Search Documents

By Richard A. Hunnisett

Silica sand is one of the world's most plentiful resources and is a basic necessity in our way of life. The end uses of silica sand are an integral part of our homes, transportation, and places of work. The environmental legislation enacted in the early 1970's, coupled with the oil embargo and higher than normal inflation, have had a very real impact on the industry and its primary consumers, the foundries and glass producers. The present environmental laws directed at air and water pollution and the working environment can, in most cases, be met, but not without large capital expenditures for equipment. These expenditures must reduce the funds available for expansion and modernization of existing processes which are necessary if the costs to produce industrial sand are to remain at acceptable levels. The concern for the future is the enactment of more stringent laws, and the available technology and equipment to economically comply with them.

Jan 1, 1978

By Woodcock J. T

A sulphide ion selective electrode (ISE) is suitable for control of sodium sulphide additions in flotation because it has a rapid response to changeS in S2- concentrations, can indicate -low concentrations at differentpH values, suffers from few interferences, and is robust enou'gh to use in a pulp. Three sulphidization techniques were studied using the lSE electrode for measurement and/or control of S2- levels. Metallurgy was assessedfrom concentrate grades and copper recovery.With slug additions of sodium sulphide, sulphidizing conditions were poorly defined and reproducibility tended to be poor. Although acceptable metallurgy could be achieved by multiple additions, sodium sulphide consumption was high.Controlled potential sulphidization readily gave good metallurgy. The optimum potential of the lSE for sulphidizing was about -500 mV versus SCE, but depended on sulphidization and flotation times; suitable times were3 and 5 min respectively for three to five stages. Application of this technique to previously untested ores gave good metallurgy in a first test in spite of variation by a factor of three in the sodium sulphide requirements ofthe ores.Simultaneous sulphidization and flotation was satisfactory when conducted at an lSE potential of -450 mV versus SCE. Mixed cha!copyrite-oxide copper ores responded satisfactorily.Besides optimizing sulphidization conditions it is also necessary to optimize xanthate additions (e.g. by measuring xanthate residuals).

Jan 1, 1978

The recommissioning of the plant at Mary Kathleen involved several distinct phases. The previous plant process was modified significantly, the plant capacity was increased by the addition of new equipment and the exist- ing equipment was in most cases overhauled. This equipment was either reused in its original duty or relocated. Maintenance requirements after the plant was cmommissioned were high because of the amount of modified equipment and also because some old items of equipment were deliberately not overhauled during recommissioning. The equipment that was overhauled has operated reliably. However some new equipment has not been as satisfactory.

Jan 1, 1978

By M. Dayne Aldridge

A discussion of the definition of automation in mine ventilation applications is presented. The results of theoretical studies, experiments and practical experience from work in the United Kingdom, Belgium, Poland, the Soviet Union and the United States are summarized. Conclusions are drawn from these efforts and the prospects for the future development of automatic mine ventilation systems are explored.

Jan 1, 1978

By K. Voltaire

As can be guessed from the subtitle, this paper will not be a geologist's one since neither of the authors is a professional geologist. This will be an attempt to present the various aspects of the legal, economic and geological setting that condition the exploration for mineral resources in Haiti. Before going any further, we are going to present a summary of our rather short mining history. One must first mention that Caribbean countries are latecomers to the mining business. If we go back to the colonial period (1500-1600's) there are net many traces of mining activity. The major exception to this is the recovery of alluvial gold in Hispaniola, Puerto-Rico and Cuba and also some sporadic copper mining in Hispaniola (notably in Haiti near the city of Gonaives and in some of the old mining districts in Santo-Domingo). These easily minable deposits were quickly exhausted and mining quite naturally came to an end as agriculture rose as the major economic activity. In the Haitian case, aside from very erratic mention during the 19th Century of the presence of some minerals (i.e. haematite, chalcopyrite) no serious geological work was undertaken. In the meantime, the peasants in the northern part were still looking for alluvial gold in some streams but this amounted to next to nothing. One has to come to the 1920's to find the first comprehensive geological survey. At the time, the country was under the military control of the United States. The American Government sent a team from the U.S.G.S. headed by the late W. Woodring to initiate a survey of the country. Given the lack of transportation, this was a tough task and Woodring and his associates did it magnificently. As a result of their efforts, they published a very thick piece of work of more than 600 pages. "The Geology of the Republic of Haiti" although it was published in 1924 is a classic and is a must for anyone interested in the geology of Haiti.

Jan 1, 1978

By J. E. Matta

The Bureau of Mines has developed a tracer gas method for measuring leak-age through permanent mine stoppings. In this method, a temporary brattice is erected in the same entry as the leaking permanent stopping. Leakage was evaluated from concentration measurements of a tracer gas introduced into the space between the stopping and brattice. Stopping leakages ranging from 15 cfm to 265 cfm were simulated in an underground coal mine. Leakage values determined by the new method were within 10 pct of the known values.

Jan 1, 1978

By Roach C

Exploration on the Callide Coalfield by Thiess Bros. Pty. Limited had reached the stage in mid 1976 where there was a need for a comprehensive appraisal of the coalfield geology. Exploration strategy in 1977 - 1978 was defined by the selection of the most attractive targets. All available literature, reports and plans were reviewed and borehole records assessed. The geology of the coalfield was placed in its regional setting and the genesis of the Callide Coal Measures described in a structural and sedimentological context. Their general form and extent was then examined by the technique of stratigraphic analysis through the interpolation and extrapolation of the available data. A "localized" reserve classification was drawn up and reasonable estimates of the various geological reserves produced, in terms of their reliability and depth of overburden. Quality trend maps were also produced. The resultant "base map" was virtually a summation of all the information to June, 1977, and the basis for the exploration programme in the 1977 - 1978 financial year. The technique allowed for "base maps" to be produced at almost any stage, each one a refinement of its Predecessor.

Jan 1, 1978

By Wayne D. Gould, Robert S. Shoemaker

Modern mill design is a combination of many factors which permit the efficient production of a mineral concentrate from operating, maintenance, and capital requirements. In general, mills should be designed to use the largest possible equipment compatible with the requirements of the ore and the owner's operating philosophy. The paper discusses the major parts of concentrating mills, from primary crushing through comminution, both conventional and autogenous, and the production of a final concentrate. Features of various plants are compared and discussed in the light of operating practice and maintenance requirements.

Jan 1, 1978

By A. F. Colombo

In an effort to maintain an adequate supply of iron to meet national economic and strategic needs, the Bureau of Mines, U.S. Department of the Interior, is conducting research on methods for beneficiating the oxidized taconite resources located on the western Mesabi range in Minnesota, thus expanding domestic iron ore reserves. The selective flocculation and cationic flotation process was investigated in a pilot plant using an ore feed rate of 410 kg/hr (900 1b/hr) and 88 percent recycled water. Lime and a cationic flocculant were used to clarify the waste slurries treated in the water reclamation circuit. An oxidized taconite assaying approximately 36 percent Fe yielded concentrates averaging 63.5 percent Fe and 4.3 percent SiO2 and having an average iron recovery of 84.4 percent. The estimated reagent cost per tonne of concentrate was approximately $1.10. In an attempt to recover more of the iron lost in the flotation tailing, wet high-intensity magnetic (WHIM) separation was incorporated in the pilot plant circuit. The flotation concentrate grades obtained from beneficiation circuits with and without WHIM scavenging were similar, but when WHIM separation was used the overall iron recovery was increased by 2 to 9.5 percent, depending on the iron assay of the flotation tailing.

Jan 1, 1978

By Bell LC

Overburden removal, mining and reclamation are now accepted as the basic operational steps involved in the winning of coal by open cut methods. To attain the lowest operational cost, the recontouring and revegetation of spoilpiles must be planned concurrently with the planning of overburden removal and mining. The earthworks associated with reclamation work on spoilpiles often account for 75 - 90 per cent of total reclamation costs. Experience at Callide Mine has shown that the way that spoilpiles are contoured does influence water retention and can reduce erosion from rainfall run-off. However, provided the recontoured slopes meet'Mines Department specifications, the quality of reclamation work is judged not by the quality of the earthworks but by the plant regrowth on the reshaped surface. Thus it is the quality of the revegetation which is of prime importance. For vegetation to be successful, time must be spent on planned research into methods of overcoming plant nutrient deficiencies and selection of suitable grass and tree species. The research programme undertaken at Callide Mine consists of three stages :- laboratory studies glasshouse trials field trials

Jan 1, 1978

By L. R. Gremillion

Chemical and mineralogical data on 25 apatitic phosphate ores of diverse origins from commercial deposits around the world were widely variable. From 14 to 18 chemical constituents of each sample were determined, and each sample contained 4 to 10 mineral phases. Altogether there were 34 different mineral phases, many of which occurred in only one sample. The samples contained varieties of francolites, fluorapatites, and mixed hydroxyl-fluorapatites. The apatite compositions calculated from the chemical data showed that certain types of substitutions were characteristic of different apatite varieties, but every variety had some degree of substitution of (CO3)2 for (PO4)3 and the P2O5 contents of the apatites ranged from 35.1% for a North Carolina apatite to 41.9% for a Missouri apatite. In a concentrate with a grade of 32% P2O5, the North Carolina sample should contain about 8.7% gangue and the Missouri sample about 23.7% gangue. To optimize the digestion process of a phosphate are, it is necessary to consider the dissolution behavior of the different mineral phases during acidulation and the effects they may have on the chemical properties of a fertilizer intermediate. In the production of wet-process acids or superphosphates, the acidulation of certain minerals may cause foaming and formation of sludge, filtration, corrosion, and handling problems.

Jan 1, 1978

By Ronald L. Wiegel

In a mineral processing plant there are a number of routine decisions which are based at least in part on the plant's metallurgical performance. Among these are those related to: 1) equipment functioning properly 2) suitable operating conditions 3) reagents achieving desired results 4} determining operating response to changes in ore 5) defining circuits offering potential for improvement A step beyond the routine, are the periodic management evaluations of operating supervision and technical assistance, which are based largely on profit -a direct function of are availability, metallurgical performance and operating costs. The "yardstick", excuse me -"meterstick", by which performance is best measured is the plant metallurgical balance, which tells not only what was produced but how it was produced. Since this metallurgical balance is directly related to both plant profits and individual rewards, it is only reasonable to make that "meterstick" as precise as humanly possible.

Jan 1, 1978

By D. Montagna

This Bureau of Mines report describes a salt-free, fluxless method for reclaiming metallic aluminum from aluminum dross. The dross is smelted under argon, nitrogen, or carbon dioxide, instead of a salt flux, in an externally heated pot furnace. Aluminum recovery, using argon, is equal to recoveries reported from commercial smelters that process dross in rotary-type furnaces This salt-free method could offer a reduction in air pollution, lower energy requirements by elimination of salts, and the production of up to 60 percent less solid waste for disposal than the salt method.

Jan 1, 1978

By James R. Aggson

This paper summarizes the research effort that was conducted as part of a cooperative agreement between the U.S. Bureau of Mines, Denver Mining Research Center and the Pittston Company. The objective of this investigation was to further the understanding of the floor heave ground control problems that have plagued underground mining of the Beckley coalbed in southern West Virginia. Floor heave is both economically and structurally undesirable. Floor heave is accompanied by a redistribution of stresses and loads that are associated with an underground opening. This redistribution of stresses may cause roof or pillar problems that otherwise would not have occurred. The floor heave that occurs in the Beckley coalbed is not cons1dered to be caused by "squeezing" or plastic flow of the materials involved. The "squeezing" type floor heave is normally associated with relatively weak floor members that contain significant amounts of clay mineralization. The floor members in the Beckley coalbed are competent, relatively strong materials which fail in a manner that can best be described by the term "buckling." This buckling-type failure is indirectly related to the time-dependent deformation properties of the materials involved, but is considered to be more of a slender column, or panel, type failure than a "squeeze" or "flow"-related failure. The Beckley coalbed has had a history of floor heave ground control problems. The Glen Rogers mine, which opened in the 1920's, experienced extensive floor heave. In a report dated April 1929, James P. Keatley of the West Virginia State Department of Mines described the floor heave in the Glen Rogers mine. Several observations listed in the Glen Rogers report that appear to be consistent with current observations follow: 1. Water plays no apparent part in the floor heave process. 2. No evidence of gas has been found in the floor. 3. The thickness of the overburden, which varies from 183 to 396 m (600 to 1300 ft), has no relationship to the floor heave. In the conclusions of the 1929 report on the Glen Rogers mine, Keatley states, "A statement in brief as to the cause (of floor heave) would lie that an undetermined natural condition doubtless augmented by former and present mining methods causes the bottom to heave." As this report will show, Mr. Keatley's insight into the problem was most accurate. The "undetermined natural condition" is the existence of a biaxial, horizontal, compressive stress field. This stress field is in excess of that which would be expected from gravity loading. This stress field and the material properties of the floor rock combine to cause the floor heave that has been experienced. The floor heave that occurs in the Beckley seam generally occurs as arching, with a tension fracture, near the center of the floor span or as a break near the rib followed by vertical deflection (of the floor) at the rib and sloping of the floor across the entry. Examples of the floor heave are shown in Figures 1 and 2. The two types of floor heave are merely different manifestations of the same basic failure mechanism. When the entries experiencing floor heave were identified on a map of the mine under investigation, it was apparent that there was a relationship between the floor heave and the direction of the entries. The main entries, which are used for ventilation and haulage, experienced the majority of the floor heave. This directional relationship suggested a directionally related loading mechanism, or more specifically, a biaxial, horizontal stress field that exceeds what would be expected by gravity loading. Since the main entries were oriented at a bearing of N25oW, it was hypothesized that the maximum compressive component of the horizontal stress field was at 90° to these entries or at a bearing of N65oE. An in Situ testing program was developed to test this hypothesis and investigate the floor heave problem.

Jan 1, 1978

By Peter F. Steidl

Seven degasification wells have been completed in the Pittsburgh coalbed at the new Emerald mine near Waynesburg, Pa. Funding was provided by the Bureau of Mines to perform stimulation treatments on five of the wells, to show that this is a feasible and economical means of degasifying part of a coalbed. The seven wells ranged in depth from 590 to 910 feet. Stimulation treatments used 25,260 to 42,660 gallons of foam and 7,400 to 12,800 pounds of 20/40-mesh prop sand. Pumping rates were 10.8 to 11.6 bbl/min and treating pressures were from 1,050 to 1,600 psig. On the day following stimulation, gas production ranged from a few hundred cubic feet per day to more than 100,000 cu ft/day.

Jan 1, 1978

By Bradley AJ

Hamersley Iron Pty. Limited mines and pro cesses iron ore from two orebodies at Tom Price and Paraburdoo, situated in the North West of Western Australia. Conventional open pit mining methods are used at both sites in that material is drilled and blasted in benches, loaded by shovels and hauled to the Primary Crushers or dumped on waste or low grade material stockpiles. The present drilling fleet, consisting of eight high capacity Bucyrus Erie Rotary drills has evolved from an initial fleet of a large number of small percussion rigs. There are significant physical differences between the ore types encountered at both mines which nec- essitate the drilling of smaller diameter blast holes at Paraburdoo than those at Tom Price. The drilling practice at each site is dis- cussed, with examples of performance achieve- ments under varying drilling conditions.

Jan 1, 1978

Proposals designed to use stockpiles and buffer stocks to achieve price stabilization and better resource use have a long history. They are super- ficially simple to understand. The benefits seem clear. And yet I am well aware that this is not a simple subject: the more one studies it, the more complex it becomes. Worldwide interest in re- source management, while receiving fresh impetus from the OPEC actions, also has a long and chequered history. Those venturing into such ter- ritories must be forewarned of the traps and pit- falls which abound. Interest in these schemes has waxed and waned over the years with the fluctuating fortunes of the producers or consumers. As I write this paper towards the end of 1977, I am acutely aware of the low ruling prices for zinc, copper, and nickel. These sacrifice prices remind me that it is difficult, for example, for a surveyor, to be calm and rational if he is up to his neck in a swamp full of crocodiles. He might be forgiven for forgetting that the aim was to drain the swamp! I am also aware that when swamps are drained, painful and dangerous stumps sometimes stick out. Hence, in looking at the subject of stockpiles and resource management we must not set our sights too high, perhaps not initially hope for perfec- tion, if we want to secure worthwhile changes. My approach is to acknowledge a bias for the market system. We have, however, had experience (remember the 1930s) of some weaknesses in the untrammelled operation of free markets. Thus our international economic relationships over the past 20 or 30 years have been based on a desire to retain as much as possible of a liberal world trading system backed by such organizations as the GATT, IMF, and the U.N. to ensure the necessary cooperation. Some nations have seen this system work only partially in their best in- terests. GATT, for example, has been reasonably effective in liberalizing trade in many manufac- tured goods but far less so in regard to agricultural or semi-processed goods.

Jan 1, 1978

By Daryl E. Radcliffe

The Bureau of Mines studied the displacement of the roof in a portion of the Bear coal mine near Somerset, Colo, Horizontal-and vertical-displacement gages were installed in a five-entry section during normal room-and-pillar mining procedures. Monitoring of the roof continued until this section was mined out. Displacement measurements in combination with known time lapses between mining and bolting operations indicate that once support is achieved, the length of unsupported time does not appear to affect long-term roof stability in the mine under investigation.

Jan 1, 1978

By H. H. Dewing

The Bureau of Mines conducted a laboratory-scale investigation of a technique that produces zinc sulfate and elemental sulfur from sphalerite concentrates by reaction with sulfuric acid at 175° to 200° C and ambient pressure. The objective of the investigation was to develop a hydrometallurgical method of producing zinc from sulfide concentrates that does not generate sulfur dioxide pollutants. Reaction with 80-to 85-pct sulfuric acid produced 4 moles of sulfur for every 3 moles of sphalerite reacted, with minimal production of sulfur gases under optimum conditions. More than 98 pct of the zinc was recovered as zinc sulfate after 3 hours at 175° C. The reaction mixture was leached with simulated spent zinc electrolyte containing 13-pct sulfuric acid to recover zinc sulfate from the insoluble, high-sulfur residue. Neutral zinc sulfate, which is required for electrolysis, was separated from the sulfuric acid solution by crystallization as ZnS04?7H20 at -10° C. Up to 80 pct of the water in the recycled electrolysis solution was removed by the crystallization process; evaporation was used to further concentrate the sulfuric acid for reuse in leaching sphalerite. Advantages of the proposed method over conven-tional roasting and leaching include virtual elimination of sulfur dioxide, production of a solid sulfur byproduct, and higher zinc recoveries due to elimination of zinc ferrite losses.

Jan 1, 1978

By F. Milton Lewis, Edward S. Frohling

The information which is required for' a preliminary feasibility study and the additional information which is required for the final feasibility study on a new mineral deposit are discussed. The preliminary feasibility study is made from very little information and at a minimum cost to the owner. However, the outline for the preliminary report is similar to the one used in the final report. In this manuscript, it is assumed that the results from the preliminary study are favorable and the owner authorizes a final feasibility study by an outside engineering company. The type of organization for completing this final feasibility study is described. The final reports includes all information and data relative to this new mineral deposit. This information is presented so that it may be understood by financial people as well as by technical people.

Jan 1, 1978