Search Documents

By Lok W. Home

HISTORICAL DEVELOPMENT At the beginning of the 1970 more than 90% of pro¬duction drilling in open-pit mining was obtained with the use of rotary drills. At the same time, the use of rotary drills underground was virtually nonexistent. Several progressive mines began questioning whether efficient rotary drilling could not be adapted to under¬ground applications. In the late 60s and early 70s at¬tempts to use rotary drilling were made by Inco, Ltd. and Meramac Mining, utilizing drill units designed as a combination of small diameter raise drills and rotary drills. These initial attempts were unsuccessful primarily due to the immobility of the equipment and low degree of dependability. At the same time, experiments con¬ducted by Inco and Meramac using large diameter in¬the-hole percussion drills produced immediate encourag¬ing results. The first serious attempt at utilizing rotary drilling underground was made by Texasgulf in 1971 at Kidd Creek mine in Canada. An experimental stope 15 m wide, 36 m long, and 30 m deep was drilled using 200-mm diam rotary drilled holes. The machine used was a Robbins' Model 11 D. The Model 11D is a rotary drill designed to drill drain and utility holes under¬ground. The results of this test revealed that large diameter blasthole stoping was feasible. The indications were that the major areas of concern-fragmentation and pillar damage-could be controlled and a new low-cost stoping method resulted. At this point Texasgulf and Robbins entered into a cost-sharing agreement to develop a rotary drilling unit specifically for this stoping method. Drilling of the trial stope required pouring a concrete pad at each drill hole plus anchoring the derrick to the pad by means of rock¬bolts. Utilization expressed in terms of drilling time to available time was less than 20%. It was obvious that the required unit had to be mobile, setup time had to be minimized, and rod handling had to be improved. The first attempt at an underground production-type rotary drill consisted of mounting the basic 11D on an air-powered Eimco 600 Series crawler. The crawler was equipped with four screw-type leveling jacks operated by an impact wrench; rod rack facilities for 60 m of 1.2-m long, 170-mm diam rods; a rod handling facility consisting of an air-lift swing boom and a pipe loader which automatically positioned the rod under the float¬ing drive box; a turnbuckle anchor system requiring in¬stallation of four rockbolts in the drill drift floor and placing turnbuckles from the rockbolts to the corners of the drill; and trailing power units containing the electrics and hydraulics required to operate the drilling unit. Operation of this unit revealed a vast improvement in drilling time but some problem areas remained. The anchoring system required secondary drilling and proved difficult to adapt to the localized irregular floor surface and the trailing power unit was difficult to maneuver and was causing unnecessary maintenance costs. Addi¬tional improvements resulted in the standard 11MD rotary blasthole drill. DESCRIPTION OF UNIT This standard model consists of the drill and the power unit integrally mounted on an air-powered crawler chassis (Fig. 1). The rod-handling and leveling¬jack systems are similar to those used on the prototype Texasgulf unit and remained relatively the same. The anchoring system has been replaced by the roof jack, initially screw type but now hydraulically actuated. The anchoring system is necessary as the drill exerts more thrust than the weight of the unit. During operation it is found that the two front jacks adequately anchor the machine. The complete unit's operational dimensions are: height, 3.2 m; width, 2.1 m; and length, 4.2 m requiring a 3.5- x 3-m drill drift. The derrick is pivot mounted and raised and lowered by a hydraulic cylinder reducing the transport height to 2.5 m. The derrick is also turnbuckle mounted to allow dip angle drilling from vertical to 0.52 rad (30°) off vertical. The drill derrick can be mounted to allow dip axis to be parallel or perpendicu¬lar to the long axis of the unit. The standard rods are 1.2 m in length and are contained in racks of 10 which can be removed for transportation. Drilling torque is produced by a 56-kW (75-hp) electric motor driving a double vane pump which in turn drives a Robbins high torque gear-type hydraulic mo¬tor. In addition to the hydraulic motor, the machine drive system has a 3.9:1 planetary gear reducer. This results in six speeds with the following minimum and maximum range: Maximum rpm 112 Torque 3725.5 J (380 kg m) Minimum rpm 10 Torque 14 706.0 J (1500 kg m) Drilling thrust is provided by two bootstrap cylin¬ders pressurized by a variable volume pump. This sys¬tem can produce from 0 to 267 231.2 N thrust in either direction. Bailing air (approximately 17 m3/min at 382.2 to 490.3 kPa) is introduced through a rotary swivel pass¬ing directly through the center of the drive system to keep efficiency and losses to a minimum. Hole annulus is also kept to a minimum by using 170-mm rod when drilling a 200-mm hole. A small amount of water is added to the air for dust suppression. The machine has to be supplied with air, water, and electrical power. It does not appear feasible to provide an integral air power supply with the rotary drill such as is done with open-pit rotary drills. Air is required and installed during the primary development of the drill drift. The machine can be adapted to drill hole diameters from 170 to 228 mm for blasthole operations. The drill string consists of the rotary bit, crossover stabilizer, roller stabilizers, and standard rods. The operator controls speed and thrust pressure from an operating console which can be mounted in a conve¬nient position. Mount Isa has made an adaption to the operating console to permit remote collaring of drill holes in an uncleared floor.

Jan 1, 1982

By Francis R. Redfern

Newton's method of solving a nonlinear equation is employed to develop a least-squares acoustic emission source location method in which the spatial residuals of the location equations are minimized. These residuals, related to the distances from the least-squares source location perpendicular to the surfaces described by the location equations, permit location error to be estimated to first order along the spatial axes. The solutions obtained by this method are the best spatial solutions to the location equations in the least-squares sense. Also presented is a procedure by which the geometrical control of a transducer array can be evaluated using the rate of change of source location with fractional velocity change.

Jan 1, 1982

Jan 1, 1982

By Otto Engel

"A multipurpose program for a hand-held programmable TJ-59 calculator and PC-100C printer facilitates the evaluation of various mineral processing tests and the calculation of mass and metal balances. Its application is demonstrated by some example problems. Detailed user instructions are given for each application.IntroductionThe program listed in Appendix I is written for a programmable Texas Instruments TI-591 PC-100C calculator I printer combination. The program is applicable for the evaluation of:1) screen analyses;2) flotation test s; and3) mass and metal balances.Each application is demonstrated by an example problem and corresponding detailed user instructions. The ""measured"" data in the examples are fictitious and do not represent a real operation.The steps in using the program are the same for each of the three types of application, viz.:1. Enter the number of product fractions and press ""A"".2. Enter the measured weights (0) of each fraction and press ""RIS"" each time. After the last fraction has been entered, the printer automatical1y displays the total weight.3. Press ""B"" to calculate the weight distribution (Y). Once ""B"" is pressed, the printer automatically displays the weight distribution of all fractions.4. If the accumulated weight distribution (EV) is also needed, press ""RIS"". The printer now displays these data. This step is optional and may be bypassed.5. Press ""2nd A"" to prepare for entering of the measured metal assay (M).6. Enter the measured metal assays of each fraction and press ""RIS"" each time. If analytical data exist for more than one metal, each data set has to be entered separately in one sequence.7. Press ""C"" to determine the ""calculated"" head assay (MA) of all fractions.8. Press ""RIS"" to calculate the metal distribution (R). Once ""RI S"" is pressed, the printer automatically displays the metal distribution of all fractions. This operation is optinal and may be bypassed if desired.9. Again press ""RIS"" to obtain the accumulated metal distribution (ER). This operation is optional and may be bypassed.10. Press ""D"" to calculate the gangue distribution in the concentrate (W). One ""D"" is pressed, the printer automatically displays the data for all fractions. This operation is optional and may be bypassed.11. Press ""RIS"" to obtain the accumulated gangue distribution (EW). This operation is optional and ma y be bypassed.12. For more than one metal, press ""E"" to clear the memory for storing the assays of the next. Then press ""2nd A"" and start entering the assays of the next metal as described previously (6 to 11). Steps 5 to 12 may be repeated as many times as desired."

Jan 1, 1982

By William J. Taylor

Strictly defined, a stull is an inclined or horizontal timber support; a vertically placed timber is defined as a prop. Common usage allows the catchall term "stull" to refer to all such uniaxial mine support, regardless of orientation. Typically a stull is a round wooden column that is wedged in place to provide short-term auxiliary support between sill and back, or between hanging wall and footwall. Stulls may be used exclusively or in con- junction with other support systems such as roof bolts, shotcrete, or cribbing. Stulls are used both as local temporary support in stoping operations and for uniform systematic support installations. Where stoping areas are to be abandoned soon after excavation, stulls may be used to provide temporary support during mining operations. Where controlled caving and subsidence is required, stull supports are designed to fail in a systematic, predictable manner. Wood type is selected on the basis of availability, price, and load carrying characteristics. Coniferous woods are typically used, especially to carry heavy ground loads. Brittle woods are generally avoided because of their tendency to fail suddenly. Gradual yielding failure is preferable to sudden, unexpected failure of the support. Some usage of wood from deciduous trees such as cottonwood and other poplars has been reported in Grants, NM. These stulls reportedly mushroomed as the ground load increased but continued to maintain their structural integrity. Stulls fabricated from structural steel are used in special applications. Adjustable lengths are commercially available in mechanical, hydraulic, and pneumatic designs. The high cost of mechanical stulls limits their use to mining systems where recovery and reuse is possible. End blocking, also called headboards or footboards, uses wood blocks that are placed between the stull end and the ground they are supporting. The blocks are typically 50.8 to 101.6 mm (2 to 4 in.) thick, 203.2 to 304.8 mm (8 to 12 in.) wide, and 381 to 609.6 mm (15 to 24 in.) long. End blocking serves to distribute the support over wider back area. Compression of the end blocking gives visual indication of wall movement prior to failure of the stull. A common application of the stull is in flat-bedded uranium mining during pillar extraction. Many western US uranium mines use a pillar pattern development to delineate the irregular ore pods. After development of an appropriate sized pillar, the ore pillars are then sequentially mined out, leaving the undercut hanging wall or back to cave. Where thickness of the ore is less than 4.3 m (14 ft), stulls are generally used to provide ground control as the pillar is removed in slices. Experience dictates the density of stull placement. In general, the number and size of stulls should be sufficient to resist ground closure and to provide support for drilling and loading operations adjacent to the pillar. Stulls next to the mining face are often lagged 0.9 to 1.2 m (3 or 4 ft) up from the floor (or sill) to confine the blasted ore to a passage next to the pillar. Mucking is simplified by this confinement. Experience dictates whether back control along a mining face requires removal of stulls to allow con- trolled subsidence of the back or hanging wall. Without caving or closure, abutment pressure can create poor ground conditions near the pillar.

Jan 1, 1982

By Fraser M. Walsh

The objective of this program was to determine by laboratory experiments the kinetics and mechanics of the reactions that produce acid in coal mine drainage. The program was divided into three phases: In Phase I, five coil mines, representative of Appalachian coal mines, were chosen for sampling and an experimental design was identified suited to accomplish the program objectives. In Phase II, the five mines were sampled and test protocols applied. The results showed most pyrite weathering to be based on oxidation in the presence of water. Iron bacteria, especially Thiobacillus ferrooxidans, catalyzed the rate of pyrite weathering by a factor of three. An increase in initial iron concentration in a system that modeled the nine environment acted to inhibit bacterial catalysis of weathering. In Phase III, five tailings piles were sampled and the material obtained was used to evaluate this method of bacterial catalysis inhibition. The evaluation verified method effectiveness; inhibition of over 80% of the release of weathering products was observed.

Jan 1, 1982

By William L. Jude

INTRODUCTION Although the mining method described in this chapter is locally designated "modified Mitchell," there are so many features which are characteristic of square sets that the designation "modified square set" would describe the method equally well. The method was developed as a result of local operating experience with various mining methods, observing operations in mines in the southwest where Mitchell stoping had been thoroughly developed, and an exhaustive study of min¬ing methods literature. Since 1941, modified Mitchell stopes have con¬tributed over 50% of the total stope production and were largely responsible for supporting production dur¬ing the war years and period of declining manpower and increasing costs. GEOLOGY The community of Gilman is situated on Battle Mountain at an elevation of 2743 m (9000 ft) in the Battle Mountain mining district, about 45 km (28 miles) by highway north of Leadville, CO. The sur¬rounding area, including the Mount of the Holy Cross and Eagle River Canyon, is noted for its beauty and recreational facilities, both summer and winter. Massive sulfide ore bodies of the limestone replace¬ment type occur as chimneys and mantas or as blankets in strata dipping 0.19 rad (11°) northeasterly. A chimney is shaped like an inverted cone with shale, quartzite, and porphyry caprocks forming its base. This relatively impervious capping apparently blocked rising ore constituents which formed the chimneys and mantas. At the apex or lower extremity of the chimneys, the ore follows small fractures and bedding planes in under¬lying quartzite. Dimensions of chimneys vary, ranging up to 61 m (200 ft) vertically and 76 m (250 ft) horizontally near capping. The manta or blanket ore bodies vary in vertical cross section from one hundred to several thousand feet. One such manta was developed from its outcrop to its chimney source approximately 610 m (2000 ft) downdip. Another manta of substantial cross section and length did not follow shale but extended updip with limestone capping from its source at a lower horizon. All chimneys, however, make up to the shale¬quartzite-porphyry capping. Chimney ore minerals are mainly pyrite and chalco¬pyrite with accessory copper and silver minerals, surrounded by, and in places overlain with, marmatite, pyrite, and galena. Manganosiderite extends into the ore. It may or may not be impregnated with sufficient marmatite and galena to be of commercial grade. Ore may be massive, coarsely crystalline, or sandy, some¬times rubbly. Generally speaking, chimney ore masses are incompetent and of variable grade. Caprock is heavy and caves readily. Manta ore minerals are mostly marmatite, pyrite, and galena associated with manganosiderite. Structural characteristics of the ore are similar to those found in chimneys and where the manta contact shale capping the ground is unusually heavy. However, the large manta with limestone capping mentioned previously consisted of a hard strong ore mass in fairly strong host rock. Commercial ore contacts are fairly regular in this manta but in others the ore waste contacts along the walls are irregular with shaly limestone pendants extend¬ing downward into the ore at capping. Dolomite sand is also quite frequently encountered along wall contacts and less frequently overhead. MINING METHODS Practically all stoping in the Gilman ore bodies has been carried on with timber and fill methods and the features which have been briefly described have dictated the choice. Although at the present time modified Mitchell and underhand square-set stopes account for the total production, considerable production has been obtained from alternate horizontal cut-and-fill stopes with Mitchell truss stopes in the pillars. This method was highly satisfactory in the hard manta ore body mentioned earlier and where ore excavations 11 m (35 ft) wide and 23 m (75 ft) long required no auxiliary timber support. It was a pillar recovery application of the method devised by M. W. Mitchell at the Calumet

Jan 1, 1982

By Kot F. Unrug

Since the introduction of longwall systems, the prediction of roof behavior and support requirements have become the major issue referring directly to safety as well as productivity. In more recent times, and especially in the USA where longwalls are exclusively equipped with costly hydraulic self- propelled support systems, a decision whether a longwall is applicable in a given condition, and when so, what kind of equipment should be selected, is of primary importance. There are numerous examples where lack of experience, and subsequently wrong selection of supports or winning machines, resulted in considerable losses. It should be emphasized that careful studies of prevailing geological and mining conditions, especially in a new area, are required to assure a successful operation. An evaluation of the conditions can be carried out in different ways utilizing such methods as: - Theoretical approach. applicable when geological conditions comply with the theoretical assumptions. - Empirical relationship which gives satisfactory results where the coefficients could be adequately determined. - Structural geological studies which must be undertaken in all cases, since the frequency of fractures and their orientation have a prevailing influence on roof behavior. - Scale model study on equivalent material for determination of failure conditions in the roof and mechanism of movement (flow) of broken rock matter. Coefficients for empirical formulas can be determined by these types of studies, as can boundary limits for mathematical modeling. - Mathematical modeling, e.g., finite element analysis. - Measurements and observations taken underground during the development period end utilization of experience for previous longwall panels in the area. Usually it is the most practical method where mining and geological conditions are comparable. An application of me or more of the above approaches remains to be a matter of judgement for particular conditions, however, the utilization of a practical experience, when available, is usually the safest way for planning a successful longwall operation.

Jan 1, 1982

By C. M. Brown

Selection criteria for the instrumentation employed in semi-autogenous grinding circuits are reviewed. Instruments in use for grinding mill and related process equipment start- up, shutdown, protection, monitoring, control, and performance reporting functions are discussed with examples given of current industry practice. The quantity and type of instrumentation used vary from operation to operation, but today many semi- autogenous circuits are highly instrumentated, and employ automatic process control for both circuit stabilization and optimization of economic performance. Examples of analog and digital based control systems exist, and are described.

Jan 1, 1982

By Robert M. Stevens, Arnoldo Acuña

INTRODUCTION In the early 1950s, underground miners and tunnel¬ing contractors were experimenting with ways to supple¬ment or eliminate track-bound loading and hauling equipment. Diesel-powered crawler and rubber-tire mounted front-end loaders and trucks designed for use on the surface were being modified and tried with limited but encouraging success. Miners began working with interested manufacturers to explore the develop¬ment of vehicles specifically designed to meet the de¬mands and constraints of underground material han¬dling. By the mid 1960s, load-haul-dump (LHD) vehicles were firmly established as a fundamental part of what has become known as the "trackless" mining concept, used in many mines and many countries around the world. The flexibility, mobility, and versatility of these units have given the industry a useful tool and have added new dimensions to mine development and produc¬tion. Many old mines have been redesigned to accom¬modate these trackless vehicles, and few new mining plans have failed to find some use for the concept during some phase of development and production. By 1977, several manufacturers in several different countries were producing a variety of LHD vehicles to meet the growing worldwide demand. GENERAL DESCRIPTION LHD vehicles combine certain characteristics of conventional front-end loaders and dump trucks, spe¬cifically designed for materials handling in underground mining and tunneling. The design intent is to provide one vehicle with one man, with the vehicle loading itself, hauling the load over level or inclined haulageways, and dumping the load. A typical production cycle of the most popular units has the operator driving the vehicle forward, forcing the bucket into the muck at or near floor level, and using the tractive effort of the vehicle and the prying action of the bucket to roll out and tilt back the load as shown in Fig. 1. With the bucket rolled back into the carrying position on the boom and the boom resting on the main frame of the vehicle, the load is hauled (trammed) to the dump point as shown in Fig. 2. At the dump point, the boom is raised, the bucket is rolled forward, and the load slides out as shown in Fig. 3. After dumping, the bucket is rolled back to the carrying position, the boom is returned to rest on the main frame, and the unit is driven back to the loading point for another load. There are two other types of LHD units that are slightly different in the cycles that they perform. One uses a hopper arrangement carried on the front of the machine, with a small bucket mounted ahead of the hopper. Several passes with the small bucket load the hopper, which is dumped by opening its floor. Al¬though this concept is several years old, it has gained less than 0.5% of the total market. The most recent LHD concept differs in that it has one bucket nesting inside another. The smaller inner bucket is loaded first, and it is then tilted back and above the larger bucket. When the larger bucket has been loaded, it is rolled back, and the total load is trammed to the dumping point. The dumping operation tilts the buckets in the reverse order from that of the loading operation. The impact of this new concept on the mining industry has not been measured yet. This chapter concentrates on the LHD vehicles employing the cycle described by Figs. 1 through 3, since these LHD units constitute an estimated 99% of the units in current use. MAIN VEHICLE FEATURES In general, the LHD vehicles available from most manufacturers share the same basic features.

Jan 1, 1982

By Terry A. Ring

Sand bed filters are used to remove large and small particles from liquid streams. The large particles are removed by the straining action of the filter bed and the small particles are removed by particle deposition on the surface of the bed particles. Particle deposition, while being essential for the filtering action of colloidal particles, is not the only process that occurs in the filter bed. Other processes that occur are (1) the substrate becomes filled with particles limiting further deposition, and (2) some deposited particles are resuspended. The sum total of all these processes determine the performance of a filter bed.

Jan 1, 1982

By Cheri Eby, William R. Eby

INTRODUCTION Pneumatic conveyance systems provide for material placement at high compaction rates in confined spaces. This method of conveyance provides proper roof support and ground stabilization important to underground mining activities. Today underground mining activities are conducted far differently than those of our ancestors, in that the reclamation process is the final step in any mining activity. Responsible mine owners are constantly seeking innovative methods to assist them in their reclamation procedures. During the last few years, particular attention has been paid to previously mined areas, as many of these abandoned areas lay open, imposing a constant threat to humans and animals. Considerable attention is being directed to applying proper methods for the filling and sealing of underground slopes, drifts, tunnels, and adits, because today we are experiencing the effects of past mining activities such as subsidence, acid mine water run-off, buring refuse piles, and underground mine fires. Furthermore humans and animals who have ventured into abandoned mine openings have died from exposure, suffocating gases, and mine collapse. This paper explains the method of pneumatically filling and sealing these openings and underground works by means of employing pneumatic equipment and proper backfill material together, thus achieving high material compaction and thereby providing the complete filling of the voids and alleviation of the mentioned dangers. NEUMATIC SYSTEMS The use of air to transport material is widely used; however, conveying abrasive material (e., rock, earth, and cement) requires certain pneumatic transport systems designed to handle the abrasiveness as well as the size of these materials. The Eby pneumatic transport sys tem, known as a Mobile Stower, in mounted on a 42-foot trailer pulled by a Kenwor th tractor. This arrangement allows for quick mobilization and project set-up. The pneumatic system, composed of several components assembled together, produces the volume and pressure of air required to transport the material. Knowledge of elevation, ambient temperature, and material composition at the locations to be backfilled play a big part in the design and useage of the pneumatic system. In this particular system design, material is placed by a front-end loader into an eight (8)-yard hopper which is located over a belt conveyor. The conveyor transports the material up to an air lock feeder, which is the metering devise used to feed the material into the Tee Injector located directly below. Air is supplied by a positive displacement blower which, in this instance, delivers up to 4400 CFM's of air at 8 to 12 PSI. Horse power requirements to drive the blower are met with the useage of either a diesel engine or an electric motor. A diesel engine enables the Mobile Stower to operate in remote areas. As the air flows through the upstream air piping, it passes through the Tee Injector and picks up the material and conveys it through the material conveyance pipe, (referred to as down-stream pipe), and out the placement nozzle. Depending upon material composition and the amount of tonnage to be moved, either mild carbon steel pipe or specially heat- treated hardened pipe is used for the material conveyance line. The entire pneumatic system is controlled from the operator's console. With the aid of instrumentation, only one person is required to operate the system. Tonnage rates vary in accordance with horse power and air supply, as well as

Jan 1, 1982

Although mining, particularly of gold and coal, played a significant role in the development of New Zealand, from the time of the spectacular gold rushes of the 1860s its economic importance to the country as a whole has decreased substantially since that time. Gold, coal and non-metallic agricultural and industrial minerals have been found in economically significant quantities, however, the search for base metals has not been successful.

Jan 1, 1982

By H. J. Winters

Position of the Porphyries in US Copper Supply The United States continues to be the largest producer and consumer of copper in the world. [Table 1] shows several production statistics for 1974, the most recent year that the non-communist world copper industry might consider a good year, and for 1976 and 1977. In 1974 an estimated 24% of the non-communist world's newly mined copper was mined in the US, and 87.89% of that was from the western porphyry coppers. In 1976 US new mine production was down to 22% of the non-communist world's newly mined copper, and the percentage of US new mine production supplied by the porphyry coppers had risen to 89-91%. In 1977 the statistics remained the same as in 1976. US porphyry copper production represented about 65% of US refined copper consumption in 1974, rose to 75% in 1976, and dropped back to 61% in 1977 as imports of foreign copper into the US began to swell. The financial situation of the porphyry copper mining industry continues to be very unhealthy. To see why; we can take a quick look at costs and prices.

Jan 1, 1982

By Antonio Marrano, Eda F. Quadros, Diogo Correa [Fo], Paulo T. Cruz

For many years the water pressure test has been used as a normal procedure to investigate the hydraulic characteristics of rock masses and discontinuities. Although the test has given evidence of problematic areas, the nature of flow and the so called equivalent permeability are seldom seriously affected by the testing tecnique. In order to improve the information on these points the Instituto de Pesquisas Tecnológicas de São Paulo - IPT, has developed an extensive program at laboratory and field research on the hydraulics at rock fractures. This paper summarizes the main items related to this research. Is shows that with only small improvements on field tests and some support of laboratory conductivity tests on natural rock joints it is possible to obtain a better understanding of the nature of flow in fractures, improve flow predictions and estimate the opening and hydraulic conductivity, as well as the transmissivity of natural joints or rock discontinuities.

Jan 1, 1982

By Jan M. Mutmansky, Y. J. Wang

Mine ventilation analysis is an engineering discipline that can be considered a branch of the body of science known as network analysis. Likewise, the group of engineering procedures known as the critical- path method (CPM) is considered a branch of network analysis. It is therefore not surprising that mine ventilation network analysis and CPM have many similarities. These similarities are useful in analyzing several types of mine ventilation problems and will be utilized in this paper. The analogy between the free split in a ventilation circuit and the critical path in a scheduling network has been recognized by Owili-Eger (1973). While this was recognized as a property of a general ventilation network, many important applications to controlled- splitting problems also exist. The mathematical procedures necessary to apply CPM and network methods have previously been presented (Wang, 1981; Wang, 1982). This paper will illustrate the implementation of these methods by application to mine ventilation networks.

Jan 1, 1982

By David A. Heitman

The Buick Concentrator is a highly automated operation which utilizes a process control system for continuous monitoring and control. The process control system development, installation, and application to the concentrator grinding and flotation circuits are presented in this paper. The design and implementation of analog field sensing instrumentation, a continuous on-stream X-ray analyzer, grinding and classfication circuit controls, and a recent digital process control system utilizing a centralized computer are discussed. Emphasis is placed on the project planning and installation of the digital control system including a presentation of future plans for continuing application of computer control.

Jan 1, 1982

By E. B. Jensen

The results of an extensive one- year test period of a nonelectric explosives detonating system led to the mine-wide adoption of this system at the Henderson Mine in early 1978. Since that time, extensive experience with nonelectric initiation has verified the earlier results which include the following benefits: 1. Increased blasting safety 2. Improved productivity 3. Cost effectiveness 4. High reliability At the present time, while electric blasting caps still experience a limited use restricted to trunkline initiation, all heading rounds as well as the longhole bell, undercut, boundary cutoff and raise blasting are detonated non-electrically. The primary blasting agent used is AN/FO, and primers are typically one of the following products (depending on application): PETN, semi-gelatin dynamites or a nonnitroglycerin water-gel slurry.

Jan 1, 1982

By J. W. Walkiewicz

One of the objectives of the Bureau of Mines is to develop substitution technology for scarce materials. In accordance with this goal, alloys containing lanthanum, cobalt, copper, and magnesium were investigated for fabrication of rare-earth-cobalt (RE-Co) permanent magnets. A complete substitution of lanthanum for samarium and a partial substitution of copper for cobalt was accomplished. Magnets of La-Co and La-Co-Cu-Mg alloys were fabricated by powder metallurgy techniques and evaluated. A maximum intrinsic coercivity of 23.2 kOe was obtained with a La-Co-Cu-Mg alloy. In comparison, maximum values of 9.3 kOe and 11.6 kOe were obtained with La-Co and La-Co-Cu alloys, respectively. The substitution of copper and magnesium for part of the cobalt resulted in a large increase of intrinsic coercivity, similar to the results of Bureau research with mischmetal-Co-Cu-Mg alloys. Unlike the mischmetal-Co-Cu-Mg magnets, the La-Co-Cu-Mg magnets showed signs of physical deterioration on exposure to air. The effects of fabrication parameters on the magnetic properties of the La-Co-Cu-Mg alloys were also determined.

Jan 1, 1982

By J. L. Taylor, E. B. Viljoen, W. M. Craig, A. M. McIntosh

The Chemwes uranium plant treats old gold-plant residues from the Sttifontein and Buffelsfontein Gold Mines by acid leaching, belt filtration, countercurrent ion exchange (ClX), and Bufflex solvent extraction (SX). The uranium is recovered by precipitation as ammonium diuranate. Absorption and elution in the CIX section are achieved in four NIMCIX columns operating as two parallel streams. Each loading column is 4,85 m in diameter and contains 12 absorption stages. The elution columns are 3 m in diameter and contain 8 stages. The eluant used is 10 per cent sulphuric acid at ambient temperature. During the commissioning and initial operating periods reported here, the plant yielded an average barren solution of 1,6 p.p.m. of U3O8 from a feed with a mean U3O8 concentration of 132 p.p.m. The U3O8 concentrations in the barren solution were better than 2 p.p.m. some 85 per cent of the time, and better than I p.p.m.73 per cent of the time. Investigations are underway to institute an automatic control system that will result in the U3O8 values on the resin and in the barren solution being maintained at or near the target values in spite of changes in the concentration of uranium in the feed solution.

Jan 1, 1982