Search Documents

By Richard A. Arterburn

For many years hydrocyclones, commonly referred to as cyclones, have been extensively utilized in the classification of particles in comminution circuits. The practical range of classification for cyclones is 40 microns to 400 microns, with some remote applications as fine as 5 microns or as coarse as 1000 microns. Cyclones are used in both primary and secondary grinding circuits as well as regrind circuits. The information given in this chapter is intended to provide a method, at least for estimating purposes, of selecting the proper number and size of cyclones and to determine the proper level of operating variables. Generally, it is recommended that cyclone suppliers be consulted for sizing confirmation. Sow cyclone suppliers employ digital computers to aid in the sizing and selection of cyclones. CYCLONE DESCRIPTION AND BASIC OPERATION Figure 1 shows a cutaway view of a typical cyclone. During operation, the feed slurry enters the cyclone under pressure through the feed pipe into the top of the cylindrical feed chamber. This tangential entrance is accomplished by two types of design, as shown in Figure 2. Since the majority of research has been done with the involuted type, the graphs and relationships shown may not be strictly applicable to other designs. As the feed enters the chamber, a rotation of the slurry inside of the cyclone begins, causing centrifugal forces to accelerate the movement of the particles towards the outer wall. The particles migrate downward in a spiral pattern through the cylindrical section and into the conical section. At this point the smaller mass particles migrate toward the center and spiral upward and out through the vortex finder, discharging through the overflow pipe. This product, which contains the finer particles and the majority of the water, is termed the overflow and should be discharged at or near atmospheric pressure. The higher mss particles remain in a downward spiral path along the walls of the conical section and gradually exit through the apex orifice. This product is termed the underflow and also should be discharged at or near atmospheric pressure.

Jan 1, 1982

By P. B. Venuto, E. T. Strom, S. A. Dixon, W. F. Johnson, T. C. Vogt

Prior to assessing potential for in-situ leaching, it is advantageous to identify the nature of the probable reactants in the ore horizon, including both the uranium species and those in the gangue material. We report mineralogical data on an areally-broad suite of samples from the Westwater Canyon Member of the Jurassic Morrison Formation in the Crownpoint area of the Grants Mineral Belt. Optical microscope, electron micro-probe, X-ray diffraction, spectroscopic and wet chemical analyses were conducted. In these samples, the uranium occurs predominantly as either coffinite or uraninite. The host rock is arkosic sandstone, comprised mainly of detrital quartz and feldspar. The minerals kaolinite and chlorite are present in claystone clasts and calcite occurs as a cement. Major trace elements include molybdenum, vanadium, iron, selenium and sulfur. Carbonaceous organic material is present in the ore and is intimately associated with the uranium mineral when it is coffinite. Geochemical, pyrolytic and 13C NMR analyses indicate organic material is probably a very mature, coaly-type kerogen derived from plant components.

Jan 1, 1982

By Steven A. Moreno

Geochemical returns from commercial analytical laboratories are often delayed because of postal and other bulk distribution inefficiencies. Consequently, minerals exploration programs are handicapped due to insufficient time for treatment, analysis, and diagnosis of the data. The minerals industry lacks a system for rapid transmission of geochemical data which allows immediate entry into statistical and plotting routines. Over the past three years, Houston International Minerals Corporation (HIMCO) has developed a computer-based system to receive, treat, and distribute geochemical data. In the past two years, Bondar-Clegg (Denver) and Chemex (Vancouver) have developed systems to transmit' data directly to HIMCO via the world-wide Boeing Computer Services (BCS) network. The main benefits to HIMCO have been ten less days for reporting turnaround, ten less days for keypunching, less data handling, accuracy. The benefits to the laboratories have been improved in-house data management, reporting, and HIMCO's increased geochemical activity.

Jan 1, 1982

By Eugene C. Robertson

INTRODUCTION A direct proportionality between the observed displacement of a fault and its thickness of breccia and gouge has been proposed recently (Robertson, in press). To validate this finding, an explanation of the mechanics of continuous breccia formation is needed and is offered in this paper. A summary of evidence for the finding will show why an explanation is needed. The correlation between fault displacement [d] and accompanying breccia- plus-gouge thickness [t] seems to be linear and reasonably well established over 6 orders of magnitude, with a range in [d] from 1 mm to 1 km, on a trend of [d/t]= 100, shown in Figure 1. Most of the points are for faults observed underground in mines. The [d] – [t] relation is limited to normal and reverse faults, that have a flat to steep dip and a displacement less than 5 km. It is not applied to large strike-slip and low-angle overthrust faults, whose displacements and breccia thicknesses are widely variable and uncertain. Undisplaced jointed rock is not included in the thickness measurement. A complete description of sources and analysis of the data is given in Robertson (in press). One would intuitively expect that continued movement on a fault would grind up the previously formed breccia and gouge and not produce any more, but the evidence (Fig. 1) indicates otherwise. A physical model to explain continuous formation of gouge and breccia from the wall rocks can be obtained from laboratory experiments on friction.

Jan 1, 1982

By Duk-Won Park

The stability problems of back- filled spoil banks became more important since the Federal Surface Mining Control and Reclamation Act of 1977 was enacted. The material properties of spoil banks were categorized as the first part of the study and spoil slope stability was evaluated using computer programs as a second part. Emphasis was placed on the effects of natural barriers, which is required in the federal law.

Jan 1, 1982

By J. J. Gillman

"The coal deposits from Cape Perce on Cape Breton Island have been known to supply the coal requirements of the people living in or visiting the area for close to 300 years.A major block of coal has been identified off Cape Perce, which has several seams from which coal can be taken. The initial development by the Cape Breton Development Corporation will be in the Harbour Seam and constitutes the Donkin-Morien Development Project.The CBDC's confidence in this indicated resource is based on its knowledge of the Sydney Coal Field and from boreholes driven into the block during the summers of1977, 78 and 79. In 1980, further geological data were gathered from surface drilling and an intermediate-depth high-resolution seismic survey. The surface facilities for the Donkin-Morien Development Project will be located on the northern half of the cape, with access declines extending 3.9 km in a north-northeasterly direction to the Donkin block of coal reserves. The development has the potential of supplying all the coal needed f or the future electrical power generation requirements of Nova Scotia for many years to come.The planned mine, for which a project definition study has recently been completed, will have a production rate in excess of 3 million tonnes per year.IntroductionAt the Second CIM District 1 Meeting held in Halifax in October 1980, a background paper on Phase II of the Donkin-Morien Development Project was presented. The project involves a 3.2-million-tonne, saleable, underground coal mine. At that time, the chronological sequence of events had unfolded, starting with the initial boreholes through to the feasibility study, and on through site clearing and site preparation. This led to engineering design contracts for the portals and the two tunnels to be driven to intersect with the Harbour Seam close to 4 km from their entry point."

Jan 1, 1982

By S. K. Kawatra

With the increasing importance being placed upon modernizing the coal industry as a result of recent developments in the international energy balance, computer control has been and is being instituted in many coal cleaning plants. Control techniques that are well established in many base metal industries have been adapted to coal washing. Essential to any control scheme is an accurate measure of the parameter which is to be controlled. A sensor is required that will provide information both quickly and precisely. In fine coal circuits, the critical parameter that must be measured and controlled is the per- cent ash contained in the clean coal product and tailings. Measuring the ash content of these slurry lines on a continuous basis enables the operating conditions in the circuit to be adjusted so as to obtain optimum separation efficiencies at all times. An on-line ash monitor has been developed and tested at Michigan Technological University which is capable of making percent ash and percent solids determinations instantaneously. Two radioisotopes are employed in this system to generate signals that can be related to the density and the ash content of the slurry. Such data provide a means to execute a short term control strategy.

Jan 1, 1982

The effect of addition of a flotation collector (dodecylammonium chloride) on grinding of quartz has been studied. The data obtained are correlated with the results of tests conducted under similar chemical conditions to study influence of these additives on relevant basic sub-processes (primary breakage, pulp fluidity, and dispersion and flocculation of ground products). Such correlations suggest that the role of chemical additives in grinding is determined by their cumulative influence on the above mentioned basic properties of the system.

Jan 1, 1982

By Adrian C. Dorenfeld

Concentradora "Doña Aida" (100 t /d capacity) was built in 1971-72 to treat dumps and ores containing mixed oxide-sulfide copper-gold-silver minerals derived from two veins. The veins, Don Felipe and Maria, are about 150 m apart, but are distinctly different mineralogically. The deposits are near Sun Juan de Guadalupe, Durango, Mexico. All new process equipment was manufactured locally, in or near Torreon, Coahuilu. Sampling, ore testing, flowsheet design, plant design, drawings, purchasing, financing, and construction, etc., were planned and directed by two engineers. Construction was executed by local miners and common labor (largely agricultural). The paper presents detailed costs for equipment and construction. The subsequent breaking-in operation is discussed.

Jan 1, 1982

By George S. Koch

Since 1882, world zinc production has increased. In contrast, US zinc production rose until about 1915, but since then has remained nearly constant, with a slight tendency to decrease. Production from the Tri-State district, the largest early source of zinc in the US, has gone down steadily; this decline has been balanced by a growth in the rate of other districts. These changes in US production are due to economic, not geological, factors. Recent exploration has located large minable ore bodies: additional deposits will undoubtedly be found in the stratabound carbonate rock and volcanogenic environments. A statistical analysis of the exploration effort in the Middle Tennessee district indicates that new discoveries can be expected there. Thus, the US is in an early stage of the production cycle for zinc. Of major mining districts in the US, only the Tri-State is exhausted under current economic conditions; large zinc resources of low-grade material, which would repay mining at higher prices or improved technology, are known to exist in that district .

Jan 1, 1982

By Seth C. Schaefer

The Bureau of Mines investigated thermodynamic properties of Mn304 (manganomanganic oxide) and Mn203 (manganese sesquioxide). The standard Gibbs energies of formation (?Gf°) of Mn304 and Mn203 from their lower oxides were determined with high-temperature galvanic cells using stabilized Zr02 (zirconia) as the electrolyte. Potential measurements were obtained for the cell Pt, MnO, Mn304//Zr0 2//02(g, 0.0112 atm), Pt, with the overall cell reaction 6Mn0(c) + 02(g, 0.0112 atm) = 2Mn304(c), where- 02 refers to indicated partial pressure of oxygen at the reference electrode. Similar measurements were obtained for the cell Pt, Mn304, Mn203//ZrO2//02(g, 0.0115 atm), Pt, with the overall cell reaction 4Mn304(c) + 02(g, 0.0115 atm) = 6Mn203(c). Equilibrium oxygen pressures for the Mn0-Mn304-02 and Mn304-Mn203-02 systems were measured and may be expressed for the respective systems as [23,400 109 P02 T + 11.91 (764.9 - 1,208.6 K) and log p02 = - 11,957 + 9.66 T (968.6 - 1,208.2 K),] where pressure (p02) is in atmospheres and temperature (T) is in kelvins. Standard thermodynamic properties of Mn304 and Mn203 were derived from these measurements and auxiliary thermodynamic data from the literature.

Jan 1, 1982

By Ingham PD

Selection of equipment for a mining operation, such as Mount Isa Mines, requires certain parameters to be correctly defined. Management control is essential for monitoring, improving and future purchase of equipment. Some research is being done independent of supply manufacturers. Observations about future outlook are made.

Jan 1, 1982

After nine years of negotiations, the U.N. Conference on the Law of the Sea approved a Law of the Sea Treaty text in April. Israel, Turkey, the United States and Venezuela voted against the text and 17 other nations including Belgium, the Netherlands, Italy, the Soviet Union, the United Kingdom and West Germany abstained. These nations still have the option of joining the treaty when it is opened for signing in December. However, the Reagan Administration has stated that several provisions of the deep seabed mining portion of the text are unacceptable and it seems unlikely that the United States, at least, will change its position. ALUMINUM Reynolds Metals Co. has criticized an Oregon state plan to relax air pollution standards for aluminum plants. The company feels that relaxation of the rules does not go far enough. Reynolds officials say that they have spent about $31 million at their Troutdale plant for state-of-the-art pollution control equipment, and if they are required to make the pollution reductions called for in the 1986 rules, Reynolds would be forced to close the 40-year-old plant.

Jan 1, 1982

Esso Australia Ltd. operates a large natural gas producing system in the Gippsland Basin, supplying gas to the Gas and Fuel Corporation of Victoria, the State Electricity Commission of Victoria and several industrial customers. Gas reaches the Longford processing plants from three offshore platforms via a network of large diameter pipelines, which must be protected against the formation of ice-like hydrates. When gas production commenced in 1969, methanol was used to inhibit hydrate formation in the offshore pipelines. However, later investigations showed that the methanol was causing excessive degradation of molecular sieve in the onshore gas-processing plants. (Molecular sieve is used to remove water and H2S from the gas prior to further processing to remove heavy hydrocarbons.)

Jan 1, 1982

Underground mining of the ore below the West Lyell open cut commenced in 1972 with the 10 Series stopes above rail haulage level. The third lift of stoping (30 Series) com- menced this year, and access to the 40 Series stopes is being developed. The method uses transverse open stopes with subsequent mass blasting of the rib and crown pillars and consequently there is sub- sidence and caving of the old open cut area above.

Jan 1, 1982

By James H. Redyke

In August, 1980, while finishing construction of the new stack, one of the flues mysteriously collapsed, killing three people and injuring several others. Several months later a British international steeple-jack company was hired to demolish the remaining portion and make a detailed inspection of the balance of the chimney. During this contract almost one hundred core samples were taken from all parts of the structure including the 32-inch thick base. As the result of these tests and the investigation, the Power Company decided to demolish the complete structure. Because of the critical time element, the decision was made to use explosives in the removal of the structure. To give you some perspective as to the size and dimension of the stack, it was 900 feet tall, 80 feet in diameter at the base, and 70 feet in diameter at the top. The two remaining flues were 25 feet in diameter and extended 30 feet beyond the top slab of the chimney. The outside of the structure was referred to as a wind shield. The lower 120 feet were 32 inches thick and the remaining 780 feet were 12 inches thick. The decision was made to prepare and shoot the chimney at the 120-foot elevation because the debris from the collapsed flue was confined in the base section and could not be easily removed. After extensive and costly engineering, we determined it was necessary to construct steel columns to bear on the lower 120-foot section, which would act as a hinge and guide during the dropping of the structure.

Jan 1, 1982

By Marcel Vanpee

Eight extinguishing powders KCI, were tested on five types of diffusion flames. The effect of flame temperature on the inhibition efficiency was investigated by varying the oxygen index of the flame supporting atmosphere. Inn addition a spectrographic investigation of powder flame dissociation products was carried out on the methane/air/ABC (NH4H2PO4) flame. Dissociation products for this flame included P0, PH, NH, and Na. It is concluded that the main factor to be considered in the efficiency of tie powder is the flame temperature Purple K (KHC03) was typically inefficient in low temperature flames and very efficient in high temperature flames. On the other hand, ABC (NH4H2PO4) was found to lose its efficiency at high temperature but to be quite efficient in the low temperature flames. The effect of temperature is offered as an explanation of the poor efficiency of Purple K (KHC03), against coal dust explosions as contrasted to the high efficiency of phosphate salts against coal dust explosions.

Jan 1, 1982

By Chris Mills

El papel de la separacion gravimétrica en la industria minera es brevemente considerado en perspectiva. Las pruebas e intentos de laboratorio y mineralógicas para el diseñio de los procesos gravimetricos son examinados poniendo especial énfasis en la selección de la tecnologia del proceso. Es tratado y comentado el material disponible en equipos para pequeña escala y trabajo de pruebas-piloto, particularmente en relación a la escalacion y a la adquisición de datos precisos y fiables. El transporte del comportamiento de los datos desde la planta piloto a la planta a escala es igualmente explicado. Son resefiados todos los tipos de equipos a escala total existentes para la separacion gravimétrica, poniendo de relieve las unidades de alta capacidad. Es considerada la disposicion de la planta y la seleccion de 1os equipos auxiliares.

Jan 1, 1982

By Duk-Won Park

The PSU/MVS program, one of the computer programs for ventilation network analysis most recently developed at The Pennsylvania State University, was applied to the analysis of modifications to an existing ventilation system for a coal mine located in southern West Virginia. The program is well designed and has diversified capabilities which allow the users to make decisions on the optimum size and number of fans, the location and number of airshafts, and the optimum operational procedures. The mine had 10 working faces, from which the average production rate was about 5900 tons of clean coal per day. Two vane-axial mine fans were used in parallel at a shaft, and both of them operated simultaneously. One additional shaft was in the final construction stage and it would be used in four months to alleviate the load for the existing fans and distribute intake air more evenly. The overall ventilation surveys, including the altimeter pressure survey and the air quantity survey, were carried out in the mine entries, shafts, slopes, and gob areas. Computations were made using the above-mentioned computer program on the present condition and after one additional fan was placed in operation at the new shaft. Also, recommendations were made on the air route and fan blade settings for the most economical and efficient ventilation system. Further studies were carried out to decide the proper period when the third air shaft would be required according to the long-term mining plan. Additional branches were added for the next 4 years of the production plan, and the ventilation conditions were tested at the end of each year. Numerous combinations of blade settings and modifications of air routes were tested. It was recommended that the third air shaft be added at the end of the third year so as not to experience fan stall.

Jan 1, 1982

By P. A. Witherspoon, Y. W. Tsang

Normal stress-fracture closure variation and stress-dependent fluid flow rates were calculated for rock fractures of different aperture distributions. This study shows that both the mechanical and hydraulic properties of the fracture are controlled by the large-scale roughness of the rock fracture. Hence the typical large-scale undulation wavelength of the rock joint dictates the suitable sample size to be used in normal stress and fluid-flow measurements, if results due purely to sample size are to be avoided.

Jan 1, 1982