured using a metallographic microscope. The nitride layer formed on the zone-refined iron was essentially free of pores. RESULTS The different morphology of the nitride layers grown on "Plastiron" and zone-refined iron is shown in Fig. 1. Both samples were nitrided side by side for 55 hr. The holes in the less pure iron, Fig. l(a), are confined to a region about one half thickness from the outer surface. The dense layer grown on zone-refined iron, Fig. l(b), is thinner than the porous layer on the "Plastiron". The impurities in the iron are believed to be responsible for the formation of a porous nitride layer. The pore formation may be due to the high nitrogen pressures existing within the nitride layer, e.g., the equilibrium nitrogen pressure is 1.2 x l05 atm in the 38.6 pct NH3-61.4 pct H2 and 6.6 x l03 atm at the Fe-Fe4N interface at 554°C and 0.96 atm. It is possible that the oxide inclusions present in the electrolytic iron may facilitate the nuclea-tion of nitrogen gas bubbles within the nitride layer. Support for this reasoning is the fact that pores are only encountered in the outer range of the layer where nitrogen pressures are largest. The photomicrographs in Fig. 2 show the effect of reaction time on the thickness of the dense nitride layer formed on zone-refined iron. These sections are from samples nitrided in a stream of 29 pct NH3-71 pct H2 mixture at 554°C for 22, 70, and 255 hr. In all the sections examined the nitride-iron interface was noted to be rugged. These irregularities are be-

Jan 1, 1970

By Yuri D. Tretyakov, Robert A. Rapp

The stoichiometry ranges ofNiOl+y and LiFe,O,-d were established by high-temperatwe electrochemical meas7rements in a stabilized-zirconia electrolyte cell. The results were consistent with doubly ionized cation vacancies in NiO,+y and interstitial lithium or iron ions in . The defect structure of the ternary ferrite was derived from the consideration of equilibration with respect to oxygen between the solid and the gas phase. The absolute magnitudes of defect concentrations were calculated. Pavtial molar enthalpies of oxygen in the compounds were calculated and interpreted in terms of the enthalpy of defect formation in these crystals. NICKEL oxide (NiO,,?) is a metal-deficient, p-type, extrinsic semiconductor whose properties are consistent with a structural model based on the presence of cation vacancies as the predominant ionic defect at sufficiently high temperatures and oxygen activities. A survey of previously reported conductivity studies and the presentation of some more recent conductivity measurements will be given in a later paper.' The absolute magnitude of the equilibrium vacancy concentration in NiO has been reported from combined conductivity and thermogravimetric data of ' However, disagreement exists concerning the state of ionization of the nickel vacancies in NiO. Some authors3-' have proposed that the predominant defects in NiO are singly ionized nickel vacancies and positive holes (h') formed by the reaction where, accorhng to the notation of Kroger and Vink,6'7 Oq represents an oxygen ion on its normal lattice site. Other authors"27E have proposed that doubly ionized nickel vacancies (V{i ) and positive holes are predominant and are formed by the reaction One purpose of the present investigation was to establish the nature of the predominant defect in NiO,+? as well as its equilibrium concentration and thermo-dynamic properties at elevated temperatures and known oxygen activities. To accomplish this purpose, the coulometric titration of oxygen into and out of NiO was accomplished using a galvanic cell involving the calcia-stabilized zirconia electrolyte. The ternary oxide, lithium ferrite (LiFe50,-6) is ferromagnetic and has the inverse spinel structure LiFe,O,-d Thus, in the ideal stoichiometric XY204 lattice, Fe3 ions occupy one-eighth of the tetrahedral (A) sites, and i' and Fe3' ions share at random one-half of the octahedral (B) sites within the fcc sublattice of oxygen ions.g The structure and thermodynamics of the spinel structures have been comprehensively decribed.'-' A recent compilation of literature for lithium ferrite is also available. 15 Oxygen-excess LiFe50sis not expected to exist because both i' and 17e3& ions are in their highest normal valency states (positive hole formation is not favorable). As will be discussed, equilibration of the ferrite crystal with oxygen of a surrounding gaseous phase will result in the introduction of equilibrium concentrations of ionic and electronic defects. In the Results and Discussion section a defect model for LiFe50,-d is proposed. This defect model is tested by high-temperature coulometric titration experiments. EXPERIMENT The oxygen activities in nonstoichiometric NiOl+, (and also LiFe,O,-d) were measured by means of coulometric titration with the high-temperature galvanic cell The critical characteristic of a suitable experimental cell is the complete isolation of the phase to be investigated in a minimum sized chamber which is free from extraneous sources and sinks for oxygen (leakage). Then oxygen is only admitted to the chamber or removed from it in known amounts by coulometric titration, which involves the passage of oxygen ions through the solid electrolyte with electrochemical oxidation and reduction reactions at the platinum contacts to the electrolyte. The experimental cell is shown in Fig. 1. The cap of the cell was the tip from a closed-end alumina tube, which was found to be leak-free from a helium leak-detector test. This alumina cap was about 1.2 cm OD and about 1.5 cm high. A Zircoa calcia-stabilized zirconia tablet (crucible lid) of 1.5 cm diam and 0.3 cm thickness served as the solid electrolyte. A Pyrex ring of about 0.1 cm thickness was placed between the electrolyte and the cap. The electrolyte tablet was painted with platinum paste on the entire outer face and on that part of the inner face which would be within the enclosure; these electrodes were further prepared by heating in air at 1000°C for 2 hr. Nickel oxide powder, listed as 99.999 pct pure, was purchased from Leico Industries, Inc. Pills of the NiO were cold-pressed and sintered at 1050°C for 3 hr in a platinum crucible. This poorly sintered NiO was crushed, and chunks were wrapped in 52-mesh Pt gauze (to catalyze the solid-gas exchange) for place-

Jan 1, 1970

By C. W. Volek, J. E. Chappelear

The injection of a hot liquid into initially cool porous media, saturated with the same liquid and surrounded by two impermeable but heat conducting media (cap and base rock), has been studied both experimentally and theoretically. The temperature dependence of the viscosity was included in the theoretical model, but it was assumed that the specilic heats and densities of the various materials were independent of the temperature. Solutions to the theoretical model were approximated by numerical methods. Both theoretical and experimental results indicate that center-line temperatures are significantly higher than boundary temperatures. Comparison of experimental and theoretical results with a cold/hot viscosity ratio 01 19:1 were in reasonable agreement. Theoretical calculations show that the effect of the temperature dependence of viscosity was very significant at ratios of 100:l to 1000:1, which are typical of those that occur when injecting hot water to flood heavy oil reservoirs. INTRODUCTION We consider the problem of prediction of fluid flow and temperature distribution in an initially cold-fluid-filled reservoir on the injection of the same hot liquid by the use of mathematical and physical models. The results reported are for a two-dimensional rectangular section of the reservoir, as shown in Fig. 1. The injection and withdrawal faces are assumed to be equipotentials for fluid flow. The ultimate purpose of such models would be to predict hot-water injection performance. However, we note that in the work presented here, one of the most significant aspects of the problem — the instabilities resulting from two-phase, water and oil flow — is not included. We will not give a historical review, but refer instead to the paper of Spillette and Nielsen,1 which contains a rather complete bibliography and critical discussion. The physical problem is exactly the same as Spillette and Nielsen, except for certain simplifications in our assumptions. The mathematical details are somewhat different, and we will present the details of our method here. The mass flow equation, which is elliptic in character, is handled by successive overrelaxation. The heat flow equation, which is parabolic in character, is handled by a straightforward explicit approximation. Some difficulty arose in the over-all heat balance due to small errors in the solution of the mass flow equation, and we feel that a different formulation of the heat flow equation would be desirable for future work. In addition to the mathematical solutions for the temperature distributions in a porous medium due to the injection of hot liquids, experimental data are presented to check the validity of these solutions. A schematic diagram of the model is shown in Fig. 2. Certain qualitative physical conclusions were obtained from our numerical and experimental results. These are: 1. Assuming high (infinite) conductivity normal to the bedding plane in the reservoir is a poor approximation, and may lead to overestimates of the total heat losses (to cap and base rock) of as much as 50 percent. 2. More heat is retained in the reservoir (per unit of heat injected) for higher viscosity changes. 3. Any particular temperature isotherm moves more rapidly along the center line for higher viscosity changes. Consequently, the approximation of temperature independent viscosity is not suitable for obtaining quantitatively correct results. MATHEMATICAL MODEL Our mathematical model is that of a reservoir of thickness 2h. The problem is idealized from that of a linear hot-water drive, and we imagine that the input face is sufficiently far away from the injection wells that the stream lines enter it normally. Similarly the production wells are far enough from the outflow face that the flow lines leave it normally. The reservoir and surrounding cap and base rock

Jan 1, 1970

By Klaus Beckmann

Gentlemen : My object reads "Longwall Rapid Advance of Coal Mining in the Federal Republic of Germany". It is true that the percentage of coal obtained in your country from longwall faces, with at present 1.2, is still rather low, but it increased considerably since 1966 with 0.4 %. The coal mines of the Federal Republic of Germany ever used longwall as the classical method of coal getting. All attempts to introduce bord and pillar mining did not lead to any wider application of this method. The principal reasons, for this appear to have been: - the deeper depth of our workings, - the wish to keep working losses as low as possible and to utilize the deposits opened up by deep and therefore expensive shafts to the furthest possible degree, - the dense sequence of seams and the mutual influencing of the working points, - the high number of disturbances in the geologically much stressed deposits, - and the necessary considerations to the protection of the densely built-upon surface.

Jan 1, 1970

By J. D. Livingston, H. E. Cline

The lamellar-dendritic transition in Sn-Pb alloys near the eutectic composition has been studied at high growth rates. Lamellar structures were found over a substantial range of tin-rich compositions, and this range extended to increasingly tin-rich concentrations as growth rate increased. These results are discussed in terms of stability and competitive-growth arguments. Various experimental and structural limitations to the rate of directional solidification are discussed. The rate of heat removal at the heat sink is the major experimental limitation. ReCENT interet1,2 in the use of fine composite structures produced by directional solidification of eutectic alloys makes it important to determine the range of composition and growth conditions that yield such microstructures. Because increasing growth velocities produce increasingly finer microstructures, it is particularly significant to determine the factors limiting the rate of solidification. Mollard and Flemings3 have shown that composite structures, free of primary dendrites, can be obtained in Sn-Pb alloys of off-eutectic composition. The composition range of composite structures was found to increase with increasing values of G/V, where G is the temperature gradient and V is the growth velocity. These results are in good quantitative agreement with an analysis of the stability of a planar eutectic interface.4 This analysis specifically predicts that over a small range of compositions stable lamellar structures will be obtained even for G/V = 0, hence, even at very high growth rates. The lamellar-dendritic transition in Sn-Pb alloys has also been analyzed with a model based on competitive growth between dendrites and the composite structure.576 This treatment, based on earlier work on organic eutetics,7 predicts that the composition range yielding composite structures in Sn-Pb will increase rapidly at high growth rates. An increase in the composition range of composite structures at high growth rates was recently observed in Cu-Pb alloys near the monotectic composition.8 In view of these results, and the predictions of the stability and competitivegrowth analyses, it was decided to study the lamellar-dendritic transition in Sn-Pb alloys at high growth rates. EXPERIMENTAL Using 99.999 pct pure materials, a series of Sn-Pb alloys were prepared containing 16.8 at. pct to 27.6 at. pct lead. (Eutectic composition is 26.1 at. pct Pb.) Ingots were extruded to 0.175 in. rod, and some rod was drawn to 0.070-in. wire. Directional solidification was accomplished in two different ways, Fig. 1. For growth rates up to 2 x 10-1 cm per sec, a 0.175 in. diam sample was placed in a graphite crucible 5 in. long with 0.250 in. OD and 0.035 in. walls. Samples were melted under flowing argon in a vertical, platinum-wound furnace, and solidified by driving the crucible downwards through a \ in. hole in a water-cooled copper toroid, Fig. l(a). An insulated chromel-alumel thermocouple was imbedded in the center of a representative sample, and moved with the sample during solidification. The local temperature is plotted against the distance travelled by the sample in Fig. 2. As the growth rate increased, the solid-liquid interface moved closer to the water-cooled toroid and the temperature gradient increased. At growth rates above 10-1' cm per sec, heat was not removed fast enough and the sample moved into the toroid in the liquid state. The curve for V = 2 x 10-1 cm per sec shows a plateau caused by incomplete removal of latent heat from the interface, a problem which will be discussed later. To improve the heat removal, the toroid was cooled by nitrogen gas precooled in liquid nitrogen. This allowed successful solidification at rates up to 2 x 10-1cm per sec. Higher solidification rates required still more effective heat removal. Samples 0.070 in. in diam were placed in graphite tubes 0.125 in. in diam with 0.020 in. walls. Instead of cooling by sliding contact with a cooled toroid, these thinner samples were sprayed or directly immersed into water, Fig. l(b). After solidification, samples were stored in liquid nitrogen until they could be examined metallographic-ally. The surface was prepared with a diamond-knife microtome, followed by a light etch. The presence or absence of tin dendrites, Fig. 3, or lead dendrites, Fig. 4, was noted by optical microscopy, usually of a transverse section near the center of the sample. Replicas of the surface were prepared and examined in an electron microscope to resolve the fine lamellar structures, Fig. 5. The structures observed at various compositions and growth rates are summarized in Fig. 6. Composite structures were observed at increasingly cin-rich compositions as growth rate increased. This transition from dendritic to composite structure with increasing growth rate was also demonstrated by solidifying half a sample at a slow rate and then suddenly increasing the growth rate by lifting the furnace and quenching the sample with a water spray. A longitudinal section of this sample, Fig. 7, shows that the tin dendrites, which extended ahead of the slow-moving composite interface, were bypassed by the composite when the growth rate was increased. The range of composite structures at high growth rates was limited by the appearance of primary lead dendrites on the tin-rich side of the eutectic composition. Observation of representative longitudinal

Jan 1, 1970

By G. C. Hancock

The operating plant of The Broken Hill Associated Smelters Pty. Ltd. is situated at Port Pirie in South Australia and it treats to finality the whole output of lead concentrates from the mines of The Zinc Corporation Ltd., North Broken Hill Ltd., and aroken Hill South Ltd. at Broken Hill, New South Wales. Lead bearing ores from other sources are also purchased for treatment and lead scrap and residues are treated on a toll charge basis. The present output of the plant is approximately 200000 tonnes of refined lead per annum and there is a substantial production of by-products including refined silver, gold, cadmium, antimonial lead alloys, copper matte and sulphuric acid. Recently the Company commenced the production of zinc by slag fuming and electrolysis from a six million ton dump of lead blast furnace slag, which has been accumulating at Port Pirie for over fifty years. The slag fuming plant contains two furnaces of conventional design, but features a high degree of pre-heat for the blast air and this is obtained by the use of all-metal recuperators. The raw zinc oxide fume produced by the plant is roasted in a rotary kiln prior to treatment in the leaching and electrolysis sections, which follow conventional practice for nigh current density plants. Present output is approximately 36000 tonnes of electrolytic zinc per annum.

Jan 1, 1970

By C. B. Manula, H. Gezik

In planning modem-day mining operations, management needs to pass from the area of subjective decision-making to an area of objective decision-makirlg. Planning procedures currently being practiced by many mine managers depend primarily on common sense and trial-and-error methods which oftentimes never reach optimum solutions. For this reason, an attempt is made to provide an understanding of linear programming to solve production planning problems. More specifically, a linear programming model is proposed to solve the production scheduling problem as it was found to exist in the crushed stone industry. Optimal production scheduling is of prime concern here, since the industry has to cope with seasonal demands for its products. The solution, as determined through the application of the model, provides management not only with an optimal production schedule but also with the following information regarding the improvement of existing facilities: (I) the location of bottlenecks which limit production and profit; (2) the directions in which the company i fixed equipment should be expanded or modified; and (3) the evaluation of unused resources. Future trends in stone production will quite likely parallel those in the construction industry. Continued record expenditures for structures such as dams, highways, and buildings are the reasons for this accelerated growth. Production forecasts for the next decade are predicted to be around one billion tons with an approximate 7% annual increase. The problem of increasing production from 570 million tons in 1966 to 1 billion tons by 1976 offers no small challenge. This situation is further compounded by other problems and economic factors. Population expansion, government regulation, labor agreement, and changes in technology wd cause managers and operators to be confronted by many more complexities than characterize present-day operations. Some of these. problems and economic factors are: (1) In some metropolitan and other urban areas, easily accessible sources of stone are almost depleted. Transportation costs will be a prime concern of the industry. (2) Population growth has forced residential expansion to a point where many quarry operators must conform to urban and suburban regulations. (3) Government regulation in regard to air and water pollution, noise, and reclamation as well as zoning developments necessitate that crushed stone producers keep abreast of changing conditions and requirements. (4) The crushed stone industry operates under pressure of a highly competitive situation. Every company's objective is to retain a favorable marketing position by exercising great attention to production and marketing costs. This is rather difficult, since the crushed stone industry is one segment of modern mining which has to cope with a seasonal demand for its products. Among the problems posed here, the one of exercising great attention to production and marketing costs is of current interest to management. Under seasonal demand conditions, this problem creates further difficulties for managers who need to plan and forecast. STATEMENT OF THE PROBLEM Various methods of Operations Research have been developed to handle a problem whose genesis is explained above. It is very seldom, however, that these quantitative means are used in practice by the mining industry. This paper describes the use of Operations Research methods to solve a production planning problem when demand is seasonal. The seasonal production planning problem is an important one because of the substantial costs associated with changing production, employment, and inventory levels to adjust to seasonal sales patterns. Most companies try to operate within reasonable levels of employment changes and hold inventories within storage capacities. In general, little or no attempts were made to develop minimum cosl schedules or to provide objective means to compare various production policies. When demand varies within a fixed time period, 11:-oduction requirements may be met by following one

Jan 1, 1970

By I. Spector, A. J. Smith

In 1967, BACM Industries Limited started producing walboard at Saskatchewan's first gypsum products plant, located in Saskatoon, using, as a basic raw material, gyp-sum rock supplied from the company's mine near Amaranth, Manitoba. This paper describes the geology of the Amaranth gypsum deposit, the method of mining the rock and the manufacturing facilities used to produce wall-board.

Jan 1, 1970

By M. N. Shetty

LARGE copper whiskers were grown from cuprous iodide by reduction with hydrogen at about 500°C. Carefully selected single-crystal whiskers of [loo], [110], and [Ill] orientations were used and the whisker shapes and cross sections are shown in Fig. 1. Spec-trographic analysis of a typical batch of whiskers showed that the composition was better than 99.9 pct with iron and silicon as the major impurities. The test specimens varied from about 70 to 400 u in diam and they did not show a conspicuous yield drop as observed in very fine whiskers (diam <25 u), tested by Brenner.1 The characteristics of the stress-strain curves were similar to those of bulk single crystals, even though the maximum flow stresses reached in some orientations were comparable to the yield stresses observed in fine whiskers. Mechanical properties of whiskers of different materials and copper whiskers up to about 100 u in diam have been reviewed,&apos; and a mechanism of slip band propagation in fine whiskers has been recently suggested.3 Whiskers in this work were tested in a floor-model Instron testing machine using low strain rates. (Details of the testing procedure, diameter dependence of the yield stress, and the characteristics of the load elongation and stress-strain curves have appeared esewhere.4) Due to the extensive deformation, >50

Jan 1, 1970

By Freeman Bishop

The Interior Department has been in a state of disarray for many months. At first this was attributed to Interior Secretary Walter Hickel&apos;s inability to anticipate how his words would be interpreted by Press-Radio-TV. But then the already disquieted ernployees in the Department became aware that plans were afoot to take bits and pieces of the various antipollution programs from Interior; Health, Education and Welfare: the Atomic Energy Commission and other agencies and lump them together into a new Federal agency. Interior, many predicted, would be a shell of its former robust self. Hardly had this rumor started to add to employee uneasiness before the other big shoe hit the floor. The new rumor had it that the Bureau of Mines was being stripped of most of its research functions and that the Office of Coal Research and allied research groups would be abolished altogether.

Jan 1, 1970

By Roland W. Rammler

In recent years, the crude oil reserves of the world have increased at the same rate as the consumption. A Consideration of the global figures suggests that adequate supplies of petroleum will be available during the next decades. On the other hand, it in a fast of economic and political significance that the reserves in the industrialized countries increase much more slowly than in the developing countries. In Western Europe the reserves have even decreased. At the present time, about 70 % of the petroleum reserves of the world are in the Middle East and in Africa in regions in which political arises are prevalent or impending. For the industrialized countries, the discrepancies between the consumption and reserves in various regions of the world are a strong urge to investigate whether oil can be recovered from other sources. The situation will probably not be changed to a large extent by the discovery of oil in the north of Alaska. The main starting materials for the production of synthetic crude oil are coal, oil shale and tar sand. In North America, where the consumption of petroleum increases more rapidly than the reserves, there are enormous deposits of each of the three materials. This fact is another incentive toward the utilization of these unconventional oil reserves, which provide a reliable basis for a supple of energy for a long time to come.

Jan 1, 1970

By Ashok K. Sinha

During the course of an in~*estigation into the occurrence of ordered AB3 structures, the following new phases have been found —CrRh3 (AuCu3 type), CrCo3 (MgCd3 type), HfCo4 (Ths Mn23 type), and WPt, MoPh type). The composition of the TiPt3-x phase (TiNi, type) is close to Ti23Pl77. The alloy chenzistry of transition rnetal AB3 structures is rezliewed in the light of electron concentration correlations of hex-agonality recently obtained for quasi-binary alloys. The relatizte colurne contraction in the AB3 structures increases with increasing difference in volume of the conzponents. A family of ordered close-packed layered structures is formed by stacking identical layers of composition AB, in various sequences, such that the coordination is twelvefold throughout and there are no A-A contacts. Previous work&apos; on quasi-binary AB3 alloys has led to the conclusion that the stacking sequence of the AB, structures changes with increasing radius ratio RA/RB from a purely cubic, through different mixtures of hexagonal and cubic stacking to a purely hexagonal stacking. However. for binary AB3 alloys, a correlation between the type of the crystal structure and the position of the components in the various volumns of the periodic table has been noted.2-5 It has been noted6 that this correlation appears to hold even though the radius ratio RA/RB may vary over a considerable range with the location of the components in the three long periods. Another study7" of several quasi-binary systems led to the conclusion that an increase in hexagonality of the stacking is associated with increase in the electron concentration e/a. as defined by the average per atom of the total number of electrons outside the inert gas shells. In apparent conflict with this conclusion, it is known that seven binary alloy structures isotypic with TiNi3 which is 50 pct hexagonal occur at a higher electron concentration (e/n = 8.5) than that (e/a = 8.25) for the 100 pct hexagonal MgCd3 type structure present in seven binary AB3 alloys. Table 111. In the present work, an investigation into the occurrence of binary AB3 structures in transition metal alloys was made, and a survey of binary AB3 structures is presented. EXPERIMENTAL The starting materials were pure metals of 99.9 wt pct purity. The alloys were arc-melted under partial pressure of argon and annealed in sealed silica capsules lined with molybdenum foil under argon at- mosphere. The total weight loss upon melting and subsequent annealing was always less than 1 pct and hence the alloys will be referred to by their intended (unanalyzed) compositions. Wherever the constitution permitted. the alloys were given a homogenizing treatment at 1200°C (3 days) prior to annealing. Unless otherwise stated all alloys were annealed at 900°C for 1 week and water-quenched. Sometimes the final annealing treatment was carried out on powders to accelerate the attainment of equilibrium. X-ray powder patterns were taken using a Guinier-de Wolff focusing camera (CuK, radiation) or an asymmetrical focusing camera (Co or CrK, radiation). For lattice parameter determination. internal silicon standards were employed. The intensity calculations were made using a Fortran IV program written by Jeitschko and parthe.9 RESULTS Twenty AB3 and three AB4 alloys were investigated. Table I lists the crystallographic data on some of the intermediate phases encountered in the present work. Table II contains the X-ray data for HfCo, (Th,,Mn,, type). The positional parameter, x. was assumed to be 0.378. the value for Th6Mnn2310 The X-ray pattern of ZrCo, was very similar to that of HfCo, and the previous structure determination of ZrCo, by Kuzma el al." was confirmed. Ordering in the alloy CrCo could be ascertained by the presence of only one weak super lattice line (101). the others being too weak presumably owing to the small difference in the scattering powers of chromium and cobalt. This line was observed in the X-ray pattern of powder from the massive sample annealed at 830°C (7 days) after the powder had been reannealed at 600°C (24 hr). The diffraction pattern of the powder similarly reannealed at 830°C (24 hr) contained only the lines due to a mixture of hcp and fcc Co(Crj solid solutions. Therefore, it appears reasonable to assume that O2 and/or N2 contamination which would be less likely to occur during the 600°C anneal was not responsible for the observed weak reflection. Also. this reflection cannot be identified with any of the strong lines of the neighboring s phase which is present in the Co-Cr system at higher chromium contents. The composition corresponding to the TiNi3 structure observed by Raman et al.12 in the two-phase alloy Ti,zt,, has been established in the present work as being between There was satisfactory agreement for the low-angle lines (up to d = 1.997A) between the observed diffraction pattern of TiCua and that calculated assuming the ZrAu, structure. as recently proposed by Pfeifer-et a1.I3 However. some of the superlattice lines. e.g., at d = 1.937 and 1.919A. predicted by the ZrAu, structure were not actually observed eve? though neighboring lines. at d = 1.947 and 1.986A. of comparable calculated intensity were present. The ZrAu

Jan 1, 1970

By Samuel S. Adams

Economic concentrations of potassium are essentially limited to thick, stratigraphic sections of marine evaporites. These deposits were precipitated through the evaporation of sea water in restricted epicontinental seas or in grabens related to continental margin rift systems. Following deposition the deposits were subjected to diagenesis and varying degrees of metasomatism and structural deformation. The origin and characteristics of potash deposits are easier to study and interpret than those of most ore deposits because the phase chemistry of the salt systems is known and the approximate composition of the ore-forming fluid (sea water) can be inferred with confidence. It is particularly helpful that the temperature and pressure of deposition approximated that of present earth surface conditions and the pertinent mineral assemblages can readily be duplicated in the laboratory. The study of these comparatively simple salt deposits provides examples of the practical advantages of understanding the genesis of an ore deposit. These observations, in turn, illustrate the importance of pursuing research on the more complicated magmatic, hydrothermal, and ground-water systems as a means to the more successful exploration for and exploitation of the deposits they have produced. It is the purpose of this paper, therefore, to discuss certain aspects of salt deposit geology as they contribute to exploration and mining through some understanding of ore formation. References to field examples and chemical relations in the salt systems are brief. All examples are more fully discussed, however, in the references cited.

Jan 1, 1970

By A. T. Yu

Bulk sampling is define&apos; as the ?process of extracting a small fraction of material from a large bulk ...sufficiently representative ...for the intended purpose.? (ref. 1). Today&apos;s pressing need for simple, effective and reliable sampling systems is intensified by the growing demand for quality control as a means to cope with inflation, competition and rapidly increasing consumption of raw materials. Much has been written on bulk sampling (ref. 2 thru 9). It involves a wide range of subjects cutting across the domains of physics, chemistry, geology, mining, materials handling and processing, as well as probability and statistics. Since the problem itself is complex, any in-depth treatment cannot avoid a somewhat lengthy coverage. Of all of the related topics. Arbitrary, haphazard studies, on the other hand, can leave out important details and obscure or confuse the issue.

Jan 1, 1970

By Earl R. Hoskins, James E. Russell

The electrical resistivity of rocks has been studied quite extensively, in particular, the effects of temperature and confining pressure on resistivity. References 1 through 6 at the end of this chapter pertain to electrical resistivity of rock and contain further references on the same topic. The present study is motivated by an interest in determining the in-situ properties of rock as well as the stress state of the rock and how these quantities are changing with time. Most of the previous work on the electrical resistivity of rocks has been directed toward saturated rocks at relatively high confining pressures and temperatures. The present study was oriented towards air-dry surface rock that might occur in mine pillars. The mean stress and temperature under such conditions are comparatively low. It has been demonstrated that the resistivity of rock is highly dependent upon the porosity. In fact, for saturated rocks, a relationship referred to as Archie&apos;s law has been established between porosity and electrical resistivity. In the case of saturated rock, the property that is actually being measured is the resistivity of the solid/fluid system. Since the resistivity of the fluid alone is usually much lower than that of the dry rock, it is understandable that the resistivity of a saturated rock is in general several orders of magnitude lower than the resistivity of a relatively dry rocli. For dry rock, it seems reasonable that the electrical resistivity should increase as microcracks open within the material. Since microcracks open as material is stressed closer and closer to its failure point, it appears that there should be a correlation between electrical resistivity

Jan 1, 1970

By Freeman Bishop

The House Ways and Means Committee recently heard a bitter dispute over whether gasoline with lead is a worse pollutant than gasoline without lead. The lead industry is also squarely in the middle of this dispute for obvious reasons. Lead used in gasoline amounts to 270,000 tpy, or more than 254 of the annual total mined in the U.S. Few industries can face the loss of such a market without wondering how they are to stay in business. The lead industry picked up unexpected support in this dispute, however, when the AFL-CIO stepped up with outright opposition to the President&apos;s proposal to tax lead in gasoline.

Jan 1, 1970

By W. J. Maraman, D. R. Harbur, J. W. Anderson

A device for rapidly quenching liquid metals into thin platelets has been developed at the Los Alamos Scientific Laboratory. This rapid quenching equipment is built around the technique of catching a molten drop of metal between a rapidly closing plate and a stationary plate. The design and operation of this unit are described. The closing speed of the smasher plate at impact is 12.6 ft per sec. The quenching rate for this device is controlled by the interface resistance between the plates and the platelet, and is dependent upon the heat content and density of the material being quenched. The initial quenching rate down to the freezing point of the platelet material is lo5º to 106ºC per sec. After an isothermal delay, which is poportional to the heat of fusion of the platelet material, the final cooling rate down to the temperature of the smaslier plates is l04ºto 105cº per sec. RAPID heating of metals by capacitor discharge and other methods has provided the metallurgist with a useful tool for probing into the kinetics of phase changes and the many nonequilibrium phenomena which occur during rapid temperature changes. Equally interesting studies can also be made on metals and alloys which are rapidly cooled from the liquid state.&apos; Studies in this field have been limited, however, because the rates at which metals could be cooled were many orders of magnitude slower than the rates possible for heating. In recent years many new laboratory methods have been developed to rapidly cool metals from the liquid state to ambient temperature and below.2"4 All of these methods involve spreading a liquid drop of metal into a thin foil in a very short time. The methods developed have varied from ejecting a drop of molten metal at the inside surface of a rotating cylinder or stationary curved plate to catching a falling drop of molten metal between rapidly closing plates. The equipment which has been developed at the Los Alamos Scientific Laboratory for rapidly cooling molten materials uses the latter of these two approaches. The basic design, operation, and initial results of this rapid quenching device are given in this report. APPARATUS The drop smasher, which is now being used to obtain rapidly cooled metal foils, is shown in Fig. 1. Basically the device consists of a smasher plate which is driven by a solenoid into a stationary plate. The solenoid is activated by a drop passing through the photoelectric cell and is powered by discharging an adjustable 350-v capacitor bank with a 66-amp peak current into it. This power supply is designed so that the solenoid is powered for 2 m-sec after plate closure to minimize the rebound effect. There is an adjustable time-delay mechanism between the photoelectric cell and the solenoid. Both smasher plates have changeable inserts so that a variety of materials can be used to smash the molten drop. The shaft of the moving plate is guided in an adjustable housing which has ball-bearing walls. The cabinet shown to the left of the drop smasher in Fig. 1 contains the power supply and receiver for the photoelectric cell, the time delay mechanism, and the capacitor bank. The drop smasher can be placed inside a vacuum chamber, for use with radioactive materials, with the upper plate forming the lid, as shown in Fig. 2. On top of the vacuum lid is an induction coil, powered by an Ajax induction generator, which is used to melt drops from the end of the rod extending through the vacuum seal on top the quartz tube. OPERATION The drop smasher shown in Fig. 2 is operated in the following manner. The smasher plates are separated and the unit is lowered into the vacuum chamber using a pressurized cylinder. The induction coil, quartz tube, and lid with sliding vacuum seal are then assembled on top the vacuum chamber. A rod of the material for rapid quenching studies is connected to the rod extending through the sliding vacuum seal. The vacuum chamber is then evacuated and the desired atmosphere established. The photoelectric cell is turned on, and the capacitor bank is charged and armed. Power is supplied to the induction coil, and the rod of material for rapid quenching studies is lowered into the induction field. A molten drop forms on the end of the rod, drops off, falls through the light beam of the photoelectric cell, and is then caught between the smasher plates. .

Jan 1, 1970

By John V. Beall

It is difficult to understand why they did it. It was a demonstration of total commitment which sent chills of mixed admiration and fear up and down your spine. The scene was the bodega in Section A, 2660 Level on the 12 to 8 shift. The jefe was patiently waiting for the tea leaves to settle in a large metal cup. His attention was distracted by the appearance of a miner who had a problem. The long and short of it was that the miner believed the branch raise he was driving was unsafe and he wanted the jefe to come and see it. After lunch the jefe went around. First cautiously shining his light to peer up the raise from outside the chute, he then scrambled inside and swiftly climbed the cribs to the face. No question, it was hairy; about 4 crib sets were needed to catch up to the face. The unsupported raise was slabbing. It didn&apos;t take the jefe more than a few seconds to ascertain this situation and to slide back down. As he came out of the chute, a small avalanche arrived on his heels and provided a sort of exclamation point to his order; "cerrado!" In other words, shut &apos;er down.

Jan 1, 1970