Search Documents

By David P. Lindroth

The Bureau of Mines has developed and successfully tested a hangup clearance module for use in clearing hangups in underground mine chutes and ore passes. The Bureau's tests showed that the hangup clearance module can be effectively used to clear mine hangups. Furthermore, it is believed that clearance using this module is quicker, safer, and more efficient than the method currently used. The hangup clearance module uses a ballistic disk explosive charge that can clear hangups located as far as 50 feet (15.2 m) from the position where the charge is detonated. Mine personnel can therefore set up the module and the charge it contains without being exposed to dangerous areas. This report describes the principles of operation of the module, provides data and drawings for its construction, and gives instructions for its setup and use. The report also summarizes the development of the module, briefly discusses preliminary and underground tests, and lists the current and potential applications of the hangup clearance module to underground mining.

Jan 1, 1982

By David A. Rice

This note describes a simple, rapid technique for measuring the apparent volume and density of individual bits of porous materials such as iron ore pellets or pieces of coke. The method consists of determining the weight recorded on a balance when a particle is depressed below the surface of mercury, and calculating the apparent volume from the known density of mercury. The apparent density is calculated after weighing the particle in air. The method is particularly well suited for applications where a great number of determinations are to be made. An additional benefit is the minimal handling of the mercury. In any event, the usual recommended safety precautions should be adhered to.

Jan 1, 1982

By Jalna R. Zatko

Coal-clay waste slurries were dewatered in laboratory-and small-scale continuous tests by the Bureau of Mines using polyethylene oxide (PEO) as a flocculant. Dewatering from a nominal 7-wt-pct solids to over 50-wt-pct solids was accomplished using 0.5 lb of PEO per ton of feed in small-scale continuous tests. Parameters such as pH, initial solids content, and PEO concentrations were investigated. Water recovered from dewatering was reused as dilutant for PEO solutions.

Jan 1, 1982

By Robert J. Timko, Edward D. Thimons

Sulfur hexafluoride (SF6) is an odorless, colorless, nontoxic gas that has found acceptance as a tracer gas in research on ventilation pat- terns, measurement of air leak rates, respirable dust reductions due to bagging hood modifications, and the study of airflows relating to gob boreholes. Following a short review of the SF6 sampling technique, this report describes recent Bureau of Mines projects in which SF6 was used successfully as a tracer gas, enabling researchers to acquire representative data quickly and inexpensively.

Jan 1, 1982

By D. F. Howarth, F. F. Roxborough

Some important aspects of the design of rock-cutting systems remain relatively unexplored. Two areas of practical significance in this context form the subject of this paper: cutting in jointed or fissured rock, and groove-deepening. A series of controlled laboratory experiments on the performance of disc cutters in jointed rock showed that the spatial and geometrical configuration of jointed rock masses needs to be taken into consideration in the design of mechanized rock excavating systems. One series of experiments showed that, under favourable geometric conditions, the energy required to cut in a jointed rock mass is at least half that required to cut otherwise intact rock. Groove-deepening-the progressive deepening of a groove by successive passes of a cutter-is a potential operational feature with most mechanized rock-excavating systems. Laboratory experiments revealed an important fundamental cycle of events associated with disc cutters when progressively deepening a groove in intact rock. Furthermore, in contrast to pick cutting, groove-deepening by discs is shown to be an efficient operation and one that should not necessarily be avoided. This can be directly attributed to increased interaction between the disc cutters as the result of an increase in magnitude of the lateral forces generated as a groove is deepened.

Jan 1, 1982

By Cyrus W. Field

Metalliferous sediments constitute an important component of the sedimentary veneer that overlies basaltic oceanic crust of the Nazca Plate and elsewhere. Although first collected more than one century ago near the East Pacific Rise during the Challenger Expedition and recognized for their anomalously high content of Fe and Mn, occurring as very fine-grained, yellow-orange, oxides, hydroxides, and oxyhydroxides, it was not until the more detailed studies of Bostrom and Peterson (1966) that their geologic significance and concentrations of other transition metals were fully appreciated. The Nazca Plate is a dynamic lithospheric unit bordered by the Peru-Chile trench and the East Pacific Rise to the east and west, and by the Galapagos Rift and the Chile Rise to the north and south (Fig. 1). Samples employed in this study were taken from piston core recovered from the Nazca Plate (Fig. 2), D. S. D. P. drill core from the northeast Pacific (Dymond and others, 1973), ferromanganese nodules from dredge-haul s at several locations, and from hydrothermal mineral deposits of the Andes. Our efforts have been largely sponsored by the National Science Foundation through its International Decade of Ocean Exploration Pro- gram. The metalliferous fraction of these sediments is widespread, but generally small. Sedimentation is dominated by biogenic silica in the equatorial latitudes, terrigenous debris adjacent to the South American Continent, and by biogenic carbonate elsewhere, except at depths below 3500 m in the central and northwest parts of the Nazca Plate near the East Pacific Rise. Contributions of these distinctive sediment types are shown by the distributions of Si02, A1203, and CaC03 given in Figure 3.

Jan 1, 1982

By James M. Spear

Sample results suggest the only mineral resources in the study areas are placer gold deposits along the South Fork Kern River in the Woodpecker RARE II unit (fig. 1). These deposits, in Rockhouse Basin, total 4.5 Figure 1.--NEAR HERE. million cu yds (3.4 million cu m) of indicated subeconomic gold resources in four deposits of "older" gravel. Gold value in samples averages $0.36 per cu yd ($0.47 par cu m) and is as much as $4.44 per cu yd 1/. Cost of mining the gravel and recovering the placer gold is estimated to be more than $2 per cu yd ($2.62 per cu m) for a deposit of this size and type. Additional inferred subeconomic placer gold resources with similar grade probably occur in four other deposits of "older" gravel on which no mining claims were located. Placer gold occurrences on upper Trout Creek contain gold worth as much as $4.50 per cu yd ($5.88 per cu m) 1/. Average grade is much lower, and only about 1,000 cu yds remain (760 cu m). These occurrences do not constitute a resource, but may attract hobbyists not dependent upon making a profit.

Jan 1, 1982

By Edward C. Heistermann

The Falkirk Mining Company, a wholly owned subsidiary of The North American Coal Corporation, is located 80 kilometers (50 miles) north of Bismarck, North Dakota. Falkirk is under contract to provide 5.08 mil- lion tonnes (5.6 million short tons) annually to the Coal Creek Generating Station, an 1100 mega- watt electric plant owned by the Cooperative and United Power Associations of Minnesota. Coal Creek is located 2.4 kilometers (1 ½ miles) south of the Mine. Electricity from the plant is transmitted to rural electric customers in Minnesota via a 400-kilovolt D.C. power line.

Jan 1, 1982

By John P. Coughlin

Software techniques developed by the Bureau of Mines Denver Research Center for real-time microseismic data analysis are presented. These techniques focus on the simple acquisition of P-wave arrival times and their use in event location. The paper discusses in detail software techniques to separate microseismic events from mining noise such as drilling and from very large events such as rock bursts. Incorporation of these techniques has enhanced the reliability and accuracy of computer-based monitoring of microseismic activity in ongoing research by the Bureau.

Jan 1, 1982

Provide a central source of subsidence reference in formation for industry, academia, and government agencies interested in improving subsidence prediction and analysis under U.S. mining conditions. Approach Develop a comprehensive bibliography about mining related surface subsidence and store this information in a computer file. Make specific references accessible through a key word retrieval program. Supplement these key word identifiers by entry of author's name, title of publication, subject of text, or sponsor of publication. How It Works Requests for subsidence in-formation are made by phone or mail to the Bureau of

Jan 1, 1982

By Firth B. A

The flotation of fine coal (minus 0.5 mm) often requires the addition of an insoluble hydrocarbon collector to apparently promote the adhesion of coal particles to air bubbles. A series of experiments was conducted using a radiotracer and narrow size fractions of clean coal to determine the effect of particle size distribution, collector addition rate, desliming of feed and emuIisification of collector on the distribution of collector between the different size fractions. The concentration of collector per gram of each size fraction was found to be approximately proportional to (average particle size)-2 except if the collector was emulsified prior to addition, the dependence altered to approximately (average particle size)-1. Mechanistic consequences are discussed.

Jan 1, 1982

By Kazuteru Tozawa, Robert G. Robins

"The stability of calcium arsenate is discussed in relation to the possible misuse of lime in the treatment of gold processing waste waters. Stability diagrams have been derived and experimental results cited to show that calcium arsenate has a higher solubility in neutral to alkaline solution than has previously been recognized and this solubility is further enhanced by the presence of carbon dioxide, bicarbonate or carbonate.IntroductionThe removal of arsenic from gold mine waste waters has been of interest for more than thirty years, but with the recent emphasis on clean water standards there has been renewed activity in relation to that problem. The processing of gold-bearing sulphides which contain arsenopyrite and other complex arsenic sulphides is well established. Initial roasting to oxidize the sulphides leaves the arsenic in the form of both arsenic and arsenic, in which forms it is soluble in the subsequent leaching stage. Further oxidation of the leach liquors is required before the well-established procedure of precipitating calcium arsenate with lime, which is carried out despite an immense lack of knowledge of the calcium-arsenic-water system.The solubility product and free energy of formation for Ca3(AsO4)2, which are to be found in recent and reliable sources of data, originate from the work of Chukhlansev, whose experimental determination of the concentration of calcium from the solubility of calcium arsenate in solutions of various pH yields the results plotted in Figure 1. This is the work which has resulted in a wide acceptance of the ""insolubility"" of calcium arsenate and the use of lime to stabilize arsenic in that form.Laguitton attempted to further elucidate the chemistry of the lime addition method for treating arsenical waste waters from gold processing operations. The low solubility product for Ca3(AsO4)2 was the basis for his examination of likely chemical equilibria in the system. Laguitton and other workers have not considered atmospheric carbon dioxide as an important component in this system."

Jan 1, 1982

By M. A. Mahtab, T. M. Yegulalp

This paper presents the development and application of an approach for clustering fracture orientation data. Data are projected on the surface of the unit upper hemisphere and the clustering approach is applied in three steps: (1) randomness test and identification of dense clusters, (2) estimation of cluster statistics, using Bingham distribution, and (3) rejection of extremal data based on Chauvenet's criterion.

Jan 1, 1982

By Thomas G. Carnahan

The Bureau of Mines conducted research to simulate in situ leaching of a chalcopyrite ore. The purpose was to obtain a direct comparison between moderate-temperature and elevated-temperature in situ leaching of copper trom minus la-inch ore and to analyze the sulfuric acid and oxygen requirements of the leaching system. Experiments employing oxygen were conducted at 35° and 90° C on 362-and 367-1b ore charges, respectively, under flooded conditions and at 400 psig. At 90° C, 47 pct of the copper was extracted in 913 days of leaching; at 35° C, 27 pct of the copper was extracted in 915 days. Diffusion into and out of the ore fragments con-trolled the rate of leaching. Oxygen consumption was 1.46 lb/lb of copper extracted at 35° C and 3.15 lb/lb of copper extracted at 90° C. Sulfuric acid requirements of the ore were 5.49 and 7.48 lb/lb of copper extracted at 35° and 90° C, respectively.

Jan 1, 1982

The determinants of human behaviour are numerous and complex. Many scientific disci- plines focus on various processes which play some part in shaping the actions of individ- uals and groups. Behavioural science attempts to synthesise data produced by these investigations in an attempt to formulate principles by which people's thoughts, feelings and actions may be described, diagnosed, predicted and changed. While no comprehensive account of people and their reactions can be attempted in a brief paper a review of six principles does provide a framework within which managers can establish reliable knowledge applicable to all their subordinates and to themselves. This information may be used to arrange organizational environments and management practices which enable people to discover, release and increase their best intellectual, emotional and motivational capacities.

Jan 1, 1982

By D. E. Kirby

In line with the Bureau of Mines' goal of providing technology to maintain a supply of minerals adequate to meet national economic and strategic needs, a method for recovering chromite from lateritic materials was investigated. Laterites are a large resource of Ni, Co, and Cr, critical metals of which the United States has insufficient domestic sources. A roast-leach method was developed by the Bureau to extract nickel and cobalt from domestic laterites. A concurrent effort was made to recover chromium from either unprocessed laterites or the leach residues. This report characterizes laterites and laterite leach residues. It describes a chromite recovery procedure using conventional industrial beneficiation equipment for sizing, low-intensity magnetic separation, and gravity concentration. Concentrates containing 20.0 to 22.4 pct Cr (29.0 to 32.7 pct Cr203) and with a 1.6:1 to 1.9:1 Cr-Fe ratio were recovered from laterites and residues containing 1.3 to 2.5 pct Cr with recoveries exceeding 50 pct. Because of their low grade and fine size, these concentrates would be suitable for preparing chromium chemicals. The direct beneficiation of laterites for chromite recovery resulted in the minerals containing nickel and cobalt concentrating in slime products. No iron oxide coproducts of acceptable grade were recovered from either laterites or residues.

Jan 1, 1982

By Arthur R. MacPherson

Este capítulo revisa las etapas que deben seguirse desde el momento de considerar la molienda autógena en el desarrollo de un nuevo depósito de mineral o en la expansión de una planta existente, hasta la compra de un molino autógeno. En este caso el término autógeno incluye: semi-autógeno, molinos de pebbles secundarios y molino de bolos (trozos), así como los sistemas de molienda autógena total. También se han incluido las alternativas por vía húmeda y seca. Antes de programar el ensayo debe decidirse cuantas muestras brutas son requeridas para calcular propiamente las posibilidades de molienda autógena del depósito. También ha de tomarse la decisión, de como y donde deben tomarse las muestras, por ejemplo: planta piloto situada en el sitio de localización de la planta o en otro lugar establecido; molienda en húmedo y/o en seco....etc. En el mismo programa del ensayo se obtendrán ciertos datos fundamentales. Los ensayos deberán incluir un trabajo suficiente. para determinar cuál de las moliendas, totalmente autógena o semi-autógena, debe utilizarse; y qué tipo produce la máxima eficacia en la potencia consumida. También, los otros datos pertinentes deben ser recolectados, como por ejemplo: potencias, tonelajes, alimentación, carga, tamaño del producto, carga circulante, etc. Si es necesaria una molienda secundaria para obtener el tamano final, la decisión de qué molienda debe emplearse (molino de pebbles o molino de bolas) puede requerirse un ensayo de trabajo adicional. Finalmente, la concentración del mineral puede jugar un papel importante en la selección del circuito y debería ser una parte del ensayo final una vez que se ha establecido la molienda. Para determinar qué tipo de molinos pueden satisfacer los requerimientos establecidos por la planta piloto, debe tomarse una escala para ciertos datos como: potencia del molino, consumo de acero, simple o doble etapa de molienda, tipo de molino secundario. Para asegurar un posterior entendimiento del depósito de mineral y sus características de molienda, deberán efectuarse algunos trabajos adicionales a pequena escala utilizando pequeñas muestras y molinos para producir unos datos comparables de molienda. También, algunos ensayos tales como medio de molienda óptimo, e índice de trabajo, deberán ser completados.

Jan 1, 1982

By Howard M. Wells

Investment in minerals development usually entails big financial outlays. which will remain at risk for a long time before the venture can begin to generate a return cash flow. Before 'committing himself to such a venture the investor would be wise to carefully examine the possible consequences of his exposure to risk. In this context risk is defined in multiple terms, which relate the magnitude of possible loss with the probability that such loss may occur--normally the probability will decrease as the amount of possible loss increases. The analysis of risk is an essential component of the decision making process, especially so in the case of low grade high tonnage mining ventures where a very real possibility exists that future unfavorable circumstances may lead to losses that could cripple or ruin even the richest corporation. Wells (1979) postulates a rationale for making the investment decision under uncertainty based on the comparison of two independent risk criteria: 1) the risk inherent in the venture represented by the negative portion of the cumulative distribution of the net present value (NPV), as derived by a stochastic evaluation procedure, 2) the limits of risk the decision maker is willing to accept, taking account of the financial capacity-of the 'firm to absorb various levels of future cash shortfall should the venture prove disappointing. The chance the investor would be prepared to accept can be expected to decrease as the amount of the possible shortfall increases. The limits of acceptable risk are-defined by a curve called the "LL-curve" which can be directly compared with the cumu¬lative NPV curve. A positive investment decision is implied if the limits of acceptable risk are not exceeded.

Jan 1, 1982

By H. H. Dewing

The Bureau of Mines constructed a process research unit (PRU) to demonstrate new technology for extracting zinc from sphalerite concentrates. Up to 9 kg/hr of sphalerite (ZnS) concentrate was reacted at ambient pressure in the PRU with 80 pct sulfuric acid at 160° to 180° C to produce zinc sulfate and elemental sulfur. The PRU consisted of a three-stage glass reactor system: a 4-liter premix stage in which feed was slurried with 78 to 82 pct H2S04, a 40-liter stirred reactor, and a ISO-liter settling stage in which high reaction conversions were effected and excess H2S04 for recycle was separated from insoluble ZnS04 and sulfur. Evolution of sulfur-containing gases was minimized by sub-surface addition of acid feed slurry to the stirred reactor and by exclusion of air from the reactor to prevent the oxidation of elemental sulfur. Conversion of zinc to zinc sulfate averaged over 99 pct at the optimum acid concentration of 80 pct. Total sulfur losses (primarily S02) were less than 2 pct of the sulfur in the sphalerite. Elemental sulfur remained in the insoluble portion of the settled reactor product after leaching with simulated spent zinc electrolyte containing sulfuric acid. The sulfur residue contained 75 to 89 pct sulfur. Neutral zinc sulfate, required for zinc electrowinning processes, was separated from the sulfuric acid leach solution by crystallization at -15° C as zinc sulfate heptahydrate (ZnS04?7H20). The crystallization operation simultaneously effected a partial concentration of the recycled electrolyte solution by removing water.

Jan 1, 1982

By G. Capello

Carboniferous mining basins are today a non-negligible source of energy. So important in fact that returns now justify high investments and costs even for those deposits that were un-economical in the past. Nowadays, if properly explored and exploited, basins previously considered non-minable due to complex structural and stratigraphical situations may be economically interesting. It is while studying a faulted basin with such features that the Authors developed the described computer-aided methodology capable of constructing a model of the physical structure of coal deposits on the basis of stratigraphical data from drillings. The aim of the procedure is to define coal reserves, the exploitation of a deposit being conditioned by the possibility of identifying zones that are technically minable. This objective is pursued by making as detailed a reconstruction as possible of the geometrical, stratigraphical and tectonic features of the coal-bearing seams of a deposit.

Jan 1, 1982