Search Documents

By S. Ramachandran, L. A. Vazquez, N. L. Grauerholz

A novel process is described for the selective flotation of scheelite from low-grade (- 0.5% W03) tungsten ores having appreciable quantities of calcareous and siliceous gangue minerals. Specifically developed for the Tempiute, Nevada facility of Union Carbide, the process yields tungsten concentrates exceeding 15 percent W03 with at least 85 percent recovery. This condition was not achieved through conventional processes. This process consists of conditioning the ore pulp with judicious amounts of lime, followed by soda ash and sodium silicate as modifiers. The scheelite is then floated using a mixture of oleic and naphthenic acids as collector. Contrary to the common observation as to the deleterious effects of calcium in fatty acid flotation systems, lime addition is found to be beneficial in achieving satisfactory results. The process has also shown excellent results on a Brazilian scheelite ore.

Jan 1, 1976

By Robert J. Ramsey, N. Finkelstein, Robert D. Jeppson

Introduction The Utah Copper Division of Kennecott Copper Corporation will present its contribution to the A. M. Gaudin Flotation Symposium in four parts. The first two segments will discuss briefly the historical development of the Utah Copper Division and describe the ore body. The third segment will review the facilities and operating procedures for the Utah Copper Division's newest plant, the Bonneville Concentrator. The fourth segment describes flotation process circuitry, including molybdenite recovery procedures, at the Arthur and Magna concentrators. (The Bonneville concentrator is a crushing and grinding unit and does not have its own flotation plant). 1. Historical Development Progress through change has been the key to the successful operation of the Utah Copper Division for more than 70 years. As the original low-grade copper operation, the pressures to remain competitive and profitable have dictated the timing and extent of each change. Much of the change has occurred through technological and economic advancements in the area of ore concentration. The Utah Copper Division of Kennecott Copper Corporation had its origin June 4, 1903, when the Utah Copper Company was organized. The initial mill of 300 tpd (tons per day) capacity was built at Copperton a few miles below the present Bingham Canyon mine site. From 1904 to 1910, the Copperton mill was expanded to a capacity of 1,000 tpd, and all of the known apparatus for gravity concentration were evaluated.

Jan 1, 1976

By Simon D. Strauss

COPPER In terms of mining activity, copper is the leading nonferrous metal. It is true that in recent years the volume of aluminum consumption in the non-Communist world has exceeded the volume of copper consumption, but virtually the entire primary aluminum supply is derived from bauxite. On the average, only four tons of bauxite need be mined to produce a ton of aluminum. By contrast, the highest-grade, large-scale copper mines now in operation (those in the Congo) must mine at least 20 tons of ore to produce a ton of copper. In the United States an average of 150 tons of ore must be mined to produce a ton of copper. This does not take into account the huge amounts of waste overburden that must be stripped from the open-pit mines to account for their steadily rising share of the world's copper output. Copper epitomizes the economic problems of the mining industry in many ways. Its price is highly volatile, considering its great economic importance. It has been a tool of mankind longer than any other of the base metals-the dawn of history has been classified as "The Bronze Age." World Copper Production Although copper is mined in many countries, in recent years 70% of the non-Communist world production has come from six countries. Two of these are industrialized countries and are large consumers-United States and Canada. The other four are developing countries with very small domestic requirements-Chile, Zambia, Zaire, and Peru. Heavily dependent on copper exports to sustain their domestic economies, these countries find themselves oscillating between prosperity and depression with the changing levels of copper prices. In an effort to control their own destiny, in 1968 they formed an organization of copper exporting countries (CIPEC) which was designed to study copper markets and possibly to intervene actively in these markets. (When this chapter was being prepared, no actual steps along such lines had been taken.) Many of the leading industrialized nations are wholly dependent on imports for their primary copper supplies. These include West Germany, the United Kingdom, France, Italy, and many others. Japan, now the non-Communist world's second largest copper consumer, produces only 10 to 15% of its requirements from domestic mines. Although the bulk of the copper output is smelted in the country where it is mined, there is a limited international trade in copper concentrates. Canada, the Philippines, Australia, and Papua-New Guinea are significant exporters of copper concentrates; Japan, Germany, the United States, and Sweden are importers. However, this trade accounted for only about 10% of the non-Communist world production of copper during the decade of the 1960s.

Jan 1, 1976

By Carl G. Schwenk

Rusk County is located in the northwestern portion of the state of Wisconsin, roughly 130 miles east of Minneapolis (Figure 1). The topography is generally flat with dairy farming the principal activity. Forest and swamp lands are common, as well as pasture and cultivated ground. Rusk County falls near the southern terminus of the Precambrian Shield and is covered by a thick layer of glacial drift. Outcrops are quite rare, but the few available exposures indicate that the subsurface is comprised of steeply dipping metamorphosed volcanics and sediments of Early Proterozoic age. A thin section of flatlying Cambrian sandstone is sometimes found directly under the glacial till. The depth to Precambrian basement has been recorded to be as great as 150 feet beneath the surface.

Jan 1, 1976

By B. R. Palmer, G. Gutierrez B., M. C. Fuerstenau

Flotation responses of chrysocolla and rhodonite are correlated with electrophoretic mobility and infrared spectroscopy measurements. Flotation is effected in the pH ranges in which hydrolysis of the metal ions comprising the mineral occurs. The roles of mineral solubility and precipitate formation are suggested.

Jan 1, 1976

By Edward J. Jr Walter

This paper discusses the use of slant hole drilling and water matting as an effective method of reducing costs in shaft sinking operations through a general review of cost priorities for the contractor.

Jan 1, 1976

By Jagdish C. Agarwal

Although copper ranks very low in the order of abundance of elements in the crust of the earth, it has been one of the first metals utilized by mar, at his emergence from the Stone Age, about 10,000 years ago. Use of copper for weapons, tools, utensils and ornaments dates back to the twilight of history, 6,000-5,000 B.C. Native copper outcrops and the malleability of the metal explain its very early use by the cave-dwellers. The working, melting and extraction of copper from its minerals are among the oldest metallurgical achievements of the human race. The oldest complete smelting installations for the extraction of copper from its minerals, dated about the fourth millenium B.C., were recently discovered in the Timna Valley, Wadi Arabah, Israel. (1) The history of the developments of the extractive metallurgy of copper has been adequately reviewed recently. (2,3) The center of copper production migrated from the Eastern Mediterranean to Northern Europe (Mansfeld, Germany, Swansea, Wales) towards the end of the Middle Ages (1500 A.D.). The production of the metal was boosted tremendously in North America since the end of the nineteenth century (Fig. 1).

Jan 1, 1976

By Richard J. Gonzalez

The petroleum industry includes varied and extensive operations required to supply increasing quantities of refined petroleum products and natural gas that are essential for the economic progress of an expanding population Petroleum has provided the power for the transformation from the "horse and buggy days" to the age of jets and space exploration, and for the remarkable improvement in productivity per worker in agriculture and manufacturing. Without increasing quantities of oil and gas, the world would face painful readjustments to more expensive forms of energy and lower standards of living Petroleum operations start with exploration, development, and production activities that supply the basic crude oil and natural gas Pipelines, ships, barges, and trucks first transport the raw materials to processing centers and then move the finished products to the ultimate consumers. Processing plants extract liquids from natural gas and refineries convert crude oil into a wide range of products These products include transportation fuels, feedstocks for conversion into numerous products (such as fabrics, rubber, and plastics), light fuels for heating, lubricants, and heavy residual materials (industrial fuel oil, asphalt, and coke) The final activity of wholesale distribution and retail marketing moves products into millions of homes, farms, industrial plants, and motor vehicles The use of coal exceeded that of oil and gas until 1946 in the United States and until 1968 in the rest of the world. However, oil and gas have proved to be such convenient and attractively priced fuels that they now supply three-fourths of the total commercial energy (including coal, hydroelectric, and nuclear power) used in North America and more than one-half in the rest of the world. LARGE SCALE OF OPERATIONS By the beginning of 1970, world crude oil production exceeded 43 million bbl daily, -equivalent to more than 2200 million tpy In addition, natural gas and the liquids recovered from processing natural gas supply about 40% as much energy as crude oil Production of oil and gas provide by far the highest value of all mining operations. In the United States, the value of oil and gas production in 1969 of $13 8 billion exceeded the $13 0 billion value for all other minerals The rate of expansion in use of petroleum has been extremely rapid since World War II World crude oil production doubled from 7,500,000 bbl daily in 1946 to more than 15,000,000 bbl daily by 1955 It doubled again to 30,000,000 by 1965, and will double again by 1975 The use of natural gas has increased greatly in the United States and also in Europe, as important discoveries in the Netherlands and the North Sea and technology for moving liquefied natural gas from Africa provided attractively priced supplies

Jan 1, 1976

By Peter N. Yanker

The two types of dryers used in the drying of copper concentrates are the rotary dryer and the spray dryer. The rotary dryer has until recent history been the traditional drying method used, Although spray dryers have been used in the chemical field for many years it is only recently that they have been accepted for drying of copper concentrates. The comparison made here will apply in a narrower sense to the drying of copper concentrates as fed into the reverbatory furnaces of the Smelter. To compare a rotary dryer and a spray dryer, which are two totally different methods and pieces of equipment, it is best to view them as systems each made up of certain elements

Jan 1, 1976

By Yoshinori Iwasaki, Shosei Serata, Yutaka Mochida

A new comprehensive insitu instrumentation technique named this RCC Method has been developed for rapid assessment and improvement of the structural stability of underground openings. When applied to tunnel construction, the degree of present and prospective safety of underground openings can be determined in quantitative terms within 10 to 20 minutes of microcreep observation. When applied to mining, roofs and floors can be stabilized by controlling the stress conditions. This stress control method has eliminated the need for intensive roof bolting and extensive floor renewal in all cases where it was applied. Use of this technique is illustrated by field examples from the Seikan Undersea Tunnel of Japan and deep potash mining in Canada. NEW INSTRUMENTATION TECHNIQUE: THE RCC METHOD Failure problems in underground excavation usually arise in weak non-elastic grounds where conventional rock mechanics theories of elasticity are not only useless but also misleading. Presently, discontinuity planes in the ground are being considered a factor in assessing these failure problems, and while this development is interesting academically, it is not of much use in actual excavation work, where it is nearly impossible to identify and quantize all existing planes of discontinuity. Even if such an extraordinary task could be accomplished at an underground excavation site, effective use of the data would be difficult and impractical for rapid excavation work, with the possible exception of rare cases of ideally elastic ground.

Jan 1, 1976

By Ross W. Smith, Salim Akhtar

INTRODUCTION Flotation of oxide minerals, particularly silicates, with cationic collectors differs substantially from classic flotation of sulfide minerals using sulfhydryl collectors. In the case of cationic flotation of these minerals, in general: 1. There is a greater importance of electrostatic interaction between mineral and collector. 2. Longer-chained collectors are required; as a rule at least 10 carbons must be present in the hydrocarbon chain. 3. Moderate concentration of collector is required. 4. Attachment between collector and mineral appears to be less strong even though the system may exhibit a large contact angle. 5. Required conditioning time before flotation is usually relatively short. 6. There is sensitivity to slimes. 7. The collectors usually possess frothing power. 8. Selectivity of cationic collectors for specific minerals is usually poor. Almost any of the oxide and silicate minerals may be floated using cationic collectors. However, specific response to these collectors varies with mineral type. The following classes and minerals are

Jan 1, 1976

By Hugh Douglas

ANTIMONY Antimony (Sb) has been used since the early Egyptian dynasties. Prior to World War I, total demand amounted to only 6000 to 7000 tons per year (tpy). Wartime uses and rapid rise of industrialization in the Northern Hemisphere nations have pushed world antimony use to the 78,000-tpy level. An overwhelming supply of low-cost antimonial resources in the Sino-Russian bloc countries has and will continue to have a major impact on availability and price to users outside the bloc. Table 14.4.1 shows trends in world production, United States production and consumption, and prices. Demand Antimony is used principally as an alloy in lead-based metals and other alloys. Pure metallic antimony usage is small and is confined to such areas as laboratory and electronic applications. Lead-antimony alloys are used in automobile storage batteries, chemical pumps, and pipes, tank linings, roofing material, and cable sheaths. The metal increases the hardness of lead, and, for such uses as foundry printing type, reduces shrinkage for casting and lowers the melting point. Antimonial oxides are used for ceramic purposes, white paint pigments, glass forming, textile finishing, fire retardants in military clothing, matches, and solder. Wartime applications include use as hardener for bullets, an element for tracer bullets, and ingredient for producing dense white smoke for visual markers. A small but rapidly growing use for antimony is for metallic compounds in semiconductors and thermoelectric devices. In the United States demand for antimony is about evenly divided between metallic end-use markets and nonmetallic markets. In metallic end uses, antimonial lead accounts for 27% of total metallic and nonmetallic use; in nonmetallic areas major uses are flame retardants (15%) which is the fastest growing market, plastics (13 % ), and ceramics and glass (11%). While antimony has advantages in most of its applications, there are uses in which other materials can be substituted, including: mercury, titanium, lead, zinc, chromium, tin, and zirconium in paints and pigments; tin in sheathings; calcium in battery plates; and bismuth in type metal. Supply Antimony is produced from both antimony ores and as a byproduct of smelting other ores. The principal ore mineral is stibnite (Sb2S3), along with its oxidized antimonial minerals and derivatives which occur in small discontinuous replacement veins or fissure vein implacements. Stibnite occurs in quartz-gold veins and copper-lead-zinc

Jan 1, 1976

By Booker Morey, Ashok Gupta

Amid controversy, the resource recovery industry is rapidly approaching its first commercial operations. Some of the problems are reviewed along with some of the important systems that are being developed for resource recovery. Market specifications for the inorganic fraction recovered from municipal solid waste are reviewed along with the details of the unit operations that have been tested.

Jan 1, 1976

By Robert Lundquist

REAM is a unique method of rock breaking using high energy projectile impact. This report-describes the most recent in a series of tests demonstrating mining applications for the REAM method. In an underground limestone mine at Greer, West Virginia, REAM was used to drive a short tunnel and drill a large diameter borehole. Along with breakage data from these tests the goal of the program was to examine environmental problems which might result from the use of cannons under-ground. A total of 103 shots was used to advance a 14-l/2-feet high by 10-feet-wide face a distance of 5-1/2 feet. It is estimated that the 9.3-pound-concrete projectiles launched at 5000 feet per second will break an average of 0.78 tons of limestone or 67 percent of the 1.125 tons of granodiorite broken in previous tests. The 9-inch-diameter borehole was drilled horizontally by repeated axial impact for 7 feet, 2-1/2 inches by 21 shots giving an average of 4.12 inches per shot. Scaling this result to compressible impact energy yields an estimated 5.8 inches per shot for a 12.8-inch-diameter hole compared to 8 inches per ~hot for a 16-inch-diameter hole in granodiorite. Noise measurements indicate that a silenced cannon can be used within a few hundred feet of mine personnel in a room and pillar mine within the legal limit of 140 dB impulse without additional protection. Some fume measurements were made with satisfactory results, even though the military propellants used produce much greater quantities of toxic fumes than the liquid propellant proposed for the future.

Jan 1, 1976

By E. I. Robinsky

"This paper describes a new, proven approach for tailing disposal. Not only is the disclosed system less damaging to the environment, it is also less costly to operate, to close down and maintain in perpetuity. The basic concept is to discharge thickened tailing from one permanent location.This creates a conical or hill-like deposit which:(1) requires lower perimeter dykes for equivalent storage capacity;(2) eliminates decant towers and decant lines;(3) requires no steep dams built of tailing;(4) is stable:(5) requires only a small pond outside the deposit;(6) decreases pollution of the surrounding environment by water seepage and deflation; and(7) simplifies abandonment and ""closing-down"" operations.The approach is made possible by the fact that, at a sufficiently high ratio of solids to water, tailing material can be made to accumulate at slopes of 5 or 6 per cent -- considerably steeper than possible by traditional methods using low solids-to-water ratios. To achieve the necessary solids-water ratio (35 to 60 per cent), it may be necessary to install a thickener. It is expected, however, that at many concentrators it may be possible to discharqe relatively clear plant water through a line separate from the tailing line, thus reducing the load on the thickener."

Jan 1, 1976

This paper describes a plant built at The Broken Hill Associated Smelters, Port Pirie to sample lead sinter automatically. As the plant is still in the commissioning stage results on the precision and accuracy of the sampling are not yet available, but some of the difficulties experienced during commissioning are discussed.

Jan 1, 1976

By Moto Goto

Onahama Smelter of Onahama Smelting & Refining Co., Ltd. has two green- charge reverberatory furnaces; the old furnace was constructed in 1965 and the new one in 1973. This paper discusses the use of oxygen-oil burners in a green-charge reverberatory furnace and also compares the copper loss in slag between the two furnaces at Onahama Smelter. During the past ten years of operation, no shutdowns of the old furnace were necessary and the smelting capacity was increased by 25% by the use of two oxygen-oil burners. These burners are suitable for a green-charge reverberatory furnace to in- crease the smelting capacity without causing an increase of the exhaust gas volume and refractory erosion. After two years of operation of the old furnace, a bottom build-up in the charging zone of approximately 50 centimeters was experienced, and this build-up has stayed at this level since then. In 1973, a new additional reverberatory furnace was put into operation. Copper content in slag of the new furnace was lower by approximately 0.15% than that of the old one during the first several months after the start-up. Investigations were then made on the effect of the bottom conditions in the charging zone on the copper content in slag.

Jan 1, 1976

By L. C. Raymond

Valuations in the mineral industry differ from those of other enterprises because mines and oil wells have a definite life so cannot be considered a perpetuity. This requires that in any mineral-property evaluation the recovery of invested capital is necessary during the life of the property. Capital write-offs for nonextractive industries are assumed to be continuously plowed back to sustain the operation and produce yields on the capital invested. The extractive or mineral industry, however, generally attempts to return to the investor both interest and principal during the life of a property. Normally this is done currently and the dividend includes both items. Where the mineral property possesses large reserves and the life factor approximates a perpetuity, the return on investment is generally comparable to that of industrial stocks. The valuation of a mineral property, at best, is based on educated estimates and judgment factors. This is particularly true as it relates to estimating selling prices over a long term or assessing the quality of management. Also, it is possible to make various assumptions as to rapidity of working out the deposit, varying time for start-up of operations, varying earning rates, so as to obtain different results with the same basic facts. Thus it is not surprising that two engineers, irrespective of their abilities, may not agree exactly even when given the same facts, but their results should be close enough to be used in establishing a fair value for trading purposes. The valuation is no better than the source of basic data and the soundness of judgment factors. Fundamentally the basic principles of mineral valuation are similar for base metals, sulfur, oil, or any other mineral. Each mineral, however, requires an engineer to have a knowledge of such factors as its occurrence, distribution, mining and processing methods, and marketing problems in order to gather and analyze all the facts and data that have a bearing on the earning potential of the property. Present Value of a Mineral Property In essence the present value of a mineral property is a sum of money in today's dollars that future income from the property are worth. It differs from the total anticipated earnings by the amount of the interest that the unrecouped investment could be expected to earn during the period of recoupment. Thus, if one could accurately estimate what a mineral property will earn during its life, after deducting all operating, administrative, capital, interest, and tax charges, the determination of present value would be a relatively simple mathematical calculation. Normally, where the expected life of the mineral property extends beyond 20 or 25 years, the discounted value of earnings beyond this period is relatively small. The petroleum industry generally discounts the annual cash flow of an operation rather than earnings since, for tax-saving purposes, earnings are kept

Jan 1, 1976

By Kelly BJ, Smith GA

The recommendations of a recent American report on "Better contracting for Underground Construction" are considered in relation to Contracting practices on major Australian projects by representatives Of the "classical trilogy" - the Owner, Engineer and Contractor.

Jan 1, 1976

By Joseph D. Martinez

"The benefits of modern technology can readily be identified with energy availability. A clear correlation has been established between per-capita energy consumption and the GNP for various nations. The United States is an outstanding example of a nation which has benefited from vast energy reserves. The nation is now challenged, how¬ever, by dwindling reserves and the need to develop new sources consistent with the preservation of environmental quality. The development of new, virtually inexhaustible and environmentally acceptable sources cannot be expected for several decades. Meanwhile, we will have to depend on coal, nuclear energy and/or rigorous conservation measures.The net effect of environmental considerations has been to delay and perhaps ultimately eliminate the nuclear energy option as a national energy alternative. This forces a more positive move toward coal as the next major source of electrical power. Our coal resources are large, but the use and production of coal is also a threat to the environment. Thus, we seem to be moving from one major accessible source to another due to environmental concern only to face the probability that the alternative is also environ¬mentally unacceptable.Controversies revolving about energy choices must be resolved by an analysis of the relative benefits and impacts of these two sources and others. The pattern of changing energy sources is not new. We have moved from wood to coal to oil and gas in the past and must learn to adapt in the future. Rational decisions must be made relative to the utilization of intermediate energy sources pending development of promising future approaches. A collapse of current levels of energy supply could threaten our technological society and the means to develop a new energy base."

Jan 1, 1976