Search Documents

By A. G. R. Coreejes, G. Ferreira

The paper sets out briefly the methods used for the planning and control of the construction work at Grootegeluk Coal Mine near EIIisras, Transvaal. It includes a discussion of the programming, the updating of programmes, and the progress reporting.

Jan 1, 1982

By David C. Grant

During in situ uranium mining using ammonium bicarbonate lixiviant, the ammonium exchanges with cations on the ore's clay. Mter mining is complete, the ammonium may desorb into post-leach ground water. For the particular ore studied, other chemicals (i.e., uranium and selenium) which are mobilized during the leach process, have also been found in the post-leach ground water. Laboratory column tests, used to simulate the leaching process, have shown that aluminum chloride can rapidly remove ammonium from the ore and thus greatly reduce the subsequent ammonium leakage level into ground water. The aluminum chloride has also been found to reduce the leakage levels of uranium and selenium. In addition, the aluminum chloride treatment produces a rapid improvement in permeability.

Jan 1, 1982

By John K. Dienes

The permeability of sands and soils seems to be adequately de- scribed by Darcy's law, but the permeability of rocks is complicated by a number of factors related to the probability of crack intersections. During the last few years we have developed a statistical theory of fragmentation which has been successful in explaining the observed behavior of rocks. In this paper, a theory of permeability is developed which draws on the concepts employed in previous work. The permeability involves three factors, the average fluid flux per crack, the number of cracks per unit area, and the fraction of cracks that are not isolated. Probabilistic ideas are used in connection with the hydrodynamic theory of flow through a single crack to develop an integral expression for permeability. The result has the form of Darcy's law for anistropic media. Although the current work is motivated by the need to develop optimized oil-shale retorts, we believe that the theory can be applied to a variety of other problems.

Jan 1, 1982

By Gordon M. Pugh, David G. Rasmussen

INTRODUCTION Sublevel long-hole stoping is a large tonnage stoping method that may be used when there is a fairly com¬petent straight vein and the walls will stand with little support. It is a method that lends itself to a high degree of mechanization. Two variations of the method are illustrated in Figs. 1 and 2. Fig. 1 illustrates development typical for a 3-m (10-ft) wide vein. Initial development is by a lower haulageway, which may be either track or trackless. A two-compartment raise is driven in the footwall of the vein. At about 12 m (40 ft) above the main head¬ing, a footwall scram is driven and pockets through the vein are cut on 7.6-m (25-ft) centers. Each of the sub¬level blocks selected in this example is 45.7 m (150 ft) long by 12 m (40 ft) high. Stoping starts at the slot raises at stope endlines and retreats to the timbered raise. This retreat sequence starts on the lowest sublevel and the opening cut is blasted into the slot raise. This retreating system is used in order to provide a good safe back over the miners working in any given sublevel. A crawler-mounted down-the-hole or conventional pneumatic drill puts the holes down from one sublevel to the next on any desired drill pattern. Gravity flow brings the broken ore down to the scram level. The illustration shows a large slusher mounted at the timbered raise and slushing from the pockets back to the raise chute. Development of the ore block in Fig. 2 is typical for a 5.5-m (18-ft) wide vein. Initial development is by a trackless heading driven in the footwall of the vein. Pockets are then put into and through the vein on 7.6-m (25-ft) centers. For ease in using trackless rubber tired mucking equipment, these pockets are crosscut to the vein at approximately 1.04 rad (60°) rather than per¬pendicular. A two-compartment timbered raise is driven down from one level to the next. Endline slot raises are again put through from level to level. Each of the sub¬level blocks selected in this example is 40-m (130 ft) long by 33.5 m (110 ft) high. Stoping starts at the slot raises and retreats back to the timbered raise. Long holes are drilled from one sub¬level down to the next by starting between the lowest pair of sublevels and then working up the ore block. Mucking out of the pocket drawpoints is accomplished by rubber-tired load-haul-dump (LHD) units which then dump into a centrally located orepass.

Jan 1, 1982

By Robert B. Schluter

The Bureau of Mines investigated separating copper-nickel mattes to recover a copper-rich fraction suitable for processing by conventional copper metallurgical processes and a nickel-rich fraction suitable for processing in a hydrometallurgical nickel circuit. Distribution of cobalt and precious metals between the copper and nickel fractions was also determined. A matte containing a nominal 65 pct Cu, 9 pct Ni, 4 pct Fe, and 20 pct S was separated into a copper fraction that comprised 80 pct of the matte weight and contained 70 pct Cu and <1.5 pct Ni, plus a nickel fraction that contained 40 pct Ni and 30 pct Cu. Recoveries of copper and nickel into their respective fractions were 90 pct and 87 pct. These results were obtained in a laboratory flotation cell at a matte grind of 90 pct minus 500 mesh and a pH of 12.4, using 1.7 pounds DPG (diphenylguanidine) per ton of matte as collector and frother. Magnetic separation was used to remove metallic iron-nickel alloy from the copper fractions. Distribution of cobalt was about 70 pct to the nickel fraction and 30 pct to the copper fraction. Silver reported predominately to the copper fraction, while Au, Pt, and Pd were essentially entirely recovered in the nickel fraction.

Jan 1, 1982

By Jan Wolski

Today&apos;s rapidly shrinking world requires a common language of measurements, a consistent system which could be used by everyone. The S.I. system of units is generally accepted as such and is already in use by a great majority of nations in the world. The change to S.I. units is also slowly taking place in U.S. engineering practice. The transition period is difficult and long because it takes time to get familiar with the new system, to start "feeling" values in new units. Instruments, formulas, computer programs, survey grids, etc. have to be converted or exchanged. The transition period should be used not only for substitution of units, but also for rationalization of presently used calculation methods. This paper examines the major parameters of mine ventilation from the above point of view and discusses a system which is much simpler and more consistent than the American Unit System still in use in the United States. In October 1979, the Society of Mining Engineers of AIME decided to introduce the S.I. unit system in all its publications including the periodical "Mining Engineering", and since February 1980 the system has been used consistently, not only in SME publications but in all conferences and meetings organized by this Society. The authors have no intention of explaining the details of the S.I. system in general. Any reader can find this information in many available publications and conversion tables, and in particular in the ASTM Standard for Metric Practice, E380-79. A comparison is made between various units used in mine ventilation from the past and those presently in use. This will allow an easy translation from one system to another, important when reading publications from abroad. S.I. and customary U.S. formulae are shown side by side for easier visualization of similarities and differences. Recommendations for the necessary steps in order to switch from American to S.I. units conclude the paper.

Jan 1, 1982

By Yoginder P. Chugh

It is well known that weak floor conditions in central Illinois affect pillar and mine opening stability. The floor interaction with coal pillars and immediate mine roof are being studied using two dimensional (plane-strain) elastic-plastic finite element models. The effects of varying soft floor thickness, coal seam- thickness, width of mine openings and strength parameters of coal and mine floor are being evaluated. The finite element models developed by Agbabian Associates and Dahl were utilized in this study.

Jan 1, 1982

By Shawn T. Sorrell

Phillips Coal Company (PCC) submitted the first surface mine permit application under the Office of Surface &lining approved regulatory program of the State of Louisiana. This application for the Oxbow Lignite Surface Mine which is located approximately 64 kilometers (40 miles) southeast of Shreveport, Louisiana was submitted in March 1981. The State of Louisiana Office of Conservation, Surface Mining Division, assigned this application number LSM-1, indicating it is the first one submitted in Louisiana history. The permit area for the Oxbow Mine encompasses 6,251 hectares (15,627 acres). Of this total permit area, 5,862 hectares (14,656 acres) were classified by soil type as prime farmland by the U.S. Soil Conservation Service (SCS). Prime farmland acreage in the permit area became a major central issue in our early planning stages and throughout the permitting process of the Oxbow Mine, due to the magnitude of acreage involved.

Jan 1, 1982

By N. B. Strydom, H. H. E. Schroder, A. van der Linde

This paper describes a study of the destination of the mercury that is present in the ore during the recovery of gold. It was found that over 96 per cent of the mercury passed through the process untouched. A small amount finds its way into cyanide solution, and is concentrated with gold in Zinc dust as Merrill precipitate. When the precipitate is calcined, the mercury is driven off and finds its way into the atmosphere. However, dilution of the stack gas in the atmosphere appears to be sufficient to prevent hazardous concentrations arising at ground level. No other significant concentrations of mercury were found at any stage of the process. The amount of mercury lost to the atmosphere by this mechanism appears to be less than 200 kg per year throughout the gold-mining industry in South Africa. Virtually no mercury vapour could be detected in the air in the smelt-house. Slight increases in mercury concentrations above background level were observed in soils around the reduction plants and in the discharge or return waters, but no environmental stress is anticipated from these increases.

Jan 1, 1982

By Ronald W. Utley

INTRODUCTION The &apos;&apos;Do&apos;s and Don&apos;ts" of installing equipment in a comminution circuit begin during the study stage of a proposed project, continue through preliminary engineering, detail engineering, procurement, the actual placement of equipment at the job site, and end with turnover to the owner. Equipment supplied for a modern comminution circuit will be high quality, rugged machinery designed according to appropriate manufacturing standards for long hours of trouble-free service. However, certain precautions and procedures must be observed in plant design and layout, equipment handling, installing and servicing in order to obtain optimum performance. This chapter contains general installation "DO&apos;S and Don&apos;ts" for the major equipment in the circuit. •Primary Gyratory Crushers •Rock Breakers (Hammer) •Belt Conveyors •Apron Feeders •Weigh Belt Scales •Secondary Crushers •Vibrating Screens •Grinding Mills •Mill Liners •Open Gear Sets •Speed Reducers •Electric Motors •Cyclones •Slurry Pumps Some questions will not be covered in this chapter, or may not be applicable to the actual equipment purchased, as requirements do vary from manufacturer to manufacturer. Additional specific information can be obtained by contacting the manufacturer&apos;s local representative or the factory. All inquiries should be accompanied by the following information: •Unit size and type of equipment •Manufacturer&apos;s shop order number (after order placement) •Serial number (after manufacture) DO&apos;S 8 DON&apos;TS FOR INSTALLATION OF ALL COMMINUTION CIRCUIT EQUIPMENT Installation By Design DO obtain tables of weights and clearances from manufacturer. DO obtain WR2 forces from manufacturer to determine that the foundation is adequate. DO determine compression strength of foundation soil and/or rock. DO obtain manufacturer&apos;s recommended typical foundation drawings. If substantial alteration to manufacturer&apos;s drawings is required, check with the manufacturer before proceeding.

Jan 1, 1982

By R. L. Rickel

The Bureau of Mines, as part of its minerals environmental technology research, conducted a study of mine waste tailings disposal. Part of the investigation evaluated the sand bed dewatering technique for disposal of alumina mini plant tailings as a means to increase consolidation rates and contain effluents. The technique employs a bed of sand resting on an impervious bottom. The tailings slurry is impounded over the sand layer and is dewatered through bottom drain piping. The study employed a single 10-ft-high, 6-in-diam, clear polyvinyl-chloride (PVC) column, and thickener wastes from the acid leaching of calcined kaolin clay. Results showed a consolidation rate of 41 in in 186 days for a total volume reduction of 37 pct. Sand bed dewatering was an efficient technique for solid consolidation and effluent containment when compared with data obtained from other dewatering studies.

Jan 1, 1982

By E. L. Smith

The development of larger size flotation machines, which started in the 1950&apos;s and 19601s, is still proceeding. The largest mechanical flotation machines available today have unit volumes in the range of 38 to 42 m3 (1,350 to 1,500 cft). In fact, the motivating forces of increasing capital and energy costs and decreasing ore grades, which created the need for large flotation cells, not only still exist, but are becoming more critical. This paper reports the development of an improved mechanism for these large flotation machines. The starting point in the development of a new mechanism was the identification of design and performance features of existing machines where improvements were desirable. The result of this work was a mechanism which is an improvement over existing designs. This new design is characterized by an efficient overhung stator and a vortex profile rotor. The overhung design of the stator removes unnecessary and undesirable baffling in the lowest parts of the tank, while maintaining a quiescent froth layer. This results in lower power consumption and better pulp circulation and solids suspension. The vortex profile rotor acts as an efficient pump, with higher pulp recirculation rates as evidenced by the increased air dispersion capabilities, good solids suspension, and low power consumption.

Jan 1, 1982

By Leonard J. Prosser, Joseph Cervik, John H. Perry

The Bureau of Mines has developed several techniques for draining methane from coalbeds in advance of mining. Drilling long horizontal holes from an underground location is one such technique, which was successfully demonstrated in the Pittsburgh and Sunnyside Coalbeds. The same technique has now been applied in the Mary Lee Coalbed at Jim Walter Resources, Inc. &apos;s No. 4 Mine, Brookwood, Ala. , where two holes were drilled horizontally--one to a depth of 1,010 feet (308 m) and the other to 540 feet (165 m). The 1,010-foot (3083) hole proved successful in degasifying a portion of the Mary Lee Coalbed. The hole drained methane for 1 year, during which time the initial gas flow of 200,000 ft3/d (5,663 m3/d) declined to 65,000 ft3/d (1,840 m3/d). Total gas production was 40 x lo6 ft3 (1.1 x lo6 m3 ). The gas was of commercial quality, with 98 pct methane and a heat rating of 990 Btu/ft (36.89 Mj/m3). The methane emissions from the faces of the mine section advancing into the degasified zone were reduced by 60 pct. The 540-foot (165-m) hole was terminated prematurely when it became impossible to maintain an open hole. Because of caving, very little gas was drained through this hole.

Jan 1, 1982

By Lee W. Saperstein

P.L. 95-87 contains explicit demands for land-use planning in its reclamation and designation sections. Both sections require recognition of local land-use plans; however, the sections are not well integrated. Accommodations to these planning requirements may be found in suggestions based on British mineral planning practice. Better links can be created among local land-use planners, the state&apos;s permitting authority and designation office, and mine designers. Mining companies should take more interest in local land-use plans and in resource inventories; states should consider devolving to local government responsibility for accepting mine permit applications and designation of unsuitability petitions.

Jan 1, 1982

Agglomeration pre-treatment is a new process now being used here and overseas whereby problems arising with the heap leaching of gold and silver from materials containing critical amounts of fines or clay can be simply and cheaply overcome. The technique involves mixing the material with a suitable binder, commonly Portland Cement, and tumbling the moistened material to agglomerate the fines. These agglomerates are placed on the leach pad and cured prior to leaching. Test results, plant and operating cost data are presented. INTRODUCTION Heap leaching is a low capital and operating cost alternative to conven tional processing techniques for gold and silver extraction. A number of commercial-scale operations have recently started in the United States and the method is being considered for further deposits there and elsewhere.

Jan 1, 1982

By R. P. Plewman

The Chemical, Metallurgical and Mining Society, from which The South African Institute of Mining and Metallurgy is descended, had as its coat-of-arms a green shield with a very flat gold chevron dividing the field into two. A crossed pick and shovel occupied the lower half, and an alembic (distilling vessel) and a flaming crucible occupied the top half.

Jan 1, 1982

By David L. Durler

In-situ uranium mining is a relatively new and innovative method utilized for the commercial extraction of uranium. As with any mining method, however, significant environmental concerns will be evident and must be addressed in a rational and far-sighted manner. Experience has shown that radiological and non-radiological environmental problems may not manifest themselves until after the in-situ methodology has become established and matured to some degree. It is important, therefore, to recognize potential environmental concerns and incorporate them into an environmental program that spans the premining, mining, and post-mining phases of an in-situ operation.

Jan 1, 1982

By Luis Tavares Ribeiro

Dynamic programming is based on the-, application of a simple property formulated by Bellman in his principle of optimality (Bellman, 1957): "An optimal policy has the property that whatever the initial state and initial decision are, the-remaining decisions must constitute an optimal policy with regard to the state resulting from the first decision". The method is charaterised by: (Dowd, 1979) a) A function defining the total value at each decision time of the system. b) The set of permissible decisions. c) The present state of the system. d) The number of steps remaining before the procedure is terminated.

Jan 1, 1982

By George Quackenbos

The principal objective of this Program is the design, fabrication and testing of an Environmental System for operation in underground mines, to assess the effect of various mining systems on the contaminant levels near the mine face and within return airways. In order to determine the effect on airborne contamination in mines resulting from the development of new mining techniques, equipment and control systems, a Comprehensive Monitoring System is required to assess such contamination levels at critical and strategic locations and relate this information with ventilation parameters. The three variables to be sensed on a continuous basis are airborne dust concentration, methane concentration and ventilation air velocity. Each Monitoring Station will consist of a self-contained unit containing a power source and sensors to monitor the three above mentioned parameters. Ruggedness, reliability, ease &apos;of operation and intrinsic safety are important design objectives. Data gathered by each Monitoring Station will be fed to a Central Data Acquisition System by means of a portable transfer unit.

Jan 1, 1982

MR. ENZI: hank you very much. I&apos;m sure there?s a lot of you out there just realizing that Rock Springs and Gillette is not one city. I&apos;m sure there&apos;s a lot of you wondering why a person from a town who has the image in the national media that the town of Gillette has is talking to you about image. I had a person this morning ask me if Gillette wasn&apos;t the end of the world. The only response I can give is "no, but you can see it from there." We have been researched a lot and, I realize, we&apos;ve been very lucky because I&apos;ve observed that researchers cause cancer in rats. In fact a wonder drug is one that has no effect on mice. In fact I&apos;ve been thinking of posting a sign in my office that would read "due to the large number of interviews by journalists who already have their articles written, we would most respectfully request that anyone wishing to insult the city of Gillette, please limit themselves to 3,000 words or 15 insults, whichever is shorter." I don&apos;t know if any of you saw the article in Playboy about three months ago on the city of Gillette. What you probably don&apos;t realize about that article is that that was an attempt by Playboy magazine to see if they couldn&apos;t change their image to a national municipal magazine. I think it&apos;s important to know Gillette is the frontier city, a pioneer city, it&apos;s a shopping center for northeast Wyoming and most importantly, we&apos;re the energy capital of the nation. We&apos;re on the threshold of the Powder River Basin and we will be the nation&apos;s energy solution. Besides coal, we&apos;re, already the heart of the state&apos;s leading oil producing area and we have vast uranium resources. But I, want to tell you the biggest resource that we have is, the people who have come to live in Gillette. You will find Gillette a busy, young, pulsating community. We&apos;re experiencing the excitement of growth. We&apos;re welcoming a higher percentage of newcomers than any other town in the nation. Yes, growth to us is exciting. Where else can you get ten years of experience in two years? We realize you can&apos;t maintain the status quo. Growth can be painful but not as painful as the alternative, recession and depression. For a little bit of background, we are now at 16,000 people and we have another 4,000 people who live on the outside but look like they live on the inside. The Census Bureau says that we have, 11,225 people but we have that many people in a traffic jam on the Douglas Highway in one day. I?ll , tell you about a few things happening in Gillette. I think it&apos;s very important to emphasize that I didn&apos;t , do these things; it&apos;s the youth and the energy of the community that has done these things. Right now the city of Gillette has 32 major projects underway. We have water for 50,000 people and we&apos;re seeking more water. The city in 1975 was 1 .8 square miles. Last year alone we annexed I square mile. We build 10 miles of paved streets a year. For the last 8 years we&apos;ve doubled our parks&apos; budget. I

Jan 1, 1982