Search Documents

By Richard E. Thill

Elastic wave velocities and moduli were determined by both the pulse and resonance methods in a large number of specimens of St. Cloud Gray Granodiorite and Tennessee marble under the same moisture, temperature, and stress environment. Long cylinders were first tested by the resonance method to obtain longitudinal bar and torsional wave velocity. The cylinders were then sectioned in half and tested by the pulse method to obtain the transient pulse velocity. These velocities were later used to obtain various moduli for comparison. Statistical comparisons between the Young's, shear, and bulk moduli and Poisson's ratios obtained independently by the pulse and resonance methods indicate that the methods do not give equivalent results in nearly isotropic rock. The amount of difference varies for each modulus, with the least difference (less than 5 pct) occurring in the shear modulus and the greatest difference (as high as 34 pct) in the bulk modulus. Moduli determinations in aluminum show much closer agreement between the pulse and resonance methods than in rock. The discrepancy in pulse and resonance results probably is caused by frequency dispersion effects and by differences in error sensitivity in the various formulas used to calculate the moduli.

Jan 1, 1974

By C. B. Manula, R. L. Sanford, R. A. Rivell

PART I. FLOW CHARTS

Jan 1, 1974

By Maurice Deul

Certain health and safety hazards occur entirely unexpectedly in some subterranean excavations. Although ground support is not the subject of this paper, ground failure can result in large and often uncontrolled flow of fluids into an excavation. Even when there is no ground failure, the disturbance of nature's equilibrium between rock or unconsolidated alluvium or rubble and the contained fluids poses severe problems to a well planned operation. Optimum conditions for safe operation cannot be the sole criterion for site selection. Some mineral deposits form in zones of structural weakness, others form where hydrothermal alteration substantially weakens the enclosing rock, and tabular deposits such as coal and evaporites inevitably undermine large areas. Excavation to acquire mineral values cannot be relocated. The same is often true for tunnels driven to connect distant points by the most direct route. Rivers and mountains cannot he avoided, and the cost of lengthening a tunnel--by even a fraction of a percent--must be strongly justified. No responsible engineer will knowingly select a dangerous route for excavation, but to what extent do engineers attempt to assess the health and safety hazards that may be reasonably expected? How, specifically, can methane explosions, water and sand flooding, dangerous dusts, toxic gases, thermal shock and radar poisoning be eliminated or minimized through systematic advance planning?

Jan 1, 1974

By S. F. Hillis, J. E. Rourke, K. A. Szalay, O&apos

INTRODUCTION For the past 25 years, tunnel support requirements have frequently been determined, at least in North American practice, by classifying the rock according to the system proposed by Terzaghi (1), using one or more of the 8 Rock Conditions which he defined, the rock load then being selected within the range given for each Condition. However, there is a lack of published data comparing Terzaghi loads with actual measured rock loads, and it would appear that the degree of conservatism, or otherwise, of the Terzaghi approach is very often unknown. Excavation of 4 large diameter tunnels at the Tarbela Dam Project in Pakistan afforded an opportunity to compare Terzaghi and measured loads, through instrumentation of the steel ribs installed for temporary support, and by classification of the geology exposed during the tunnelling operations. In addition, the deformation of the rock surrounding the tunnels was monitored during excavation by means of borehole extensometers installed prior to the start of tunnelling. This paper describes the tunnel instrumentation and the results obtained therefrom, and relates these results to the Terzaghi load coefficients. It also discusses the effects of the methods of excavating the tunnels on the rock loads and rock deformations. PROJECT DESCRIPTION The Tarbela Dam Project is located on the Indus River in

Jan 1, 1974

By Clark K. N

The need for and advantages of simulators in iron ore pellet induration research are described. The approaches to simulation and the techniques to carry it out are discussed in detail covering drying and firing for the straight grate process. The CSIRO simulator design is described and some errors in simulation are discussed.

Jan 1, 1974

By Bernard Lippe

The successful construction project is one in which the component construction operations are completed within the scheduled time and cost parameters. Most construction projects, however, are subject to delays and/or disruptions which adversely affect the time (start, duration, and completion) and cost aspects of the project. DELAYS Delays fall into two categories: Compensable Delays for which the contractor is entitled to contract time extensions and additional money as compensation for the extra expenses generated by the delay or obstruction to job progress, and Non Compensable Delays, for which the contractor may or may not receive an extension of time but no additional compensation. Compensable Delays Compensable delays may take the form of holds or suspensions on all or certain segments of a project by the owner, failure of the owner or his Engineers to approve shop drawings, cuts or material samples within a reasonable period of time, failure of the Owner or his Engineer to properly coordinate the job, discovery of design deficiencies in the plans and specifications which prevent the continuation of construction until

Jan 1, 1974

By Parviz F. Rad

The Bureau of Mines conducted rock-cutting experiments under constant normal force and constant penetration in an effort to correlate laboratory data with those obtained in the field. Both independent and interacting groove spacing regions were studied, and optimum and critical cutter spacings were determined. For the laboratory work, the effects of specific energy, muck weight, groove depth, cutting coefficient, and size distribution of the muck for both independent and interacting grooves were studied. For field operations, forward thrust, torque, advance rate, and muck size distribution were the parameters studied. Satisfactory correlation is obtained between laboratory cutting results and field performance data.

Jan 1, 1974

By L. J. Lindsay

Kaiser Resources Ltd. operates a coal mining complex in Southeastern British Columbia. A large surface mine, a conventional underground mine, and an innovative hydraulic underground mine are presently in operation. The products of these mines are fed to the Elkview plant. This coal has to be prepared to 9. 5% ash and 6'o total moisture for export from the port of Roberts Bank near Vancouver, British Columbia to Japan at a rate of 4. 5 Mltpy. The moisture requirement for the coal product was recently increased to 8. 0% total moisture. The entire operation has been described in various publications (1), (2), (3). Details of the venture will not be repeated in this paper. In this paper we hope to describe the modifications made to the original coal preparation plant in order to satisfy market requirements for quality and quantity of coal.

Jan 1, 1974

By Lloyd A. Morley

Previous research conducted for the USBM by Penn State personnel (Grant GO-101729) found that a need existed to physically model a typical a-c/d-c coal mine section electrical system. Its purpose would be to permit preliminary evaluations of electrical problem solutions prior to launching full-scale investigations. Such use can result in greater flexibility than afforded by present computer models. Furthermore, numerous problems, which would be virtually impossible to incorporate in a computer model at this time, are more easily analyzed with physical simulation. The development of this system is now proceeding at the USBM's Bruceton Research Facilities. However, electrical specifications of scaled down components for its construction are required. This project is a result of that need and has been funded as an extension to Grant GO-133077. The following report covers these specifications. Scope of Work To represent a mined a-c/d-r. coal mine section, the typical component specifications must detail at least: a. one a-c continuous miner, b. two a-c or d-c shuttle cars, c. one a-c or d-c roof bolter, d. one a-c section fan, and e. feeder cables. Further, each machine should be portrayed by each of its general

Jan 1, 1974

By Bowling K. McG, Hamilton J. D G

The influence of three important para- meters which affect the induration of iron-ore pellets, viz temperature, time, and lime content, have been assessed in terms of internal pellet structure and commonly-used pellet quality criteria. The pellets studied were produced from a typical hematite ore from the Pilbara area of Western Australia, using a 25 cm dia. pot-grate test rig. Isothermal laboratory induration tests were conducted in accordance with a statistically-planned programme. The internal structures were studied by optical microscopic examination of polished sections of the test pellets. The effects of SFCA (silico- ferrite of calcium and aluminium) and slag formation, matrix consolidation and grain modi- fications were studied, and have been related to pellet properties and to the time/temperature histories produced by the firing conditions chosen. The implications of the data for commercial pellet plant operations are discussed.

Jan 1, 1974

Since 1865 when Congress moved to create a Federal Mining Bureau, successive legislations have given rise to the current '!Federal Coal Mine Health and Safety Act, 1969. Coal beds from 22 feet to 20 feet thick are mined under covers from 50 to 2800 feet with full and partial pillar recovery equally popular and accounting for a total of 54% of the mines. Pillar recovery and roof support practices vary, and each operator must submit an overall roof control plan (within specific guidelines) for approval before undertaking any development. The guidelines relate to dimensions of openings, details of support, sequence of extraction, limits of extraction and caving details. Experienced and professional staff of M.E.S.A. provide roof control plans and make inspections and grant-approvals of principles of support and minimum support in pillar extraction, with provision for modifications with time. Guidance is given with training programmes and standards of supervision. All of these aspects are approached in the spirit of the Congress declaration that the first priority and concern must be the health and safety of the miner.

Jan 1, 1974

By Thulin D

In 1971 the first Grangcold Pelletizing Plant came into operation at Grangesberg, Sweden where from a rich magnetite low- phosphoric concentrate and a cement binder (Portland cement clinker and granulated blast furnace slag) self-fluxing blast furnace pellets are produced.

Jan 1, 1974

By Howard J. Pincus

The purpose of the study is to investigate the effects of fracture fillings and associated alteration on the mechanical behavior of rocks. Experimental results are presented for 98 specimens from the Climax mine, which were tested since the annual report (May 1973). The conclusions reached are based on both these results and those reported in the annual report. The locations studied are the Climax and Henderson mines in Colorado and the San Manuel mine in Arizona. The rock types studied from each location are from: 1) Climax, medium-grained granite, fine-grained granite, granite porphyry, schist, and gneiss; 2) Henderson, rhyolite porphyry; 3) San Manuel, quartz monzonite and quartz monzonite porphyry. A description of the rocks was made including: color, texture, mineralogy, composition and fabric of fracture fillings, density, apparent porosity, and optical diffraction patterns. Unconfined and triaxial compression tests were run on the Climax and San Manuel specimens. Sonic velocities were measured during the compression tests; Shore sceleroscope hardness was measured before the compression tests. Conclusions are that some relation appears to exist between compressive strength and the following properties and features for all specimens: dynamic Young's modulus, sonic velocity, density, rock composition, slope of velocity curve, composition and fabric of fracture fillings-veinlets, and apparent porosity. There appears to be some relation between compressive strength and Shore scelerscope hardness for the quartz monzonite (San Manuel). A relation appears to exist between texture and compressive strength and the extent of failure on fracture fillings for schists, gneiss, and fine-grained granite (Climax). The amount of swelling clays (montmorillonite, hydromicas, etc.) present in the rock and the relative number of fractures in which they constitute of major portion of the fracture fillings are related to the strength of the rocks. Possible tests for checking the amount of these clays present is presented including saturation, dyes, and X-rays. A useful index relating to rock strength, as revealed in this study, is the presence of swelling clays in detectable abundances. These clays can be detected in the field with a simple wetting and striking test; in the laboratory they can be detected by X-ray and dye methods.

Jan 1, 1974

By C. P. Siess, S. L. Paul, E. H. Gaylord

Several types of tunnel supports are being investigated experimentally and analytically at the University of Illinois at Urbana-Champaign under the sponsorship of the Federal Railroad Administration, Department of Transportation. The results of work on two types will be discussed here. These are steel sets and continuous, monolithic steel-fiber-reinforced concrete liners. The latter is a model of a short length of liner that might result from a continuous slip-forming operation in a tunnel excavated with a boring machine. Tests have been performed on both types of support and analyses are being developed which will greatly broaden the scope of the test program. The objective of these studies is to improve the understanding of basic behavior of these supports, and to develop techniques for their analysis. The analyses will then be used to perform parameter studies that will lead to more rational procedures for structural design. The tests provide a check on the accuracy of the analysis and demonstrate the overall behavior and modes of failure. Another part of the project is concerned with the interaction of support and medium, and thus prediction of loads for the supports. These studies are presented in greater detail in a recent report (1). A brief outline of results obtained to date are presented in this paper. STUDIES OF STEEL SETS Description of Set Tests The sets tested were of the horseshoe type with a 5-ft radius arch section and 7-ft straight legs. They had bolted joints at the crown

Jan 1, 1974

By F. S. Knoll

The high tension process which separates materials based on relative differences in surface conductivity has been very successful in recovering non-ferrous metals from municipal waste. Aluminum is by far the largest constitutent of the total non-ferrous metal fraction; accounting for >95% in most localities. Wire and insulation mixtures from industrial wastes have been treated commercially for several years by a high tension process initially developed for use in the iron ore industry. The wire and insulation application was a forerunner of municipal waste dry treatment technology. In the past eighteen months the rotating-drum-type electrostatic separator has undergone extensive testing and development in order that the process might be efficiently adapted to the recovery of aluminum from municipal waste.

Jan 1, 1974

By Jackson M. Langton

Substantial evidence supports the theory that high-angle faults and overthrusts in the Morenci-Metcalf region were initially caused by a Late Precambrian-Early Paleozoic stress field. These faults were reactivated in Late Paleozoic-Early Mesozoic time which completed the structural framework prior to the Laramide Orogeny. Excluding an interruption by diabase dikes and sills, Paleocene-Eocene magmas invaded the pre-existing structures and became progressively more sialic in composition and nearer to the surface with each subsequent injection. The last sialic intrusion was highly explosive, rendering the country rocks more permeable for hypogene and supergene activity. Widespread dilation, instigated by uplift and subsequent magma intrusion, caused extension to the northwest and southeast. A major locus of hypo gene alteration and mineralization appears to be centered around the south and southeast periphery of the youngest granite porphyry stock. A potassic, sulfide-deficient core is telescoped by a pyritic, phyllic zone which in turn is enveloped by widespread propylitic alteration.

Jan 1, 1974

By Henry J. Jacoby

This report concerns Contract No. 3B of the Port Richmond Project, for the Department of Water Resources of the City of New York. It involves the construction of 7, 000 ft. of 7 ft. finish I. D. interceptor sewer by tunneling in soft ground, as well as associated manholes, regulator chambers, siphons and miscellaneous sewers and structures, beneath a heavily travelled perimeter road in Staten Island. The Contractor is Richmond Constructors, a joint venture of Grow Tunneling Corp., sponsor, MacLean Grove & Company, Incorporated, Morrison-Knudsen Company, Inc., and Andrew Catapano Co., Inc. Project manager is Paul DeMarco, Vice-President of Grow Tunneling Corp. The cortract, as designed and bid, requires the use of liner plates 101 -0" O. D., and both cast iron and steel designs of several widths were included in the bid documents by the owner. The specifications also required the contractor to install and put into operating condition, prior to commencement of mining, a complete low pressure compressed air plant and all accessories for mining in compressed air, even though the contractor was given the option of using other methods of ground water control. A third requirement of the specifications was that a shield be used, either manual or mechanical, and with full provision for "breasting". BACKGROUND The first soft ground shield driven tunnel in the United States was in New York City and was built under Broadway in lower Manhattan in 1869

Jan 1, 1974

Increasing use has been made of engineer ing geology and hydrogeology in the development of the infrastructure for mining projects. The Geological Survey of the Department of Mines, the Department of Main Roads, the Irrigation and Water Supply Commission and private consulting organisations and mining companies, employ spec- ialist staff to carry out engineering geological and/or hydrogeological investigations. Such in- vestigations have been of assistance in recent mining developments in northern Queensland, in- cluding those in the Cloncurry - Mount lsa, Weipa, Greenvale and northern Borten Basin areas.

Jan 1, 1974

By Laurance L. Oden

The Bureau of Mines is developing melting data for binary combinations of the alkaline earth fluorides and yttria to facilitate the formulation of slag compositions. The present report deals with the SrF2-Y2O3 system for which liquidus and solidus temperatures and solid solubilities were determined. The information is presented as the phase diagram. The phase diagram was constructed from information obtained by ceramogra¬phy, X-ray diffraction, thermal analysis, and electron probe microanalysis of small specimens encapsulated in platinum-20 percent rhodium or molybdenum ampoules. The data indicate a simple eutectic system with limited terminal solid solubilities. The eutectic temperature is 1,457°±5° C, and the eutectic composition is 4±1 mole-pct Y203. Strontium fluoride containing up to 2 wt-pct 0 2 was studied to determine the effects of oxygen contamination. Oxygen levels in excess of 0.2 wt-pct resulted in eutectic formation between SrF2 and SrO. The eutectic composition is between 0.2 and 0.7 wt-pct 02, and the eutectic temperature is 1,447°±5° C. No intermediate oxyfluoride phases were detected.

Jan 1, 1974

By AIME

The following corrections (in italics and bold face) were received too late for the September issue of Transactions: Page 270, Abstract, line 1, spelling should be goethite. Page 270, column 1, authors' box, authors' affiliations should read: L. A. BAKER, formerly Principal Research Scientist, is Pellet Plant Superintendent, Cliffs Western Australian Mining, Cape Lambert, W. A., Australia. C. G. THOMAS is Experimental Officer, Minerals Research Laboratories, C.S.I.R.O., North Ryde, N.S.W., Australia. R. J. CORNELIUS and K. S. LYNCH are General Superintendent, Product and Process Development, and Superintendent, Pellet Plant, respectively, Hamersley Iron Pty. Ltd., Dampier, W. A., Australia. G. J. ARMSTRONG, formerly Chief Metallurgist, Hamersley Iron Pty. Ltd., is Mill Superintendent, Samin Ltd., Burra, S. A., Australia. Page 271, column 2, line 41, should read "highest possible spalling temperature and to adjust the. . :' Page 275, column 1, line 1, should read "(LOI) figures are shown in Table 1 and vary from 2.61..." Page 275, column 1, line 16, spelling should be goethite. Page 276, column 2, line 6, should read "Predicting Grate Speed and Production Rate: The cor-..." Page 276, column 2, line 8, should read "basis of Blends A, B, C, D, and Plant Ore 1, shown in Table..." Page 276, Table 3, heading under "Prediction Method" should read Blend E. Page 277, column 1, line 38, should read "=293 tph of specification pellets (see Table 1 for loss-..." Page 277, column 2, replace caption for Fig. 14 with the following: Fig. 14-Example of calculation of hood temperature profile during downdraft free-water drying, given plant free-water drying time. Page 277, column 2, replace caption for Fig. 15 with the following: Fig. 15-Example of calculation of hood temperature profile during drying, given plant goethite drying time.

Jan 1, 1974