Search Documents

By E. A. Johnson

The Bureau of Mines determined the effect of slag additives on copper solubility and the distribution of typical impurity elements between copper-iron matte and silica-saturated fayalite (iron silicate) slag at 1,250° C, in CO-C02 atmospheres with 10 pct S02. Small additions (<10 pct) of CaO, A1203, and MgO were shown to decrease copper solubility in the slag. Additions of CaO increased the solubility of bismuth and tellurium in the slag at lower matte grades. Al 20 3 additions decreased the solubility of tellurium in the slag, but increased that of bismuth at lower matte grades. A1203 additions increased the solubility of both at lower matte grades. With no additives, matte grade did not affect the solubility of bismuth in slags, whereas increasing matte grade resulted in a slight decrease in the tellurium solubility in slag. Additions of CaO or As203 alone to the slag increased selenium and arsenic distribution to the matte, but had little or no effect on antimony distribution; whereas small MgO additions decreased antimony distribution to the matte but had no effect on arsenic and selenium distribution. In slags with no additives, selenium distribution to the matte increased with increasing matte grade, while that of antimony decreased and that of arsenic was unchanged.

Jan 1, 1982

By Jorgensen FRA, Moyle FJ, Turner TM

Laminar flow furnace techniques and thermal analysis were used to study the combustion of Kambalda nickel concentrate and Collie coal. The study was made to ascertain the suitability of the latter as a replacement for the fuel oil currently burnt in a flash furnace at the Kal- goorlie Nickel Smelter. The coal was found to ignite at temperatures between 500-600¦C which was the same as that required for the most reac- tive component of the concentrate, namely py- rite. The rates of reaction of both the coal and concentrate were dependent on oxygen con- centration. Sulfur dioxide hindered the combus- tion of concentrate and of coal, the effect on the concentrate being the more pronounced. The effects of moisture content and the tendency for spontaneous combustion of the coal were also noted.

Jan 1, 1982

By A. S. Block-Bolten

Two innovations in nickel-arsenic separation have been studied on a laboratory scale. The first requires only a nitric acid atmospheric leach without preliminary roasting and leads to favorable final conditions for precipitation of arsenic as highly stable FeAsO4, The second is an NaOH-H2O2 pressure leach which is an alternative to the known NaOH-O2 pressure leach. Either method offers the possibility of rapid and efficient separation of nickel from arsenic and is applicable, for example to the high grade niccolite deposits in the Great Slave Lake area of northern Canada.

Jan 1, 1982

By G. Kollberg

"IntroductionThe SALA Caravan Mill system represents a proven concept for the design and operation of mobile and semi-mobile ore dressing plants.The Caravan Mill has been developed to meet the demand for a flexible processing plant to be used for small and medium-sized orebodies or for pilot investigations of deposits directly at the mine site e •The first Caravan Mill installation was put into operation in 1970 and a number of plants have been delivered world-wide since then.The Caravan Mill system has great flexibility both in capacity, ranging from 50 to 1000 tons per day, and in process combinations. The process modules available are:• crushing by jaw and cone crushers;• pre-concentration by the Dyna Whirl Pool dense media system;• grinding by wet rod or ball mills;• separation by gravity, magnetic, flotation or leaching-CVP adsorption methods;• dewatering by lamella or conventional thickeners and vacuum filters.To form complete plants, auxiliary equipment is also available, such as:• bins, feeders and conveying systems;• power generator units;• water tank and pump for process water;• interconnecting piping and cables;• erection and service tool kits;• set of spare and wear parts.For mine sites with rainy or winter conditions, a plastic tent with air heater can be supplied to cover the ore dressing equipment. Each module is workshop assembled complete with slurry pumps, internal pipe work, electric wiring with plug-in connections, hoses, etc., all arranged for quick and simple connection between the units. Before delivery, each unit is tested in the workshop."

Jan 1, 1982

By Larry Joe Linley

The Department of the Interior, Bureau of Mines is reviewing explosion protection methods for use in gassy coal mines. This performance criteria guideline is an evaluation of three explosion protection methods of machines electrically powered with voltages up to 15 000 volts AC. A sufficient amount of basic research has been accomplished to verify that the explosion-proof and pressurized enclosure methods can provide adequate explosion protection with the present state of the art up to 15 000 volts AC. The routine application of the potted enclosure as a stand alone protection method requires further investigation or development in order to clarify performance criteria and verification-certification requirements. An extensive literature search, a series of high voltage tests, and a design evaluation of the three explosion protection methods performed at White Sands Test Facility indicates that the explosion-proof, pressurized, and potted enclosures can all be used to enclose up to 15 000 volts AC, if the performance criteria and verification-certification requirements recommended in this guideline are implemented.

Jan 1, 1982

By C. W. Morris

This Final Report describes the major technical activities that were accomplished to produce a comprehensive continuous miner training system (CMTS) for coal industry utilization. The primary product of this program was a continuous miner part-task trainer. It is composed of an interactive computer graphics system combined with the operating controls of a continuous mining machine mounted in a simulated cab. The cab contains an audio system for reproducing continuous miner operational sounds. The trainer is supplemented with a complete set of cognitive materials that provide instruction in the operation, safety and health of continuous miner operations. A complete summary of the field test and evaluation of the CMTS is provided along with a set of recommendations for further training program refinements, expansions, and utilization.

Jan 1, 1982

The application of methods using large diameter down holes has become an important facet in both the development and stoping operations of mines within the Aberfoyle group. Holes of up to 98 metres (vertical) and 78 metres (inclined) have been successfully used in stoping operations. A number of rises have been developed to meet ventilation, servicing and escape-way requirements. The most ambitious rise to date has been a..vertical 93 metre long by 4.50 metre square ventilation rise. Although some early problems were experienced, the ultimate successful completion of this rise has enabled the technique to be incorporated with confidence in future mining plans. This paper summarises experience in long hole rising techniques, their evolution from the original cratering concepts, and the approach to further development of these techniques.

Jan 1, 1982

By Terry G. Richard, Sunder H. Advani

A sequence of 250 unconfined compression tests were completed on a common marine shale indicative of the overburden strata of east- central Ohio. The samples were of a light gray clay shale of Pennsylvanian age. The shales considered are obvious layered materials with distinct bedding planes. For this reason there is sufficient evidence to consider this material as anisotropic in nature. With a properly chosen reference coordinate system this anisotropy can be reduced to a layered orthotropic characterization. This implies that the mechanical properties can be specified with regard to principal material directions. With this nature in mind a systematic study of the combined influences of strain rate and moisture conditioning was initiated. Of particular interest is the variations in unconfined ultimate compressive strength with variations in the controlled parameters of strain rate, moisture conditioning level and direction of testing. Results of this particular phase of the program are presented.

Jan 1, 1982

By C. W. Fitzgerald

INTRODUCTION Continuous mining machines are used in regular flat ore beds having uniform thickness. Since coal is the most common type of material occurring in such beds, most continuous miners are used for the extraction of coal from underground mines. The first continuous mining machine for under¬ground coal mining was introduced in 1948. In one machine, the continuous miner combines the functions performed by a conventional face drill, a cutting ma¬chine, and a loading machine. It breaks or digs the material out of the surrounding solid and transfers the material back through the machine chassis by means of a chain conveyor. The conveyor carries the material to a haulage system, usually a rubber-tired vehicle known as a shuttle car. Generally, continuous miners are used in seam heights from 890 to 3660 mm (35 to 144 in.). For seam heights of 1070 mm (42 in.) or less, the haulage system may be a multiple-bridge conveyor or battery-powered tractors that haul low-bed trailers. Proj¬ects are being undertaken by private industry and through government contracts to develop a continuous haulage system for all seam heights. As of 1976, the majority of continuous miners were of two types. The first type is the drum miner, which mounts the cutting elements on a series of drums across the cutting head of the machine, sometimes using a cutting chain to cut clearance for the gear drive. In the drum-type machines, the cutting head rotates parallel to the material face. The second type is the auger miner, which utilizes cutting elements mounted on two auger-type cutting heads. One head is located on each side of the machine, with the heads mounted per¬pendicular to the material face. Chain-head ripper-type miners/miners having rotary cutting elements with oscillating motion and twin-head boring-type miners have all been popular within the last 15 years. Although these are considered obsolete, some machines are still being supplied for specialized applications. GENERAL DESCRIPTION This chapter describes only continuous mining ma¬chines available as manufacturers&apos; production models as of September 1976. Figs. 1 through 11 illustrate some typical machines currently in use. Cutting Elements The cutting elements are the interface between the machine and the material being mined. In describing the cutting elements, consideration must be given to the differences between the drum- and auger-type machines, the bit-tip speeds, and the bit types. Drum-Type Continuous Mining Machines: Three of the four principal manufacturers of drum-type miners use multi-motor designs that provide separate a-c motors for driving the cutting elements. Gear trains are used to reduce the speeds of the motors to the rotational speeds of the cutting elements. One of the three suppliers drives the cutting elements of its low-seam models with a heavy-duty drive chain that is equipped with cutting bits; all other functions of this machine have separate motor drives that are either electrical or hydraulic. The fourth principal manufacturer generally provides two a-c electric motors, utilizing gear reducers, drive shafts, and hydraulically operated engaging clutches to power all of the operating functions, including the cut¬ting elements. Some drum-type miners use trim chains, equipped with cutting bits, to cut clearance for the gear drives. These trim chains vary from two 305-mm (12-in.) chains to one 760-mm (30-in.) chain per machine, de¬pending upon the manufacturer&apos;s design concept. In all machines other than the low-seam models that use chains to drive the heads, the trim chains are driven by sprockets on the drive shaft of the final cutterhead drum; therefore, the trim chains are not used for power trans¬mission to the cutting elements. In addition to cutting clearance for the gear drives, the trim chains provide uniform bit spacing all the way across the head and assist in moving the cut material to an area where it is either loaded directly into the miner&apos;s conveyor or is easier to load into the conveyor. On a drum-type mining machine, the cutting ele¬ments all rotate from the top to the bottom. Therefore, the recommended procedure is to raise the cutterhead to the maximum seam height, sump the entire machine forward to maximum depth by means of a crawler drive, and then shear downward until the cutter elements reach the floor level. The maximum sump depth varies ac¬cording to the drum diameter, the type of material, the floor conditions, and the operator&apos;s abilities. It normally varies an average of 460 to 760 mm (18 to 30 in.). Cutter drums are supplied with two types of cutting bit holders. Weld-on holders are attached permanently. Pin-on holders are replaceable at the face. Cutter-drum diameters over the bit tips vary from 660 to 965 mm (26 to 38 in.), depending upon the chassis height of the machine and the range of cutting heights. Auger-Type Continuous Mining Machines: As cut-

Jan 1, 1982

By Slater R

The initial planning and detail design phase leading to the development of a 7.5 m internal shaft to service the deep 3000 and 3500 copper orebodies at Mount Isa, Queensland is well advanced. The choice of internal shaft access was made over alternative methods such as a decline from existing levels and borehole hoisting. The resulting access development requirements and shaft configuration for production have been determined. Several techniques are being studied for shaft development. These include the application of blind shaft drilling and large hole reaming methods as well as conventional sinking techniques. As the 3000/3500 Orebodies extend from 1000 metres to more than 1800 metres below the surface, high stress conditions and ground temperatures ranging from 45CC to 62CC are anticipated. The effect of these on the methods being investigated to create a favourable working environment will influence the final choice. Exploration diamond drilling is in progress to confirm the geology of the orebodies so that planning for their extraction including refrigerated ventilation concepts can proceed.

Jan 1, 1982

Continuous remote sensing of methane concentration in underground mines. Approach A methane transducer, developed as a fixed point rib-or face-mounted operating device, measures ambient levels of methane and produces a signal that is proportional to the measured concentration. How It Works The methane transducer, developed under contract for the Bureau of Mines, uses a catalytic-type sensor which will detect methane concentration. The transducer is mounted vertically, as shown. This type of mounting minimizes dust accumulation on the sensing element, which might cause degraded operation. The unit must not be located in an area where water can continuously drip or run on It. The transducer generates an electrical signal proportional to methane concentration at the sensor. A sensor failure output indicates the status of the sensing element A circuit within the methane transducer detects whether the sensing element is shorted or open. A high signal (approximately 8 Vdc) on the failure output Indicates the sensor element is operating In Its normal range. A low output (less than 1 Vdc) indicates an element fault. The methane transducer, enclosed in a stainless steel

Jan 1, 1982

By D. K. Grubbs, A. B. Moose

A brief overview of domestic sources of anorthosite in Oklahoma and Wyoming is presented, including drilling data on anorthosite and limestone exploration.

Jan 1, 1982

By G. Robert Frey

INTRODUCTION This chapter on underground rotary drills briefly describes the equipment features, selection or applica¬tion criteria, safety features, and relative costs of both face and roof drills. After a brief description of the basic components, the application, safety, and cost con¬siderations will be explored. ROTARY DRILL COMPONENTS As illustrated in Fig. 1, an underground rotary drill consists of five basic components. These components are the energy system, chassis, boom, feed assembly, and operator&apos;s station. Energy System The energy system of a typical underground drill con¬sists of an electric motor, driving a hydraulic pump or pumps. Usually, the drill is equipped with a cable reel to store the trailing power cable from the portable power center in the mine. A simple control box is supplied to house electrical switchgear and protective devices. In addition to the pump, the hydraulic portion of the energy system includes the hydraulic cylinders, hydraulic tram motors, relief valves, control valves, etc., necessary to actuate the various machine functions. Chassis The chassis provides the frame or support structure for the other four basic components of the drill. Fre¬quently, it incorporates an oil reservoir for the hydraulic system. The chasis provides the support for the trans¬mission, which drives rubber tires or, in the case of some foreign machines, the crawler tracks. The steering link¬age and steering tires also may be considered as parts of the chassis. Boom The boom is the structure that supports the feed assembly; it is either hinged or pivoted on the front of the chassis. Hydraulic cylinders on the boom are used to lift or swing the boom relative to the chassis and to swivel or "roll" the feed assembly. Feed Assembly The feed assembly is made up of the support struc¬ture with an integral thrust mechanism, a rotation unit, centralizers to stabilize the auger, and a hose handling arrangement. In addition, most drills have an extension frame with a tilt device to aid in positioning the feed. Operator&apos;s Station The operator&apos;s station is the area from which the miner operates the drill. UNDERGROUND ROTARY DRILL APPLICATIONS Underground Face Drills Underground face drills are used in mining opera¬tions that utilize the conventional mining system. The face drill is used to drill holes in the exposed face of the material, and the face is then "shot" by means of explo¬sives or high pressure air. The loose material then is ready for loading and transporting from the face to the preparation plant. Typical specifications for under¬ground face drills are listed in Table 1. Certain parameters should be established as to where the drill is to be used and what is expected of it. To create an awareness of some of the considerations that too often are overlooked, some questions are listed that should be asked in conjunction with the selection or application of the proposed drills. Energy System: Can the drill be supplied with the proper voltage to match the available or proposed elec¬trical power system of the mine? Is the system 250, 460, 500, 550, or 950 v; dc or ac; 3-phase; 60 or 50 Hz? Is the drill equipped with an adequate electric motor to handle the proposed duty cycle? Typical motor power on a single-boom drill would range from 25 to 40 kW (35 to 50 hp); the nominal power for a dual-boom

Jan 1, 1982

By Nick Warren

The problem considered is that of predicting rock physical properties from observations of the structure of the rock. The approach here departs from previous studies in that both the physical properties and structural features are taken as statistical data and the relations between them are cast as statistical functions. This approach I have termed a "quantitative petrostructure analysis". This Paper deals with two aspects of making such a study; parameterizing patterns of topographic features of rock, and characterizing variables to allow correlation studies to be carried out. The principle of a quantitative petrostructure analysis is outlined and illustrated using maps from two samples of Conway granite.

Jan 1, 1982

By Robert C. Speck

The U.S. coal industry has long utilized the pillar-extraction mining technique as a method for maximizing coal recovery. Like longwall mining, it causes large-scale movements that progressively propagate from mine-level to the ground surface and may affect the groundwater regime, surface drainage and surface structures. The U.S. Department of Energy, in an effort to foster in- creased use of total extraction mining techniques, has recognized the need for a better understanding of these movements that will lead to a greater compatibility between coal mining and present and future land use. As part of that goal, GAI Consultants, Inc. is currently in- stalling instrumentation to monitor the ground movements associated with pillar extraction mining at Kitt Energy Corporation&apos;s No. 1 mine in northern West Virginia.

Jan 1, 1982

US 4,194,902 - Pig iron or other molten lion is effectlvely desulfurized by treatment with a mixture preferably about 60% by weight commercial grade calcium carbide, 30% dried limestone diamide, and the remainder bituminous coal. Equivalent desulfurization is obtained using a significantly lesser amount of desulfurizer than in previous mixture of calcium carbide and limestone diamide W Gmohling, assigned to SKW Trostberg AG. Mar 25, 1980. 3 pp. (75-55) Filed: 9-12-78 (941,659) Priority. West Germany, 9-15-77 (2,741,588). Same. British 2,008,153, dated May 31, 1979.

Jan 1, 1982

By J. A. Stewart

"A common problem in the mining industry involves the overloading of established conveyor systems. This overloading can have a number of causes, such as new production technology or a changing market condition which increases demand. An overloaded system usually spells disaster and leads to clean-up problems, equipment failures and lost production. The Cape Breton Development Corporation&apos;s Lingan Mine had a serious overloading situation on its underground coal clearance system, and equipment was being damaged and production was being lost. It was rectified, in part, by increasing the coal clearance capacity through the use of booster conveyors. This paper discusses the problems which led to this situation, the booster concept and the installation of the first unit at the Lingan Mine.IntroductionThe Lingan Mine is a submarine coal mining operation with an annual production of 1.5 million tonnes from three advancing longwalls. Coal is conveyed 3400m up a 13% slope to the surface. Designed and installed in the early 1970s, the system&apos;s 820-tonne/hour design initially proved adequate; however, by the late 1970sthe system was handling surge loads of 1640 tonnes per hour due to the introduction of new face equipment.The coal clearance system consisted of three 485-Kw, two 210-Kw and one 105-Kw conveyors. Each conveyor was designed for 820 tonnes per hour using 1050-mm, Type 10 belt with a 35-degree troughing profile.There were many effects of the overloading on the system:• Loading beyond the physical capacity of the belt resulted in spillage along the conveyor, which increased operational and maintenance costs.• Overloading of the drive components resulted in premature equipment failures.• Spillage at the drive pulley often resulted in damage to the belt and pulley lagging and, under extreme conditions, the conveyor would require partial unloading before it would operate. This was a particular problem under wet conditions because the 485-Kw conveyor drives were fitted with single-drive drums."

Jan 1, 1982

By E. Knell

COM Energy, Inc., a subsidiary of Occidental Petroleum Corporation, has constructed a 1.6 million hectoliter-per-year COM plant in Jacksonville, Florida. COM will be distributed to customers in the region as a substitute for fuel oil presently burned in boilers and kilns. As the market for COM grows, COM Energy, Inc. expects to build additional units both in this country and overseas. This paper addresses the overall status and technical aspects of the project, focusing on the facilities for COM production and utilization.

Jan 1, 1982

By John F. M. Sims

Political issues and a glaring infrastructure deficiency have retarded the emergence of a strong mining component to the Alaskan economy in recent years. Barriers to orderly mineral development are slowly being removed attendant upon changing political circumstances. Infrastructure development, as an investment avenue as well as a responsibility of the State, is receiving much greater attention than in the past. Alaska of course has a rich and varied mining history going back to the 19th Century. This paper, however, focuses on the mining potential, not the mining heritage of the 49th State. The mining industry is emerging from a nadir in the economic cycle - times during which it was buffeted by unsympathetic administrations and confused and confounded by the protracted land status- conflicts prior to enactment; of the Alaska National Interest Lands Conservation Act (ANILCA) and other milestone legislation. Today Alaska&apos;s mining industry looks toward a bright and healthy future and, in the process, will become a very important and vital component of the State and national economy.

Jan 1, 1982

By Tore M. Larsen

The Rødsand Gruber mining company is a subsidiary of the Norwegian industrial corporation Elkem AS, and its mine is situated in the northwestern part of southern Norway. The ore from this mine is a relatively low grade, magnetite ore with a small amount of vanadium. The ore bodies are very irregular in shape, resulting in a high amount of waste rock intrusion in the stopes. The annual underground production in the mines is approximately 1 million t. Because of varying dimensions of the ore bodies, both transverse and longitudinal stopes are employed. The inclination of an ore body is usually 1.04 to 1.59 rad (60 to 90°), and the horizontal width varies up to 100 m. Sublevel stoping has been the traditional mining methods in this mine. Until a few years ago, the ore was primarily blasted using horizontal blasthole fans drilled from Alimak raises. Recently, however there has been an increasing demand for a les expensive mining method. Alternate systems were considered, and finally a method based upon large blasthole stoping was found to be the most suitable. GENERAL LAYOUT The general layout of a stope is shown in Fig. 1 As with all the figures in this chapter, only the prin¬ciples of the method are emphasized and the details may not be valid for any particular site in the mine. In transverse stopes, the horizontal width of the ore determines the length of the stopes. The average length is approximately 50 m, the width of the stopes is 20 m, and there is a 10-m wide vertical pillar between. The distance between the main levels is 60 m. Usually a horizontal (sill) pillar 10 m thick is left below the mucking level. Each stope is first undercut along the entire stope length. This undercut is made with 50.8-mm (2-in.) diam drill holes in a fan pattern. At the moment this is being done by a trackless Atlas Copco Promec jumbo equipped with two Cop 130 pneumatic rock drills. The drill drift is 4 X 4 m, and the crater is 20 m high. This leaves a 36-m stope height to mine with large blastholes. To achieve a fair portion of vertical drilling withlarge blastholes, there are two parallel drill drifts at the top of each stope. These drifts are 4 m high and 9 m wide, separated by a 4-m wide pillar in the middle of the stope. To ease the drilling of perimeter holes, the drifts extend 1 m into the vertical pillar on each side of the stope. The pillar will thus be only 8 m wide on the drill drift level, but 10 m wide down the rest of the stope.

Jan 1, 1982