Search Documents

By M. Leroux, S. R. Rao, J. Kim, V. Gervais, J. A. Finch, G. Labonté, N. Macminn, M. Ounpuu

Collectorless flotation of sulphide minerals from Lyon Lake ore (Mattabi Mines Ltd.) has been studied both in the laboratory and plant. Among the four major minerals chalcopyrite showed the greatest response to collectorless flotation, followed by galena. Flotation of sphalerite and pyrite was minimal. Collectorless flotation was influenced by pulp potential and pH. Experiments using different gas compositions showed collectorless flotation was promoted when the pulp potentials were greater than about 0 mV (SCE). The study of the effect of depressants showed that SO2 at pH < 8.0 depresses both galena and chalcopyrite but at pH 9.5 flotation of chalcopyrite recovers. Use of NaCN preferentially depressed chalcopyrite compared to galena. Preliminary results from plant tests at Mattabi Mines Ltd. confirm that collectorless flotation occurs and that it is preferential for chalcopyrite and to a lesser extent galena. Practical implications of collectorless flotation in plant practice are discussed. A critical factor will be silver recovery.

Jan 1, 1989

The relationship between the permeability of coal to a mixture of methane and carbon dioxide, and the permeability to methane and carbon dioxide separately is described in this paper, along with the analysis of the differences in permeabilities of coal to methane and carbon dioxide.

Jan 1, 1989

By Clyde Baker

Drilled shafts for many situations offer an economical alternative to driven piles. The Federal Highway Administration (FHWA) has spent considerable time and money in research and developing design and construction guidelines for drilled shafts. However, the full potential of the technology may not be realized because of the uncertainty of the effects of construction on the actual service behavior and the lack of either reliable quality control tests to check for or evaluate defects, or inexpensive load test procedures. Static load testing is very expensive and it is not feasible to load test each shaft on a project. Therefore, other means are necessary to confirm or evaluate the integrity of the completed drilled shaft or to determine the capacity of the completed shaft.

Jan 1, 1989

By Alan P. Prosser

The heap leaching of gold ores by cyanide solution was simulated by computer program. The program uses only basic m1neralogical and chemical data; no process testwork data, such as column leach results, are required. The simulation can be used to forecast the consequences of various changes before and during the testwork, design and operation stages of a particular ore-process system. Also, data about the state of different parts of the heap at various times help create an understanding of what is happening. The effects of mineralogical and process variables on the overall performance of the ?heap leaching process are illustrated. Comparisons are made to column leach tests and production data. The potential of the simulation strategy is discussed for making better use of operating experience and for suggesting specific research objectives. It has become clear that more attention should be paid to other metals that dissolve in the solution.

Jan 1, 1989

By Thomas J. Ferree

"IntroductionThe objective of this chapter is to provide important criteria relating to the operation and maintenance of spiral concentrators and Reichert cones, so that optimum performance can be achieved and maintained in a mill circuit. Little space will be devoted to the theory of the forces of separation or the technical details of the devices, as that in(ormation is available from other sources. The discussions in this chapter will be presented in a manner that should be interesting and useful to anyone who may be exposed to these methods of gravity separation. It is most important for the reader to understand that each application of the equipment should be considered on its own merit, as no two suites of minerals respond exactly alike in mineral processing circuits. The information herein should be useful as a guide toward increasing the metallurgical efficiency of the processes, irrespective of the type of minerals being concentrated.It is highly recommended that certain tools be made available to the personnel responsible for metallurgical performance of the spirals and cones; these include a set of standard type laboratory screens, a medium quality petrographic microscope, and a vanning plaque or gold pan. These devices, when used in conjunction with a basic understanding of the mill circuit, provide immediate knowledge on the characteristics of any sample in the mill circuit. The information gained by visual evaluation of sized fractions of products can solve many of the basic problems of mineral beneficiation, and at the same time increase the interest of the non-technical personnel associated with the plant operation. There are many problems associated with obtaining satisfactory performance from a mill operation. Many of the problems have to be solved using a technical approach. Some of the problems, however, can be solved with practical knowledge and common sense. It is hoped this chapter can provide a guide to both techniques."

Jan 1, 1989

By George A. Savanick

The U.S. Bureau of Mines has patented and transferred to industry an abrasive-enhanced water-jet rock drill. This drill incorporates three novel components: a collimator, jet deflectors for cutting clearance, and an unpressurized swivel, which rotates at 1,000 rpm while passing 20 gpm of an abrasive slurry flowing at 1,000 ft/s. Drilling occurs through the action of a 10,000-psi, 2O-gpm water jet into which is entrained 72 lb/min of abrasives. The pumps, hoses, and fittings are those commonly used in the water-jet-cleaning industry. Only inexpensive, common sandblasting abrasives are used. This drill can cut through hard rocks with moderate-pressure jets; e.g., rocks with a compressive strength of 73,000 psi can be drilled with a 1O,OOO-psi abrasive jet. In addition to drilling holes, the drill can cut deep, narrow kerfs; collar a hole at any angle; drill through rubble; and chamber holes. The development of the abrasive jet drill is a significant advance in the state of the art of hard-rock drilling. The Government of the United States has licensed the abrasive jet drill patent to Weatherford Water Jetting Systems.

Jan 1, 1989

The geographical region of South East Asia is variously defined, but generally agreed to include the Asean group - Philippines, Malaysia, Thailand, Singapore and Indonesia. Other regional countries, such as Vietnam, Laos, Burma, Kampuchea etc. are of course geographically part of the region, however in economic terms, they play a minor role. It is the Asean group that dominates present economic activity and provides the overwhelming opportunity for commercial development. My experience in South East Asia has been gleaned over 15 years of regular travel in the region. More recently, we have established company offices in Malaysia, Singapore and Indonesia to extend and deepen contacts with major customers. This progressive development is an integral part of a planned growth pattern and will be discussed in more detail shortly. South East Asia is a rapidly developing economic growth centre, a fact which is clearly recognised and accepted by most commentators. An important question is then to be asked: Why has the region been relatively neglected by Australian, U.S. and European industrial supply companies? I will attempt to address this question in the context of industrial minerals and propose some ideas as to how effective sales programs could be developed. Firstly, let&apos;s consider the market potential provided by countries within the region. It is reasonable to suggest that industrial growth in S.E. Asia over the past 20 years has been generally steady and in some cases, explosive. Until recently, this growth has predominantly been driven by development of internal (regional) demand. Population growth and rising living standards have ensured that basic industries have enjoyed a solid uptrend in sales and production. The industries which most benefitted from regional economic development over this period were, interestingly, those which we understand to be major users of industrial minerals - glass, ceramics, paper, surface coatings, cement, refractories, rubber and plastics. Each of these industrial sectors has been influenced by different growth stimulii over a 20 year period. Nevertheless, they also enjoy a common feature which ensured an above average performance. All sectors are fundamental to an environment enjoying rising living standards and rapid growth in general prosperity. More recently, internal growth factors have been overtaken by a recognition that manufactured products from the region are competitive in export markets. This comparatively recent development provides the most interesting possibilities for higher value industrial mineral raw materials. Let me explain: For 20 years, industrial growth in South Asia has essentially been focused on satisfying domestic demand. Finished quality of manufactured items was orientated to a developing market more interested in cost than aesthetics or long life. This was reflected in raw material specifications, which often did not exist and at the best were undemanding.

Jan 1, 1989

The reduction in man&apos;s contribution to the Greenhouse effect will only be achieved by a number of small steps. Some steps will absorb carbon dioxide (CO2) from the atmosphere in slightly greater quantities, others will reduce the amount of carbon dioxide generated. This paper deals with the reduction of carbon dioxide by improving the combustion efficiency of petroleum fuels. Until recently most reductions in fuel consumption and air pollution have been brought about through mechanical adjustments to combustion equipment. Since the development of tetraethyl lead, little has been done to chemically modify combustion reactions to improve fuel efficiency or reduce emissions. During the past five years Australian laboratory and field trials with ferrous picrate treatment have demonstrated significant and economic gains in the combustion efficiency of diesel fuels. These studies have revealed that even under ideal conditions in diesel engines, carbon monoxide (CO) momentarily saturates the combustion chamber. This state reduces combustion rates, peak pressure and power and increases the risk of pollution. Theoretical, laboratory and field data are presented which support the mechanism by which the ferrous catalyst accelerates the oxidation of CO to the terminal CO2 thus reducing fuel consumption and the undesirable combustion products accompanying the CO saturation of combustion environments. While this paper deals principally with diesel fuels commonly used in mining operations, the catalytic effect of the ferrous ion is also shown to significantly reduce fuel consumption by petrol engines thereby promising a means to reduce the much larger contributions to the Greenhouse gases by automobiles.

Jan 1, 1989

By M. A. Gerdel

In carboxylate collector flotation of bastnasite from other semisoluble salt type minerals such as barite various modifiers must be added in order to achieve selective flotation. One such modifier is a lignin sulfonate. It may function in part by acting as a sequestrant for metal ions present, preventing autoactivation in the system by metal ions derived from the minerals themselves. It also functions as a depressant for both bastnasite and barite, chemisorbing on both. However, it is shown that the lignin sulfonate functions as a much stronger depressant for barite than for bastnasite. It is suggested that the; strong depressing action on barite is related to a good fit of the sulfonate into the barite structure.

Jan 1, 1989

By N. Dave

"IntroductionIn the mineral processing industry, certain minerals such as uranium, thorium and vanadium, etc., are selectively extracted with high degree of purity from solutions containing variety of other impurities by solvent extraction process. This separation process consists of bringing two immiscible or partially soluble liquid phases in contact, where mass transfer of one or more components takes place by ion exchange under certain controlling parameters such as pH, salt concentration and temperature. The processes taking place are primarily physical because the solutes being transferred are ordinarily recovered without chemical change. For efficient extraction more than one stage is required and the solutions are recycled counter currently through other stages. A multi-stage counter current solvent extraction plants essentially consist of four circuits namely: extraction, water wash, stripping, and solvent scrubbing. In extraction circuit the desired mineral is extracted at a certain pH from an aqueous solution onto an organic solvent by bringing them in contact with mixing in large mixer-settler units. The mixed solutions are allowed to settle and separate into component organic and aqueous phases in horizontal settlers by providing sufficient residence time. The solutions are then moved counter currently to other units- the aqueous from the underflow and the solvent organics from the overflow of the settler. The solution streams coming out of extraction circuit are loaded organics and barren aqueous or raffinate solution. The loaded organics are washed with water in a water wash circuit to remove transported impurities from extraction circuit. In the stripping circuit, the desired mineral is stripped selectively from the solvent phase back into an aqueous phase with a stripping agent at a selected pH. The solution stream leaving, stripping circuit are stripped organics and pregnant strip (aqueous) solution. The stripped organics are scrubbed off other loaded impurities with a conditioning solution in, scrubbing circuit and the cleaned solvent is re-used in the extraction circuit.A typical solvent extraction plant for uranium extraction and purification at Agnew Lake Mine is described in this chapter."

Jan 1, 1989

By P. Cielo

"Nondestructive inspection is an important quality control tool in the material processing industry. Being nondestructive, such a control may be applied to the whole production, as long as the available techniques are fast and easily automated. Ideally, nondestructive testing (NDT) methods should operate in a noncontact configuration in order to be deployable on-line with minimum perturbation of the production process.After a short introduction to the most common NDT techniques, with particular emphasis on ultrasonic, radiographic and electromagnetic methods, a few new approaches which are under development at the Industrial Materials Research Institute, (Boucherville, Quebec), are reviewed. Noncontact techniques such as laser ultrasound, thermoelastic and thermographic methodologies will be described, and their applications to materials of industrial interest will be discussed."

Jan 1, 1989

By George S. Koch

Today, after about 30 years of development, computer-based analysis of geoscience data has reached a mature phase. From the tentative early beginnings recorded in the proceedings of the APCOM meetings, geoscientists are now able to emphasize the need for both pertinent mathematical/statistical models and computer hardware and software. From those models that are well understood in the disciplines of statistics and mathematics and for which effective computational methods are available, practitioners select and develop methodology for their particular purposes. Computer hardware is typically assembled from off-the- shelf components now readily available, with particular emphasis, whenever feasible, on microcomputers for reasons of economy and control by the scientific or engineering user rather than by a bureaucratic computer center. Computer software may be written by the user in high level languages such as Pascal, FORTRAN, or LISP. However, more often today geoscientists use routines available in spreadsheets, data bases, or statistical packages. In so doing, they save time and, programming costs and take advantage of routines written and maintained by large, well- established organizations, while losing the flexibility in specifying exact input/output afforded by writing in a high level language.

Jan 1, 1989

By Travis S. Wellman, Jon C. Volkwein

The Bureau of Mines conducted a study to assess the impact of a directional water spray system on a unique single inlet dust scrubber on a low profile mining machine. Tests were conducted in a full scale model mine using a Joy 12 CM 10-AA continuous mining machine. Tracer gas was introduced at the face and concentrations of the tracer gas were monitored at the face and in the return. Various parameters included: mining position, depth of cut, brattice setback and combinations of scrubber, directional sprays or symmetrical sprays. Results indicated that either directional or symmetrical water spray configuration improved the ventilation effectiveness of the scrubber by a factor of 2 to 3. Average face ventilation effectiveness (FVE) values for all testing of the scrubber and directional sprays were 0.95, versus 0.37 for a standard 6 m (20-ft) blowing curtain without sprays. No FVE values were less than the standard 6 m (20-ft) blowing results.

Jan 1, 1989

By O. Neves, C. G. González Beca, M. C. Sol Pereira, H. Sousa Vale, R. A. Guedes de Carvalho, M. N. Sampaio

"As sulphide ores are usually concentrated by flotation , the material is very finely ground <37um), wet and impregnated with the chemicals used in flotation. These conditions are favourable to the development ofchemical reactions which are largely influenced by atmospheric conditions (temperature, humidity, wind, etc.) as well as by the geometry of the piles.Physical and chemical properties of a chalcopyrite concentrate were determined by laboratory tests. The knowledge of these properties was considered necessary in order to establish a correct design of the storage and handling operations of the sulphide ore concentrates obtained by flotation.The properties studied in this work were: transportable moisture limit, flowability, effects of vibration, hygroscopicity, ""caking"", chemical alterations by humidity, oxidation and self-heating (auto-ignition, dry and wet oxidation, self-heating by humidification and its prevention).INTRODUCTIONIn order that the handling and the transport of a powdered material may be carried out correctly, it is necessary to know certain physico-chemical characteristics. Transportable moisture limit (TML), apparent density (both aerated and compacted), compressibility, angle of repose, angle of spatula, cohesion and angle of slide(l-4) are characteristics (among the flowability parameters) worth knowing.Moisture content of the powdered material is fundamental, because if this is too low heavy losses will occur when the product&apos;s particle size is very small, if it is too high, separations between solid and liquid phases may occur. In the latter case, the centre of gravity of the system may change suddenly and cause accidents, mainly if transport is by sea or by river."

Jan 1, 1989

By R. J. Matetic

The Bureau of Mines, as part of a program to improve mine planning and development, is currently investigating the effects of pillar load transfer, which can impact mining operations within a multiple-seam configuration. A comparative study was performed at two separate mine sites to determine the effects of this load transfer mechanism. The Bureau installed and monitored instrumentation at both sites to gather pertinent data on rock mechanics. At mine site A overburden depth varied dramatically in the vicinity of the study area and reached a topographic high at the study site: inner burden thickness was less than a pillar width (40 to 45 ft) (12 to 14 m): floor heaving was experienced in both coalbeds where sandstone and/or shale floor units were observed: overlays of the mine layouts show pillars were not totally super-positioned: a maximum of 5 in (13 cm) of roof to floor convergence was measured and pressure readings indicated pillar core loading only and increased to a maximum of 7,000 psig (48,300 kPa) over instrument setting pressure.

Jan 1, 1989

By Leonard A. Wolff

"The 1980sfor the mining industry can be characterized as the survival of the fittest. High interest rates, low commodity prices, foreign subsidized competition and decreasing ore grades have contributed to a streamlining of the domestic mining industry in the United States, leading to the shutdown of operations or large cutback of work forces. The purpose of this paper is to look at the impact of a layoff on the employees of what was once a major uranium producer in south central Wyoming, twenty months after the final layoff and mine shutdown. INTRODUCTIONDecember 19, 1985, was the date of the final of three successive layoffs over a two-month period, leading to the complete shutdown of Petrotomics Company, a subsidiary of Getty Minerals Company. The final shutdown was due to a combination of depressed U3O8 prices and the takeover of Getty Oil Company by Texaco in January 1984.The layoffs affected 104 employees and included mine personnel, mill personnel and staff. Both hourly and salary workers were involved. The operation was considered non-union, however, a few mill hourly employees were unionized. At the completion of the layoffs. only a handful of employees remained for administrative and miscellaneous functions.For Getty employees, the terms of the merger agreement provided a generous level of separation benefits. The terms that were insisted upon by Mr. Petersen, Chairman of the Board for Getty Oil, stipulated that employees receive one month of severance pay, for each full calendar year of employment up to a maximum of two year&apos;s pay. This was the forerunner of what is now commonly known as the ""tin parachute”. All but the union employees of Petrotomics received these separation benefits. Union employees were covered by their separate, less generous, contract.Much of the literature that has been published in recent months has centred around the effects of layoffs on remaining employees, or the psychological effects on the severed employee. This study will emphasize the economic impact and ramifications due to a layoff, using the Petrotomics employees as a case example."

Jan 1, 1989

By M. C. Fuerstenau, J. J. Fitzgerald

Aluminum silicate hydrosol synthesis and characterization are discussed. Plausible polymeric aluminosilicate species are presented together with their effect on electrokinetics of selected minerals and flotation response of various ores. The addition of aluminosilicate hydrosol to porphyry and oxide copper ores and to a tungsten ore resulted in enhanced flotation recoveries ranging from about 1.5 to 5 percent. A significant portion of the nation&apos;s mineral resources are presently lost in the form of particles with very fine grain size. In the case of copper, for example, approximately 225 million tons of ore are concentrated by flotation per year in the United States. Total losses from porphyry ores are generally 15 to 20 percent with half of these losses being finely-divided copper sulfide minerals which do not respond to flotation. The additional 5 to 10 percent loss is the result of copper oxide minerals which are not floated. The losses of copper sulfide minerals are thought to be due in part to the lack of appropriate dispersion of the finely-divided solids less than 20 microns in size. To effect dispersion in flotation systems, sodium silicate is commonly added. Enhanced dispersion effectiveness is achieved when polyvalent metal salts are combined with sodium silicate. Since originally described by Patek (1), numerous workers have explored the utility of metal silicates. Makrousov (2), Belash et al. (3), and Eigeles (1950) (4) showed the applicability of these reagents to calcite/apatite and fluorite/calcite ores. Mercade (5, 6) reported depression of calcite in the presence of 3.33/1 mole ratio Al/Si hydrosols prepared from Type N sodium silicate (Si02/Na20 ratio 3.22/1) and 1% A12(SO4) 3•18H20 solutions. He importantly observed that the colloidal precipitates did not play a significant role in dispersion and depression but that the soluble species were responsible for this action. Patented work by this author described metal silicates used to depress calcite in scheelite flotation using 1% metal salt (FeSO4•7H2O, CoSO4•7H2O, etc.) and 5% Type N sodium silicate solutions to produce hydrosols with Si/Fe or Si/Co ratios of 8.79/1. Aluminum (III) ion systems were less effective as depressants than the iron and cobalt systems. Yang (8, 9) has studied metal silicate sols for use in the flotation of lithium and ultra-fine hematite ores. Using 10/1 Si/Fe mole ratio hydrosols prepared from 2% ferric nitrate, Fe(NO3)3.9H20, and 5% Type N sodium silicate solutions, solutions, he showed that the hydrosols either modify the slime particle surfaces or are adsorbed on the slime particles preventing anionic collector adsorption. In a subsequent patent, Yang also reported the use of these hydrosols as dispersants for beneficiation of lithium ores. Recent studies of aluminum silicate hydrosols in the flotation of chalcocite, chalcopyrite and scheelite have been reported using Si/Al dispersants prepared from 5% Type N sodium silicate and 0.1 M aluminum chloride (A1C13.6H20) solutions. Dispersant properties were shown to be dependent upon the method of synthesis, supernatant pH, and the hydrosol Si/Al mole ratio. Polymeric soluble species in these hydrosolsupernatants have been proposed as the active dispersant species. Aluminosilicate hydrosols are synthesized by the general reaction scheme presented in Figure 1. Commercial sodium silicates are available with ratios of SiO2 to Na20 of 1.60-3.25. The sample which is most frequently employed is Type N whose ratio of Si02/Na20 is 3.22/1.00. Gel filtration chromatography and NMR studies have shown that these sodium silicates contain numerous species of molecular weight from 325-2,000 gm/mole. Monomeric, oligomeric and higher molecular weight linear polymeric arrangements of these structures are found in these solutions.

Jan 1, 1989

By Donald D. Haas

This presentation will discuss a mine owner&apos;s evaluation to utilize a contract miner in the development and production of gold properties. I will address both the quantitative and subjective aspects of the evaluation process. The quantitative aspects include cost evaluation, capital preservation, acquisition and disposal of new and used equipment, administrative costs, recruiting and training, and organizing a staff and craft labor force. The subjective areas of this discussion include corporate philosophy, administrative concerns, contractor competence, loss of owner control, operating flexibility, financing assistance, recruiting and training program utilization and risk reduction. The evaluation of alternatives provides a system for comparing, on a cost basis, an owner/operator system vs. a system using a contract miner. The supplement provides a concept on how a contract miner may be the cost effective system to be utilized.

Jan 1, 1989

By C. E. Jordan, B. J. Scheiner

The Bureau of Mines conducted research on the flotation hydrodynamics of fine particle flotation to improve the flotation efficiency in our domestic minerals industry. The turbulent fluid velocity profile was measured in various flotation cells at different levels of dissipation energy. The importance of dissipation energy and bubble size within the flotation cells for the flotation response of a chalcopyrite ore was evaluated. Both increased turbulent fluid flow and fine size bubbles improved the flotation rate of fine size chalcopyrite particles.

Jan 1, 1989

By J. Brent Hiskey

Carefully prepared gold-bearing arsenopyrite samples from different geographical locations were leached in alkaline cyanide solutions using an electro-dissolution technique. Special precautions were taken to utilize monosized and thoroughly characterized samples. The rates of iron, arsenic, gold and silver dissolution were measured as a function of temperature under controlled conditions in sodium cyanide media.

Jan 1, 1989