Search Documents

By G. E. Agar

This paper deals with the prediction of locked cycle flotation results from data developed from individual batch tests. A postulate is made that the distribution of material in a separation stage is determined by the chemical conditions and the flotation time and that this distribution can be characterized by split factors which are constants for a fixed set of conditions. With this premise, it is demonstrated that a steady-state balance can be calculated for a circuit. Although the necessary equations can be solved algebraically, a computer program was written that uses an iterative technique to arrive at the steady-state balance. The program is written so that a variety of circuits can readily be simulated. A number of examples are examined to demonstrate the validity of this simulation procedure. The sensitivity of the material balance to changes in the split factors was examined. Data developed from different flowsheets are presented on sulphide ores, on copper-nickel separation and on silver flotation.

Jan 1, 1978

By Syd S. Peng

According to accident statistics (l, 2), roof fall accidents occur quite frequently at the intersections of underground? openings and account for up to 30% of the roof fall fatalities. But this figure will certainly go up considerably if roof falls not associated with any fatal accident are included in the analysis. Unfortunately, nonfatal roof falls are seldom documented. In the underground coal mines, there are two types of entry intersections. One is the three-way (V type) and the other is the four-way (T type) intersections. A three-way intersection occurs whenever the mainline track haulageway turns at an angle into a section haulageway. The four-way intersections by far the most common type in the U.S. under-ground coal mines are formed by the intersections of two entries which are oriented perpendicular to each other or by the intersections of entries and crosscuts. However, crosscuts are frequently driven at an angle to the entry to facilitate machine movements. The four-way intersections formed by this method of crosscut development are angled. At the intersection of two underground openings, the diagonal roof span is wider than the width of each individual opening. This is one of the major reasons why roof falls occur more likely at the intersections than in the entry between pillars. Consequently, special intersection support plans are usually employed (Figs. 1 and 2) for intersections. The most popular practices are to decrease roof bolt spacing 1 ft. less than or to increase roof bolt length 1 to 2 ft. longer than those employed in the entry between pillars (3). The increase in bolt length or decrease in bolt spacing can be applied to all of the bolts in the intersection or employed only for the strategically located bolts depending on the individual mine practices. These rather generalized practices seems to be adequate for some areas but in many cases inadequate for others. Occasionally, the neighboring two lines of chain pillars are staggered such that the crosscuts in one row of chain pillars face the centers of the chain pillars in the neigh-boring rows. This layout forms T-type three-way intersections which are also inadequate for most weak roofs (3, 4). A study was therefore initiated to develop special techniques for intersection supports. The first phase of the study was the analysis of the stress fields for the underground entry intersections. A three-dimensional stress analysis was necessary for this purpose. Unfortunately, the three-dimensional problems of complicated boundary conditions are beyond the existing analytical methods. The three-dimensional finite element method (FEM) was therefore employed in this study. In the analysis, square pillars of 40 feet wide and an entry height of 8 feet were assumed while entry widths varied at 14, 20 and 26 feet. This model was selected to simulate the mine where roof falls data were collected. The second phase of the study was the collection of field data. The sizes of the roof falls including heights, lengths and widths were collected and analyzed. In the third phase study, the results of the first and second phases were compared and discussed. The analysis of field data revealed an arching zone within which roof falls occurred. The arching zone above an entry obtained empirically was compared with the calculated stress contours. Assuming that the bolts must be anchored in the rock strata outside the arching zone, the preferable systems of bolting were proposed. Also the amount of pretension required to inhibit sliding between layers was discussed.

Jan 1, 1978

By Welby G. Courtney

The Bureau of Mines conducted a field test program in the Pittsburgh coal seam to investigate the effect of water sprays in the suppression of respirable dust being formed while cutting with a continuous-mining machine. Emphasis was given to the location of spray nozzles on the top and bottom of the cutting boom. Results showed that (1) sumping caused about 60 percent of the dust escaping the face area, and shearing and loading caused the other 40 percent; (2) during sumping, top and bottom sprays were equally effective in dust suppression and reduced dust ~13 percent; (3) during shearing and loading, bottom sprays reduced dust 61 percent and were about 50 percent more effective than top sprays; (4) the combination of top and bottom sprays was slightly more effective than the separate systems, but water consumption increased 60 percent; and (5) inclusion of throat sprays decreased dust reduction by removing some of the water from top and bottom sprays where it was more effective.

Jan 1, 1978

By Al Gagnon

Since start-up in 1972, many circuit problems have been encountered, most of which were related to the abundance of fines (-28 mesh), which the circuit had not been designed to treat. The major problems associated with the original circuit included excessive loss of magnetite, reduced throughput during periods of a high proportion of fine coal in the plant feed and low yield in the fine coal circuit. This paper outlines the coal processing circuit at Fording Coal Limited as it exists today, with emphasis on the changes to the original fine coal treatment circuit.

Jan 1, 1978

Disseminated gold mineralization in the Vunda River area 12 km SE of Lautoka in Viti Levu occurs sporadically in shoshonite volcanics within an alteration area of some 6 km2. No definite intrusions have yet been located though possible intrusions occur toward the centre and on the eastern margin of the area. The nature and distribution of alteration suggests the presence of a co-magmatic mineralizing stock just below the surface.The gold occurs within close spaced fractures and occasionally around the c1asts of breccia and agglomerate.Various types of alteration compatible with porphyry mineralization occur, but to date show no zoning or defined correlation with incidence of gold which occurs in various alteration facies.It is suggested that the gold and trace copper mineralization at Vunda arises from the sub-volcanic intrusive phase (monzonite) of the Sambeto shoshonite (5 m.y.) and is part of an E-W zone of porphyry-type mineralizationtrending easterly to the Kingston porphyry copper deposit at Navilawa.There is a close similarity between the Vunda mineralization and some of the porphyry deposits of alkali affinity in British Columbia, Canada.

Jan 1, 1978

By Ed Ramsay

The Kerr Addison process involves the cyanidation, flotation, and roasting of graphitic gold ore. The grinding and treatment section of the present mill has at the present time a capacity of 1400 stpd and the precipitation section has a capacity of 6000 stpd. The grind is maintained at 80%, -200 mesh, and a gold recovery of 92% is obtained in the cyanidation circuit. With flotation and roasting, the overall gold recovery is increased to 98%.

Jan 1, 1978

Underground mechanized excavation in New Zealand has become more commonplace in civil and mining applications during the last three years. At one stage up to seven Dosco Road- header machines were being used on different projects around the country. The Huntly West Mine Drifts inclined at one in four were by far the most severe grade conditions that the machines were subjected to; however, other operations posed their own particular problems for the machines. Two major interrelated factors became evident as soon as the machines commenced at Huntly. These were traction problems on the grade and control of water, particularly on the invert.

Jan 1, 1978

By James R. Aggson

This Bureau of Mines report describes floor heave ground control problems that have been encountered in a new underground coal mine in West Virginia. Previous experience in the coal seam, the results of physical property investigations, and in situ rock stress determinations are discussed. The apparent cause of the ground control problems is the existence of a high, biaxial, horizontal stress field coupled with a floor member that has time-dependent deformation characteristics, A theoretical analysis of the failure process is developed. The analysis is assisted by finite element techniques. Mine design recommendations based on this analysis are presented.

Jan 1, 1978

By Lawrence A. Browning

In recent years, there has been a growing realization of the importance of ground water as a national resource and increasing concern that this resource be properly managed and protected from a variety of pervasive practices that endanger it. Aquifers have been adversely affected in every region of the country. In dealing w.ith the underground water program, EPA will have the following objectives: to protect human health, and to protect and conserve an important national resource. In pursuing these objectives, EPA will take economic consequences and other national objectives (e.g., energy) into account. EPA intends to pursue these objectives in full partnership with the States. Generally the States should retain the lead in protecting ground water.

Jan 1, 1978

By A. I. Johnson

The pegmatites of the Black Hills of South Dakota are the coarse-grained differentiates of the Harney Peak Granite. The Harney Peak Granite was intruded into the Pre-cambrian schist and quartzites and resulted in the Black Hills uplift. In the outer adzes of the granite intrusion occur the pegmatites. In the zoned pegmatites, representing the most highly differentiated portions of the parent magma, occur most of the minerals produced from pegmatites. These are of economic importance and they are the subject of this paper. The various mineral products will be taken up separately.

Jan 1, 1978

By C. L. de Jongh

Fracturing of the rock caused considerable difficulties during the boring of a deep-level tunnel in hard rock. A pilot bore was suggested as a possible means of reducing the effect of the fracturing, and this possibility was investigated theoretically by means of a three-dimensional elastic stress analysis. Failure criteria were applied to the results of this analysis, and it was found that fractures predicted by the use of a simple criterion of limiting tensile macrostrain criterion agreed remarkably well with in situ observation. It was concluded that fracture could not be avoided and that a pilot bore was likely to aggravate tunnelling conditions.

Jan 1, 1978

By D. Hodouin

Jan 1, 1978

By P. B. Altringer

The Bureau of Mines conducted laboratory tests to develop a process for recovering a marketable grade of tungsten from the brine of Searles Lake, Calif. The brine contains only 56 parts per million of tungsten (70 ppm WO3). Using ion exchange resins synthesized by Bureau chemists, 98 percent of the tungsten was extracted from the brine and 92 percent of the tungsten vas recovered as a marketable iron-tungsten concentrate containing 44 percent tungsten as tungsten trioxide. Although major technical problems have largely been resolved, research is progressing to escalate testing in a process investigation unit to provide more reliable data for an economic appraisal.

Jan 1, 1978

By S. Stone

Because of problems encountered with conventional timber supports, a system of concrete sausageshaped support pillars was tested. The pillars are 3 m long, 0,6 m wide, and between 70 and 80 cm high (the height of the stoping width). They consist of bags filled with a grout of cement (slagment and sand in the ratio of I :2, and are installed in a staggered pattern 6 m apart on dip and 2 m apart on strike. These support packs have proved successful, and, although they cost more than the timber supports formerly used (R4,63 per cent are supported as against R2,26 for the conventional timber pack), their use is felt to be justified when account is taken of the costs of lost production and low productivity due to the bad hangingwall conditions that occurred with the conventional system.

Jan 1, 1978

By Bernhard Schwab

A popular rule in the mining industry is that a property should only be developed if average unit production cost is less than a given proportion of the estimated long-run price of the mineral. This paper provides a comparative analysis of the average cost approach (ACA) with the use of net present value (NPV) as an investment criterion. It is concluded that the ACA is an easily understood and easily applied rule of thumb which may serve as a rough first screening device, for example in the early stages of deposit exploration. Its operational convenience is at the expense of accuracy and validity, and the NPV provides a sounder method of making decisions, especially in the case of marginal deposits.

Jan 1, 1978

By Wylie A. W, Mathew PJ

Bulk density and grade were determined on a variety of ore samples from the Mount Tom Price iron ore mine and the interrelationship between these properties and porosity deduced.Variable porosity is responsible for the wide scatter of data points and low accuracy of prediction in the grade of a single sample from grade/bulk density relationships.However, with a sufficient number of such data points, as from a nuclear geophysical borehole logging operation, the mean ore grade in an exploration-type drill hole (~63 per cent Fe) could be determined by regressionanal~sis with 95 per cent confidence intervals of approximately ± 1 per cent Fe. From the same logging operation, utilizing core data for calibration of the probe, the -mean fractional porosity for the drill hole (0·19 ± 0·016 at 95 per cent confidence interval) was deduced. This is less accurate than the corresponding result obtained on core material in the laboratory (0·20 ± 0·005).The range of porosity was from 0·08 for dense, high grade sectIOns of the ore, to 0·28 for friable ore of high grade or goethitic ore of lower grade. Shale band porosity ranged from 0·15 to anomalously high values of 0·48 believed to be caused by leaching of iron minerals from the shale. Porosity values for the iron ore component of the deposit are comparable to those found for the Cockatoo Island (W.A.) mine, and for sections of the Krivoy Rog (Ukraine) iron ore deposit of the Soviet Union.

Jan 1, 1978

By N. C. Joughin

Progress during the last two years in the Chamber of Mines programme for the development of mechanized stoping methods is reviewed, and advances in the basic technology are outlined. Specifically. advances in the understanding of rock fracture around stope faces. in rockbreaking techniques, in rockhandling techniques, and in engineering are described. The state of development reached with mining systems based on cutting, impacting. and blasting is also described.

Jan 1, 1978

By Dale C. H. Nevison

One of the most intensive of material rivalries is the confrontation between zinc die castings and plastic injection moldings. Pressed hard by the plastics industry, zinc die casters are learning how to make parts with less material yet without sacrificing quality. The key to this new trend is the technique of Thin Wall die casting. The obvious benefits of Thin Wall are lighter weight and lower cost. Again, obviously, these are the very selling points that put plastics into many appliance and automotive parts formerly made of zinc. One of the factors that has been most conducive to the outstanding growth of plastics has been the increasingly prevalent concept that "adequate" properties are sufficient, especially if there are cost advantages. Most of modern design today is oriented around the reasonable life of a product, rather than indefinitely extended life. This is simply an acknowledgment of the existence of a design environment that pervades many areas, reflecting the life-cyclic desire for change. Too often, so-called "weight-saving" materials end up being very costly - not only in production, but in durability and dependability. Change for the sake of change usually doesn't effect a change for the better. In the majority of cases, the best bet is to design in traditional materials and minimize the material needed, while maximizing the efficiency of the production process. Component prices of products to be produced from either plastics or zinc must be studied in detail to determine which material will produce the lowest cost of manufacture. It is not uncommon for two parts, similar in appearance at a casual look, to have a considerable difference in energy requirements and production costs. Detailed cost estimates of the advantages of each material should therefore be prepared for zinc and plastic parts before the final design and material selection decisions are made.

Jan 1, 1978

By Thomas S. Jones

This Bureau of Mines publication reviews characteristics, manufacture, and uses of natural and synthetic iron oxide pigments. Supply and demand trends within the domestic industry and in foreign trade are presented for 1955 through 1976. Iron oxides are expected to continue in demand for traditional uses, and if anything, to be favorably affected by technological developments. Imports have been significant in relation to domestic production, most notably for synthetic oxides from West Germany and Canada.

Jan 1, 1978

By B de Raadt

After discussing mechanisms of collapse for the explosive demolition of towers in general and cooling towers in particular, author comments upon a blasting operation in which four cooling towers were involved. The intention of this paper is to present reliable parameters, generally valid for the explosive demolition of reinforced concrete cooling towers.

Jan 1, 1978