Search Documents

By Bjorn Engsbraten

Explosive charges have been fired under defined conditions in a closed tunnel. The explosives have either been detonated in a steel tube or a single borehole. In the latter case dimensions, -loading density and confinement have been chosen to correspond to common practice.

Jan 1, 1980

By Joseph Cervik

Methane drainage methods can be broadly classified as surface or underground. Surface methods make use of vertical and slant holes. The underground method discussed in the present paper involves horizontal drilling from shaft bottoms and from locations along the periphery of mines. Every foot of hole drilled in coal from under- ground locations is productive and gas flows increase as hole length increases. Therefore, underground techniques have a great potential for producing large-volume flows of methane. Pumps to dewater the horizontal holes are not necessary because gas pressure forces the water out of the hole. Methane can be recovered through the use of a simple and inexpensive gas-water separator. Hydraulic fracturing, which has been used successfully to stimulate gas flows from vertical holes, has not proved practical in the case of horizontal holes.

Jan 1, 1980

A review of the motivation of personnel in the open cut mining industry. The effect of social, geographic, environ- mental, organisational, union and other factors on employees' motivation as assessed from job experience and from an attitude survey. An appraisal of where we should be heading and what influence management can have on the motivation of employees.

Jan 1, 1980

By Etienne Simode

When a fire breaks out in a mine access road, the hot smoke, due to heat transfer with the surrounding strata, progressively cools as it moves forward. Depending upon the resulting temperature distribution, the density of the fluid changes. This change will bring about: Firstly, a variation in the resistance of the roads, a static factor which will affect ventilation flow rates; Secondly, the appearance of extensive aerodynamic driving loads in the vertical and angled roads, a dynamic factor which can have an extensive impact on ventilation. Because of the appearance of combustion and distillation products, the vaporization of water, which wets the timbering and strata, and the expansion of gases, fluid rates can at times be increased tenfold in the area of the fire. These disturbances may cause explosions and ventilation inversions, which fill other working areas with smoke toxic to workers, and which can come up upon rescue teams from behind. Due to the progressive heating of the surrounding rocks, which will slow down heat transfer, these dangerous conditions change over time. At the Lorraine Basin Coal Mines, programs have been set up and employed for the computer simulation of these phenomena over time. They serve to anticipate or to understand such phenomena, the input data being the characteristic parameters of the mine ventilation network, the operating curve of the main fans, and measurements or estimates of some temperatures. Two programs, employed together, have been developed for these studies: One program, called RESO, calculates the distribution of flow rates and pressures throughout the entire network; The other, called FEUMIN, determines smoke temperatures over their entire path.

Jan 1, 1980

By William Paul Robinson

I would like to first summarize the relevant health information relating to the workers and general populations around uranium mining as a basis for understanding the hazards associated with these operations and their available remedies. This discussion will summarize the literature on Radon and its daughters, among the most toxic uranium decay products. Second, I will discuss waste handling in the uranium industry: past, present and future, discussing exploration, mining, and milling and the volumes of water and solid and gaseous wastes which are associated with these various phases of uranium operations. This paper will also include a discussion of the various past and present materials handling technologies and their responsiveness to the concern for uranium waste isolation. I will then conclude with a summary of recent modifications in the relevant standards as applied to uranium mining and milling. Joseph Wagoner, a research epidemiologist with the U.S. Public Health Service has summarized the literature on uranium mining and its health effects in his written testimony as a commissioned witness in British Columbia Royal Commission of Inquiry into Uranium Mining in January of 1980, entitled Uranium, The U.S. Experience: A Lesson in History.1 Briefly summarizinq his report, as early as 1546, miners of uranium bearing ores in Central Europe were reported to have unusually hiqh frequencies of fatal lung disease2. As early as 1879, the real nature of pulmonary disorders among these miners was first diagnosed to be malignant neoplasia or lung cancers. Of 655 miners dying between 1875 and 1912, 40% or 276 of these Central Europe miners died of lung cancer.4 By 1939, it was reported that lung cancer mortality rate for miners in these Central European mining districts was several times (9.7 per 1000) higher than that for similar populations in Vienna, Austria (0.34 per 1000). Thus, before uranium mining began in the U.S., there was a considerable body of information linking uranium mining to lung cancers. The U.S. experience can be summarized in Table 1 also from Wagoner's B.C. Testimony.1 This table shows that through 1978, 205 respiratory cancer deaths have been observed among white underground uranium miners in the

Jan 1, 1980

By T. A. Claasen

Exceptionally low yields in the coking-coal fields of the Soutpansberg area in the northern Transvaal, are taxing the skill and ingenuity of preparation engineers. The coals are highly intergrown, and a series of crushing and washing steps may be required to extract the maximum usable tonnage. In addition, novel preparation techniques may have to be employed. This paper, which is a case study of work recently undertaken, gives a general account of raw coal properties, emphasizing those related to maximum recoveries, and outlines the steps involved in the design of appropriate flow sheets based on laboratory studies.

Jan 1, 1980

The introduction of legal certification of mine managers is a matter of history. It was introduced as part of legislation for mine safety. It has been said that such legislat- ion was written in blood. Like all legislation this legislation is divided into three sections; commands, obligations and sanctions. While legislation in all States on this subject is similar, the differences are great enough to have prompted the preparation of a Uniform Code by the Annual Conference of Chief Inspectors of Mines. This Uniform Code has not been adopted fully by any State to date. Legal certification of mine managers has made managers more aware of the requirements of the legislation covering their industry, legislation that reads as a summary on past accidents and methods of preventing them. While budding managers spend considerable' time in their early years in the preparation for certification, history has shown that the industry has benefited from their efforts. A better knowledge of the safety acts by the managers has produced safer operations, and a higher standard of management has raised the technical standards of mining operations to a stage where Australia can be proud.

Jan 1, 1980

By A. F. Ogg

The installed world steel capacity remains 20% above the present world steel demand. Energy costs have risen enormously in recent years, as illustrated in Figures 1 and 2. The role of the sinter plant is becoming more exacting as it becomes vital to minimize energy consumption. Continuous grate sintering, although pioneered in the United States, has always been the second grade burden preparation route, due to the predominance of easily up- graded ores which were more readily agglomerated by pelletizing. To achieve blast furnace performance up to best world standards, sinter of consistent high quality must be produced with virtually no atmospheric pollution. The plants must be capable of achieving this demanding level of quality whilst utilizing high proportions of revert materials, iron ore concentrates and fluxes . However, with the present difficult economic climate in the iron and steel industry, the economic production of sinter and ultimately steel is becoming increasingly important. The iron and steel industry is looking closely at costs and is identifying the need for sinter plants that will cope with a wide range of sintering materials to give the cheapest blend at varying output levels dependent upon demand. In order to meet these requirements, sinter plant builders are designing plants with particular attention on flexibility.

Jan 1, 1980

By J. E. Pahlman

As part of its goal to minimize the requirements for mineral commodities through conservation and substitution, the Bureau of Mines is conducting research to determine the resistance of alumina refractories to corrosion by alkali-containing slags that could result from burning of the abundant Western lignites in metallurgical operations. Static corrosion tests were performed at 1,000° to 1,350° C and dynamic tests were performed at 1,400° to 1,600° C to investigate the stability of refractory specimens in slag environments. In general, the degree of refractory attack increased with decreasing alumina content in the refractory and with increasing alkali content of the lignite ash. The parabolic kinetics observed in static tests suggested that a reaction product layer is formed through which ionic diffusion must occur to sustain the reaction with the refractory material. The linear kinetics observed in dynamic tests in high-viscosity slags indicated a shearing of the reaction product layer by viscous slags. The observed lesser attack of refractories by low-viscosity slags can be explained on this basis. Two 99-percent-alumina refractories and two 90-percent-alumina refractories formed an expanded protective layer with the more viscous slags but not with the less viscous slags. Corrosion of 90-percent-alumina refractories increased exponentially with temperature. In refractories with the same nominal alumina content, those that contain a combination of a-Al203 and mullite (3A1203?2Si02) have better corrosion resistance than those containing a combination of a-Al203, cristobalite (Si02 mineral), and mullite. In alkali environments (1,300 to 1,400° C), 90-to 99-percent-alumina refractories are recommended for use as furnace linings.

Jan 1, 1980

By H. Dreissen

Upgrading of low-concentration ores is of growing importance today. The Heavy Medium Cyclone Process, thanks to strong centrifugal forces, effectively separates particles varying only slightly in specific gravity but widely in size. The paper discusses the separation efficiency, the method of assessing that efficiency, and the influence of such factors as medium solids. The operating results of nine heavy medium cyclone plants handling following minerals are reported: barite, wolfram, iron, magnesite, diamond, lead-zinc, fluorspar, rocksalt potash. Highlighted are an improved recovery system for heavy medium and some other developments, such as techniques for separation down to 0.1mm and the application in the field of recycling.

Jan 1, 1980

Reduce injuries caused by slips and falls from large haulage vehicles. Approach Replace the flexible-cable or chain-type lower ladder steps, with steps that extend closer to the ground and do not sway when stepped on. Modify dimensions of entire ladder to new industry recommendations. How It Works New lower ladder steps are supported by side pieces made of pretensioned, solid-wound, coil springs fabricated from high strength steel. Unlike conventional crash-resistant steps, which flex or swing freely when stepped on, the spring supported steps can maintain the same inclination as the fixed upper portion of the ladder while supporting an average-weight operator. The steps are also highly resistant to collision damage because they yield on impact if rammed into obstructions such as rocks or berms. See photograph.

Jan 1, 1980

By Smith JW

Studies of 13C/12C ratios of carbon dioxide in seam gases and in secondary calcites show that 1. In mines prone to carbon dioxide outbursting, the source of this gas is external to the coal. 2. Faults draining reservoirs of magmatic or primary carbon dioxide, rather than intrusives, are the most likely points of entry of carbon dioxide into mines. 3. The higher the concentration of carbon dioxide in seam gas and the wetter the mine, the lower the likelihood of secondary calcite occurring as a filling in cleats, fractures etc. 4. A -role played by carbon dioxide in promoting outbursting may be the conversion of calcite to soluble bicarbonate, the removal of this in mine water and the subsequent weakening of the resistance of the bulk coal to stress.

Jan 1, 1980

By Christian Jeger

After recalling the principles underlying fire-damp flow in coal and the essential part played by permeability (Darcy's law) in the intensity of flow, a few theoretical and experimental results showing the possible causes and range of variation of coal seam permeability are presented. The study of firedamp flow into gate roads and of residual gas concentrations in coals as a function of the gate road distance, shows that, in French mines, coal seams in a virgin zone have a very low permeability, but they become permeable when destressed by mine workings, in particular overlying workings. This is the case not only in the fractured zone round a mine excavation in which the gas is released, but also beyond the limit of the zone degassed by the excavation. In the floor of flat seams, upward boreholes can be used for predegassing seams that have been relaxed but not degassed, as the result of an overlying coal face. In this respect we shall describe the predrainage experiment carried out in the Marienau district of the Lorraine coalfield. Predrainage can contribute considerably to the reduction of methane emission in the ventilation of newly opened longwall faces. But to be efficient and useful predrainage should meet certain conditions.

Jan 1, 1980

By Aurel Goodwin

I chose the title "Let's Clear the Air" for this afternoon's presentation because it has two meanings, the literal and the figurative. Most of you know what MSHA is. Most of you know what MSHA does. And, for the most part, most of you know why. What I hope to accomplish today is to "clear the air" around our health standards, to clarify for you how MSHA views its congressional mandate under Title I Section 101(a)(6), (7), and (9) of the Mine Safety and Health Act. Asbestos, silica, radiation, noise, welding fumes, carbon monoxide, lead, hydrogen sulfide, nitrogen dioxide - the list of physical and chemical hazards encountered in the metal and nonmetal mining industry is as diversified as the industry itself, possibly even more so. In addition, miners are often exposed to several of these health hazards simultaneously.

Jan 1, 1980

By L Barro

There is currently a worldwide interest in coal-oil technology as the search continues for alternative energy sources to reduce the consumption of petroleum crude. An important aspect of this coal-oil technology study is to obtain information on the flow properties of coal-oil slurries. While some work has been reported on the flow behaviour of black coal-oil suspensions, very little work on brown coal-oil suspensions has been reported. In this paper flow characteristics of brown coal-oil suspensions for various coal concentration and temperatures have been presented. A capillary rheometer, designed to handle settling suspension, has been used for determining rheological properties. Brown coal of 0.0725 mm average particle diameter has been used in this work. The oil was a coal derived product having a boiling point range of 234¦C - 319¦C. Apparent viscosity of all suspensions was found to increase on storage due to ageing. Ageing might have occurred due to physicochemical interactions between coal and oil. Flow behaviour of some suspensions changed from Newtonian to non-Newtonian on storage. Apparent viscosity increased sharply with increase in solids concentration and suspensions at higher concentration behaved as non Newtonian liquids. Viscosity decreased with increase in temperature; rate of decrease slowed down with increase in temperature.

Jan 1, 1980

By Allan M. Hale

Taconite tailings reclamation, especially the stabilization of tailings ponds, .dams, and slopes, can be effectively accomplished through the use of appropriate vegetation. Utilizing vegetation provides both aesthetic and ecological enhancement of a site while at the same time protecting tailings structures against wind and water erosion. Generally, the methods and techniques for establishing vegetation are well known; however, there are many site-specific factors that can alter a particular reclamation approach. Those factors include slope gradient, tailings material size, solar exposure, and physical and chemical properties of tailings. In addition to the site-specific factors, variations in climate, geography, and physiography of a region can have a pervasive influence on the success or failure of a revegetation program. Both the site-specific and regional factors control reclamation planning in such areas as plant variety selection, methods and times of plants establishment, maintenance techniques, and subsequent monitoring methods. As a result of this multifactor relationship, it is important to establish a data base that identifies both the site-specific and location conditions in order to tailor the reclamation plan to the specific area. When an appropriate data base has been collected, detailing the various site-specific and regional factors that will influence a revegetation program (in the absence of previous testing), it is very beneficial to apply experimental techniques to develop the reclamation plan for a specific site. The reclamation plan for a specific site may include several techniques adapted for the differences found within the specific site as the result of topographic or other influences. Considering this, the Reserve Mining Company and Dames & Moore undertook to develop a successful reclamation plan based on a detailed test plot program conducted at the Mile Post 7 location.

Jan 1, 1980

By Matsushita Y, Maeda M, Sano N

The present study was carried out to explore the possible separate recovery of iron and phosphorus (as gas) from BOF slag using graphite crucibles or graphite powders in the presence of a tin bath. The last is consider- ed to enhance the activity of phosphorus in iron reduced from slag or not to absorb the phosphorus vapour readily. When the slag was reduced in a graphite crucible in contact with a tin bath, the phosphorus reduced from the slag was carried away in CO explosively generated by the reduc- tion of iron oxide. When graphite powder was used as the reductant instead, 78% of the phosphorus was removed from slag, only 3% of which was absorb- ed into the tin bath. The rest left the system as gas. Gaseous dephosphorization depends on the area of contact between slag and reductant as cll n.u the amount of the latter. the reduction behaviour was directly observed, using an X ray transmission technique, to conlirm the reaction mechanism.

Jan 1, 1980

By Benoit Gagnon

Mining of the Schefferville iron deposits began in 1954 on completion of the 574 km railway linking the mines and the St-Lawrence river port of Sept-Iles. Apart from crushing, no treatment of these ores was required before smelting. In the late 1950's, testwork began at Schefferville to develop a process for upgrading the extensive lower grade deposits containing 5l% iron with 15% silica (natural analysis). Engineering for 6.1 million tons per year Beneficiation Plant using cationic silica flotation and the A-C Grate kiln began in 1970 and the first pellets were produced in mid 1973. Production requirements and operating difficulties have restricted capacity to approximately 85% of design but ongoing improvements are being made continuously to attain design capacity.

Jan 1, 1980

Jan 1, 1980

By David E. Pearson

"Western Canadian coking coals are located in the Rocky Mountains arid foothills of British Columbia and Alberta. They are typical of non-marine coals, characterized by total sulphur contents of less than one per cent and with ash contents of 10-30 weight per cent. This mineral matter is composed principally of kaolinite and quartz.The petrographic compositions of most of the coking coals which constitute the 2.065 billion tonnes of British Columbia's measured reserves, and the compositions of the metallurgical coal currently exported from Alberta, show them to be rich in the inertinite macerals, macrinite, fusinite and semifusinite. When the mean maximum reflectance of vitrinite in oil/Romax) is used as the coal rank parameter, this high inertinite content is reflected in the lower volatile-matter yields, but the relatively inert character is also displayed by lower free swelling indices (PSI), lower maximum dilatations, lower maximum fluidities and lower coke strengths than other coals of the same rank, but richer in the reactive macerals, vitrinite, exinite and semifusinite. Despite these reduced values in the so-called caking tests, inertinite-rich coals produce strong coke.A system of classification of coking coals is introduced which is based on rank, as indicated by Ro max, and either petrographic composition, maximum dilatation, maximum fluidity or, to a lesser extent, PSI and volatile-matter yield. Six principal coal groups can be distinguished among coking coals using this versatile classification. Inertinite-rich coals are assigned to the Keystone Group (GI), Balmer Group (G3) or Moura Group (G4), each group being named for a coal typical of that population ofcoals. Reactive-rich coals are assigned to the Pittston Group (G2), Kellerman Group (G5) or Big Ben Group (G6). A multiple-regression analysis of coal quality versus price shows how the value of coking coal in the Japanese market appears to be related to reflectance and the free swelling index, and confirms the economic viability of the classification.British Columbia's measured reserves of coking coal contain representatives of four of these groups; Balmer Group (73%), Moura Group (/6%), Pittston Group (3.4%) and Kellerman Group (7.6%).This analysis of the quality of Western Canadian coking coal indicates that despite the need for large proportions of inertinite-rich coking coal in blends produced in the Japanese steel industry, there is nevertheless a demonstrated overabundance of Balmer Group and Moura Group coals available to the international coking coal market."

Jan 1, 1980