Search Documents

By Robert L. Sundeen, Richard V. Wenberg

INTRODUCTION Early rock-bolting practice usually consisted of ran¬domly installing bolts, using hand-held drilling equip¬ment such as air-leg mounted sinkers or stopers. As bolting technology evolved, the practice of installing uniform bolt patterns was developed, utilizing random bolt installation as required within the uniform pattern. The uniform rock-bolting technique, when used as the principal method of rock support, requires drills and jumbos designed specifically for rock bolting. This equipment is similar to conventional face drilling machines, except that the jumbos can orient the drills to obtain any necessary bolting angle; often, this means bolts may be installed at or near perpendicular to the centerline of the drift or stope opening. Fig. I shows a typical rubber-tired rock-bolting jumbo of the type commonly used in drifts and room-and-pillar mining. Modern rock-bolting jumbos are capable of drilling the required holes, inserting rockbolts, and torquing them to proper levels. Jumbos also are available for use with resin-anchored bolts. Probably the most unusual of this type utilizes a rotating bolt turret that carries the rock drill, resin charging unit, and the bolt in a single mechanism. Once the turret is loaded with the resin and bolt, further manual effort is not re¬quired. Drilling and bolt placement are accomplished by the operator from a station remote from the bolt site. Fig. 2 shows this turret device. Roof-bolting jumbos are available mounted on rail, crawler, or rubber-tired chassis. Various types of rock drills are used. Depending upon the type of rock, these may include rotary, percussion, or rotary-percussion drills. Fig. 3 shows a typical rail-mounted jumbo. CONDITIONS INFLUENCING APPLICATION General Rock Conditions Rock-bolting generally is applicable in moderately hard to hard rock. No particular type of rock is ex-

Jan 1, 1982

No noticeable international economic recovery occurred during the first half of 1982. Industrial production continued to fall in the United States, Canada and Italy and to hold steady in France. Modest increases in production occurred in Japan, England and Germany, although some decline took place from March to April. The U.S. mining industry has been more severely affected by the world recession than the U.S. economy. This is not immediately obvious when comparing the U.S. mining industrial production index from 1981 to 1982, which decreased 8.5 percent, as compared to a 7.1 percent decline for total domestic industries. However, "mining" industry statistics in the U.S. national economic accounting system include petroleum and natural gas as well as minerals. When metal mining is isolated, the decrease in production from 1981 to 1982 is 19.3 percent. If metal mining production continues to perform at the same rate during the third and fourth quarters of 1982 as during the first half of the year, declines from 1981 levels will be quite severe. Aluminum will have declined 22 percent, copper 18 percent, iron ore 24 percent, lead 3 percent, steel 29 percent, titanium 2 percent and zinc 25 percent.

Jan 1, 1982

By Richard H. Bares

The general or macroclimate of the study sites in western North Dakota is characterized by rapid and sometimes extreme daily and day-to-day temperature fluctuations, rainfall patterns which are erratic in spatial and temporal distribution and intensity, generally low relative humidity, plentiful sunshine, nearly continuous air movement, and a relatively short frost-free period. Of particular relevance to plant growth and productivity is the mosaic of microclimates: these microclimates are affected by landform (convex and concave surfaces); exposure; slope angle, length and aspect; soil color, texture and surface cover (litter), and vegetation cover. The most critical plant growth governing factor in this region is available water. It is determined principally by water input (precipitation) and water loss (evapotranspiration) which is increased by high temperatures, wind, and poor litter and vegetation cover. While spring and fall precipitation is generally gentle and soil-soaking summer rains frequently come in the form of intensive, soil-washing, localized convective thunderstorms of short duration. Due to the convective nature of these storms, summer rainfall is particularly affected by regional topography; southwest slopes and crests often receive more rainfall since these storms usually move in a northeasterly direction. The water loss due to runoff and consequent soil erosion arc major problems resulting from such "cloudbursts". Previous fall precipitation (September - October) when added to current seasonal precipitation (March - August) was found to be significantly correlated (r-.93) with plant production. Winter precipitation (snowfall) is relatively light as the prevailing weather is dominated by dry polar air masses from the north. The nearly continuous wind is responsible for removing snow from open exposures and depositing it in depressions and windbreaks. Although the winter precipitation is not a large component of the total annual precipitation, conservation of that which does occur would contribute to plant production during the following growing season. Generally clear skies over the region facilitate receipt of abundant sunshine at the earth's surface. While good for early season soil warming and plant photosynthesis, this abundant sunshine coupled with long days and nearly continuous wind is responsible for evapotranspiration exceeding precipitation by an average of six inches between June' and September. On a local (micro) scale, the water deficit is most severe on the southern exposures which receive the most direct (most effective) solar radiation and therefore are warmer than other exposures. On a broader scale, it was found that ambient temperature extremes were slightly but significantly greater in the town of Beulah in the Knife River Valley than at the upland test sites, This may have been due to the difference in topography and/or the "urban heat island" effect. It is known that air temperatures in large cities may be 2° to 4°C higher than that of the surrounding countryside. It is also well known that basins, depressions or valleys are sinks for cold air masses and are often subject to frosts not occurring on adjacent upland sites.

Jan 1, 1982

By William Petruk

The development of automatic image analysers brought the application of image analysis into process mineralogy because the analysers can measure parameters more easily, quickly and accurately than by manual grain counting techniques, and can also collect data unobtainable by manual grain counting. Data from ore specimens and mill products are used to predict and to define the behaviour of minerals during processing. The analyses are generally performed on the basis of either surface areas or linear intercepts of grains in polished or thin sections, and the data are computer processed to give mineral quantities, liberations, size distributions, and characteristics of middling particles. For analysis, the minerals must be detectable and discriminatable from each other. An image editor is usually used when minerals are not easily discriminated. In addition BSE-8EM photographs have been used where the silicate minerals could not be discriminated from the mounting media. Methods of analysis, typical results, and their applications are discussed.

Jan 1, 1982

By Charles J. Hass

INTRODUCTION Deformation measurements are some of the simplest and most useful measurements that can be made by the mining/rock mechanics engineer in assessing the sta¬bility of openings in rock. A number of tools and tech¬niques are presently available. This chapter will de¬scribe the most common instruments, their application, and present the equations needed for data reduction. MECHANICAL STRAIN GAGE Description of Instrument A mechanical strain gage of the Whittemore type shown in Fig. I is a useful instrument for measuring deformations of pillars, sidewalls, and roofs of under¬ground mines. Measurement gage lengths typically range from 51 to 254 mm (2 to 10 in.), and the dial indicator reads to 0.0025 mm (0.0001 in.). The instru¬ment measures the deformation between precision gage points which are anchored in the rock. The anchor points are typically grouted in small holes drilled 12.5 mm (1/2 in.) or so deep into the rock. Strain a is calculated from the measured deformation AL with the equation [ ] where L is gage length. A necessary accessory for the instrument is a master bar normally made from invar steel having a low co¬efficient of thermal expansion. This bar allows one to check the instrument for changes in the mechanical zero point and to correct for temperature effects on the measuring instrument. The instrument is available from Soiltest, Inc. for a cost of approximately $340; the cost of the master bar is approximately $55; and nonreusable brass inserts which are anchored in the rock are nominally priced at $0.27 each. All prices are for 1978. Applications Two classes of applications may be considered, one where only one measurement direction is involved and the second where three measurement directions are em¬ployed. Applications where only one measurement di¬rection is necessary include: monitoring crack or frac¬ture separation or shear movement with anchor points on opposite sides of the discontinuity; measurement of vertical strain in a pillar or sidewall; and measurement of steel support deformations with anchors in the steel members. The more general application involves a strain ro¬sette consisting of three measurement directions which for convenience are oriented 1.04 rad (60°) apart to form an equilateral triangle as shown in Fig. 2. Strains in the three measurement directions [ ]

Jan 1, 1982

By William F. Eichfeld, Robert J. Wenzel

INTRODUCTION The phrase "subsidence control planning" can refer to the use of specific mining methods and-specialized techniques to control subsidence events or it can refer to planning for subsidence by predicting its magnitude and timing and further planning mitigation strategies. In the first case the objective is actually subsidence prevention while in the second it is a design procedure that seeks to maximize the use of both surface and subsurface resources. Neither technology is well developed at this point. The purpose of this presentation is to briefly outline the Department of Energy's Subsidence Program. This program is, in general, bases on the premise that subsidence control technology, by any definition, can be accomplished only through a thorough and rigorous understanding of subsidence phenomena. This understanding must come from many well planned and executed studies of stress redistribution and strata deformation as they occur during mining activities. There is presently considerable incentive to improve our subsidence engineering capabilities due to the desire for increased coal utilization with acceptable environmental impact. Considerable research in this area is being sponsored by federal and state governmental agencies, universities, and the coal industry. Federal sponsorship has been borne by the Department of Energy, the Bureau of Mines, the Office of Surface Mining and the U.S. Geological Survey for the most part. These agencies have carried out basic research in their laboratories and have contracted with other organizations for additional work. At this time most of the available resources are directed toward contract research, especially in DOE. It is the DOE research plan which will be addressed here.

Jan 1, 1982

By D. Y. Geng, Syd S. Peng

This paper analyzes the effects of geology and mining methods on surface subsidence factor, angle of draw and angle of critical deformation based on the results of 40 longwall subsidence profiles in the Northern Appalachian coalfield. Several equations were derived to show the relationships between those parameters. Furthermore, the equations were transferred and plotted in the form of several monographs for convenience of applications.

Jan 1, 1982

By Terry G. Richard, Vernal H. Kenner, Sunder H. Advani

This paper presents and discusses the results of thirty-one fracture toughness tests on Pennsylvanian Age Clay Shale. Two different orientations for this anisotropic material were studied and two series of tests were conducted, namely, 1. a test series to determine the effect of moisture content on fracture toughness, and 2. a test series to study mixed mode fracture. Increased absorbed moisture is found to reduce fracture toughness. Several analyses of mixed mode failure are found to give varying non-conservative predictions of failure stress intensity level.

Jan 1, 1982

By K. N. Clark, N. B. Carter, C. G. Thomas, V 7. 0 / 300 dpi

A statistically designed, experimental study showed how gangue minerals, flux additions, fineness of grind, firing temperature, and time affect the properties of acid pellets made from a Western Australian hematite ore. Alumina has less effect than silica and lime, but interactions between the six variables occur, which influence abrasion index, reducibility, and cold compression strength. Finer grinding has little influence on reducibility but improves the other two properties. The major variable is firing temperature, which interacts with all other variables to affect pellet properties. Calculations based on the data show the implications for straight-grate pellet plants and optimum hood temperature ranges.

Jan 1, 1982

By Thomas R. Smith

This paper covers oil shale resources in those countries that border the Pacific Rim. The major known resources around the Pacific Rim occur in the Western United States, Australia, the People's Republic of China, (PRC) and the Thailand/Burma region. The location of these deposits is shown in Figure 1. In 1965, the U.S. Geological Survey estimated world oil shale deposits of over 4 quadrillion tons having a potential oil yield of over 2 quadrillion barrels. If all this were extracted, it could meet the world's entire energy needs far into the future. However, the Survey also estimated the spent shale waste could cover all of the surface of the world to a depth of about 10 feet. Thus, for this and many other technical and economic reasons, it does not appear to be feasible to develop a large portion of the world's oil shale resources in this century; nor will shale in itself solve our energy problems. Nevertheless, shale oil and other ' synthetic fuels are expected to play an important role in new energy supplies in the longer term. WHAT IS OIL SHALE OR SHALE OIL? The term "oil shale" is sometimes a misnomer, in that the rock is often more of a limestone or siltstone than a shale. The common link between resources termed “oil shale" is that they all contain an insoluble substance cal led kerogen (which is from the Greek words for waxmaking). Kerogen is a form of organic carbon derived from a variety of plants ranging from algae to higher plants. When heated sufficiently, the kerogen generates hydrocarbons called shale oil, a form of synthetic crude oil that in most cases is lower in hydrogen content than conventional crude oil. The amount of oil in oil shale is relatively small --roughly 10 percent (by weight) in the richer shales. To upgrade this synthetic oil to usable products, additional processing is necessary. This brief sketch gives an idea of what this different, but significant, form of hydrocarbon is like. ENVIRONMENTS OF DEPOSITION Most oil shale deposits fall into three environments of sediment deposition: 1ake (called lacustrine), sea (marine) and river (fluvial-deltaic). In each case, the deposition of oil shales took place in quiet water environments where plant life, particularly algal plants, could flourish and, after dying, be deposited in unoxygenated water where the kerogen precursors would be safe from destruction by oxidation. The oil shales that were deposited in large lake basins (lacustrine) have attracted the most attention for development over the years. They often have multiple seams, deposited in a cyclic nature with extensive areal distribution and rapid vertical changes in kerogen content. Grades are moderate to high, ranging from 80 to 200 liters per tonne. Rundle in Australia and the Piceance Creek Basin in Colorado are examples of this type. Both deposits represent large volumes of oil shale in small areas which could provide the large volume of feedstock needed for future commercial operations. The stratigraphic sections of these two deposits feature thick oil shale seams with average grades of 80 - 125 liters/tonne conducive to both open pit, and underground operations. However, the rock strength of the Rundle shale is not sufficient to - support underground mining. On the other hand, the Colorado deposits, being more carbonate in nature, are sufficiently strong to support either type of mining depending on the overburden to ore ratio. These latter types of deposits will likely provide the first target for development of a commercial industry. The marine type is characterized by extensive areal distribution with relatively thin seams. The grades are generally low to moderate, ranging from 50 to 120 liters per tonne. The marine oil shales are common worldwide, and their attractiveness for mining is dependent on the overburden to ore ratio. Because of their widespread areal distribution, their in situ resources can be quite large. The Toolebuc Formation in Central , Queensland, Australia is a good example of this type of deposit being 7-10 meters thick over an extensive area. The Julia Creek deposit with its favorable overburden-to-ore ratio is being studied for possible development. In a fluvial-deltaic environment, there are many small lakes or bogs associated with rivers in which a very pure type of oil shale called torbanite could form. Torbanites are very high grade containing up to 75 percent hydrocarbons. The known occurrences are generally small lenticular deposits associated with coal seams. Even with the high grades, it is not likely that any of the known deposits would warrant commercial development because of their small size. The torbanite deposits in New South Wales, Australia were processed prior to World War I1 near the town of Glen Davis. However, today's known resources of this type are not large enough to warrant a commercial plant.

Jan 1, 1982

By R. M. Giegerich

"This paper begins with a brief history of Madawaska Mines, a brief description of the geology, mining methods and equipment, and the historical development of 7/8-in. tapered drilling equipment. It then outlines the performance characteristics and inherent problems of the traditional 12-degree, tapered connection, blade-type insert bits. Service-free (Unipass) button-type insert bits are presented as a possible solution to these problems. The paper concludes with an analysis of button bit performance to date.Brief History of Madawaska MinesMadawaska Mines Limited, near Bancroft, Ontario, is in Faraday Township, Hastings County, approximately 100 miles northeast of Toronto and 100 miles west of Ottawa.The mine re-opened in 1976committed to 1,500 tons per day to provide approximately 600,000 pounds of yellowcake (U3O8) per year to A.G.I.P. (an Italian government agency) under the joint ownership of Federal Resources Corporation, Salt Lake City (51%), and Consolidated Canadian Faraday Limited (49%). At present, the mine is producing approximately 2 pounds per ton (.1% U3O8) at the rate of 60,000 pounds per month. The mine employs about 400 employees.Brief Description of Geology, Mining Methods and EquipmentGeologyThe Grenville metasediments of the mine area are chiefly paragneiss, amphobolite and some carbonate (marble) rocks, which were intruded by a basic rock, altered to a metagabbrometadiorite. These formations are generally concordant, striking east to northeast and dipping 45 to 60 degrees to the south. Locally, the metagabbro is often discordant. The above group of rocks (mixed hybrid gneisses) forms the hanging wall of the south-dipping Faraday granite sheet and was intruded by nepheline syenite, syenite and granite. The ore occurs in the granite-syenite-pegmatite dykes that are probably genetically related to the Faraday granite. The ore shoots are erratically distributed within the pegmatite bodies, mainly on the hanging or footwalls but also medially. Their size varies from 50 to 350 feet in length, 5 to 40 feet in width and 50 to 200 feet in height. The ore occurs most frequently in a medium-grained granite or syenite, well hematized with 10 to 30% mafic crystals of pyroxene, amphibole and/or relics of the host rock."

Jan 1, 1982

By Thomas R. Stauffer

The principle that conventional schemes for taxing petroleum or mineral resources are "inefficient" is illustrated using simulation calculations tested against an "ideal" system. Inefficiency is defined as the relative success in maximizing expected government revenues from the resources. Most systems fail because: 1) they leave oil in limbo, i.e. unproduced because of excessive fiscal burden; or 2) they unnecessarily increase the variance in the explorationist'c, rate of return by undertaxing large fields and overtaxing smaller but infra-marginal fields. This increases his discount rate and reduces taxable surplus. An "ideal" tax system is specified which maximizes government revenues while minimizing risk to the operator. Two criteria are developed: 1) the tax falls to zero on fields which yield only the minimum necessary rate of return ("marginal" fields); and 2) the after-tax present value of all fields is the same for all fields above a threshhold size. In particular, marginal fields, while contrib- uting little to expected values, do contribute to reducing variance and hence risk praemia by distributing the exploration costs over a higher probability of successful outcomes.

Jan 1, 1982

By M. S. Cetiner

This report describes the prototype development If a medium to high voltage coupler, suitable for underground coal mining operations. The coupler has such unique features as automatic dust covers and continuous phase pin shielding. The coupler is rated at 7500V and 250A continuous operation.

Jan 1, 1982

By B. H. G. Brady, C. M. St. John

Computational schemes for analysis of rock mass response to excavation, loading and other imposed changes, are employed pervasively in rock mechanics practice. Applications range in complexity from determination of stress and displacement distributions around openings, to prediction of the thermo-hydromechanical behaviour of a saturated fissured mass. While this may be taken as apparent sophistication in rock mechanics design activity, the indiscriminate use of computer methods may sometimes conceal inferior and inadequate engineering procedures. These inadequacies may not always be recognized, due to the general uncertainties which are inherent in rock mechanics investigations. This paper seeks to identify some common deficiencies in rock mechanics applications of computational schemes, and to propose ways of eliminating them. It also indicates some specific developments and applications of computational procedures, which are required to address persistent design problems in geomechanics practice.

Jan 1, 1982

By Claudio Gutierrez

It has been claimed (Eadington and Rosser, 1969) that when freshly precipitated lead sulfide is in contact with oxygen-containing water, there is an "induction period" of at least a few hours during which no detectable oxidation of the lead sulfide takes place This effect would be of the utmost importance for the adsorption of xanthate on galena in flotation mills. It was tried here to reproduce the results obtained in (Eadington and Rosser, 1969), but no "induction period" was found. Besides, reasons are given to prove that the oxidation mechanism proposed by Eadington and Prosser (1969) is not realistic.

Jan 1, 1982

By Paul T. Allsman

The guiding principle in developing this plan resulted from evaluating potential future markets for oil, the quantity of mineable oil shale and the optimum rate of production comensurate with market demand on the available oil from shale. In addition, the rate of production may depend upon a solution to the problems of scarcity of resources other than oil shale. The rate of production finally will tend to establish the choice of technologies with these limits. The principle components discussed will be: 1) The place of oil shale among the various energy sources and its relative adaptability for use in the area of major consumptive demand. 2) A recalculation of the reserves and their classification on the basis of quantity, grade - gallons per ton, - and physical characteristics principally thickness, overburden and depth.

Jan 1, 1982

By S. S. Peng

In dealing with the mining engineering problems, the traditional approaches of laboratory experimental simulations and/or analytical solutions are not very effective. Mainly because the field problems are too complex to be solved with a few simplified assumptions. Conversely it is also true that the experimental and analytical/ numerical models currently available are far from being able to model the actual cases. Under such conditions, the most effective mean of research into mining engineering problems is to combine the mine (field) investigations with laboratory and / or analytical modelings. It is with this concept in mind this research was initiated in 1973. 'The field investigations which began in the fall of 1978 consisted of mainly visiting the mines where surface subsidence monitorings had been or were being monitored and/or surface structural changes had occurred. From such visits, subsidence data were collected. A quick analysis of those data provided preliminary understandings of the characteristics of the surface subsidence parameters in the regions (1-5). Using those date, models of various types are being developed for subsidence prediction / control. So far, a total of 44 longwall subsidence profiles in 22 longwall panels and 10 room-and-pillar profiles in 5 room and-pillar sections have been collected. This paper summarizes the combined results published previously (1-5) and present the preliminary results of the predictive models developed.

Jan 1, 1982

By J. S. Dunning

The Bureau of Mines investigated a series of Fe-Al-Mo alloys strengthened by ZrC (zirconium carbide) precipitates as chromium-free substitutes for stainless steels. Melting and fabrication methods were devised, and the effects of minor additions of columbium (niobium) and cerium on the mechanical properties and oxidation resistance were determined. Zirconium carbides could not be con-trolled reliably to produce fine precipitate dispersions. A more reliable carbide strengthening mechanism is required if the high-temperature strengths of types 304 and 316 stainless steels are to be duplicated. Workability and oxidation resistance of the alloy series were excellent.

Jan 1, 1982

By J. van Oldenborgh

The world market for bunkers represents some 140 MT (1980) of marine fuel oil and distillates. This is equivalent to 23CMT of coal, a potential market for steam coal larger than the total seaborne trade of steam and metallurgical coal today, and an obvious area which could contribute savings in world oil consumption. Oil bunkers are lifted fairly evenly throughout the world, the main supplying regions being Western Europe, the Middle East, North and Central America and Japan (Figure 1). Not surprisingly, the main customers are the tankers representing about 50 percent of the world market - (95 percent of the Middle East Market) - dry bulkers represent some 30 percent and general cargo ships the rest.

Jan 1, 1982

By G. Thom, A. Kay, J. B. Hyde

"This paper will initially outline the specific types of copper castings used in blast furnace iron production. Tuyeres, tuyere coolers and stack cooling plates will be discussed in some depth, with particular reference to their dimensional configuration and purpose.Following this, the failure of such cooling members will be discussed, with special focus on tuyeres. Tuyeres are the most common casting which often requires replacement. Reasons for failure and its effect on operations will also be included.The latter sections of the paper will deal with the strict specifications demanded by ironmakers regarding copper castings. The justification for such rigid demands will be explained through the material presented earlier in the paper.IntroductionThe modern 5000-tpd blast furnace, worth millions, is a large capital investment to be sitting idle. Consequently, ironmakers strive to minimize the loss in iron production and revenue from furnace downtime. Two major causes of downtime are furnace relines and shutdowns to replace damaged tuyeresor tuyere coolers. Copper ancillaries are important items in the production of iron. They are consumable items, therefore they contribute to the campaign life or to the downtime in blast furnace production.Several combinations of lining and cooling systems have been used with varying degrees of success. Blast furnace refractories have evolved from ceramic to carbonaceous linings. The Russians and Japanese have successfully introduced stave-cooled furnaces that may have several forms, such as evaporative cooling. Stelco has two furnaces which use the Russian-designed cast iron system. However, this paper will be confined to the use of copper cast cooling members in a conventional internally cooled furnace.Figure 1 is a schematic cross section of the E blast furnace. The three major sections of a blast furnace-the stack, bosh and hearth-are identified. Further, the locations of the various copper members are indicated. This furnace produces an average of 5300 tons of hot metal per day."

Jan 1, 1982