Search Documents

By J. B. Hiskey, S. Chander, B. J. Scheiner

The use of selected iron complexing agents in preventing or ameliorating acid mine drainage was investigated. The experiments were conducted in weathering columns using refuse samples from a coal cleaning plant. It was observed that the treatment with iron complexing agents significantly altered the rate of oxidation. Some of the reagents tested reduced the rate of oxidation whereas the others even enhanced it. The results showed that a commercial reagent containing oleyl imidazoline was most effective in retarding the oxidation rate. In addition, a simple treatment with this reagent substantially decreased the rate of oxidation of pyrite in a column that was generating acid at a high rate. The effect of this reagent on the surface properties of pyrite was studied by cyclic voltammetry and zeta potential measurements. The decrease in the rate of oxidation resulted from suppression of both anodic and cathodic reactions at the surface of pyrite.

Jan 1, 1993

By Hall C. E, Chrisholm J. M

Resource calculations for shear hosted deposits of any type are difficult regardless of which calculation technique is used. One of the main problems is the determination of the geometry of the mineralisation. Once this has been elucidated then the appropriate resource calculation methodology can be employed with a search distance and orientation that is relevant.

Jan 1, 1993

By Rajendra K. Devala, Sukumar Bandopadhyay

In order to be able to design an adequate mine ventilation system it is necessary to understand how pollutant masses disperse into turbulent ventilation air streams. The mixing of gases and dusts with ventilating air, and dispersion of these pollutants in mine airways, are important flow or transfer problems. For the solution of such problems, the finite difference technique is often used. In this paper, numerical approximation schemes for the solution of the mass transfer problem have been developed using several explicit finite difference schemes. Results from these schemes have been compared with the analytical solution for spatial and time increments using the concept of Root Mean Square error. The comparison of various schemes reveals that the explicit finite difference schemes analyzed here give more accurate results at lower velocities, though the results are dependent on the spatial and time steps considered. At higher velocities the schemes tends to oscillate about the analytical solution. INTRODUCTION In mining, most of the mine air pollutants, such as respirable dust, methane, blasting fumes and diesel exhaust, are produced at the mine face and in haulageways. Injection of any of these pollutants in the mine ventilating air causes disturbances of the equilibrium state of the pollutant concentration of the ventilating air. The mixing of these gases and dusts with the ventilating air are typical examples of mass transfer processes. Pollutants are diluted by the stream of ventilating air flow along airways and discharged into the outside atmosphere of the mine through a return shaft. The dispersions of these pollutants in mine airways are important flow or transfer problems. Knowledge about pollutant sources, emission and transport of these pollutants are essential for ventilation planning and design to ensure good engineering control over air quality, quantity, and environmental conditions. Modeling of mass transfer phenomena in mine ventilation is largely based on extensive studies of turbulent dispersion in wind tunnels and the lower atmosphere of the earth. The general approach in the formulation of models lies in the recognition that these mass transfer phenomena can be conceptualized as a flow problem that can be solved by the general application of Taylor's theory (1954) of turbulent flow and diffusion with modification appropriate static and dynamic parameters. If the face zone is initially contaminated by a pollutant over a long section (e.g. instantaneous exposure of large gas accumulation, rapid methane release etc.), the process of decontaminating the mine workings can be regarded as displacement and diffusion of the tailing edge of the cloud of contaminates in the form of a semi-infinite gas body, for which a one-dimensional mass transfer equation is represented by: [at + u • ax = Ex ex2 + f (x,t)(1.1)] In Eq. (1.1), the term [~~] is the rate of growth of the concentration in the differential element, while a [(5xx )] is the net gain of material due to convective transfer. The two terms balance the total loss of material due to turbulent dispersion that is represented by [Ex . 21] and f(x,t), the source term for the pollutant in the roadway. Several cases of mass transfer that occur in mining can be identified and modelled using the conservative volume element method. The governing equation, along with the associated boundary and initial conditions, source terms and their solutions are detailed elsewhere (Bandopadhyay and Ramani, 1988, Devala, 1989). Only one mass transfer situation is presented (Figure 1) here for the present analysis. Mixed Evolution of Pollutant (multiple pulses) Typical examples of these situations are emission of pollutants from multiple diesel vehicles in the face area, and gas emission from standing pillars as well as from broken coal seam during coal cutting with a continuous miner. The mathematical statement of the problem along with the initial and boundary conditions are given below, Governing Equation: [do+u- =E d2c(1.2) ataxx dx2] Initial conditions:

Jan 1, 1993

By H. Soto, J. Jara, F. Nava, J. B. Hiskey, B. J. Scheiner

Laboratory tests showed that ozone can destroy free cyanide and weakly complexed cyanide (copper and zinc cyanides). The iron cyanide complexes were resilient to ozonation but they were effectively eliminated by precipitation with Fe (II) ions under controlled pH conditions. Tests carried out with effluents from a number of gold mills confirmed the results obtained previously in the laboratory. The industrial samples contained cyanide in the form of free cyanide and also complex copper, zinc and iron cyanides. Solutions that contained up to 184 mg/L total cyanide, after the ozone treatment analyzed only 2-3 mg/L dissociable cyanide and 50-90 mg/L CN(t) (accounted for by iron complexes). After precipitation with ferrous ions total cyanide was reduced below 1.5 mg/L. For most solutions ozone consumption ranges from 3 to 6 g per g of cyanide destroyed. However, certain impurities (such as SCN and S203 ), present in some effluents, increase ozone consumption and make it more difficult to reduce copper concentration to satisfactory levels.

Jan 1, 1993

A review of all major TBM projects from 1974 to 1990 has been undertaken and the results entered into a database. A similar database was prepared from information obtained from a principal TBM manufacturer covering the period 1952 to 1990. The database includes information such as machine specifications, machine performance data, tunnel specifications and ground characteristics. The database can be used as a guide to gauge potential machine performance in a range of ground conditions and tunnel geometries. The review also indicates that current TBM technology is limited to certain ground strength conditions.

Jan 1, 1993

By McQueen LB

The Water Board has been involved in the development and ipgrading of sewerage facilities in the Blue Mountains since 1980. In 1984 the Board prepared a report that dealt with the Blue Mountains Sewage Effluent Management study. Successive 3ovemments have been concerned about development in the 3lue Mountains and the effect this development is having on the luality of the streams flowing into the Blue Mountains National ?ark (presently up for World Heritage Listing).

Jan 1, 1993

By A. P. Cook

Methane drainage on a mine-wide scale is a relatively new technology to South African coal mines. Shallow seams and apparently low methane contents have been assumed to result in less methane problems than experienced in other countries. The introduction of deeper mines however, has now resulted in methane drainage taking on a higher priority. Methane contents in the region of 12 m3\t have resulted in one colliery introducing drainage as a ventilation support. Although a low seam permeability initially indicated reduced potential for drainage, early borehole flows of 90 m3\m\year have since increased to 450 m3\m\year. Rapid inflow of methane into goafs and sealed areas from seams surrounding the main production seam at another colliery have warranted extensive evaluation of the methane properties of these seams with the projected introduction of predrainage from surface. Methane pressures in excess of 1000 kPa and contents in the region of 10 m3\t again give methane volumes suitable for drainage. Coal seam drainage ahead of mining is becoming more significant and is likely to see an increase in the near future. INTRODUCTION Methane gas is an everpresent hazard associated with underground coal mining. Safe working levels of methane in the mine atmosphere are normally maintained by ventilation practises, ensuring sufficient dilution of the gas. However in some cases the ventilation must be assisted by methane drainage, either from the mined seam, or from adjacent seams and strata, or from goafed areas. South African collieries have practised only limited methane drainage until now. Relatively shallow mining depths, and apparently low in-seam methane contents have been assumed to result in fewer problems with methane than are the normal for other countries. This is now being shown to not necessarily be the situation. Work carried out by the Coal Mining division of COMRO (Cook and Erwee, 1991) indicates South African production coal seams have very similar methane retention properties to those of coals in other countries, with seam gas contents of up to 12 m3/t. This awareness, as well as greater mining depths, and higher degrees of mechanisation, has resulted in higher priority being given to methane emission problems throughout the industry. Increased levels of safety, as well as possible commercial applications, are the main reasons for the interest now being shown in methane drainage. Not only is there possible applications in the present production coalfields, but South Africa has vast areas of coal reserves which are presently non-mineable, now being seen as possible alternative energy sources. Limited methane drainage is practised within the industry, but only on collieries that have identified specific methane problems that can be alleviated by drainage. Historically this has been restricted to surface drainage of longwall goafs, reducing emissions onto the faces. More recently, horizontal in-seam holes have been drilled, until now for bord and pillar sections, but the results are being evaluated for later application to shortwall faces. Adjacent seams pose problems at some sites and vertical and cross measure boreholes are now being considered.

Jan 1, 1993

By Ehlert G, Steinlechner E

The paper describes a new process for filtration which combines the continuous operation of conventional vacuum filters with the low final moisture contents hitherto only achievable with plate and frame presses. The increasingly high portion of fine particles causes several problems in the filtration of copper concentrates. One drawback is that remarkable quantities of liquid are attached to the very fine particles because of their specific surface area. Furthermore, fine particles also reduce the size of the capillaries in the filter cake, thus increasing the critical pressure which any filtration system has to exceed to achieve the desired final cake moisture. The maximum filtration pressure of conventional vacuum filters is limited by nature itself and by practical aspects to approximately 0.75 bar. The hyperbaric filter combines the continuous operating principle with an increase in filtration pressure of up to 6 bar simply by placing the entire disc or drum filter inside a pressure vessel. The major machine components and process features are explained in the details of the paper. After extensive research and field testing, 23 ANDRITZ hyperbaric filters, with a total filtration area of 1968 m2 have now been sold. Seventeen of these units (1440 m2) are in commercial use and more units are, on order. Performance data on copper concentrates from plants in Australia, South America, Poland, Africa and North America are outlined in detail. Compared to vacuum filters, generally hyperbaric filters will reduce the final cake moisture of concentrates with 75 per cent

Jan 1, 1993

By Laajalehto K

The basic condition necessary for flotation is hydrophobicity of the surface of the mineral to be floated. For sulphides, this condition usually requires treatment with a collector solution. The conditions for this treatment have until recently usually been chosen by the trial and error principle which has indeed been working relatively well under favourable conditions; ie for simple homogeneous ores. However, the present tendency to increasing use of complex and often relatively lean ores sets increasing requirements for the control of the flotation process. This development is the reason for the present rapid development of process control methods in flotation. In addition to the already well-established practices of pH and reagent feed controls, the importance of measuring and controlling the electrochemical potential of the ore particles to be floated is recognised in the case of sufficiently conductive minerals. In fact, the electrochemical potential seems to be the basic quantity determining the flotation behaviour of such relatively well-conducting minerals as sulphides. Since the hydrophobicity of the mineral and, hence, its flotation properties are ultimately determined by the composition and structure of its surface, information on these under different process conditions is important for design and operation of efficient flotation processes. The basic requirement set for the methods used for obtaining this information is high surface sensitivity of the method. The recent rapid development of surface characterisation has produced several methods which fulfil this requirement. Their application to the problem of characterising surfaces of mineral samples in contact with collector solution is, however, often complicated. The main reason for this is the vacuum environment necessary for the measurement. In the case of flotation experiments this means that in most of these methods the measurement cannot be made in situ, but the sample must be extracted from the liquid and subsequently evacuated in the vacuum chamber of the instrument. It is essential to carry out these steps so as to avoid to the extent possible changes in the sample surface. For the purpose of establishing whether this has been accomplished it is important to compare the results of methods operating in vacuum with some available in situ method. An optimal choice of methods seems therefore to be a combination of the available powerful vacuum methods with in situ measurements. The most usual combination seems to be X-ray photoelectron spectroscopy (XPS or ESCA), Fourier transform infrared spectroscopy (FTIR) and electrochemical measurements. This choice combines the unique possibilities for direct elemental and chemical characterisation offered by XPS (Cecile, 1985) with the in situ capability of FTIR and electrochemistry. In the XPS measurements, it is essential to apply a special sample handling technique to avoid loss or damage of some sensitive species of the collector-based layer on the mineral surface. In the following will be given some examples of the application of the XPS technique in combination with electrochemical methods of sample treatment to studies of the layer formed on sulphide substrates in ethyl xanthate (EX)

Jan 1, 1993

By Y. K. Rao

In the carbonyl process for the refining of crude nickel CO(g) reacts with nickel in the 310-370K range producing nickel tetracarbonyl, Ni(C0)4(g). Iron and cobalt impurities also form gaseous carbonyls but their partial pressures are low. The carbonyl is led to a decomposer plant wherein the gas disproportionates in the 500-600K range depositing pure metal on nickel pellets that move countercurrent to the gas-flow. This system serves to illustrate the fundamental principles involved in the vapor phase mass transport of elements, against temperature-gradient, under the influence of chemical potential gradient. Unlike in the crystal growth, the source is at a lower temperature (say 350K) whereas the seed is in the hot-zone (say 550K) of the closed ampoule-type reactor. By assuming virtual gas-solid equilibria in the end zones, with diffusion of gaseous species between them acting as a slight perturbation, the quasi-steady- state mass-transport rates are computed for a range of CO-pressures and temperatures.

Jan 1, 1993

By Rogers M, Sullivan B

Golden Crown Mine is a narrow vein gold mine producing 75000 tpa. Production has been predominantly by shrink stoping using hand held machine and airleg. Bogging from these stopes is done with Toro 150 LHD units.Previously the standard development method consisted of developing a sill drive, a footwall drive and millholes every 7 m. This meant that for every metre of ore development, 2 m of waste development was required.

Jan 1, 1993

By A. D. MacPhail

The Highland Valley Copper partnership was formed in July 1986 and was the logical result of a mine with a large ore reserve but no adequate mill, and a mine with a large, modem mill but dwindling ore reserves. The original partners -Cominco and Lornex -were joined in January 1988 by Highmont Mining Co. which contributed a two-line concentrator. During 1988/1989, the Highmont mill was moved 7.5 km to adjoin the Lornex mill, forming what is now called the Highland mill, with a current nominal capacity of 130 000 tonnes per day. The mine is located 220 km northeast of Vancouver, British Columbia and is close to four communities in which personnel make their home: Logan Lake, Merritt, Ashcroft, and Kamloops. The map in Figure 1 2.2 shows the general area. Kamloops is a major service centre and is serviced by two railways, two major roads and a regional airport.

Jan 1, 1993

As noted by D.W. Fuerstenau in his Plenary Lecture at the Conference on Extractive Metallurgy of Gold and Base Metals, Kalgoorlie, Australia, "Com¬minution of solids is surely one of the oldest technologies that, even in this day and age of DNAs, chips and space exploration, continues to challenge our scientific acumen and engineering ingenuity." Thus, the fundamentals of comminution continue to receive a great deal of attention in the literature. This was particularly true in 1992 with the publication of the proceedings from the SME-sponsored symposium, Comminution Theory and Practice. Papers covering topics ranging from liberation to comminution fundamentals to novel size reduction techniques are included in this review. Liberation Liberation continued to be a prime area of research interest, not only in terms of liberation modeling, but also in understanding the basic mechanisms involved in mineral liberation. King (Comminution - Theory and Practice, pp. 3-15) described a method for determining the interphase area between mineral grains. He showed how the mea¬surement of interphase area before and after comminution could be used to determine the presence or absence of intergranular fracture. Lin, Miller and Cortes (Kona, Vol. 7) discussed the use of computed tomography (CT) as a nondestructive means of investigating three-dimensional particle composition. The use of this technique in constructing coal washability curves from CT data was presented.

Jan 1, 1993

By L. D. Johnson

12 groups of 12 precast prestressed (PCPS) piles were driven in the lagoon of Kwajalein Island to support a dry dock. Pre-construction investigation of the calcareous coral sands and static pile loeid tests were performed to determine if the 7.9 by 7.9 cm (20 by 20 inches) by 26 m (85 ft) long PCPS piles embedded to a depth of 16 m (53 ft) would adequately support the dry dock. Driving records for production piles indicated that the blowcounts of the piles at the fincil embedment depth became substantially less than expected as piles wssre driven further toward the lagoon end of the dry dock and decreased to as low as 2 blows/ft. A supplemental investigation that included a static load test on a production pile, the driving of an indicator pile, and restrikes indicated that the pile foundation has adequate bearing capacity. The observed bearing capacity appears to be effected by several mechanisms including breakdown of cementation between sand particles, densification of the sands during driving, and dissipation of excess pore pressures and recementation after driving.

Jan 1, 1993

By Kubo H, Ninomiya R, Ojiro T, Sato T

New high-strength Zn alloys for moulds are demanded from the automobile and electric industries in Japan, because the s rength of Zn moulds is still not high enough for the mass production. There are two approaches to improve the strength of Zn alloys. One is to increase the Al content. ZA alloys (ZA-8, ZA-12, ZA-27) were developed through this approach. The other is to increase the Cu content. But it is known that an increase in Cu generally depresses the castability of Zn alloys, so that the alloys with increased Cu have been rarely studied until now. In this study a reconciliation between the strengthening and the castability of Zn alloys by enriching both with Al and Cu has been attempted. Accordingly we have studied on the Zn alloys containing 4 to 25 mass per cent Al and to 24 mass per cent Cu have been studied. Their fluidity, which primarily corresponds to the castability of the alloy, were measured first and 19 alloys were selected based upon their fluidities and casting temperatures. Mainly the mechanical properties of all 19 alloys were tested and some were found to be excellent in both strength and castability. Z1009 (Zn-IOAI-9Cu-0.02Mg alloy) cast in a sand mould has the tensile strength of 360 MPa while ZAS (Zn-4AI-3Cu-0.04Mg alloy), which is the most popular alloy for moulds, is 215 MPa. Z2520 (Zn-25AI-20Cu-0.02Mg alloy) cast in a sand mould has a Vickers hardness of 178, compared to 107 for ZAS and 104 for ZA-27 (Zn-27AI-2Cu-0.02Mg). Furthermore the castability of Z1009 is as good as that of ZAS. The underside shrinkage occuring in casting ZA-27 is restrained in Z2520.

Jan 1, 1993

By H. T. Mulryan

Talc is used as an essential ingredient in a wide variety of plastics applications ranging from polyester body patch compounds through polypropylene automotive, appliance, and household furniture components to high performance parts made from liquid crystal engineering resins. The paper focuses on polyolefin applications; the three tier market for talc in polypropylene; the effects of various talcs in typical compounds; and trends in each market segment. Emphasis is given to emerging markets, examples of which are polypropylene compounds which mimic higher cost resins, and polyethylene films, customer requirements for talcs for these purposes are discussed.

Jan 1, 1993

It is extraordinary that while Australia depends heavily on mineral wealth for its economic well-being, most Australians have no appreciation of the traditions and principles which drive and govern the mineral industry. Their understanding has been largely provided by those who campaign against the industry in one way or another and is therefore quite unrepresentative.

Jan 1, 1993

A universal grinding circuit model suitable for an arbitrary structure of flowsheet has been suggested. In this model classifiers and mills are described in a most general form. What puts the model in a class by itself is the automatic mass balancing in all streams of the circuit. In order to provide this a special classifier model is adopted. A previously published continuous steady state process model is used as a grinding model. Non-linearity of classifier model leads to a resultant circuit model which is equivalent to a non-linear integral equation. It complicates somewhat calculation algorithm in comparison to that of linear model, but provides a physically meaningful solution.

Jan 1, 1993

In May 1993, SME contracted with The Dolecek Companies of Denver, CO to conduct a salary survey and a study of Mining Engineering. A written, four-page survey was sent to a random select sample of 1897 current SME members from the United States and Puerto Rico and to 40 current SME members from Canada. A total of 621 survey responses were input and analyzed, to guarantee the validity of the survey findings. The findings are representative of the entire SME membership. And the survey is within a statistical range of accuracy of plus or minus 5%. Salary survey SME members currently earn an average of approximately $60,000 a year. Some 45% earn less than $60,000 and 49% earn more than that. About 24% of all SME members earn $80,000 or more each year and 13% earn $100,000 or more. Not surprisingly, a statistically greater number of owners (27.5%) and those in senior management (30%) have a current income or salary of $100,000+ a year.

Jan 1, 1993

By Alan T. Nelson, Ronald D. Mariani

The Tilden concentrator was originally constructed in 1974 for the processing of low grade hematite. Flotation is a key concentrating process in the operation, and therefore flotation optimization has been a major concern since the plant startup. This paper will discuss some of the modifications made in the process to achieve optimization. The conversion that now enables the plant to process magnetite as well as hematite also will be discussed. INTRODUCTION The Tilden Mine, located in Ishpeming, Michigan, is managed by Cleveland-Cliffs Iron Company and is owned by Cleveland-Cliffs and two Canadian steel makers. It was constructed and started production in 1974 and expanded in 1979 for processing a low grade, fine-grained hematite iron formation for which there was previously no technology available. Several papers have been written describing the unique character of the concentrating operation. The hematite plant consists of 12 grinding and concentrating lines, which utilize two stages of autogenous grinding with crushing of an intermediate sized product. The ground product is deslimed in a highly dispersed alkaline environment to reject silica. Corn starch, the flocculant, has a high affinity for iron at the operating pH range of 10.5 to 11.0. The ore is upgraded from 35% to 45% iron in the desliming step. The deslime thickener underflow is the feed to flotation. Each flotation line consists of a bank of 10 rougher cells, followed by four scavenging banks incorporating 5, 4, 3, and 3 cells each. The Wemco flotation cells are each 14.1 cubic meters (500 cubic feet) in volume. A total of 12 flotation lines are available. [ ] A reverse flotation process is employed, using a straight-chain, 8 to 10 carbon primary ether amine silica collector. At the levels used in the circuit, the amine also serves as a frother. A final concentrate is produced in the rougher cells. The concentrates from the four scavenging steps are combined and recirculated to the feed end of the roughers, with the fourth scavenger froth being discarded as a final tailing. Upgrading to about 65% iron is achieved, with control of the circuit based on final concentrate silica grade. Starch is again used, this time as a depressant for iron. During the years of operation, several key areas of the flotation process have been targeted for optimization. The most significant improvements have been realized in the following areas: *Grade Control Automation *Control of Water System Chemistry *Flotation Spray Water This paper will focus on these areas, but other minor improvements also will be briefly discussed.

Jan 1, 1993