Search Documents

The mineral chromate is the sole current source of commercial chromium Chromite varies compositionally within limits permitted by the formula ((Mg,Fe,Zn,Mn)(A1,Cr)2O4) No chromate has been mined in the United States since 1961 In the past, almost all the chromate mined in the United States came from Alaska, California, Maryland, Montana, Oregon, and Pennsylvania, with about one-half of all production coming from Montana Primary chromate deposits occur only in certain kinds of ultramafic or closely related anorthositic rocks The two major types are stratiform (layered) and pod-shaped The Stillwater Complex of Montana is the largest known United States resource It is a stratiform deposit where several exposed zones of high-iron chromiferous material extend in length Since there is no commercial chromate mining in the United States, there are no environmental problems related to underground mining

Jan 1, 1975

By Robert G. Bottge

Hard rock mining has grown in importance in the Yukon Territory during the last 10 years while Alaskan hard rock mining has declined. One asbestos deposit in Alaska is dormant, but an asbestos deposit 55 miles to the east in the Yukon Territory is being mined by the Clinton Mine Div., Cassiar Asbestos Corp., Ltd. In this Bureau of Mines report, the economics of mining in the two locations were derived using the Clinton mine as a model. Both deposits were assumed to be of equal size and mined by similar methods. Conventional open pit mining and processing methods were assumed, and capital and operating costs were derived using flowsheets and standard costing methods. The estimated cost for the mine, mill, and support facilities in Alaska was about 30 percent more expensive than that in the Yukon Territory. The higher labor rates in Alaska were the primary contributor to the higher construction costs; freight rates added only slightly to the total costs. Approximately two-thirds of the additional annual costs of operating in Alaska were for wages and fringe benefits. The price required for the Alaskan asbestos fiber was $356.65 per ton compared with $287.44 for Yukon fiber, plus or minus 20 percent. A 12 percent discounted cash flow rate of return, 100 percent equity financing, and a rapid writeoff of assets were assumed.

Jan 1, 1975

By Charles W. Trettel

Confined explosives upon detonation produce a chemical reaction generating expanding gases that result in fragmentation of matrix a chemical to mechanical transition. A 100% energy conversion during transition is difficult, if not impossible, to achieve. There are numerous variables that affect energy transition. Although fragmentation is the most often used criteria to determine shot efficiency, the escaping energy profile provides additional data as to the efficiency of a blast. Escaping energy can also have deleterious effects in the form of ground motion.

Jan 1, 1975

By Robert B. Crookston

Oil from shale has been produced in foreign countries for more than a hundred years; however, except for short-lived, small operations, no commercial quantity of oil shale has yet been produced in the United States. Efforts to develop a viable oil shale process have been underway domestically for many years. At the present time, with the need for energy so urgently upon us, almost a dozen development ventures are underway or planned in Colorado and Utah. Of these several ventures, only Colony Development Operation has completed the development, testing and design of a ready-to-go 50,000 barrel per day com¬mercial project. Colony is a joint venture of the Atlantic Richfield Company, Ashland Oil Company, Shell Oil Company and The Oil Shale Corporation, more commonly known as TOSCO. TOSCO is the exclusive licensor of the TOSCO II retorting process and other oil shale technology, which includes mining, crushing and spent shale disposal techniques. This paper will deal, however, with only the materials handling aspects of the commercial oil shale operation. Oil shale handling for this infant industry is unique in that an understanding of the physical characteristics of the ore and the demands on material handling to the plant must he understood. Colony Development has completed ten years in the research and development of techniques and processes for mining, crushing and retorting raw oil shale and the disposal of spent or processed shale. A great deal has been learned about oil shale, in many cases confirming our intuitive analyses and the work of others, but more specifically we have brought it all together to a point where equipment performance and the specifications have been established and a design for the first commercial plant is now mature.

Jan 1, 1975

By W. T. Westbrook

This Bureau of Mines report contains methods for analyzing iron are for total iron, ferrous iron, metallic iron, silica, manganese, aluminum, calcium, magnesium, phosphorus, titanium, carbon, sulfur, moisture loss, and ignition loss by wet chemical methods. Some are modifications of standard umpire methods; others have been developed by the Bureau of Mines to provide a com-bination of speed and accuracy. They are suitable for a high volume of samples and/or control situations, and for situations in which instrumental results must be verified. These methods have been used to analyze taconites, native ores, some foreign ores, and metallurgical products.

Jan 1, 1975

By Trudinger JP

Mt. Newman Mining Company Pty. Ltd.3 oper ates the Mt. Whaleback iron ore mine in the Ham- ersley Iron Ore Province of Western Australia. The present rate of production of high grade hematite iron ore is 33 million tonnes per year. Mining is by open cut quarrying,with 15m high benches. The present quarry operations will be extended to a large oval pit to win over 1400 million tonnes of iron ore. The pit slopes will extend up to 500m in depth and the perimet- er of the slopes will exceed 15km. Sixty per- cent of the ore is below the water table, which presently lies 45m below the general plain level Dames & Moore, rock mechanics consultants designed the pit slopes during early mine devel- opment to ensure an economic and safe operation.

Jan 1, 1975

By S. L. Crouch

The application of a simple, two-dimensional computer technique for evaluating rock burst potential in cut-and-fill stopes was investigated. The principal purpose of the study was to compare the effectiveness of high-modulus fill and destressing as aids in the control of rock bursts. Two conclusions that are probably of general applicability are drawn. First, high-modulus fill is ineffective as a means of increasing the mine stiffness and acts to control rock bursts only if it supports enough load to reduce substantially the stresses on the unmined vein material. Second, destressing is most effective if it is performed when the vein material is near the point of failure.

Jan 1, 1975

By Donald I. Kurth

The Bureau of Mines conducted experimental work on comminuting coal. The size distributions of coarse fragments and fine particles were obtained under different modes of energy application--drop, impact crushing, wedge impact, compression, and shear tests. Four levels of energy application were used in the impact crushing and wedge impact tests. Airborne dust and respirable air-borne dust distributions were obtained for the impact crushing and wedge impact tests. Analyses of nonairborne dust and coarse fragment-fine particle distributions were carried out on impact, wedge, compression, and shear tests. The experimental size data on nonairborne dust were fitted to normal, log-normal, power law, Weibull, log-Weibull, and exponential distribution functions. Both the nonairborne dust and the coarse fragment-fine particle size distributions are best described by Weibull distributions. For the impact crushing tests, mean product size was found to be inversely related to specific crushing energy. The particle counts in a given size range of airborne and nonairborne dust were found to increase with increased input energy and specific crushing energy. However, in another sense the particle distributions were independent of energy level; that is, the percent-ages in a given size range were approximately constant regardless of energy level. Respirable airborne dust was related to respirable-size nonairborne dust by a power law.

Jan 1, 1975

By H. Billmayer

This report covers the period from June 17, 1974 to February 20, 1975, and describes the work performed in compliance with the requirements of Contract No. H0346102 and Modification No. 1 thereto. The purpose of the contract was to design protective canopies for an Elkhorn Scoop, a Lee Norse Miner, a Wilcox Miner and a Wilcox Bolter; to construct mockups of the canopies; and to obtain machine operator evaluations of the canopy designs by assessing the mockups while installed on their machines in the mines. The overall program objective was to achieve protective canopy designs for the four machines which would be acceptable to the operators.

Jan 1, 1975

By Robert L. Schuster, James A. Doolittle, Ronald L. Sack

The effect of the height of a retaining-wall-supported berm on the slope stability of an idealized mine-tailings dam was investigated. The material in the dam was idealized as a two-layered system with the phreatic surface delineating the boundary between the layers. In each layer the tailings were assumed to be homogeneous and isotropic. The effect of variation in height of the berm was examined for tailings dams with three different, commonly occurring slopes. The stresses and displacements were obtained using the finite element method. An incremental analysis technique was employed to simulate sequential construction of both the tailings dam and the retaining-wall-supported berm. A one-dimensional element was used to represent all interfaces and discontinuities in the finite element model. Assuming a hyperbolic model, the nonlinear stress-strain relationship for the tailings was approximated using the method of successive increments. The stresses obtained in the finite element analyses were used in conventional slope stability analyses assuming circular failure surfaces. The results of the study show that the use of a retaining-wall-supported berm is an effective means of improving the stability of a tailings dam. This increased stability is greater for dams with steeper slopes. In addition, the increase in factor of safety is particularly notable for berm heights less than 25% of the height of the dam.

Jan 1, 1975

During the presentation of the papers, questions were deferred until after the last paper in the afternoon. At that time, the authors and co-chairmen formed a panel for discussion of any pertinent questions. The panel was as follows: Carl Gerity - Ozark Lead Company – Chairman Mike Young - Master Mechanic - Ozark Lead Company Largo Albert - Maintenance Specialist (hoisting) Mines Maintenance Dept. - International Nickel Company, with assistance from Co-author Alan Cameron - International Nickel Company Gary Beerkircher - Product Manager - Rexnord Inc., Nordberg Machinery Group Richard Schaal - Director of Maintenance - Superior Division, Magma Copper Company Rich Hodgson - Assistant Production Superintendent - FMC Corporation The remarks have been edited by the panelists for readability, the basic ideas were not changed. Additional thoughts by the panelists submitted at the time of their revision are indicated by ***.

Jan 1, 1975

By Richard H. Spencer

Since the passage of the Coal Mine Health and Safety Act of 1969, the Bureau of Mines has made many advances in mine communications. These efforts have resulted in the following developments and demonstrations: Surface-to-surface electromagnetic transmission of baseband voice signals through overburdens as deep as 600 feet. This transmission was achieved with equipment from the Interim Mine Rescue and Survival System Program, and demonstrated that baseband voice communications could be obtained through these overburdens in the absence of mine-generated noise; that is, when the mine power system was shut off, However, during mine operational conditions, the mine-generated noise proved to be so large that effective baseband voice communications to the desired depths could not be effected.

Jan 1, 1975

By John Jan

Iodine is a soft, lustrous, grayish-black non- metallic element with a density of 4.9. It is the least active of the four members of the halogen family. The other members are, in order of increasing activity, bromine, chlorine, and fluorine. Iodine is a solid at ordinary temperatures, while bromine is a liquid and chlorine and fluorine are gases. Iodine melts at 113°C and volatilizes at 184.4°C to a blue- violet gas with an irritating odor. It occurs in nature only as iodates and iodides or other combined forms. It was discovered by Bernard Courtois in France in 1811, who noticed its presence as an unknown substance in crude soda ash obtained from burning seaweed. Gay-Lussac recognized it as a new element and named it iode, from the Greek word "ioeides or iodes" for violet color (MacMillan, 1970). The world production is not known with any great certainty, but it is probably between 20 and 25 million lb per year, of which about 25% is consumed in the United States. Geology and Mineralogy Iodine compounds occur as a minor constituent as a mineral in the Chilean nitrate deposits and in solution in brines and sea- water. According to the U.S. Geological Survey, it is the 47th most abundant element in the earth's crust. The minerals lautarite, Ca (10,) (calcium iodate), and dietzeite, Ca, (10,) , (CrO,) , (calcium iodate-chromate) are found in Chilean nitrate deposits which are located in Antofagasta and Tarapach provinces on the eastern slope of the coast range in a desert area. Various brines contain iodine compounds. Seawater contains about 0.05 ppm of iodine and some seaweeds will extract and accumulate it up to 0.45% on a dry basis. Some coals in West Germany also contain iodine compounds. The known and potential sources of iodine reported in 1968 are given in [Table 1]. Iodine has been recovered from brines in Java, Indonesia, France, England, and the USSR. Iodine has also been recovered from seaweed in Ireland, Scotland, France, Japan, Norway, and the USSR. The indicated re- serves and future resources of iodine are large but have never been adequately measured. Analysis Iodine as the free element can be detected by the characteristic blue color it gives to a starch solution. Quantitatively it is determined as the free element by titration with standard thiosulfate solutions using starch as an indicator. Colorimetric methods are also applicable.

Jan 1, 1975

By Jerome S. Brower

Quadrex-L is a two component liquid explosive which was developed by J. S. Brower & Associates, Inc. to facilitate handling and shipping, and use in unique applications, while emphasizing safety. It may be advantageously used for all explosive applications. Quadrex-L can be introduced into a preinstalled container configuration and may be easily drained or flushed from these containers when necessary to do so. This characteristic can be effectively utilized to reduce the hazard period during assembly or disassembly operations.

Jan 1, 1975

By Donald J. Moore

It has become more important today than ever before to reduce costs and improve equipment utilization. One area where such improvement can he achieved is in the use of explosives. Effective blast design for efficient use of explosives as well as optimum fragmentation can achieve this. Towards this end we must have available to us a practical design method in which experience and observation can be translated to engineering concepts. We must he able to communicate the design data to field blasting personnel as well as management in an understandable way.

Jan 1, 1975

By R. W. Winson

Asbestos is the generic name given to a group of fibrous mineral silicates found in nature. They are all incombustible and can be separated by mechanical means into fibers of various lengths and cross sections, but each differs in chemical composition from the others. The commercial grades of asbestos consist of a spectrum of lengths and sizes and are not definitive as are most organic fibers. It is generally recognized that there are two main groups of asbestos. The first only contains the fibrous serpentine called chrysotile and comprises about 94% of the world production of asbestos. The second group contains five minerals in the amphibole series+rocidolite, amosite, anthophyllite, tremolite, and actinolite. The latter two have no commercial importance. Properties Physical The structures of asbestos fibers have been studied intensively over a number of years. X-ray diffraction patterns have been used as a means of identification and classification. Low angle X-ray scattering techniques have shown that chrysotile fibers are "hexagonally close packed" and parallel to each other, having cross-sectional diameters varying from 18014 to 300A units, while the amphibole fibers are many times larger in cross section. Electron micrographs of the more common types of as- bestos are shown in [Figs. 1-4]. [Fig. 1] illustrates the softness and flexibility of chrysotile which make it suitable for textile-type products. For a number of years there was considerable controversy over the exact nature of chrysotile fiber, but the photographic evidence in [Figs. 5-7] clearly show that it is tubular in structure. The curvature is the result of the mismatch in the dimensions of the silica [Si,O,l and brucite [Mg(OH),] layers which are on the inside and outside, respectively, of a double sheet. This curvature had been predicted by Pauling (1930) years ago based on the molecular dimensions of the two component structures.

Jan 1, 1975

By Dawson RD

For the past 45 years, the casting of refined lead ingots by The Broken Hill Asso- ciated Smelters Pty. Ltd. (B.H.A,S,) at Port Pirie has been mainly by use of manually operated rotary casting wheels of Newnam design. This style of operation was quite satisfactory as far as standard of product was concerned, but was manually intensive and a relatively high cost operation. With most other large scale lead producers already using automated-casting equipment, an investigation which commenced in 1966, progressed through stages of enquiry, design and development until the present plant commenced trial operations in late 1973, and fully operative in late 1974. While certain features of the plant are sed on overseas practices the plant was signed and built within Australia to BRAS ecifications. As constructed it consists two almost identical casting lines each pable of producing 25 kg ingots at 25 tonnes r hour using straight line casting machines d automated stacking weighing and strapping

Jan 1, 1975

By John P. Cummings

Glass is the most unique substance which man has made. It is understood that Phoenician sailors playing on the beach in Mesopotanmia around 12000 BC, produced glass by the fusion of sand and soda in their campfire. Glass is unique for many reasons. However, let us consider the following. It is made of materials which are opaque and yet glass can be translucent, transparent, or opaque. It can be as soft as cotton or stronger than steel. It transmits light readily and yet is totally impervious to gases and liquids. It is chemically an inert, creates very little pollution in its manufacture. It is made of the most abundant raw materials on earth. It is readily recyclable and has little pollution in its disposal. Glass containers are made principally from sand (that is, silica), soda, which is sodium carbonate, and lime, which is calcium carbonate, plus decolorizers or colorants and cullet. The proportion of cullet, broken glass, in most glass tanks today is roughly 10 to 20% of the glass product. In most cases, the cullet used in the plant is glass from off-ware, or broken ware, which is a waste product within the plant. Cullet has the following advantages. It contains all of the raw materials normally used in a batch. It tends to melt at a lower temperature than batch, thus saving some fuel, and, finally, by forming a crust above the normal melting system, there is a tendency to cut down air pollution.

Jan 1, 1975

By Frank C. Appleyard

The two calcium sulfate minerals-gypsum and anhydrite-occur in many parts of the world, and gypsum has long been of economic importance in the family of industrial minerals. Gypsum, the dihydrate form of calcium sulfate (CaS042H20) and anhydrite, the anhydrous form (CaSO4) are frequently found in close association, and it is seldom that a calcium sulfate deposit will consist exclusively of one mineral or the other. Although known gypsum deposits are extensive, anhydrite makes up the largest part of total calcium sulfate reserves. However, it has very minor economic use, and most of the following discussion will be devoted to gypsum. Calcium sulfate is one of the principal con- stituents of evaporite deposits, and when pure, has the following composition: [ ] Deposits of pure gypsum or of pure anhydrite which are large enough to be considered commercial have never been found because of both the metastable relationship between the two minerals, and the presence of impurities such as calcium or magnesium carbonates, chlorides, other sulfate minerals, clay minerals, or silica. As a result most mine production of gypsum will range between 85 and 95% pure. Often it is used as mined, although in certain cases, one or more forms of mineral beneficiation are employed to upgrade the product.

Jan 1, 1975

By Robert M. Rudio

Montana is leading the way in the field of mined-land reclamation with new laws and new ideas. The Montana Department of State Lands is combining new legislation and practical application techniques to all mining operations in the state. Road building, stream relocations, or settling systems can be designed to meet the environmental problems. Mineral exploration now requires a new and closer look at drill site locations, road gradients, and exploration tools. The problems and costs of land rehabilitation must be thoroughly understood by the exploration geologist in order to satisfactorily conduct exploration in Montana.

Jan 1, 1975