Search Documents

By Kris Shukla

Noise and vibration produced by blasting generate curiosity and concern from neighbors. Experiments conducted in Sweden, Canada and U.S.A. have established that fine cracks in the plaster--the weakest part of building components--appear at a particle velocity of 4.0" per second or more. Taking into account the margin of safety, the safe zone criteria of 2.0" per second has been established.

Jan 1, 1978

By Robert P. Vinson, Kissell. Fred N., Edward D. Thimons

"The Bureau of Mines investigated the presence and extent of methane accumulations in mine roof cavities using a full-scale mine model. Methane was released at a constant rate into the roof of a cavity built onto a 700-ft wind tunnel. Two box-shaped roof cavities were used in the study: one had a volume of 114.7 cu ft; and the other had a volume of 57.3 cu ft. Methane concentration was measured at 28 sampling points in the cavities using 21 different combinations of gas emission rates and air velocities. Brattice hung in the cavity helped reduce methane concentrations without auxiliary ventilation. It was also found that the effective ventilation rate increased by a factor of 40 in the large cavity and by a factor of 20 in the small cavity when air velocity was increased from 100 to 600 fpm.INTRODUCTIONAny location in a coal mine where 5 pct or more of methane is present constitutes a potential site for an explosion and roof cavities are likely locations. Unfortunately, little is known about the buildup of methane in roof cavities. Some research has been done using scale models where no air flows past the cavity so that methane disperses only by diffusion (5) 4 a rare situation in mines.No known cavity-model investigations have been made that simulate air and methane flow conditions normally encountered underground. These Bureau of Mines studies were undertaken to determine the extent and manner of methane buildups in coal mine roof cavities with air velocities in the range normally found in coal mines and with various methane emission rates."

Jan 1, 1978

By Gordon C. Rausser, Michael D. Boehlje, Richard A. Levins, John A. Otte

Changes in SO2 emission standards will not only influence the cost of supplying energy demands from coal, but also the competitive position of various production regions and the method of mining (surface vs. underground). A multiperiod interregional competition model was utilized to evaluate the interactions between mining capacity, new mine development, coal reserves, mining, processing and transportation costs and equipment availability and SO2 emission standards. The empirical results indicate that not only will costs increase dramatically, but production in eastern as well as western regions that have low sulfur reserves will also increase as sulfur standards become increasingly more strict. Implications of the adjustments in the location of coal mining activity for the processing, transportation, and capital goods markets are also presented.

Jan 1, 1978

By Henry C. Knight

A number of improvements in the techniques of budgetary control have been developed in the 1970's. The most significant of these is zero-base budgeting. This procedure is a marked improvement, because it overcomes some of the key weaknesses inherent in most traditional approaches to budgeting. It incorporates techniques and disciplines which improve the quality of both the budgeting effort itself and the documents that most senior managers will need to evaluate. The end result is a budget that establishes and improves cost effectiveness. This budget is based on resource allocations using cost-benefit criteria and on a system of prioritization for making funding choices. Zero-base budgeting is applied only to costs and expenses that are not conducive to control using industrial engineered standards. Therefore, the benefits attributed to zero-base budgeting will only hold true for administrative, selling, exploration, safety, fire protection and overhead, and other indirect types of costs and expenses. It is in this context that the question of its attractiveness for the mining industry is dealt with.

Jan 1, 1978

By A. Bruynesteyn

The results of a 2 phase evaluation program designed to determine the amenability of an oxide ore from the Butte, Montana mine of the Anaconda Company to a sulfuric acid leach is presented. In the phase 1 preliminary evaluation, using roll tests and percolation leaching in small columns, it is shown that the ore is highly extractable at low acid consumption ratios. In the phase 2 confirmatory tests in large columns on l-l.5 tons of material, the amenability of the ore to the leaching process is proven and pregnant solution grade profiles from planned commercial heaps established.

Jan 1, 1978

By John T. Metcalf

The assembly procedures for nine different wire rope terminations used in the mining industry are presented in a format and manner to facilitate training and to provide points where inspection of the termination should be performed. The nine terminations addressed are: Flemish Loop with Steel Sleeve & Thimble, Flemish Loop with Steel Sleeve, Wedge Socket, Swaged Socket, Turn Back Loop with Sleeve & Thimble, Thimble Splice with Four Tucks, U-Bolt Clip & Thimble, Zinc Poured Socket, and Epoxy Resin Poured Socket. The manual was prepared to be used primarily for field type mining operations or training where high capacity machinery is quite limited. It is nut the intent of this manual to suggest that the procedures presented are those to be used by manufacturers or other commercial enterprizes. A different set of procedures may be more appropriate where ideal space and equipment resources are available. The assembly procedures were derived from standard industrial practice, manufacturer's recommendations, and the open literature on the subject. These same procedures were used to prapare test specimens for an extensive series of pull and axial fatigue tests. The results of these tests indicate that these procedures are satisfactory in all respects. This manual is to be used as part of a complete training program. Although a brief glossary is included, there has been no attempt to make this a primer on wire rope. The selection of wire rope termination hardware, like the selection of the wire rope, is a subject not covered by this manual. The reader is cautioned that there are various sources for such hardware and this selection must be done carefully.

Jan 1, 1978

By Colin G. Wilson

This paper considers the heavy liquid laboratory tests used to determine the amenability of a potential ore to the heavy media process. The results of the laboratory testing are correlated to actual plant performance and establish design parameters for the heavy media process. These parameters are used in the development of the metallurgical flow sheet and in the sizing of equipment in the metallurgical plant design.

Jan 1, 1978

I must tell you at the outset that I come to this conference deeply disturbed at the `role of Government in international dealings in mineral and energy resources'. I am disturbed by the confusion that now passes for policy. I am disturbed by the short- range view of critical problems taken by a majority of Governments. I am equally disturbed by the even shorter range of view taken by a growing army of industries. Many of them clamour for Governments to solve their problems in a specific way, with little regard for any other sector but their own-and with even less regard for the fact that every time a Government takes over some of their responsibilities they surrender some of their freedom. I would not say that longer range views don't exist. But I would say that they don't prevail at the present time. Instead, we are seeing the con- stant development of many policies for individual problems which don't tackle the fundamental causes. We must get back to basics without delay.

Jan 1, 1978

By César Jaime Fernández

El presente texto señala los conceptos de "rentabilidad" y "productividad" en la empresa pública y privada. En ese sentido, una actividad es rentable cuando muestra utilidad y desde un enfoque general, económico y social, una empresa es rentable cuando genera provecho o beneficio a la sociedad. Ambos aspectos son coincidentes y sólo presentan alguna diferencia técnica en su cuantificación. De otro lado, se muestran criterios de rentabilidad y productividad y la rentabilidad global de la mediana minería.

Jan 1, 1978

The Pinto Valley, Arizona, plant of Cities Service Company is one of the newest copper producers in the United States, having started production in 1975. It is located a few miles west of Miami, Arizona, on the site of the Castle Dome Mine, a World War II operation which was shut down and its mill later moved and renamed the Copper Cities plant. The Pinto Valley concentrator uses six 18 ft (5. 5 m) diameter by 21 ft (6.4 m) long, 4000 hp, single-stage ball mills, taking crushed ore from four 7 ft (2. 13 m) standard and eight 7 ft shorthead crushers. It has a design capacity of 40,000 stpd but has higher tonnage capability for an expanded concentrator. The copper porphyry-ore is mined by two 15 yd and one 20 yd shovels (11.5 and 15.3 cu m) and is transported to the primary crusher by 150-ton trucks. The dump pocket is relatively shallow (14 ft or 4. 27 m deep); and because of the width necessary for the 150-ton trucks, it was designed to use the ore itself instead of manganese steel as an abrasion- resistant lining, although a heavy steel cap protects the dump pocket top edge. The pocket has a capacity of 300 tons of ore. Water sprays under the dumping positions direct a fog toward the truck being dumped for excellent dust control. Breaking of oversize is done by a hydraulic impact breaker mounted on a hydraulically operated articulated arm situated at the side of the dump pocket. Again because of the shallow pocket, no splitter is used to protect the spider of the 60 in. by 89 in. Traylor gyratory crusher, which is equipped with a hydroset mechanism. Crushed ore at 8 in. (203 mm) drops into the 360 st surge chamber lined with AR plate and then is fed directly to the 60 in. (1.52 m) stock- pile conveyor by an 84 in. by 20 ft (2. 13 m by 6.1 m) four-speed apron feeder at a rate of up to 4000 stph. Early in 1977, Cities Service will replace the four -speed electric drive with a hydraulic pump and motor with infinitely variable speed. They are also studying the replacement of the apron feeder with an 8 ft wide (2.44 m) belt feeder similar to those at Similkameen and Palabora. Peak crushing capacity would then be increased to 5000 stph. The AR plate in the crushed ore pocket was installed in large, rectangular sheets which required much less embedded metal to hold it in place than would the more conventional, smaller arid square pieces of cast manganese steel. For duty in the crushed ore pocket, where wear is not severe, the AR plate is a satisfactory material. The new Palabora Figure-8 crusher also uses this design.

Jan 1, 1978

By Andrew T. Zador

The growing demand for energy combined with the need to protect and preserve the environment have become prime considerations in the design of efficient coal handling ports and their associated stockpiles. The transportation system is analogous to a connected chain which originates at the mines and terminates at steel mills or power plants, in which the port and the stockpile reserves are a vital link. Railroad transportation costs can be minimized by rapid discharge of the cars which, in turn, requires that an adequate stockpile system be available. Ocean transport costs can be minimized by having an efficient high capacity ship loading system and sufficient quantities of coal on hand -all of which also requires an efficient stockpile system to meet shipping demands. The connector between the two modes of transportation, therefore, is the port stockyard. It is here at the interface that optimization of land utilization and materials handling equipment results in a total transportation chain that can operate as a smooth efficient system. Multiple origins of coal require the simultaneous handling of large quantities of coal of many grades. Railroad transportation logistics often limit and define the incoming arrival patterns and limited rolling stock often require priority treatment for railroad operations. The physical limitations of prime ocean frontage require that coal stockpiles be built close to residential or industrial areas which entail strict environmental controls. Large capacity, enclosed coal stockpiles for ocean shipping have not yet been considered feasible but may be forthcoming in the near future. Several have been analyzed.

Jan 1, 1978

By A. Gene Collins

The demand for lithium may increase because of its potential use id lithium batteries and in the generation of electrical power by fusion. Therefore, lithium abundance in some United States oil-field brines was surveyed. Oil-field brines from numerous locations were found to contain more than 100 mg/l lithium and several exceeded 500 mg/l. An area of 25,000 km2, with a reservoir thickness of 60 m, an effective porosity of 5 percent, and a brine with a specific gravity of 1.2 containing 100 mg/l of lithium, contains about 0.75 x 106 tonnes (1 tonne = 1 metric ton = 1,000 kg) of lithium in 7.5 km3 of brine. It is postulated that the brines were enriched in lithium by lithium-rich spring water or lithium leached from volcanic rocks followed by evaporation sequences.

Jan 1, 1978

By William G. Pariseau

A design procedure for the quantitative estimation of support load requirements in underground mines is presented. The central problem in the design of mine support is one of es¬timating a maximum load that the ground will exert on the support in the coarse of mining. The distribution of stress around mine openings changes as mining progresses. At the time of support installation, the support load is essentially zero. With the passage of time and advance of the face, ground motion loads the support. The finite element method of analysis provides a simple quantitative technique for simulating the effects of mining and face advance on support load requirements. In particular, the maximum support load can be estimated by the proposed design procedure.

Jan 1, 1978

By P. Kawulka

An integrated pilot plant for the development of the S-C Copper Process was constructed at Fort Saskatchewan in 1975 and operated in 1976. The pilot plant was designed to treat 9 tonnes per day of a pyritic copper concentrate. A demonstration run conducted during the last quarter of 1976 averaged 90% on-stream time, and confirmed that the process is operable as a stable and integrated unit. The paper describes the parameters and equipment developed for thermal activation of chalcopyrite copper concentrates to make them amenable for the dissolution of iron and zinc, and their subsequent separation and recovery. The resulting high-grade copper sulphide was leached with return electrolyte and oxygen to extract 98.5% of the copper into solution. The copper was electrowon at 650 amps per square metre from purified solution, to produce cathodes analyzing 0.1 ppm Se, 0.1 ppm Bi, 4 ppm Pb and 10 ppm S. The electrical conductivity was >101% lACS and the spring elongation value [ ]350 mm. Elemental sulphur and gangue are removed from leach residues to make a concentrate containing over 95% of the silver and gold and most of the unleached copper. Conventional construction materials such as stainless steel, titanium, Hastelloy, acid brick, rubber and plastics performed well. The containment inherent in hydrometallurgy provided high standards of hygiene and safety.

Jan 1, 1978

By B. J. Moore

This publication contains analyses and related source data for 256 natural gas samples from wells and pipelines in 17 States. All of the samples were obtained and analyzed during calendar year 1977 as a part of Bureau of Mines investigations of the occurrences of helium in natural gases of countries with free market economies. This survey has been conducted in the United States by the Bureau of Mines since 1917. In late 1965, the survey was expanded to include foreign gasfields. The analyses published herein were made by mass spectrometer and a special helium analysis apparatus, which are described in Bureau of Mines Bulletins 4862 and 576.3 The results of the investigation of the occurrences of helium are published annually to make the information available as soon as possible to the gas industry and the public in general. Nineteen previous publications have presented the results of 11,317 gas analyses prior to 1977. The first three, Bulletins 486,4 576,5 and 617,6 contain analyses and related source data on 5,218 gas samples collected from 1917 through 1960. The other 16

Jan 1, 1978

By Frederick C. Trutt

A guide to the utilization and development of extensions and modifications to the APL Mine-electrical-system Load-flow Program is presented. These modifications include the development of algorithms to minimize computational operations within the iterative-solution techniques, as well as minimization of the number of required iterations. Extensions to the load-flow program include the development of algorithms for the calculation of balanced faults, simplified specification of fault parameters, optional inclusion of pre-fault currents, and an alternate-solution technique.

Jan 1, 1978

By M. Savich

A graphical method has been developed for the evaluation of the U.S. Occupational Safety and Health Act Noise Exposure Index and the Equivalent Continuous Sound Level. The method makes use of a noise survey form and a mechanical integrator with two sliders, and is less tedious and susceptible to error than alternative methods. The graphical method is adaptable to various codes for noise exposure and may be used with any instrument that measures noise level. One example of its application to a practical situation in a Canadian mine is given to demonstrate the procedure .

Jan 1, 1978

By Richard W. Watson, Julius Roth

The Bureau of Mines has recently completed a contract study of the hazards associated with surface mining.! Part of this effort involved an analysis of surface mining accidents associated with blasting activities. For this purpose, 71 reports of accidents investigated by the Bureau of Mines or the Mining Enforcement and Safety Administration (MESA), covering the period from 1962 to 1976, were collected and analyzed. In addition, blasting accident frequencies for the period 1973-1976 were extracted from the central computer files maintained by the Health and Safety Analysis Center (HSAC) in Denver, Colorado. This paper presents a preview of the findings, which are treated in more detail in the final report.

Jan 1, 1978

By Barry W. Klein

The U.S. economy was considerably stronger in 1976 than in 1974 or 1975. Real gross national product (GNP) rose sharply in the first quarter of 1976 and then increased at a more moderate rate for the remainder of the year. The unemployment rate fell until June and then increased for moat of the remainder of the year, finishing at the same rate as it had started the year. The inflation rate continued to decline in 1976. Reasons for the relatively low rate (compared with those of 1974 and 1975) included small increases in food prices and only moderate increases in energy prices. Total U.S. output measured in terms of GNP increased 11.6% in 1976. Real GNP in 1972 constant dollars rose 6.2%. Inflation as measured by the implicit price deflator increased 5.1%. In real terms, gross private domestic investment for residential structures rose 22.7% in 1976 after declining 14.7%a in 1975; State and local Government expenditures increased 1.4% in 1976; and personal consumption expenditures for services rose 4.5%. The Federal Reserve Board (FRB) index of industrial production increased 10.2%.

Jan 1, 1978

By Norman A. Jull, A. L. Mular

Fundamentals of cyclones are reviewed briefly, where a typical cyclone is considered. Graphical cyclone data available in the literature have been converted to mathematical equations for convenience. Preliminary selection and design procedures for both cyclones and pumps are provided, and a sample calculation for a hypothetical grinding circuit is covered in some detail. In general, cyclone and pump suppliers should be consulted for definitive design purposes. Some cyclone suppliers currently employ digital computers for definitive design to ensure greater accuracy.

Jan 1, 1978