Search Documents

By A. Smith

After the introduction of mechanized bord-and-pillar development at Dumacol in 1958, pillars were being developed at a much faster rate than they could be extracted by hand loading methods. Efforts were therefore made to increase the rate of pillar extraction by mechanization. Following two partially successful mechanized stooping trials in 1964 and 1971, it was decided that mechanized pillar extraction with 1 m3 cable-reel front-end loaders should be introduced. The first section to employ the new equipment started production in May 1979, and the mine now has four mechanized pillarextraction sections in operation. Considerable improvements in production, productivity, safety, and percentage extraction have been achieved.

Jan 1, 1985

By Bruce H. Gardner, Stephen A. Miller, Shosei Serata

The Bryan Mound salt dome in Freeport, Texas, has some of the largest and oldest solution caverns in the U.S. There are a total of five caverns of varying shapes and sizes randomly distributed throughout the salt dome. When the caverns were converted from a brine production to an oil storage operation, the effects on long-term stability of the caverns and inter-cavern behavior were analyzed to evaluate the future safety of the storage operation. The analysis was based on a worst-possible-case scenario, including accidental wellhead pressure loss. The impact of this pressure loss upon the thinnest partition between the two closest caverns was analyzed, using a case example of storing lightest weight LPG, thereby creating maximum differential pressures between these two caverns. The finite element method with the REM computer code was utilized for this analysis. Results of the analysis illustrate the basic mechanisms of the long-term behavior of the multiple caverns in the LPG storage operation.

Jan 1, 1985

By Ahmad Saberian

Five salt samples 20 to 40 cm tall, sealed on all sides except one, were exposed to a series of dissolution tests in various brine solutions and at different temperatures. Solvents were in the 50 to 96% saturation range and the temperatures varied between 40°F and 150°F. The collected dissolution data sets for vertical salt surfaces were analyzed and three were selected to be used for developing a general relation. After various curve fitting efforts, an empirical relation for salt dissolution rate as a function of brine temperature and salinity was developed.

Jan 1, 1985

Most of the gold reef mined today in South Africa is approximately 1 m in width with slopes about 30 m long. To prevent production interruptions it is essential that the stopes should not be blasted in sections. The shortage of experienced labour and arduous working conditions at the face dictate the need for simple blasting techniques.Hence, a pyrotechnic blasting system of sequential firing is in use at present, although research work to improve this technique is in progress.

Jan 1, 1985

By Dennis J. McCarthy

TAX TREATMENT OF EXPLORATION AND DEVELOPMENT EXPENSES Exploration Expenditures General Principles. Exploration expenditures are expenses incurred within the United States or the Outer Continental Shelf for the purpose of ascertaining the existence, location, extent or quality of any deposit of ore or other mineral. Section 617 of the Internal Revenue Code permits a taxpayer to elect to deduct these expenditures currently. In default of election, exploration expenditures must be capitalized and included in the basis of the mineral property for purposes of determining cost depletion. Entitlement to Deduction. In order to qualify for current deduction, exploration expenditures must be incurred prior to the commencement of the development stage, i.e., when mineral deposits are shown to exist in sufficient quantity and quality to reasonably justify commercial exploitation. Generally, expenditures for geological and geophysical investigations, reconnaissance, surveying, testpitting, trenching, drilling, driving of exploration tunnels and adits and similar types of work constitute exploration expenditures if incurred prior to the commencement of development. However, expenditures to further delineate the extent and location of an existing commercially marketable deposit are not exploration expenditures. Exploration expenditures may be incurred from within a producing mine to ascertain the existence of what appears to be a different ore deposit. Expenditures for property which is subject to an allowance for depreciation are not deductible under §617. However, depreciation properly allowable on assets used in exploration is an exploration expenditure. Election to Deduct Exploration Expenditures. The election to deduct exploration expenditures is made by deducting these expenditures in the return for the first taxable year for which such treatment is desired. The election applies to all properties of the taxpayer. Once the election is made all exploration expenditures, in the year of election and thereafter, must be deducted, unless the election is revoked with the prior consent of the Commissioner. The Tax Equity and Fiscal Responsibility Act of 1982 (TEFRA) made substantial changes in the treatment of exploration expenditures. For exploration expenses incurred after 1982 and before 1984 by a corporation, the amount currently deductible is limited to 85% of the expenditure. The remaining 15% must be capitalized and recovered over a five-year period. Although exploration costs capitalized under this provision are not part of the basis of the property for cost depletion purposes, investment credit may be claimed with respect to these expenditures. Further changes have been added by the Tax Reform Act of 1984 with respect to expenditures made after 1984. The Act reduces the amount of otherwise currently deductible costs from 85% to 80%. Additionally, it limits the availability of the investment credit for capitalized mineral exploration costs to deposits located in the United States. TEFRA also allows individuals a special method of recovery under which exploration expenditures may, at the election of the taxpayer, be amortized ratably over a 10-year period beginning with the year in which the costs are paid or incurred. If taxpayer does not use this method, the excess of the exploration expenditures actually deducted over the amount that would have been deducted if 10 year amortization had been elected is an item of tax preference subject to the alternative minimum tax.

Jan 1, 1985

By David C. Oyler, Paul B. Stubbs

The Bureau of Mines and United States Steel Corp. are conducting a joint project to monitor formation pressures at a large (23-well) coal- bed gas drainage field near Oak Grove, AL. Three monitor holes were drilled in late 1981, and pressure monitoring began in December 1981. The Bureau of Mines direct method was used to obtain gas content data from cores taken in the monitor holes. Comparison of the 1981 gas con- tent data from the monitor holes with initial gas content values obtain- ed from the production wells in 1977 indicates a 50-pct reduction in ad- sorbed gas content inside the pattern and a 29-pct reduction at one point 500 ft outside the pattern. The combination of pressure and gas content data has also allowed an in situ isotherm curve, relating the formation pressure to adsorbed gas content, to be developed for the area of the production wells. From the current rate of pressure decline (1 lbf/inz per month), the observed changes in gas content, and the isotherm curve, it appears that most of the early gas production came from within the pattern, but since 1981 (and possibly earlier) most of the gas produced has been migrating to the wells from outside the pattern area.

Jan 1, 1985

By J. C. Agarwal

Major scientific discoveries cannot be programmed. New or frontier technology, however, can and should be planned. It is the vital force underlying the business strategy of a vigorous and profitable mining and metals company. Generally, a radical departure from existing technology is required to 1) Enhance the competitive value of ore reserves, i.e., to turn low grade or marginal reserves into competitive reserves. 2) To increase yield and decrease costs. 3) To decrease investment. 4) To increase mine life. 5) To improve product quality to meet market demands. The very definition of frontier technology implies that it is so different that the old plant, if already in use, will not be directly suitable to use the new technology. Therefore, a priori, we know that the commercialization of frontier technology would very likely involve new investment. The recommended technique of economic and technical analyses, I propose to call "Success Analysis.'' Simply stated, it forces us, by step- by-step procedure, to ask "what is needed to succeed in this particular project." Therefore, the first step is to identify what is meant by "success." The definition of "success" requires an agreement with top management or sponsors of the project as to what constitutes "success" in their minds as contrast to the technical people perception of "success." In general, top management would define success as meeting: 1) The technical objectives, i.e., technology being developed would produce the desired product at the acceptable quality. 2) Financial objectives, i.e., when commercialized, the project's capital cost, operating costs and return on investment are better than the projects they would normally fund. The return has to be better because new technology is inherently riskier. 3) Marketing objectives in that the project will produce product of acceptable quality in timely manner, i.e., scale-up to commercial plant would not cause undue delays in start-up and that large fix-up expenditure would not be required to protect the projected return on the investment. Many projects are started in the laboratory to develop "Frontier Technology" in mineral processing. Most of these efforts are never commercialized. There are many causes of these failures. The major causes are listed below: 1) Inadequate communication with the sponsors of the project so that project objectives are defined and agreed to by all. 2) Ill-defined technical problems. 3) Incomplete development of technology. This has two major components: a. Incorrect scale-up and engineering. b. Inadequate start-up and maintenance planning. 4) Incomplete and over-optimistic process economics. 5) Lack of understanding of the future behavior of the marketplace. 6) Failure to complete R&D effort by the time it is needed. 7) Incorrect projections of human resources required; that is, technical, managerial and operating. 8) Lack of realistic forecast of the expenditures required for commercialization of the R&D effort. These pitfalls can be avoided by comprehensive planning and the use of success analysis technique. The major elements in "Success Analysis" are: 1) Identification of the "need" for new technology. 2) Unbiased and complete scale-up engineering. 3) Acceptable economic feasibility with enough margin of error in the sale prices and operating costs to justify the inherent risks in frontier technology. 4) Timing for availability of investment capital and markets. Many failures in the development of frontier technology are preordained because the initial selection of the research project has been without adequate attention to the needs of the industry. Many very innovative hydrometallurgical processes for recovery of copper from concentrates were developed in the past twenty years. They have not adapted except to a very minor extent because they did not satisfy the success analysis criteria. The copper industry in North America needed a process to compete against high grade ores and to avoid

Jan 1, 1985

By C. M. K. Boldt

The Bureau of Mines studied the compaction characteristics of metal and nonmetal tailings. Densities of the tailings and zone of compaction influence, compactive effort, and cost of equipment are related to changes in the factor of safety for specific grain-sized tailings and embankment configurations. Field testing was accomplished in two distinct phases. The first phase investigated the effectiveness of using a nuclear gauge on metal and nonmetal tailings to produce rapid, instantaneous measurements of moisture content, wet density, and dry density. The results of the nuclear gauge testing are presented in chapter 1. Chapter 2 presents a comparison of the compactive effectiveness of three different pieces of construction equipment on a coarse-grained metal tailings pond. The three pieces of equipment chosen for study were a DBH track-mounted dozer, a DSOO rubber-tired dozer, and a SP848 vibratory smooth-drum compactor.

Jan 1, 1985

By Andrew B. Cecala

As deeper seams are continually mined, methane liberation will continue to increase and must be monitored effectively. To effectively monitor and develop appropriate control technology, methane-liberation patterns must be known. The Bureau of Mines recently completed a study to identify specific patterns of face methane liberation during long- wall mining. Both of the longwall faces surveyed had high methane liberation rates. At one longwall face, most of the methane was liberated during cutting of coal by the shearer mining machine. At the second face, a significant portion of methane was emitted from the face and floor. An effective methane-monitoring system would be different for each longwall panel because of the differences in how the gas is released along the face.

Jan 1, 1985

By R. R. Unterberger

Three different physical techniques have been used to see through or probe into rocks, so miners might know what is ahead or overhead. These are radar, sonar, and a unique type of sonar called nonlinear sonar. Five radar systems have been developed. The highest frequency used is 4300 MHz for detecting small fractures at close range. This gives the best resolution. For longest range (over 2000 m, or 6560 ft) we use the 30 MHz radar for finding faults ahead of mining or ranging to salt dome flanks. Two types of salt, dome and bedded, are recognized. Radar works well in dry (dome) salt, but not in bedded salt which contains small amounts of water. The dipole moment of water absorbs energy from the radar. Thus was born the 30 MHz radar system and sonar probing systems. These can probe to 100 m (328 ft) even into wet salt. All probing systems measure data in time, which are converted to distance by measuring the time of travel of radar or sonar through salt pillars of known thickness. Ranges of probing in salt are from less than 1 m (3.3 ft) to more than 2000 m (6560 ft). Uses of radar and sonar probing in mines include mapping the top of salt above a mine; mapping salt dome flanks; finding impurities in salt such as anhydrite, sandstone, or potash stringers; locating old boreholes in salt pillars; locating fractures in salt; and finding faults or water zones ahead of mining.

Jan 1, 1985

By P. R. A. Andrews

"A sample of flotation feed from Bakertalc Inc., High water, Quebec was subjected to flotation evaluation to improve the recovery of talc. A number of alternative frother/collectors and depressants as well as flotation parameters including pH, conditioning time, frother/collector concentration and pulp density were assessed. In addition, the possibility of using a size coarser than that currently employed for flotation (95% minus 50 um) was investigated.As far as possible, a laboratory duplication of the present circuit arrangement was folio wed so as to minimize the cost of any changes. The best results obtained were a concentrate analyzing 95.96% acid insol for a recovery of 65.98% after four stages of cleaning. With recirculation of cleaner tailings, the recovery would be higher.The possibility of using an alternative method, based on the natural ability of talc to float unaided by a frother/collector, was briefly explored with encouraging results.IntroductionBakertalc lnc ., located in the eastern townships at Highwater, Quebec, Is approximately 140 km east of Montreal near the Vermont, U.S. border. Originally called Baker Mining and Milling Co. Ltd., it has produced pulverized talc products since 1938(1 ), although records show that talc was mined in the area as early as 1871(2). Feed to the mill originally was obtained from local deposits, but since 1952 the van Reet mine near south Bolton, approximately 25 km from Highwater, has been the source of ore .In 1957 a Raymond high -side roller mill was installed which enabled production of a greater range of talc products and, in 1960, new crushing equipment and a dryer were added. Other additions to the mill were the introduction of wet magnetic separation, although this was later discontinued, and flotation to produce high-grade talc concentrates."

Jan 1, 1985

By D. R. Weir, R. M. G. S. Berezowsky

Pressure oxidation of gold containing concentrates and ores is an effective pretreatment for liberating refractory gold. This is particularly true when an appreciable portion of the gold is associated with sulfides and is not amenable to conventional cyanidation. A brief review of the literature on pressure oxidation of refractory gold materials is presented. The chemistry of the aqueous oxidation of arsenopyrite and pyrite is discussed. Data obtained on pressure oxidation and subsequent cyanidation of concentrates and ores tested at the Sherritt Research Centre are also presented.

Jan 1, 1985

By R. Frank Chiappetta, E. B. Wilson

"The maintenance records for AL-60 airlegs at Falconbridge Ltd. are used to demonstrate some of the procedures for the analysis of such data.The data are not representative of pure failure s of one type or another. In fact, the records are for the undefined pseudo-failures which are usually found in industrial operations. However, because the machines are brought to the shop only when inoperative, the individual recorded components are treated as failures. Manual calculations are conducted to show the analysis of variance (ANO VA) approach to determine whether certain data can be combined; only a limited number of the 206 machines being considered. The manual procedures continue with the weighting of the suspensions; i.e. terminations f or reasons other than the failure of the given component. After the data are sequenced in the proper order, the nature or pattern of the data is determined using the Kolmogorov-Smirnov (KS) test.It is recognized that these manual examples must be replaced by compute r methods 10 process voluminous data of this nature. Such programs are developed and available. However, a program called RELCODE is used in this case to correspond to the manual examples and to take into account the suspensions. These analytical procedures form the basis for those studies required for good maintenance management."

Jan 1, 1985

By Rahim G. Haghighi, Calvin J. Konya

Fragmentation is the fundamental concern of rock blasting, serving as a measure of blasting effectiveness. Fragmentation is sensitive to the inter-relationship among the design variables which define pattern geometry. Therefore, the objective of this study was to develop a model which represented a confined bench blast and to investigate the movement of burden-rock as the length to burden (L/B) ratio was varied.

Jan 1, 1985

By K. H. E. Kroemer

Selecting persons who are unlikely to suffer an overexertion injury is one of three methods to reduce the risk of musculo-skeletal disorders in manual material handling. This paper describes the underlying models, methods, and techniques for such personnel selection. In particular, it describes the isoinertial LIFTEST in which persons actually lift weights to assess their capability for doing so on the job.

Jan 1, 1985

By Corale L. Brierley

The depressed economic condition resulting from normal cyclic behavior, a more fundamental structural alteration, or both, is a mandate for change within the mining industry. Although several strategies for change have been proposed, the option of applying high technology processes to this smokestack industry offers the greatest opportunity for regaining global competitiveness and a new vitality. Research and development to secure new technologies require a corporate commitment for substantive change, a tech¬nologically enlightened management, a well¬funded and stable science and engineering effort, and a dedicated and motivated technical team--features in short supply in the mining industry today. However, an alternative to in-house development of frontier technologies is available to this beleagured industry through entrepreneurial, high-tech companies. These entities, with their dedicated focus toward product development, motivated and streamlined teams, high productivity and efficiency, and low costs offer a unique opportunity for large corporations to obtain high-tech products and services. These commodities are available through traditional commercial channels and an array of creative business arrangements. The latter offers notable benefits to large companies including windows on frontier technologies and mitigation of risk. Likewise, entrepreneurial companies profit through manufacturing and marketing relationships and an expanded financial base.

Jan 1, 1985

By A. K. Sinha

The market for thermal coal has recently been growing rapidly and it is projected to continue to do so in the foreseeable future. Both the national and international markets often demand high-Btu low-sulfur thermal coal in order to minimize the cost of utilization and meet the environmental restrictions. High quality thermal coal can be prepared to compete in the utility market by desulfurizing the high-Btu midwestern coal and blending it with low-sulfur western coal which is usually low in Btu content. The methods that can be used for optimizing the coal preparation plant operating parameters for physically desulfurizing coal are presented.

Jan 1, 1985

By J. Korak

Belt conveyor systems, long the standard transportation technique in soft-rock open-pit applications, are encountering growing interest in the hard-rock open-pit sector as economic factors force companies to seek an alternative to costly truck haulage. A general review of mine conveyor systems is followed by detailed analysis of the mobile and semi-mobile in-pit crushing plant essential to successful use of mine conveyors. A final section presents case studies of three crusher-conveyor systems handling overburden, copper ore and granite.

Jan 1, 1985

By M. E. Gershon

Conventional methods of drill hole site selection are reviewed briefly. Two approaches using geostatistics are then discussed, both of which have been shown to yield improved results. Finally, a branch and bound algorithm is described which will select the best locations for drilling from a user specified number of possible drill sites. Two options are discussed. First, the user can specify a maximum drilling investment or a maximum number of drill holes and the program will select the locations yielding the minimum estimation variance. This amounts to getting the most for a given investment. Alternatively, a maximum tolerable estimation variance can be specified and the program will select the number and location of the drill holes to obtain the desired information at a minimum cost. Another benefit of the approach is the quantification of the tradeoffs between investment and information obtained.

Jan 1, 1985

By G. W. Riley, D. E. Pickett

HINDERED SETTLING CONCENTRATION In the free settling of mineral particles in a liquid, the falling particles are at a distance from each other so that no particle is affected by its neighbor. In hindered settling, the concentration of particles is sufficiently high so that each particle is affected by its proximity to other particles in the suspension. Richards and Locke86 have described the hindered settling phenomenon as the condition “.. where particles of mixed sizes, shapes and densities in a crowded mass, yet free to move along themselves, are sorted in a rising current of water, the velocity of which is much less than the free-falling velocity of the particles but yet fast enough so the particles are in motion." This is the condition normally encountered in mineral con¬centration processes. The well known Newton equation for free settling of coarse (ap proximately +10-mesh, 1/16-in. or -- 2000-µm) spherical particles is:87 where v," is free settling velocity, cm/sec; p' is density of the fluid; p is density of the particle, g/cm3; d is particle diameter, cm; g is acceleration due to gravity, cm/sec2; and Q is coefficient of resistance, dimensionless, ~0.4. For the settling of fine spheres in water (approximately 150 mesh or 100 µm) the equation of Stokes pertains:87 where µ is viscosity of the fluid in poises and the other symbols have the same meaning as those in Eq. 1. For particles whose size lies between about 10 mesh (--2000 µm) and 150 mesh (100 µm), their settling velocity can be determined from experimental data. These data are available in convenient form in the text by Taggart88 based on the original work of Richards. Alternatively, a Reynolds number-coefficient of resistance plot may be used to determine the settling rate of such particles.87 The settling rate of spherical particles under hindered settling conditions can also be calculated from Eqs. I and 2 by replacing p', the density of the fluid, by p" the apparent density of the suspen¬sion. The concentration of particles in the fluid thus imparts an appar¬ent density to the composite fluid or suspension greater than that of the liquid alone, resulting in a buoyant effect on the larger particles. Particle shape affects the settling rate of both coarse and fine particles. The general effect is to reduce their settling velocities and the effect is greater for coarse particles and for those settling under hindered settling conditions than for fine particles or free settling ones. For two particles of differing densities but settling at the same velocity under Newtonian conditions, the ratio of their diameters from Eq. 1, called the free settling ratio is: where L signifies the lighter particle and H, the heavier particle. Under Stokesian conditions the exponent would be 0.5. For hindered settling conditions the fluid density p' is replaced by the apparent density of the suspension, p", to obtain a generalized equation for the hindered settling ratio: assuming both particles settle in approximately the same regime. The free settling ratio as given by Eq. 3 has been called by Taggart88 the "concentration criterion" and is used to predict the effectiveness of any gravity concentration process (see Introduction to this section). Based on Eqs. 3 and 4, if two particles of densities pH and p,, settle at the same velocity, the diameter of the lighter particle will be larger than that of the heavier particle. For example, in the case of galena (pH = 7.5) and quartz (pL = 2.65) settling in water (p =1.0) under free settling, Newtonian conditions 3.9. Thus, a quartz particle nearly four times as large as a galena particle will settle at the same velocity. Any quartz particle just slightly less than four times the diameter of the largest galena particle may be separated from it. Under hindered settling, Newtonian condi¬tions in a suspension where p" = 1.65, dL/dH = 5.85 or any quartz particle just slightly less than about six times the largest galena particle may be separated from it. Reference to Eq. 4 indicates that a superior separation between two minerals of differing densities is favored by: (1) coarse particles settling under Newtonian conditions, (2) a large difference in (pa - PL), and (3) separation under hindered settling conditions where p" is high. Of course, there are practical limits to increasing p" excessively because at very high percent solids suspen¬sion fluidity would be lost and the hindered settling separation process defeated. Examples of hindered settling separators are the Dorrco-Fahren¬wald sizer,89 the Rheolaveur box 90 the Spitzkasten,89 and the Willoughby washer.91 These devices make a mineral separation on the basis of both specific gravity and size and all of them are essentially obsolete except for the Dorrco-Fahrenwald sizer and similar devices which still find application for the removal of coarse particles from a much finer particle assemblage and for preconcentration ahead of shaking tables. However, nearly all gravity concentration processes (jigs, tables, flowing film concentrators, heavy media separators) and many sizing devices (sizing classifiers, clarifiers, thickeners, hydrosepa¬rators) make use of the hindered settling phenomenon during the separation of particles. JIGGING Introduction In jigging, a mixture of ore particles, supported on a perforated plate or screen in a layer or "bed" with a depth many times the thickness of the largest particle, is subjected to an alternating rising and falling (pulsating) flow of fluid with the objective of causing all

Jan 1, 1985