Search Documents

By R. W. Kobler

The pelletizing process for low grade iron ores has undergone continual changes since its inception over twenty years ago. These changes have necessitated filtration equipment changes in order to produce a product suitable for balling. With modern techniques it is now possible to produce pellets of 68% Fe from ores containing as low as 26% Fe. Low grade ores require fine grinding to liberate impurities This shift to finer grinds over the years has necessitated major changes in the filtration steps. Techniques are now available for producing suitable product from ores with Blaines as high as 3600 cm2/gram. This has been made possible by the development of high performance filters. Recent developments have reduced maintenance costs and produced higher production reliability. The paper discusses iron concentrate filtration from its beginning to present day design. It will be shown that the dewatering step prior to balling has gone through four generations of filters. Particular emphasis is placed upon hydraulic studies which have allowed today's optimum designs.

Jan 1, 1978

By Fred N. Kissell, J. E. Matta, J. C. LaScola

The methane gas emitted from coal samples collected from the conveyor belts dumping into silos was measured by the Bureau of Mines. Approximately 50 pct of the total gas desorbed into a sealed can within 1 week was released during the first 24 hours. No simple correlation between the gassiness of the coal stored and the methane concentration in the silo open space above the coal was found. This was probably because the gassier coals were stored in open-top silos, which were better ventilated. Although the methane concentration in the open space above the coal pile was less than 1 pct for all 34 silos investigated, a methane measurement in the coal pile showed that high methane concentrations can exist. The methane released in the pile appears to accumulate and not liberate freely into the open space above the coal pile. Probably this gas is released during reclaiming operations, but further research is required to substantiate this claim.

Jan 1, 1978

By C. Bailey Williams

Aragonite "sand," an oolitic lime-stone, is distributed throughout the Bahamas on the Grand Bahama Bank, adjacent to Southeast Florida. Bahamian deposits hold 75-100 billion tons of recoverable Aragonite. Aragonite's precipitation from seawater over 700 years ago assures low contaminates, making it a pure material for such industries as cement, glass, etc. A 90-acre, man-made production island was built south of Bimini, adjacent to ocean shipping channels mining is by cutterhead, suction dredge, dewatering, and stockpiling for further drainage and shipping. Aragonite is transferred to the U. S. East and Gulf Coasts via bulk carriers to points of sale.

Jan 1, 1978

The London Metal Exchange began its first official session of aluminum trading on Monday, October 2, LME prices based on 3-month forward contracts opened Monday at 52.4 cents per pound, fell midway through the week to 52.3 cents and ended Friday at a high of 52.7 cents. For the week, LME metal averaged 52.5 cents. Although Reynolds Metals Co. and Aluminum Co. of American continued in September to value unalloyed 99.5 percent aluminum ingot at 53 cents per pound, other producers were at higher positions of 55-57 cents. Alcan Aluminum Corp. of Alcan Aluminum, Ltd., a Canadian producer, increased prices for its U.S.-marketed ingot by 2 cents to 55 cents per pound, effective September 21. New York merchants increased ingot quotes by approximately 0.5 cents to 52.8-53.5 cents per pound.

Jan 1, 1978

By Chris Mills

The role of gravity separation in the mineral industry is briefly considered in perspective. The mineralogical and laboratory approaches to gravity process design are examined with emphasis on process technology selection. The equipment available for small scale and pilot test-work is discussed, particularly in regard to scale-up and the acquisition of reliable, accurate data. Transposition of performance data from pilot scale to plant scale is explained. The available types of full scale gravity separation equipment are discussed with emphasis on large high-capacity units. Plant layout and selection of ancillary equipment are considered.

Jan 1, 1978

The Split Rock low grade copper prospect was discovered in 1969 by Cyprus Mines Corporation using stream geochemistry. Cyprus "Imes carried out geochemical and geophysical investigations, geological mapping, and percussion and diamond drilling, and concluded that the grade of mineralisation was too low (0.1% copper) to be of interest. In the present study, the geology was remapped and very substantial differences from the previous observations are recorded. (lineraliced acid dykes in a 1 000 foot hole drilled by Cyprus Mines had a total inter- section of almost 300 feet with an average crade of 0.4% copper. Surrounding drill holes at distances of 500 feet did not intersect +hese dykes. This group of drill holes occupies a small part of an area about 2 km by 1 km which was affected by intense quartz sericite pyrite alteration along many fractures with an associated soil copper anomaly. It may be that the quartz sericite alteraiion with feeble copper mineralisation represents hydrothermal alteration emanating `rom a mineralised intrusion of which the dykes mentioned above are off shoots.

Jan 1, 1978

By Herbert D. Drechsler

Mining Finance-is the interrelated aspects of "determining the total amount of funds to employ in a mining firm; allocating these funds efficiently to various assets; and, obtaining the best mix of financing in relation to the overall valuation of the firm". The first section is an overview of the financing problem through examination and discussion of the Balance Sheet and Income Statement. The next section is a discussion of the nature of the criteria developed in feasibility study. The third section describes type of capital funds, and the final section describes case studies of mining finance.

Jan 1, 1978

By J. C. Watts

Monitoring and control of conventional industrial wet grinding circuits is conceptually straightforward. However, since production objectives and operating constraints can vary widely from plant to plant, there is probably no single overall grinding circuit control strategy which is "best" in all cases; in-variably some compromise is necessary between performance desired under ideal conditions and performance achievable in practice. The recent advent of relatively low cost, reliable, high speed small computer systems is revolutionizing daily operations in increasing numbers of metallurgical processing plants. Of special power and capability is a hierarchical computer network like that currently in use at the Pinto Valley Operations of the Cities Service Company. Several satellite processors for key plant areas communicate with a master computer operating under a powerful multitasking real-time operating system. Hardware and software structure is such that downtime on one of the processors -including the master -does not have a major impact on overall system operation. Admittedly, the powerful, core efficient table driven satellite software, which handles process/computer communication, calculation of nonmeasured process variables, and basic Direct Digital Control functions, is difficult to modify. However, important high level process monitoring, report preparation, graphic display, and supervisory control functions -including economic optimization -can be implemented by project engineers at the plant site. Thus, for example, new control strategies can be quickly examined and rapidly evaluated. Such computer monitoring capability also permits use of short duration process pulse tests for approximate dynamic modeling and rapid calculation of controller tuning constants for single loop dominant systems. Following a brief back-ground discussion of the Pinto Valley Project, we present some of the more interesting results and conclusions of our work over the past year.

Jan 1, 1978

By Robert R. Turner, Arthur R. MacPherson

This chapter reviews the steps which should be taken from the time it is decided to consider autogenous grinding in the development of a new ore deposit or the expansion of an existing plant up until the purchase of the new autogenous mills. In this case the term autogenous includes semi -autogenous, secondary pebble mills, and lump milling as well as fully autogenous grinding systems. Also, both wet and dry grinding alternatives have been included. Before the test program it must be decided how many bulk samples are required to properly assess the autogenous grinding possibilities of the deposit. Also, a decision must be made on where and how the samples are to be ground i.e. pilot mill at site or in established location, wet and or dry grinding, etc. In the test program itself, certain fundamental data must be obtained. The testing should include enough work to determine whether fully autogenous or semi-autogenous grinding should be used and what type produces best power efficiency. Also, all the other pertinent data should be collected such as power; tonnages; feed, charge, and product sizing; circulating loads, etc. If a secondary mill is required to produce a final grind the decision on whether a pebble or ball mill should be used may require additional test work. Finally, the concentration of the mineral may play an important part in selection of the circuit and should become a part of the final testing once the grinding has been established.

Jan 1, 1978

By John W. Motter

The Green Mountain Copper Prospect is an unusual stratiform base metal occurrence located in the California Foothills Copper-Zinc Belt. Mined for rich secondary oxide-carbonate ores since 1863, the first serious exploration of the primary ores was in the 1970's. Unlike typical volcanogenic deposits of the district, stratigraphy consists of greywackes overlain (?) or intruded by an intermediate to felsic volcanic unit. Shales and siltstones overlie the volcanic unit. Massive pyrrhotite, chalcopyrite and sphalerite occur at the top of the volcanic unit. Later intrusion and deformation metamorphosed the sequence and created a SW plunging anticline. Characteristic magnetic and electrical geophysical signatures are present and reviewed.

Jan 1, 1978

By Paul H. Miller

After passage by the Congress, Public Law 95-87, the "Surface Mining Control and Reclamation Act of 1977" was signed by President Carter on August 3, 1977. This law, in its simplest form, was intended to control the environmental effects of surface coal mining and to ensure that mined land is restored to a condition equivalent to that prior to mining. Immediately after the signing, the wheels of government bureaucracy began turning to establish a new federal agency -the Office of Surface Mining Reclamation and Enforcement or OSM -in the Interior Department that would implement the provisions of the Act. Since this took time and because the Congress had not yet provided funding for OSM, a special task force was assembled within the Interior Department to begin the task of writing interim regulations to implement the Act. With respect to the use of explosives, the Act specified that a blasting plan be included in the application for a mining permit. The blasting plan will outline the procedures an operator will use to meet specified environmental protection performance standards. The performance standards established by the Act require explosives to be used only in accordance with existing state and federal laws and regulations and with regulations to be promulgated by the regulatory authority. The regulatory authority was defined as either a state agency operating under an approved state program or the OSM operating under a federal program. As a minimum, it was specified that the regulations should include provisions to require that: 1) a blasting schedule be published in a local newspaper and be mailed to local governments and to all residents living within 1/2 mile of the blasting site . 2) daily notice be given to residents in the area prior to blasting. 3) blast reports be prepared that are maintained for three years and available on request to the public. 4) blasts be designed to prevent injury to persons, damage to property outside the permit area, adverse impacts on underground mines and adverse effects on ground or surface water channels or availability outside the permit area. 5) upon request of residents or property owners within 1/2 mile of the permit area, preblast surveys shall

Jan 1, 1978

By R. R. Culbert

Several thousand parts per billion of uranium are present in some alkaline lake and ground waters of the Okanagan region, British Columbia. To a major extent the uranium content of these highly anomalous waters is controlled by their levels of dissolved bicarbonate. In lakes, dissolved bicarbonate and the organic content of the sediment largely control the partitioning of uranium between sediment and water. This relationship is found to a lesser extent in alkaline creeks, and transported geochemical anomalies in soils appear where uranium-bearing alkaline ground waters have encountered organic materials. There is a possibility that young, near-surface deposits (with very low radioactivity) are forming from these uraniferous waters.

Jan 1, 1978

By John D. Vincent, Howard W. Jacky

This chapter covers the normal problems encountered in the building of an ore concentrating facility. To produce such a facility In today's environment requires correlation by the engineers involved of geologic data, mine planning, scheduling, future planning, water resources, power, land availability, testing, design, start-up and environmental considerations. Of course, the program scheduling and character of the ore will determine the weight given to the above considerations in the final design and construction of the plant.

Jan 1, 1978

By Reid JG, Cutfield S

Considerable quantities of dissolved nickel are lost in the waste liquors from the QNPL nickel treatment plant. Cementation, precipitation and ion exchange techniques were investigated to reduce this loss. Ion exchange was the most successful of the procedures studied and a process for recovering nickel from stripped ammoniacal process liquors was developed in the laboratory and scaled up to plant flow volumes. The system developed uses a carboxylic ion exchange resin operated in a completely ammoniacal cycle. The regenerant is itself regenerable using existing plant, thus the only loss is the stoichiometric value of NH4+ required to displace the exchanged cations from the resin. Existing plant sand/anthracite filter beds have been adapted for use as resin columns containing 3 cubic metres of resin capable of treating effluent at a flow rate of 6000 litres/min.

Jan 1, 1978

By Laurance L. Oden

The Bureau of Mines is developing nickel catalysts for converting synthesis gas derived from coal to synthetic natural gas. The present report describes the relationship between the composition of aluminum-nickel alloys in the composition range NiAl3 to Ni2Al3 equilibrated at 840° C and the properties of catalysts obtained from them. Methanation activity was determined in the temperature range of 300° to 360° C in a flowing gas stream containing 1 pct CO, 8 pct H2, and the remainder He. One part per million of H2S was added to the gas stream at 400° C to evaluate the susceptibility of catalysts to sulfur poisoning. The total surface area was measured by the adsorption of nitrogen at liquid nitrogen temperature, and the active surface area was measured by the adsorption of hydrogen at room temperature. Total surface area and active surface area were found to increase with increasing proportion of aluminum-saturated Ni2Al3 in the precursor alloy, but methanation activity and resistance to poisoning by H2S were nearly constant. However, the methanation activity of the catalyst prepared from stoichiometric Ni2Al3 was less than half that of the other catalysts.

Jan 1, 1978

The Palabora ore consists of two types, a carbonatite containing a low titanium magnetite, and a foskorite containing high titanium magnetite. The latter type also contains substantial quantities of phosphate. These two ore types are separately crushed and are kept separate through copper flotation and magnetic separation, for recovery of magnetite, with the low Ti magnetite being shipped as iron ore. High phosphate tailings are pumped to Foskor, a government-owned phosphate plant nearby. The Palabora plant was originally designed in 1966 for 33, 000 tpd using two 54 in. by 74 in. Allis -Chalmers gyratories; two 7 ft (2. 13 m) standards; four 7 ft shortheads; and six grinding lines, each using one 1,200 hp rod mill and two 1,200 hp ball mills. A fifth short- head and one more grinding line were added later; and with flowsheet improvements, the capacity of the plant was increased to 59, 500 stpd. A further plant expansion involving a third 54 in. primary and two 32 ft by 15 ft (9.75 by 4.6 m) 9,000 hp autogenous mills and another flotation section will bring its capacity to 87,500 stpd in 1977. These two fully autogenous mills are constructed entirely out of doors near the primary crusher, and the ground ore will be pumped a mile to the concentrator by a five-stage pumping system. The Palabora ore is mined with 6, 10, and 12 7d (4.6, 7.6, and 9. 2 cu m) shovels and hauled to the crushers in 110 and 165 st trucks. Sixty-five ton trucks were originally used, but the crusher dump pockets were designed for larger units. Dump pockets, crushers, feeders, and take- away belts are offset in order to keep the two ore types separate. Centerlines of the crushers are only 43 ft (13. 1 m) apart; but, because of their being offset, maintenance room is ample. Initially, more carbonatite ore than foskorite was mined; but as the pit has deepened, this ratio has been reversed. The Palabora ore breaks in the pit with a large amount of oversize boulders; and, with the use of larger trucks, a splitter has been installed on one side of each dump pocket to protect the crusher spider. Smaller trucks dump on the opposite side. To accomodate the splitter, the pocket edge has been raised one meter and moved back one meter. Dust is collected through a special vent shaft between the crushers and the mantle relining area; but even so, two high-pressure water spray headers with nozzles are installed under the edge of the pocket at each dumping position. While only one truck dumps at a time, sprays from all four headers are used to suppress dust. Any leakage of water through the seal around the upper bowl of the crusher is caught by a circular trough under the seal and directed to a sump pump. At this point, there

Jan 1, 1978

By R. D. Coursen

Tin has been one of the very few commodities which has been covered by an international commodity agreement. It is the only metal so covered. The reason behind tin's prediliction for an agreement has been the inconsistency of the price pattern for tin during the entire 20th century. It is not surprising in view - of the wide and wild fluctuations in its price that tin has been called the Cinderella metal. An examination, for example, of prices in 1977 alone attests to the erratic behavior of the tin markets. The high was recorded on October 27 at M$1,895 per picul and the low on January 3 at M$l,314 3/8, on the Penang market, a spread in Malaysian dollars of $581 for a picul weighing 133 1/3 pounds. The first steps in international cooperation on tin were taken after the price bonanza of the First World War. Despite a lack of increased consumption, and in spite of the fact there was no shortage of mining production during the war, prices boomed. Shipping shortages and thinning stocks brought about a situation where in the U.S., industrial stocks were only 1/6 of what they had been in 1914. The boom busted early. In 1921 the tinplate industry of the world had cut its output in half and total world consumption of tin fell by 1/3. Tin producers became so concerned that they created what was called the Bandoeng Pool. It accumulated stocks held by countries now known as Indonesia and Malaysia, amounting to 28 percent of the combined production of the two countries and about 15 percent of the total world for 1921. The pool holdings were shortly exhausted and thereafter in the years 1924 to 1928, general boom conditions existed for tin.

Jan 1, 1978

By Howell IJ, Kirsopp R

In June/July 1981 Mount Isa Mines Limited was confronted with a crisis situation in the crushing operation of the Lead/Zinc and Copper Concentrators. Three crusher mainframes developed serious cracks in the upper rim area. The type of cracking indicated that major failure of these mainframes could be imminent. Operational crushers could not be sensibly inspected and it was therefore assumed that more than three mainframes were seriously cracked. The crisis was averted as described in the following text.

Jan 1, 1978

By D. R. Murray

A four-year study was carried out to determine the ability of coniferous trees to aid in the reclamation of uranium tailings at Elliot Lake. Five species were planted: white cedar, white spruce, jack pine, scotch pine and red pine. More than 570 bare-root, two-year-old seedlings were planted on bare tailings and in areas of established grasses. A further division was made between areas of coarse and fine tailings. Over-all survival and growth of the trees has been far below expectations based on previous experience with several varieties of grasses. The criteria for assessment have been per cent survival and yearly growth as determined by plant height. Pine was superior, with 68% survival when planted in bare coarse tailings, 45% for vegetated coarse tailings and 34% for vegetated fine tailings. Cedar had the worst survival rates at 49%, 14% and 7% respectively. No species survived on bare fine tailings. The survival and growth of the coniferous trees have been related to species, environmental conditions and tailings properties.

Jan 1, 1978

By Thomas M. Garland

During the rest of this century, the United States faces no more complex or challenging problem than that of assuring availability of adequate, secure energy supplies in general, and crude oil and natural gas in particular. This talk will present the bare facts concerning where we have been, where we are, and what we can expect, focusing primarily upon consumption and supply of crude oil and natural gas.

Jan 1, 1978