Search Documents

By J. Hanna, R. Kalathur

Over the years, Alabama's coal industry has generated, during mining and cleaning operations, about 150 million st of fine waste coal, with this total increasing at a rate of 2 million stpy. Reclamation of the fine-size wastes (containing 20% - 60% clean coal by weight) provides, free of charge, mined and crushed feed stocks for coal recovery. Also, the removal or recovery of pyrite from the tailings should eliminate a major source of acid-water pollution. Tests were made on the impounded wastes and current plant discharges to recover the coal fraction by sizing, gravity and flotation techniques. Gravity separation of the +100-mesh material produced commercial-grade coal averaging 7.6% ash, 0.8% sulfur and 13,471 Btu/lb. However, the coal yield, at about 31 % - 56%, was relatively low. Froth flotation, using mechanical and froth column methods, gave similar coal products at much higher coal recovery rates of 87% - 93%. This coal analyzed 10% ash and 1.1% sulfur.

Jan 1, 1993

By Thomas J. Feeley

The US Department of Energy (DOE) is supporting the engineering development of three advanced physical coal cleaning technologies: selective agglomeration, advanced flotation and advanced cycloning. Each is capable of significantly reducing the pyritic-sulfur content of US coals. The objective is to provide the coal and electric-utility industries with a cost-effective option for addressing the SO, emission reductions required by the 1990 Clean Air Act Amendments (CAA). A secondary objective is to evaluate the potential of advanced coal cleaning for removing trace elements that are precursors to the formation of hazardous air pollutants (HAS). The proposed National Energy Strategy (NEE) and the 1990 CAA lay a foundation for a more efficient and environmentally sustainable energy future (1991). The need to use energy resources in an environmentally sound manner presents critical challenges and opportunities for coal preparation during the next decade, particularly regarding the control of SOS and HAY emissions. The principal challenge is the development of cost-effective coal preparation approaches for sulfur and HAY precursor removal.

Jan 1, 1993

By M. J. Richards, T. X. Ren

Determination of the state of an underground fire plays an important role in fire fighting, rescue and reopening operations. This is normally achieved by the analysis and interpretation of fire gases taken from the fire zone. However, drawing conclusions from gas analysis is not an easy task and needs specialist skills, expertise and experience that are usually beyond the knowledge of the officials in a mine. The complexities of a mine fire and the uncertainties of available information often make effective fire fighting decisions difficult if not impossible. This paper describes a knowledge based expert system that can aid in the diagnosis of sealed coal mine fires. Using a commercially available shell, the expert system has been designed to accommodate a series of diagnostic rules replicating the reasoning logic that would be used by human experts. The system allows the diagnosis of explosibility of the fire zone and trends of various fire ratios to be easily visualised for decision making. By continuously analysing the incoming information, the system is able to provide a rapid assessment of the situation of a sealed mine fire prevailing under specific mining and geological conditions. In addition, short term trends in fire behaviour can be predicted and possible fire control actions recommended. An example is given and shows how this system can be used as an analytical tool in various ways to assist the combating of coal mine fires. Further development of the system is discussed.

Jan 1, 1993

By Roy S. Nutter

The automation of coal mining must occur in a manner that is economically beneficial to the industry and that enhances the safety of the underground and surface workplaces. The work at WVU over the last five years in applying expert systems and neural network controlled autonomous robotics provides the mining industry with tools that when properly applied should clearly lead to mine-wide management and operational improvements and should also contribute to a higher awareness of safety issues by all work crews. This work includes the development of MMSS (Mine Management Support System) and the detailed development of autonomous robotics utilizing neural networks for mining systems.

Jan 1, 1993

By C. A. Hesse

The Quartz Hill Molybdenum Project, In Southeast Alaska, was the first mining project to attempt the permitting of a submarine tailings disposal system in the United States, since the passage of the National Environmental Policy Act of 1969 and the Clean Water Act of 1977. Over $20 million was spent by the project developer in baseline data gathering and In funding the preparation of the four Environmental Impact Statements and other environmental documents required at various stages of the project between 1977 and 1988. Because of the timing and a unique set of environmental, legal and regulatory requirements which applied to this project, innovative approaches were developed. This report describes those requirements and the developments, and gives a full historical account of the campaign for permitting submarine tailings disposal at Quartz Hill, until denial of the NPDES permit application by EPA in September 1 990. The extensive studies done for Quartz Hill suggested that under certain conditions the selection of submarine tailings disposal can be the overall environmentally preferred alternative for a mining project. The Quartz Hill story illustrates the complexity of the existing permitting structure and paints out the desirability of rationalization to achieve a more effective system.

Jan 1, 1993

By George A. Morgan

The 53 countries that constituted Africa in 1991 accounted for a significant portion of total world output of a number of mineral commodities. However, total output for the continent declined for many major mineral commodities produced compared with that of 1990. Also, Africa's share of total world output of these commodities generally declined. (See tables 1 and 2.) The most conspicuous declines were for cobalt and copper owing to mining and metal processing difficulties experienced by the world's two largest cobalt producers, Zaire and Zambia. Phosphate rock output declined primarily owing to a sharp fall in production from Morocco, also a leading world producer. Morocco's state corporation for phosphate production experienced marketing problems, leading to the decline.

Jan 1, 1993

By Michael J. Klishis

Accident rates continue to show that underground mining jobs areamong the most hazardous occupations in the United States and roof bolter operators continue to have one of the highest accident incident rates (MSHA, 1991) despite efforts by labor, government, and industry to reduce and eliminate work-related hazards. In the last two decades we have seen technical innovations such as the ATRS, and there has been an increased emphasis on hazard awareness through programs such as MSHA's REAP, but bolter operators continue to be injured and killed. Researchers at West Virginia University examined risk in the roof bolter's job and developed new approaches to accident and injury prevention. The study concentrated on the workers' job performance, machinery and the work environment to identify miner's risk and hazard exposure while bolting.

Jan 1, 1993

By Terry R. Neumann

This document, prepared for the U.S. Bureau of Mines Regional Mineral Assessment Program, presents data pertinent to the mineral resource assessment of the Needles 1° x 2° map quadrangle (excluding the Arizona portion), located in the Mojave Desert southeastern California. The U.S. Bureau of Mines (USBM) mineral survey of the quadrangle, conducted from 1991 to 1993, was done to provide the minerals data necessary to support effective land use planning and resource decision making. To this end, this report (1) inventories historic and current mining activity, (2) inventories identified resources, (3) provides an economic analysis; of identified mineral resources and estimates their feasibility for development, (4) delineates areas of exploration and development potential based on current geological, geochemical, and geophysical information, (5) supplies information on land status, transportation networks, power supplies, water availability, and regulations, and (6) analyzes socio-economic impacts of potential mining. The Needles quadrangle is in the Basin and Range province of the southwestern United Van. The area is underlain by a lithologically and structurally complex Proterozoic crystalline basement of gneiss and granite that is overlain by sparse, scattered outcrops of deformed and metamorphosed Late Proterozoic and Paleozoic sedimentary sequences. Mesozoic granitic plutons, particularly in the western half of the quadrangle, intruded the basement and sedimentary rocks, resulting in metamorphism and deformation responsible for the formation of high-grade gneisses and mylonitic rocks (core complex) in the eastern part of the quadrangle. Voluminous Tertiary volcanism unconformably overlie some older sequences. The structure of the area is dominated by Basin and Range extensional block faulting; in the eastern part of the area, block faulting is accompanied by widespread low-angle detachment faulting associated with core complex development.

Jan 1, 1993

By Jr. Boyle

This report analyzes the availability of chromium in the form of ferroalloy products (high-carbon and low-carbon ferrochromium and ferrochromium-silicon) and chromite products (metallurgical, chemical, refractory, and foundry sands) in market economy countries (MEC's). A total of 873.5 Mmt of in situ material, containing 202.5 Mmt of chromium, in 10 MEC countries was analyzed for availability as of the January 1989 study date. Extraction and beneficiation of this in situ material would result in 475.4 Mmt of marketable chromite products. As analyzed, 288.5 Mmt of these chromite products would be available for export or for internal chemical and refractory use and 186.9 Mmt would be smelted in-country to produce 74.3 Mmt of high-carbon ferrochromium, 3.9 Mmt of low-carbon ferrochromium, and 2.0 Mmt of ferrochromium-silicon, all available for export. A network flow model, which includes centrally planned economy countries (CPEC's), was also constructed to analyze world chromium supply and demand interactions for the period 1986 through 1994 and to address a hypothetical North American embargo on direct imports of all South African chromium products beginning in mid-1990. The model shows capacity constraints developing in the MEC high-carbon ferro chromium industry in 1987 and a possible subsequent overreaction by the industry in terms of new capacity additions. The results suggest that sufficient chromium is available to North America should an embargo on direct imports from South Africa be imposed by its governments. However, the effect on export revenues in South Africa is relatively small, and timely increases to world ferrochromium, chemical chromite, and foundry sand chromite capacities would be required.

Jan 1, 1993

A major highlight of Fiscal Year 1993 is the completion of a new research facility dedicated to the advancement of robotics research and development. This new facility brings to the U.S. Bureau of Mines one of the largest and most unique facilities of its kind in the world. Located at the Bureau's Pittsburgh Research Center, the facility consolidates under one roof, all of the resource requirements of a first class automation and robotics research program. The Mining Robotics Development Center (MRDC) is the result of a major renovation of a large under-utilized warehouse-type structure and brings together the laboratories and offices previously housed in five separate buildings scattered throughout the Pittsburgh Research Center's 238-acre site. This new facility will support the computer-assisted mining research program, a high priority, multi-million dollar program that is expected to have a high impact on the health and safety of miners and coal productivity.

Jan 1, 1993

By Orlando Martino

This regional report covers the mineral industries of Canada and 40 countries and areas in Latin America and the Caribbean Basin. Also included is a brief description of the mineral potential of Antarctica. The Latin American region encompasses an area twice that of the United States. Latin America and Canada have a rich and diversified endowment of mineral fuels, metals, and industrial minerals. Tables 2 and 3 provide a summary view of the importance of Latin America and Canada's output of its major mineral commodities in world mineral supply in 1989 and 1990.

Jan 1, 1993

By Mark L. Chatman

The U.S. Bureau of Mines studied mineral resources of the Dragoon Mountains Unit, Coronado National Forest (54,264 ac), Cochise County, AZ. This study involves literature and field investigations with a focus on mine and prospect sites, which were inventoried and mapped; maps are contained in this report. Rock-chip samples were taken from mineralized zones and from some mine dumps; assays of the 477 samples are in appendixes. Mineral deposits are genetically and spatially related to Tertiary-age granitic intrusive activity. Most metallic mineral deposits are also strongly fault-controlled. Colored marble resources (270,000 st) are valued at approximately $6.5 million, if all were to be developed and sold as landscaping material in the form of-marble chips. However, with current demand, it is unlikely that regional markets could absorb all this material. Economic modeling of copper-zinc-silver skarns suggests none would be profitable to mine and capitalize at early 1993 commodity prices, mainly due to the small estimated size of the deposits (30,000 st to 40,000 st maximum). In the entire Unit, 140,000 st of inferred subeconomic skarn resources were estimated by USBM on five different skarn trends; measured subeconomic resources are negligible. Exploration by industry, 1992, was small-scale (on 2 skarn trends and 1 auriferous fault zone).

Jan 1, 1993

By Michael J. Klishis

West Virginia University researchers examined risk and exposure in the roof bolter operator's job and developed approaches for preventing accidents and for evaluating system and human performances that may be appropriate as a general application to improve safety and efficiency in the industry. Using a microanalysis of accident data and underground observations, the researchers classified bolting injuries within one of four work routines: 1) drilling bolt holes; 2) bolt installation; 3) machine tramming, (re)positioning and setting the ATRS; and 4) general face preparation. Time and motion studies were then combined with injury data analysis to develop risk and severity indices, as well as a severity-weighted index that served to determine the degree of risk and exposure by work routine. More than two dozen bolting-related problems were identified as potential situations that could lead to injuries or expose workers during their job. Approaches to avoid these situations were suggested and then applied at six mining operations to evaluate specific problems in roof bolting operations. These suggestions encompassed the three E's of Safety (Engineering, Education, and Enforcement) and emphasized the analysis of worker behaviors that lead to human error accidents.

Jan 1, 1993

The mineral Industry, following the economy as a whole, experienced little growth in 1992. However, with modernized plants, efficient workforces, and lower operating costs, the industry is well positioned to take advantage of possible improvement in the national economy during 1993. In addition to the significant 1992 events highlighted below, important events, trends, and issues within individual mineral industries are addressed in the commodity sections that follow. The value of processed materials of mineral origin is estimated to have been about $310 billion in 1992. The value of U.S. raw nonfuel minerals production in 1992 is estimated at approximately $32 billion, a 3% increase over 1991. The value of domestic minerals production has increased in all but 4 of the last 32 years.

Jan 1, 1993

By Brian T. Brady

The year 1991 recorded unprecedented change throughout the world; war in the Middle East, economic recession in key industrial nations, upheaval in Eastern Europe, and the disintegration of the former U.S.S.R. These issues and growing environmental concerns will affect the entire world mining industry. Environmental issues continue to have an ever greater effect on industrial minerals. In the United States, major issues involving the Clean Air Act, Clean Water Act, and the recent Stormwater Rule by the U.S. Environmental Protection Agency (EPA) affect many types of mineral operations. Significant developments include an important decision in 1991 by a Federal Appellate Court to overturn EPA's asbestos ban on certain products, partly on environmental grounds, and proposed legislation that would overhaul or abandon the 1872 Mining Act. On a global scale, prominent issues include environmental concerns over mining in the Antarctic and Arctic regions and a cutback in plans to clean up the Kola Peninsula in the Commonwealth of Independent States (C.I.S.).

Jan 1, 1993

By George A. Morgan

The production and processing of crude petroleum and natural gas are the dominant economic sectors of the Middle East. Downstream processing of these mineral fuels to petrochemicals and fertilizers is a major investment opportunity. In 1991, the 15 countries that constituted the region accounted for 26 % of world crude petroleum output, 15.3 % of world natural gas plant liquid production, and 4.5 % of world dry natural gas production. Only Cyprus and Lebanon were not crude petroleum producers. Production of these mineral fuels all declined from that of 1990 owing to the Persian Gulf War, during which output from Kuwait and Iraq either ceased owing to war damage, or was embargoed. Prior to the war, Iraq and Kuwait were the fourth and fifth largest world producers of crude petroleum, respectively. In the war, virtually all of Kuwait's production and transport facilities were destroyed or damaged. Iraq's output was embargoed from export, with only domestic sales taking place. The embargo also affected Jordan, both in terms of transshipment of materials through it to Iraq and in exports of phosphate and potash. Shipments of crude petroleum by pipeline from Iraq through Saudi Arabia and Turkey and by vessel through the Persian Gulf were terminated. However, the loss in production from Iraq and Kuwait was made up by accelerated output from other Middle East and world producers. Saudi Arabia, in particular, with its excess production capacity, accounted for the largest portion, increasing crude petroleum output by 27 % to almost 3 billion barrels.

Jan 1, 1993

By F. W. Wellmer

"I would like to comment on the classification scheme of ore reserves based on geestatistical and economic parameters as proposed by Wober and Morgan in the CIM Bulletin, January 1993.In principle, a classification system that combines quantitative data for levels of confidence and errors with economic expectations must be welcomed. I would like to point out, however, two aspects of the proposed classification system which might create ambiguities, and therefore problems, by working with two levels of confidence and two kinds of block sizes. A normal classification scheme reflects the information density, the highest reserve category such as class A, or proven, or measured reserves having the highest density. This is not necessarily the case in the scheme of Wober and Morgan (1993), unless the definitions are amended.I. Assuming, as the authors do, that the estimation errors show an approximately normal clistribution, at the 95% confidence level, the standard deviation has to be multiplied by about 2 for the error and, at the 84% confidence level by about 104. Reserves (or resources) with the same or even higher information density than class A reserves, which at the 95% confidence level would not fulfill the required economic criteria at the threshold level, i.e. not qualify as ""ore"" at all, could be retained ""on paper"" to class B reserves by just multiplying the standard deviation by the factor 104 instead of 2, thereby narrowing the error.This statistical ambiguity was partly inherent in the old German classification scheme which used varying confidence levels and errors (GDMB 1956; Jahns 1959). In the new German scheme, which was later adopted in Austria in a moclified version, the level of confidence was therefore fixed at 90070 for all reserve categories (Wellmer 1983; ONORM 1989)."

Jan 1, 1993

By S. Todd Mickleborough

The geostatistical technique of conditional simulation is applied to measure the uncertainty in factor of safety predictions for soil slopes where there is incomplete knowledge of the spatial distribution of soil properties. A case study considers a natural clay slope in Canada. The sequential indicator simulation technique is used as a means for generating a series of spatial maps of soil properties for this site. These maps approximate random draws from the conditional probability density function that characterizes existing uncertainty in the spatial distribution. Factor of safety determinations are then made for each simulated map using the simplified-Janbu approach, where the computations are performed with a new computer program that can operate on irregular spatial profiles of soil properties specified on a discrete grid. A unique capability of this approach is the ability to generate the distribution of factor of safety conditional to the type, position, and value of existing site characterization measurements. This capability should reduce uncertainty in FS predictions.

Jan 1, 1993

By Michel C. Frippel

This section of the Minerals Yearbook reviews the minerals industries of 27 countries: the 12 nations of the European Community (Belgium, Dermark/Greenland, France, Germany, Greece, Ireland, Italy, Luxembourg, the Netherlands, Portugal, Spain, and the United Kingdom); 6 of the 7 nations of the European Free Trade Association (Austria, Finland, Iceland, Norway, Switzerland, and Sweden); Malta; the 8 Eastern European economies in transition (Albania, Bulgaria, Czechoslovakia, Hungary, Poland, Romania, and Yugoslavia); and the U.S.S.R. Western Europe Western Europe [loosely defined to include the 12 nations of the European Community (EC) and the 7 nations of the European Free Trade Association (EFTA)] is the single largest trading area and consumer of raw materials in the world. If Western Europe was at one time an important mining sector, it has now increasingly relegated the role of supplying minerals for its minerals processing industry to the more minerally endowed countries in North and South America, Africa, and Australia. In this regard, Western Europe is the most important determinant of raw materials consumption (and thus, indirectly, raw materials production). Western Europe has significant reserves of industrial minerals but has limited availability of metalliferous raw materials. It, therefore, imports significant quantities of the latter and ranks along with the United States and the U.S.S.R. in the production of refined metals. Nonetheless, there is an inherent tendency to underestimate the importance of Western Europe in the world of minerals, both as a minerals processor and raw materials buyer. The reason for this is that Western Europe is generally thought of on the basis of individual nations rather than as a whole. Viewed in this limited context, the United States, the U.S.S.R., and Japan appear to dominate the world economy. Viewed as one regional area, however, Western Europe includes the fourth (FRG), fifth (France), sixth (United Kingdom) and seventh (Italy) largest economies of the world, all bordering on one another. With the remaining 15 EC and EFTA countries, Western Europe has a land area approximately 40 % of that of the United States, exceeds the U.S. population by 50 % and has a gross domestic product about the same as that of the United States.

Jan 1, 1993

By R. D. Lindsay

Originally the focus of Deak Resources Corporation Business Plan was to establish a method for treating small gold and possibly base metal mineral deposits located in the Kirkland Lake - Noranda area of Northeastern Ontario, Northwestern Quebec at a central treatment facility. Since the establishment of this original business plan in 1988 other processing options have availed themselves for handling the base metal ores off site at a central facility which may preclude their processing at Deak.The site selected for the Deak processing plant was Kerr Addison's Virginiatown operation. At the time this property was acquired from the Receiver following Golden Shield Resources' Bankruptcy in 1989 the mill had been processing in the order of 1, 100 SDT per calendar day through one processing module; a module originally designed to process 1,500 SDT/day of a free milling gold ore. This tonnage level however had not been achieved since 1966 when an average throughput of 1481 SDT per calendar day was recorded.In order to realize Deak's overall Business Plan it would be necessary to expand the mills processing capabilities to provide:(1) A 2200 SOT per day circuit capable of processing a free milling, medium work index gold ore;(2) a 1 ,000 SDT per day flotation and/or cyanidation circuit capable of processing refractory gold bearing materials containing refractory minerals (i.e. copper) that should be removed prior to cyanidation; and possibly(3) a 1200 to 1500 SDT/day base metal circuit capable of processing the broad range of Deaks' Base Metal Property ores. If this circuit were introduced it would be completed in two tonnage phases.Further, it was recognized when operations resumed under Deak in 1990 that the existing tailings dam was suitable for, and had sufficient capacity for additional gold tailings with necessary physical modifications and changes in disposal techniques (including the construction of containment storage cells) that would allow storage for an additional 3.4 million tons of gold ore tailings approximately 1.0 million of which has been deposited since 1990. The focus of Deak's long term tailings disposal strategy is to acquire the Barber Lake Basin which is currently adjoined to our main tailings system which will provide an additional 10 million tons of storage capacity.

Jan 1, 1993