Search Documents

Ore samples generally require preparation before analysis. Serious problems can occur with contamination degradation and particle size effects. Both grinding element contammation and sample cross contamination havebeen bound to be related to sample hardness and operator technique. For best results with minerals relevant to the steel industry, the use of Siebtechnik-type mills required a combination of careful planning, short grinding periods and intermediate sieving of the sample. The results may be extended to most mineral, rock, and refractory sample preparabons.

Jan 1, 1978

Knowledge of true block grades is obtained from a mathematical model of an orebody, simulated with sample grades normally distributed and spatially correlated according io a spherical semi-variogram model.The superiority of kriging to the polygonal method of estimation is demonstrated on this modelled deposit by comparing the true values with the kriged and polygonal estimates obtained from sampling the deposit. Finally, selection of blocks of the deposit on the basis of the estimated values, shows that if kriging is used, what is predicted is largely mined, whilst if the polygonal method is used large biases can occur depending on the position of the cut-off grade.

Jan 1, 1978

Particles of a complex nickel sulphide concentrate (containing pyrite, pyrrhotite, pentIandite, and violarite as the major mineralogical constituents) were entrained in a stream of hot gas the temperature of which was varied from 500 to -1000°C. Chemical analysis of the particulates collected from the furnace was used to detect the rapid change in sulphur content which accompanied the ignition temperature jump. X-ray diffraction analysis was used to characterize the oxidized material.These techniques showed that ignition was dependent on the mineralogical composition and occurred over the temperature range 500-900°C. Pyrite ignited first in the range 500-600°C; pyrrhotite was the least reactivemineral and required temperatures in excess of 800°C for ignition. The nickel minerals <pentIandite and violarite decomposed before ignition and ignited at temperatures intermediate to those required for the pyrite and pyrrhotite. The ignition temperature for the pyrite was found to be independent of particle size and concentration of oxygen in the atmosphere.Ignition temperatures determined by the simulated flash smelting method were compared with the results of differential thermal analysis (DTA) measurements performed on the same concentrate. Temperaturesdetermined in the DTA test as corresponding to the start of exothermic activity were shown to be at least 100°C below those determined by the simulation test.

Jan 1, 1978

By Y. Serres

In the past, conventional reflection seismic techniques were not very successful when applied to typical mining exploration: they lacked resolution in the shallow range or were not cost effective. By combining a light earth tamper source, special geophones and field procedures, a stacking process of the returning seismic events using a microprocessor system, and a sophisticated sequence of adapted digital data processing, Mini-Sosie achieves high resolution in the 100-ft to 4000-ft range. Additional advantages result from the very quiet nature of the source and flexibility of the system. Although Mini-Sosie might be used in the refraction mode, or for well velocity logging, it has found its main applications with the reflection technique.

Jan 1, 1978

By J. C. White

A research study was conducted to devise a method for producing phosphoric acid directly from unbeneficiated Florida phosphate matrix. This research was performed as part of the Bureau of Mines, U.S. Department of the Interior, goals of improving minerals and metals recovery from domestic resources and of minimizing the environmental impact associated with mineral recovery operations. This report describes research in which unbeneficiated, dry, south-central Florida phosphate matrix was digested with sulfuric acid in a continuous-circuit, five-tank reactor to yield phosphoric acid and gypsum residue. Feed capacity of the reactor was 100 pounds (45 kg) of dry matrix per 24-hour day. When digestion was carried out at 185° F (85° C), acid filtration rates of up to 420 pounds of P20S per square foot per day were attained. Combined iron and aluminum impurities in the product filter acid were about 60 percent greater than values reported in commercially produced acid derived from concentrate. phosphate recovery was 87 to 90 percent of the phosphate contained in the as-mined matrix.

Jan 1, 1978

By Haukka M. T

A new low-dilution fusion method which has been successfully used for accurate determination of the major oxide components of silicate rocks, is applicable to rapid, accurate determination of trace or minor eiements in mineral exploration samples. Limit of detection is in many cases less than 5 ppm. Either rapid, approximate measurement and calculation methods (suitable for geochemical exploration), or more accurate methods (applicable to orebody evaluation studies) may be used.Rapid methods are described for nickel in rocks and sulphides containing 10 ppm to >2 per cent Ni, and for gallium. The rarely-determined element gallium is an example of a constituent which may be easily investigatedby XRF using the LiB02 fusion disc, which is a permanent, easily-stored analytical sample available for later rapid or accurate analyses. The method is applicable to over 30 elements at levels encountered in mineral exploration.

Jan 1, 1978

By D. Christofferson

This final report documents the cooperative efforts of the Engineered Systems Division and the Mining Equipment Division of FMC Corporation during performance of Bureau of Mines Contract H0252091. Improved operator compartments incorporating overhead canopies, logical arrangements of controls, and design features offering greater operator comfort were developed and retrofitted to the FMC 320A roof bolter and 6L shuttle care The vehicles were evaluated in underground operations at separate mine sites. The successful evaluation has resulted in incorporation of the designs as standard features of the 320A roof bolter, and the 5L, 6L, and 10L shuttle cars.

Jan 1, 1978

By K. B. Chaudhurl

The thermodynamics of the reactions taking place are examined with the aid of equilibrium diagrams for the Pb-O-S system. Based on investigations of chemical, mineralogical and differential-thermo analyses of intermediate products of different desulphuration degrees, an attempt is made to explain the mechanisms of the reactions in the smelting shaft of the KIVCET furnace. The differences between this and other direct lead smelting processes are demonstrated by these thermodynamic and kinetic considerations. Proceeding from these results, the practicability of direct lead smelting processes is discussed with reference to the composition of the primary feed materials to be processed. This comparison also considers the behaviour of minor metals, the products obtained and their characteristics in respect to further treatment. For assessing the operating costs, the over-all energy consumption is considered taking into account various price relations between electric energy and fuels/reductants. Based on the peculiarities of the various processes, an attempt is made to compare the necessary means of meeting the pollution control requirements. The paper concludes with reference to the criteria and problems involved in comparable evaluations.

Jan 1, 1978

The Kennedy Siltstone Open Cut provides graded rock for stope filling. Rotary drilling of 310 mm blastholes with a Gardner Denver GD120 is used, and the successful application of an equilateral triangular drilling pattern is described. Charging practices and the development of bulk slurry handling are outlined. Blast monitoring plays an important role in K.S.O.C. drilling and blasting operations. The proximity of nearby residential areas (1300 m) and the Mount Isa Airport (4500 m) necessitates special attention with regard to the minimisation of both air blast and ground vibration levels. The application and control of drilling and blasting parameters has had a direct bear- ing on success of the mining operations and also played an important role in reducing the disturbance to the community.

Jan 1, 1978

By Restarick C, Jowett A

A cylinder-cyclone system, fitted with a flow control valve between the cylinder and cyclone plus in some tests a variable cyclone spigot, has been used to achieve classifier separations at unusually coarse sizes relative to the diameter of the units used. The method has proved to be useful for low tonnage flows at low pulp density and variable feed rate. The system relies on use of a cylinder unit to reject excess water and fine particles, the amount rejected being adjusted by the flow control valve. The valve also adjusts flow rate and pulp density of feed to the cyclone unit, and can be adjusted to give a separation at a coarse particle size. The system has been used in connection with experiments on the pilot plant at Mount Isa, where a 76 mm system was used to classify feed to the lead secondary rougher circuit at sizes as coarse as 52 micrametres galena equivalent for split conditioning tests. Further tests have been carried out with quartz to assess the range of size separations Possible.

Jan 1, 1978

Heavy media separation serves to upgrade mill feed and reduce unit operating costs, allowing ores to be mined which could other wise be uneconomic. At the Aberfoyle mine at Rossarden in north-east Tasmania, a simple heavy media operation using a converted Akins screw classifier as a separating vessel, removes barren quartz from mineralised material. At the Cleveland mine at Luina on the west coast of Tasmania a more complex ore mix requires a versatile operation combining hydro-dynamic and static separation equipment to provide an efficient beneficiation circuit. The two operations are briefly described with a background of basic heavy media separ- ation practice.

Jan 1, 1978

Past President Shirl McArthur opened the meeting at 9:30 a.m. He called on the Auditing Committee to give its report. Stan Shubart, who checked the financia1 report of the treasurer, read the report. He asked that it be approved. A motion was made, seconded and carried. Shirl thanked all the committees for an excellent job in making this meeting a most successful one. Special thanks to Park Lamborn for a fine program and to Gussie Whiteside for all her efforts in behalf of the Institute. An increase in salary was voted for the secretary-treasurer. It was decided to return to Vail for the 1979 convention. The Resolutions Committee was called upon to give its report. Roy Coulson, Chairman, submitted the following: (I) RESOLVED, Whereas, in the year since the last convention of The Rocky Mountain Coal Mining Institute, the Institute and the coal mining industry have suffered the loss through death of the services of: O. F. Bridwell C. L. Book O. F. Lewis Frank Kolar O. H. Littrell L. B. Phillippi Weston L. Potter George C. Trevorrow

Jan 1, 1978

By Harold R. Wampler, John L. Bolles, Adrian J. Broderick

Phelps Dodge's 60,000 tpd Morenci Concentrator has been in operation since 1942. The integrating of process control applications into the concentrator began in 1972. A process control system is presently on-line controlling 30 primary grinding circuits and all reagent additions. The system consists of a centralized control room process control Computer, on-stream X-ray analyzer, on-stream particle size analyzers and an operator interface. This paper describes the process control system's development, control concepts and its influence on the concentrator performance.

Jan 1, 1978

By G. D. Andria

Contract J0275007 was to consist of a thorough two-phase statistical analysis of respirable coal mine dust data from USBM Contracts H0232061, H0232060, H0230029, H0230031, H0210050, and H0242013. Consequently, BCR cataloged and assembled relevant data items from these contracts and formulated procedures suitable for the evaluation. The selected procedure was a Multilinear Regression Analysis which related dust concentrations measured in the mine to other mine parameters. Under the first phase, a thorough analysis of the date from USBM Contract No. H0230029 was completed. Primary results from this analysis are as follows: (1) The five variables that significantly affect dust concentrations in the return behind the brattice are the spray system utilized; the distance from the face to the return brattice; the return airflow; the production rate; and the water consumption rate, in that order. These five variables describe about 85 percent of the total variation in the return dust concentration. (2) Results at the miner and jack-setter locations were somewhat less conclusive due to the fact that only 17 percent of the variation in dust at the miner could be resolved and only 48 percent of the variation at the jack-setter location could be explained. The decision of the sponsor was that these initial results revealed as much information as could be expected; thus, per instructions from the USBM, the second phase (analysis of the other five contracts) was abandoned.

Jan 1, 1978

Several primary ingot producers have introduced price changes for July. Howmet Aluminum Corp., Revere Copper and Brass, Inc. and the Anaconda Co, will increase late-July prices of 99.5 percent unalloyed aluminum ingot by 3 cents to 56 cents per pound, Prior to this, Kaiser Aluminum and Chemical Corp. had advanced June ingot values by 4 cents to 57 cents and Consolidated Aluminum Corp., 4.5 cents to 57.5 cents. Domestic merchants held June quotes at a range nearing 50-50.8 cents per pound. ANTIMONY Although NL Industries, since April of this year, stopped publishing prices for RMM and Lone Star antimony grade, values of domestically-refined antimony in alloy are being made available to industry, The current price of this material is $1.75 per pound of antimony contained in alloy, New York dealer-marketed metal was available in June at $1 -13-$1 .20 per pound. Important industrial uses of antimony are for flame retardants, storage batteries, chemicals, pigments, rubber, plastics, glass, ceramics and machinery.

Jan 1, 1978

By Barrie C. Butt

The opportunity for an exploration geologist to follow a successful exploration project through the feasibility, financing, construction, development and exploitation phase is rare. In addition, it is not often that the exploration geologist can be present during the mining of a deposit to explain why certain actions were taken or interpretations made and to find out how these interpretations turned out in actuality. At the Woodsreef chrysotile asbestos mine in New South Wales, Australia, mining has been in progress for six years and the writer has been intimately associated with the project during the five years of exploration and the six years of exploitation. The industry is possibly aware of the fact that the Woodsreef Mine has had major production problems, the majority of which have stemmed from the unique characteristics of the ore body and of the fibre. Because of these unique features, a large volume of research has been undertaken by Woodsreef and by other scientific organisations in Australia, England and Canada on the Woodsreef fibre. The answers to some of the problems have negated some semi-sacred concepts of asbestos ore milling and led to the development of new techniques, such as the adoption of microscopic fibre counts as a routine procedure; the modification of accepted evaluation procedures; the development of new machines for dedusting fibres, and to the recognition of a fibre with a unique milling behaviour pattern and, possibly, properties. The problems experienced can be divided broadly into those associated with the geology and those associated with the physical properties of the fibre. It is possible that the same features may manifest themselves in other deposits around the world, and if they can be recognised during the exploration stages a feasibility evaluation may be just that little closer to the actual.

Jan 1, 1978

A forecast of energy demand in the non-commu- nist world to the year 1990 is presented with com- ments on the expected effectiveness of conservation efforts in achieving more efficient utilization of energy. A forecast of energy supply for the same period is presented showing the contribution of oil, gas, hydropower, coal, and nuclear fuels, with brief comments on the factors constraining the rate of growth of non-oil energy supplies. The role of `synthetic fuels', i.e. liquid or gaseous fuels produced from coal, oil shale, and tar sands, is reviewed with brief discussion of factors affecting the development of this industry. In somewhat greater details, the growth of demand for oil by geographic regions is analyzed. Particular attention is directed to the source of the oil supplies which will be required. The anticipated rate of discovery of new oil reserves is discussed with comments on lead times required in the development of new discoveries in hostile environments such as the Arctic and deep oceans. The continuing importance of oil supplied from countries which are members of the Organization of Petroleum Exporting Countries (OPEC) is illustrated. Oil will continue to be the marginal ('balancing') source of world energy supply throughout the forecast period and although it now appears that oil supplies will be sufficient to balance the energy equation during the 1980s, little flexi- bility will exist to cope with unexpected growth in demand or slippage in supply. Prudent energy re- source management will require major efforts to stimulate conservation and also to stimulate the rapid development of conventional and new forms of energy supplies and changes in energy consump- tion patterns to utilize the new supplies. Because of the long lead times and the massive capital require- ments involved, governmental policies are needed soon which will stimulate conservation and which will encourage businesses to move rapidly to assure the energy supplies the world will require in the 1990s.

Jan 1, 1978

By Gordon O. Prickett

In two case studies we look at strategies of acceptance that the analyst can employ to gain entrance and to see his problem solution out to use. The first example comes from metal mines. The problem area was excessive usage and cost of wear parts in the concentrator and an atmosphere of crisis over frequent and unexpected breakdowns. The second case pertains to coal exploration. Better methods were being sought for representing coal quality in developing reserve tonnages. The first strategy is - Develop a detailed Human Impact Statement. The second strategy is - Write down in plain language with the keeper of the problem what he will consider as success in dealing with his problem.

Jan 1, 1978

Gravity concentration of tin at Renison Limited uses tables and spirals to treat the various coarser fractions produced from sulphide flotation tailing. An acceptable final tailing cannot be made from one pass over the tables and spirals and therefore the tailing from these separators is reground and combined with the sulphide flotation tailing as the feed to the classification section. The gravity section became increasingly overloaded in the years preceding 1976 due to efforts to maximize tin recovery to the gravity concentrate. In April, 1976, two 2DSV Reichert cone concentrators in series were installed to treat the table and spiral tail- ing stream, prior to regrind, to scavenge a small tonnage of hard, coarse low tin grade material for rejection to final tailing. Gravity section loadings were decreased markedly, allowing operator attention to be directed more to table performance than to spillage collection. An increase in mill throughput of approximately 15% was possible following the commissioning of the Reichert cones. The cones are currently operated to make the minimum tonnage of tailing consistent with reasonable- gravity section loadings.

Jan 1, 1978

By M. A. Trevits, S. W. Lambert

In this Bureau of Mines investigation, production was monitored for 1 year at over 30 coalbed gas-drainage boreholes located in Alabama, Pennsylvania, and West Virginia. Results indicate that the quality of data gathered from such wells can be improved greatly if potential problems are anticipated and prevented in the early stages of well production. Major water-monitoring problems include solids buildup, freezing, the presence of gas in surface waterlines, and improper pumping interval settings. Such problems may be avoided by incorporating in the original well design waterline filters, sand screens, separator tanks, and systems to automatically control pumping intervals. Problems related to measurement of coalbed gas flow include large quantities of water vapor contained in the gas, especially during winter months; freezing and subsequent obstruction of flow; sudden, uncontrolled release of gas pressure; and solids buildup in metering equipment. The installation of commercially available items, such as filters, separators, and insulation, and the thoughtful application of a basic knowledge of coalbed gas reservoir characteristics will prevent most production-monitoring problems.

Jan 1, 1978