Search Documents

Collins Radio Company, through this contract with the Bureau of Mines, has conducted a System Study of Coal Mine Communi¬cations. The program was a three phase program to establish a data base, perform communication system analysis and optimi¬zation, and prepare equipment specifications to be included in this final report. At the start of establishing a data base both a knowledge of mine communication and coal mines in general was obtained. Communication system requirements and constraints were determined along with a survey of current and potential mine communication equipment. An investigation was completed concerning theoretical LF and VLF propagation characteristics, and UHF propagation tests were conducted in a working coal mine. Different mines were contacted and on-site surveys completed with respect to coal mine communication requirements.

Jan 1, 1973

By J. R. Katan, J. R. Ball, Peter R. Bannister, F. J. Williams

During the last week in March and the first week in April, 1973, the Naval Underwater Systems Center measured the 76 Hz magnetic field strength (in Wisconsin and Texas) produced by both the elevated and (newly installed) buried Wisconsin Test Facility (WTF) north-south (NS) antennas. The principle result obtained from these measurements is that there is no measurable difference in performance between the WTF buried and elevated NS antennas.

Jan 1, 1973

By W. K. Overbey

Surface fracture trace density, changes in roof rock type, and topographic unloading due to drainage were mapped for the mining areas located in the Blacksville-Osage, W. Va., quadrangles to investigate their influence on mine roof falls. Using these factors, a technique was developed to predict probable roof fall areas ahead of projected mining operations. As a feasibility test of this proposed technique, areas were delineated where one, two, and all three of these factors were operating to formulate a "potential hazard map" for comparison with roof fall observations that were made. The limited evidence suggests that in combination these factors are reliable predictors of where roof falls are likely to occur. This technique promises to be a useful tool in planning mining operations.

Jan 1, 1973

By A. W. Hall

A nuclear method was developed for continuously and automatically deter-mining the moisture content of coal flowing through a bin. Fast neutrons from a 1 curie americium-beryllium source penetrate the coal, are thermalized (slowed down) by hydrogen in the moisture, and are counted by a thermal neutron detector. The difference between the number of these thermal neutrons and those thermalized by dry coal (in a reference drum) is a measure of the moisture content of the coal. A materials handling system was developed and in tests at a commercial coal preparation plant, moisture in coal was monitored continuously within 0.2 percent of values determined by conventional means. The meter responded rapidly to change in moisture content, making it adaptable to automatic process control, and was operated for 1 year without malfunction or recalibration. Shielding of the source by the coal kept the neutron flux level at the bin wall less than 1 milliroentgen per hour, a safe level for personnel.

Jan 1, 1973

By J. J. Knoerzer

The scheduled replacement of Inland's A & B coke batteries in Plant No.3 posed some serious problems in terms of pollution control and strained sources for medium volatile coal for a conventional blend. The state-of-the-art of air pollution control during the charging step in the conventional slot-type coke oven has been less than satisfactory. In addition, the work done at the Illinois Geological Survey showed that by preheating the coal blend prior to charging a greater percentage of Illinois coal could be used to produce a high quality metallurgical coke. To assist The Management in the- decision on A & B replacement, Inland Steel conducted a full-scale test program on coal preheating and pipeline charging utilizing the Coaltek system installed on No. 2 battery of the Semet-Solvay Division of Allied Chemical Corporation. The basic objectives of the test program at Semet-Solvay were as follows: 1. Determine the feasibility of producing high grade metallurgical coke from preheated blends containing more than 60% Illinois No. 6 coal. 2. Confirm the performance characteristics in one of the Inland blast furnaces of the coke produced with 75% Illinois coal in the blend. 3. Verify several claims by Coaltek such as: a) Pipelining the hot coal presents no difficulties while essentially eliminates the air pollution problems associated with the conventional charging system. b) Preheating of the coal blend permits the use of higher percentages of high volatile, marginally coking coals (such as Illinois No. 6) in the blend as compared to wet charging.

Jan 1, 1973

By M. Hertzberg

Results of a comprehensive study of the absolute spectral radiance of the infrared emissions from methane-air explosions are reported. The spectral growth of these expanding flames were recorded with a time resolution of 1 msec in the spectral range of 1.7 to 5.0 µm. Time-resolved spectra were obtained for methane-air mixtures as a function of stoichiometry, nitrogen dilution, and Halon dilution, in a 9-liter vessel under different venting conditions. Data are also presented for coal dust-air explosions. Temperatures, obtained from the absolute radiances and from a band ratio technique for methane-air, are internally consistent and are generally 50° to 200°K below adiabatic flame temperatures. All near limit mixtures gave essentially the same flame temperatures (1,500° to 1,600° K) regardless of whether the limit was obtained by dilution with excess air, excess methane, excess nitrogen, or Halon. The coal dust explosion spectrum is essentially a blackbody continuum at 1,500° K with some selective emission at 4.4 µm from hotter CO2. The data are analyzed in terms of the radiative dynamics of a sperically expanding flame zone. The importance of radiative transport is assessed. An equation is derived which relates the instantaneous fraction of combustion power radiated to adiabatic variables.

Jan 1, 1973

By S. W. Swerson

25.1-THE PURCHASING FUNCTION The word "purchase" means "to obtain by paying money or its equivalent; to buy for a price." This definition is all too simple to properly describe the word "purchase." One should consider the basic objectives of purchasing-to procure the right material, of the right quality, in the right quantity, at the right time, from the right source at the right price. Here it should be noted that in purchasing it is recognized that the best quality or grade of materials may be the only grade to purchase for a specific job. However. there are other jobs where the medium, standard or poor grade of materials is the right quality, as the lesser grade will perform adequately. In some companies the purchasing department makes the decision as to the right quality, while in others this function is shared with other departments. Years ago in business the owners controlled the purchase of required materials and services by performing the task themselves. The owners obtained the type materials and services they needed and paid the price demanded. This function was performed along with all the other duties requisite to the owner of a business, namely, clerical, hiring and firing of personnel, financial management, etc. As companies grew in size, clerical duties were assigned to other personnel and the owner usually retained the purchasing authority. This same division exists today in many small companies. However, in the larger companies, the purchasing function has been assigned to a separate department. Importance of the Purchasing Function-The larger the company the greater the need for a separate department to perform the purchasing function. Today the purchasing agent for most larger progressive companies has policy-making authority. Therefore, it is reasonable for him to report to the president or vice president of his company. Studies of several hundred companies show the purchasing department head reporting to top management 87.5% of the time. This fact in itself is indicative of the importance of recognizing that effective purchasing requires a department staffed with specialists in the field of procurement with knowledge and experience sufficient to perform in today's complicated business atmosphere. In the manufacturing field it is a common axiom that usually half of the company's dollar expenditures are for materials. If a purchasing department functions properly and the right product or service is purchased and a savings accomplished, the contribution to the net profit of the company is much greater, as opposed to sale dollars, where only a small portion is carried forward to net profit. Thus, the importance of the purchasing department and the contribution it can make to the success of the company are obvious. 25.1.1-THE PURCHASING FUNCTION 1. Responsibilities of the Purchasing Function-The purchasing agent in performing his function is acting as an agent for the company and others in the company requiring materials and services. Accordingly, he is committing the company for materials and services subject to certain limitations which the board of directors may stipulate. In view of this, the purchasing agent,'^ position must of necessity he

Jan 1, 1973

By C. W. Reno

"THE LORNEX MINING PROJECT is one of several large-tonnage, low-grade operations recently placed in operation in British Columbia. It is located in the Highland Valley in the south central portion of the province. This area is described as a divide valley at an elevation range of 4,000 to 6,000 feet and is situated on the divide between two drainage systems. The major drainage to the west flows into the Thompson River and to the east and south the drainage enters the Nicola River system. This open-ended valley lies between low, rounded mountains in fairly heavily-wooded country. Prior to the commencement of copper mining activities, the first by Bethlehem Copper Corporation Ltd. over ten years ago, the valley was only sparsely settled. A few small ranches were in existence on the several Indian Reserves located along the valley bottomland. There has also been a small amount of logging activity in the valley, although much of the area is covered by dense lodgepole pine which has little or no value to the loggers. As the mining interest mounted with further discoveries of the disseminated copper ore typical of the district, much of the valley was covered with mineral claims and exploration drilling was carried on by several companies at various times. At the time Lornex was preparing to commence major construction work in early 1970, there was very little activity of any kind in the Highland Valley outside of the Bethlehem operation and a small amount of ranching."

Jan 1, 1973

By J. E. Miller

The development of a new means of measuring the relative abrasivity of a slurry came about by necessity in 1967 during a full scale loop test of a 560 H.P. reciprocating pump handling magnetite slurry. In order to evaluate the life of expendable fluid end parts, the question of the amount of attrition in a re-circulated slurry had to be considered. An expected reduction in abrasivity as a result of this attrition would certainly give erroneous data on a parts life test. There- fore, some means of measuring such change in abrasivity became imperative. Several test methods were investigated1 but it was felt that these did not fully represent the wear due to back and forth rubbing action associated with a reciprocating pump. A "rubbing block" device used some years ago to determine the quality of hard facing materials was recalled, along with its shortcomings, in that an attempt was made to suspend a small percentage of abrasive particles in a colloidal viscous "mud". Erratic results were attributed to the fact that it was difficult to maintain a consistent slurry concentration under the metal wear block and the reciprocating speed was not great enough to maintain good agitation.

Jan 1, 1973

By Fred S. Karn

Inhibitors are used in coal mines as a precaution against accidental dust explosions. Although rock dust is the usual inhibitor many others have been tested. To facilitate testing a screening process using laser irradiation was proposed. The procedure includes irradiation of a coal-dust mixture followed by mass-spectrometric analysis of the evolved gases and an evaluation of the flammability characteristics of the gases. Carbonate-type inhibitors decreased the percentage of combustibles in the gases generated and inhibitors like NaCI (thermally stable salts) decreased the total gas generated. A suitable test procedure did not result from the investigation, demonstrating the inadequacy of fast heating, non-combustive techniques in rating inhibitors of coal dust explosions.

Jan 1, 1973

By L. C. DeCory

"Concrete is a common denominator to the building process and portland cement is an integral and necessary component of concrete. The cost of portland cement is nominal and its cost comprises, in most instances, a small portion of the total cost of ""put-in-place"" concrete.The domestic demand for portland cement in Canada is projected to be slightly less than 11 million short tons in 1980. In order to achieve this projected goal, stabilization or lowering of the cost of put-in-place construction is necessary. This enhancement of the cost of building can be achieved by:(1) improving the building process;(2) refining and improving design techniques; and(3) developing improved and economical concrete products.Some of the techniques and materials that will lead to building cost stabilization include systems building in its broadest sense, slipforming, precasting, prestressing, computer design, lightweight aggregates, fibrous concrete and integration of building components."

Jan 1, 1973

By Richard L. Ash

Introduction The blasting capabilities of commercial explosives are often rated according to their loading densities and detonation velocities. Both the density and velocity are relatively easily measured, the values of which can be used for determining the approximate detonation pressure developed by an explosive during any given set of blasting conditions (1-5). Knowledge of the actual rate of detonation attained at all points along a charger's length also is considered to give a good indication of how well the explosive is functioning. Many factors affect the density and velocity and have been thoroughly discussed by various authors (4, 6-12). For recording velocities several methods are available, but the resistance-wire, or probe, continuously recording technique has the distinct advantage of providing a record of the complete progress of an explosive reaction from the time it first initiates. Figure 1 is a copy of a typical record obtained by the procedure with certain significant information indicated. The theory and applications of the method are extensively covered in the literature so need not be reviewed for this report (13-18). Only the specific equipment and procedure employed for this investigation are presented.

Jan 1, 1973

By Kirk Carlton

This paper deals with a group of subjects so familiar to all of us that we might question the need for discussion. Even so, nearly every day's business turns up expensive examples of differences in understanding, misdirected assumptions and incomplete technical purchase documents. As our international activities increase, so do these problem areas. Their expense in both money and embarrassment gives rise to this attempt to focus a little extra attention on technical criteria and specifications. The two terms ?criteria? and "specifications" are, we believe, worth separating with respect to meaning. They should not be used interchangeably, although they often are. Criteria are by definition "standards for judging", whereas specifications are "enumerations of particulars". In relation to plant or project engineering, the criteria are the general rules and data which apply to the whole project and the specifications are the further listing of detailed requirements for specific contractual items or pieces of equipment. We'll look a little more closely at specifications after we give another minute or two to this "criteria" subject,

Jan 1, 1973

By J. Ribovich

The current Bureau of Mines active list of permissible explosives includes 71 brands. Eleven are gelatinous, 56 are the granular type, and four are water-gel explosives, an entirely new type of ammonium nitrate-based explosive for use in coal mines. The list of permissible blasting devices comprises five Cardox models.

Jan 1, 1973

By D. C. Downing

"I THANK YOU for the invitation which The Mining Society of Nova Scotia extended, originally to Gordon Berry, manager 'of our Point Tupper Refinery, to join you at this meeting and discuss refining and petrochemicals in their relation to this region. There are natural advantages in Nova Scotia which have made possible, and will continue to make possible, sizeable developments both in petroleum refining and in chemicals. Equally, however, as is the case everywhere, there are certain constraints. For clarity in this presentation, I will state some of these constraints right at the beginning. First, of any future developments from now on, only a small proportion of the products can be expected to go into local markets. I can make the point best with a few figures. Petroleum companies all have market forecasts. None ever work out to be perfect, but the trends are relatively predictable and the orders of magnitude are certainly correct. Estimates for the use of all refined petroleum products in the four Atlantic provinces are:"

Jan 1, 1973

By D. A. Doughty

The Bureau of Mines developed two methods for determining iron II and iron III in 2- to 5-mg samples of coal using electron paramagnetic resonance (EPR) spectrometry. One method used solid coal samples; the other method used aqueous solutions. The method using solid samples was more simple, technically, but required the use of X-ray fluorescent analysis, or another independent method, for determining total iron in the samples, and the results were subject to some uncertainty. The method using aqueous solutions appeared capable of greater certainty and did not require additional methods of total iron analysis but was more involved procedurally. The coals analyzed were found to contain much more iron II than iron III.

Jan 1, 1973

By Robert I. Fujimoto

The work described was conducted to develop standards for the application of wire rope clips on wire rope. These standards include optimum number of clips and clip nut torques for wire rope sizes 1/4 through 2-1/4 inches, when used for forming an eye attachment in wire rope. Wire rope test specimens with clip attachments were load tested on tensile testing machines to determine an effective combination of clip nut torques and number of clips for each size of wire rope to develop efficiencies above 90 percent of the catalog ultimate rope strength.

Jan 1, 1973

By L. G. Austin, P. T. Luckie

The Bond Work Index has been used for many years to estimate the power requirement of a material with known work index. The index is determined by a completely empirical test and no logical base for its use has been formulated. However, consideration of grinding as a unit operation which can be mathematically treated offers the prospect of considerably more accurate design and mill power estimation when sufficient data on large-scale mills becomes available. The interrelation of the Bond type with the unit operation approach is discussed.

Jan 1, 1973

By Eric B. Sansone

The Federal Coal Mine Health and Safety Act of 1969 requires coal mine operators to sample accurately the amount of respirable dust in the mine atmosphere. A technique approved for such sampling employs a 10 mm nylon cyclone followed by a membrane filter (nominal pore size ????= 5 µm) and a pump. The pump is required to provide a flow rate of 2.0 ± 0.1 liters per minute. Calibrations have yielded a range of flow rates (1.4 to 2.8 1pm) at which the cyclone should be operated to remove the non-respirable portion of the dust. The purpose of this project was to evaluate the performance of the 10 mm nylon cyclone at flow rates of 1.8 and 2.0 1pm using a polydisperse coal dust aerosol. The penetration characteristics of the cyclone were to be compared to the United States Atomic Energy Commission's respirable dust standard. The effect of relative humidity on cyclone penetration characteristics was also to be observed.

Jan 1, 1973

By H. U. Ross

"INTRODUCTION Extensive studies have been carried on pure gold to determine the various factors that affect its dissolution in alkaline cyanide solutions. With the extension of milling to refractory ores more intensive investigations on the effect of impurities in the ore on the dissolution kinetics are needed. The present work describes experiments carried on refractory flotation tailings with the object to determine how the recovery of gold could be increased. The effect of arsenic and antimony in the ore and the excessive use of lime are discussed. Control of cyanide losses is also dealt with.MECHANISM OF THE GOLD DISSOLUTION REACTION In aqueous cyanide solutions, gold is believed to be dissolved by one of the following reactions:4Au + 8NaCN + O2 + 2H20 = 4NaAu (CN)2 + 4NaOH (1)2Au + 4NaCN + 2 + 2H20 = 2NaAu (CN)2 + 2NaOH + H202 (2)2Au + 4NaCN + H202 = 2NaAu (CN)2 + 2NaOH (3) The first of these, known as the Elsner Equation is supported by )4 3,2,1(several authors while others(5,6) support reactions 2 and 3 known as the Bodlander Equations. According to Habashi(7), the overall reaction for the dissolution process is as shown in equation 2. Most of the workers agree that hydrogen peroxide is produced in the course of the reaction."

Jan 1, 1973