Search Documents

By Darryl Amick, Keith A. Prisbrey, Lee E. Plansky

The problem addressed was to develop automated image analysis of metal welds to replace unreliable and costly 100% visual inspection. The objective was to evaluate neural networks combined with features from gray level surfaces. Photomicrographs of the welded seam in Zircaloy-4 channels used in nuclear fuel rod assemblies were examined. The methodology used was to select a set of morphological feature coefficients from Bessel Fourier morphological feature coefficients extracted from digitized photomicrographs. The selected morphological feature coefficients were then used to train a neural network. The approach was verified initially by successfully training a neural network using the known, secondary chemistry of the alloy welds. The results were good. The Bessel Fourier coefficients captured sufficient information from the metallographic images to distinguish weld quality. This approach has the combined advantages of compressing the images through Bessel Fourier coefficients and give the ability to rapidly process large amounts of data using neural networks.

Jan 1, 1993

By X. Cheng

The mechanism of cathodic decomposition of pyrrhotite was studied in deoxygenated solutions at natural, near neutral pH using potential and cyclic voltammetric measurements. Reaction products on pyrrhotite surfaces were examined by AES and XPS, and by analyzing the voltammograms for the electron balance of the reactions. Surface properties of the pyrrhotite/solution interface were characterized using ac impedance technique. The parameters of an equivalent circuit were determined by the nonlinear least squares fit (NLLSF) technique. The effect of cathodic polarization on floatability was investigated by micro-flotation tests. Possible implications to the flotation separation of chalcopyrite-pyrrhotite ores are discussed.

Jan 1, 1993

By Takeshi Tanaka, Yasuhiro Komamura, Yuusaku Tominaga, Takayoshi Iwamoto

In order to assist better countermeasures for ventilation control in normal/abnormal condition of mine ventilation network in real time, branch relation table derived from a macroscopic characteristic of ventilation network is introduced in this study. The main results in this study are as follows; 1) One of macro characteristics of a ventilation network, as a relation between airflow rates in two branches chosen arbitrarily, is specified under the change of aerodynamic resistances in a branch. Airflow rate in a branch can be estimated by airflow rate in other branch changing aerodynamic resistance by using empirical formula. The empirical formula by computer simulation of the Horonai coal mine, Japan is considered to be a one-valued function with monotone or extremums. 2) A branch relation table shows the macro characteristics, mentioned above, of all the set of two-branch combinations in a network. Elements in the table give both information of control possibility range of airflow rate and total number of extremums in an empirical formula. 3) It is important that when aerodynamic resistance change in a branch is estimated by measuring airflow rates in two typical branches, the two branches should be chosen from branch combinations with monotonous relation in the branch relation table. 4) A flexible expert system to assist ventilation control in the specified branch in real time has been developed by using a branch relation table for a ventilation transfer diagram of the specified branch, such a coal face and an advancing face. A fuzzy reasoning is utilized in the recognition of the safety factor, methane concentration, in the system. And when conviction degree in recognition for methane concentration at the specified branch is too low, the system searches for other branch combinations in the branch relation table stored in the system, to use other ventilation transfer diagram of the specified branch. When a needed ventilation transfer diagram is not stored in the system, the expert system asks automatically the ventilation simulation from other computers linked to the main computer automatically. The system repeats consultation until conviction value of safety in the specified branch approached

Jan 1, 1993

By B. K. Mishra

Power draw of the mill has been accepted as an indicator of the performance of the mill, yet the problem of predicting power under a given set of mill operating conditions still remains to be solved. In the literature, this problem of predicting power is attributed to a lack of knowledge with regard to the motion of the charge. Here a DEM based model is used to analyze the motion of the charge. The resulting information is used to predict the power draw of the mill. A 16-ft diameter mill is simulated. A factorial design study of the variables-mill speed, lifter configuration and ball size distribution-as independent variables is taken up. The power draw as a response variable is analyzed to establish the best operating condition of the mill.

Jan 1, 1993

By James I. Mathis

Should an arbitrary reduction factor be applied to laboratory compressive strengths when designing pillars? The answer is, as is the main contention of Peng's article, probably not. Many factors affect the strength of the material remaining in the pillar. On the other hand, outside influences will influence the strength testing results from the lab. This is not the first article, nor the last, to discuss the discrepancy between the two strengths. As was discussed in the article, actual pillar strength is affected by several factors. The two mentioned were: • The scale effect of discontinuities. How large must the pillar be so that the increase in discontinuity count with size will not decrease the strength. • Non-uniform strengths and lithologic units within the pillar. The scale effect of discontinuities is important. What size block must be tested so that the rock mass strength is actually measured? For a highly fractured rock mass, or coal with a high cleat density, this sample may be quite small. Conversely, if an unaltered, moderately jointed, quartz monzonite was examined, the sample block would likely be very large. This is the subject of ongo¬ing research. More to the point, if the tested sample is sufficiently large to model the rock mass strength, then no reductions should be made in the lab strength based on this factor alone. Non-uniform strengths and variations in lithologic units will also affect the pillar strength. I am not an expert in coal mines, having gained my experience in hard rock metal mining. These problems, though, are commonplace. However, strength sampling for pillar strength determination involves sampling material from within the lithologic unit that will form the pillar, not from pieces of material found on the floor. In addition, this sampling should cover the entire range of strengths of the material in the pillar-hard units (such as the partings described by Peng), as well as soft units. Testing results should then be included in the pillar design. Contrary to statements in Peng's article, at least one rock mass rating system (Laubscher, 1990) allows for the compositing of strong and weak units into a design rock mass strength that can be used for pillar design.

Jan 1, 1993

By C. Damiani

The Chuquicamata smelter, operating since 1952, has gone through several developing stages which have been characterized by the addition of peak technology for copper concentrate smelting (Teniente converter and Outokumpu flash furnace) with an intensive use of technical oxygen, which has permit-ted to partially discontinue the reverberatory furnace utilization. This paper shows the main indicators and operational practices at present, as well as those concerning maintenance aspects. Finally, the most relevant topics related to the future development of the smelter are mentioned with special remarks on the Decontamination Plan, which allows US to keep the high level of production, reducing the emission of contaminants according to the legal requirements in force.

Jan 1, 1993

Ladies and gentlemen, it is a privilege to be able personally to welcome you to the opening of this Symposium. It is particularly pleasant to be able to extend a warm South African welcome to al our visitors from foreign shores. We trust you will enjoy your stay in our country. It is a singular honour for me to be present here today, and to have been asked to open this international Symposium. MINING IN SOUTH AFRICA Mining is the single most important contributor to this country's foreign-exchange earnings. Minerals and processed mineral products together account for about 70 per cent of South Africa's total foreign exchange earnings. The mining sector employs in excess of 670 000 people, and is one of the largest employers in the country. The construction and development of cities and towns like Johannesburg, Welkom, Orkney, Springs, Benoni, Witbank, and Klerksdorp is a direct result of the contributions of the mining industry to economic activity in these areas, as well as of the multiplier effect of secondary industries.

Jan 1, 1993

By H. Ruthert

An understanding of wear in systems conveying solids is extremely important from the standpoints of design and economics. The lifetime of any bulk solids-handling system depends on the type of solids present and the operating parameters of the transportation system. The relationship between wear in backfill pipelines on South African gold mines and the transportation system's operating parameters is well understood. However, the effect of the transported solids on the pipe wear is less well understood, because of an inability to characterize particle sharpness. The sharpness of the particles, together with their size and hardness, is responsible for the aggressivity of particles, or their ability to cause damage and wear. This paper presents a novel method for the characterization of particle sharpness. The results presented rank particles according to the sharpness of their surfaces.

Jan 1, 1993

By J. C. Yingling, G. T. Lineberry

A control system for reducing peak loads on mine conveyor networks is proposed. The system involves continuous monitoring of flows into the conveyor network and section feeders with variable discharge capability. The control strategy uses differences in material transit times from various production units to the transfer points in the network to forecast load levels that will he intersected by the discharge of the controlled feeders over future time intervals. Feeder setpoint adjustments are made to prevent excessive peaks in the combined flows at the transfer points, while maintaining adequate feeder through flow to avoid production bottlenecks. Simulation studies suggest that the control strategy would be very effective in reducing capacity requirements of gathering belts.

Jan 1, 1993

By Vaughn Bowns, Allen Stanley, Brian Redeker

"Running casing in drilling operations is often complicated by boulders or large cobbles.Past practices of dealing with these have included use of drop hammers, attempts to drillthrough or around the boulder, contact explosive charges and even pulling the casing andrepositioning the hole. All these methods are time consuming, expensive and offer noguarantee of success. In this paper a different method of dealing with these boulders ispresented that promises to be faster and less expensive with a much higher success rate.This involves using a light plastic conduit pipe to place a shaped explosive against theboulder. It requires no special tools or techniques not commonly in use in the drilling andblasting industry."

Jan 1, 1993

By L. B. Rothfeld

This paper presents preliminary results of a Bureau of Mines study of potential costs of compliance with the federal Resource Conservation and Recovery Act for copper heap and dump leaching. Specifically, estimates are given for the cost of compliance with possible technology standards that would require the use of liners and closure caps regardless of terrain and underlying geology and hydrology. This cost is compared to the co lit of compliance with present state requirements for terrain a typical of those found at existing copper leach sites in the Southwestern U.S.A. Incremental compliance costs are found to widely exceed screening criteria used by the Environmental Protection Agency to denote significant economic impact.

Jan 1, 1993

By G. S. Victorovich

Technical progress in primary smelting has changed the face of the copper industry in the years since the Second World War. Much of this change has resulted from a wide acceptance of flash smelting technology. In addition, research has been directed toward devising converting processes to replace conventional Peirce-Smith converting technology. One major thrust has involved a revival of the old " ", idea of oxygen flash converting of comminuted mattes. This paper reviews the 60-year history of flash converting. Particular attention is paid to Inco's investigations into the processing of white metal containing significant amounts of nickel and, in some cases, iron. Thermodynamic analysis and laboratory experimental results are presented which throw light on the behaviour of nickel and other salient features of flash converting. The possible role of oxygen flash converting in the copper pyrometallurgy of the future is briefly discussed vis-a-vis direct production of copper.

Jan 1, 1993

By M. A. Chandler, G. T. Adel, J. N. Richardson, E. C. Gutierrez

A rapid, bench-top analyzer has been developed to determine P2O5 content and CaO/P2O5 ratio in phosphate ores. The analyzer utilizes a portable computer equipped with a frame grabber to measure the reflective intensity (gray level) of phosphate samples placed in front of a television camera. P2O5 content is related to the average gray level of the sample, while CaO/P2O5 ratio is determined from the amount of bright material present. The sensor is currently being used to analyze flotation concentrate samples at Texasgulf's phosphate operation near Aurora, North Carolina. Sensor development along with results from laboratory and in-plant testing are discussed.

Jan 1, 1993

By Mohamad H. Hussein

A minipile system was employed in underpinning a historical structure in Florida. The existing structure is founded on shallow foundations. Subsurface conditions at the project site consist of deep organic deposits interbedded with loose sand and silty sand. A minipile foundation system was deemed the most appropriate underpinning corrective measure for the already badly cracked structure. A total of 68 minipiles, 3.5 inch OD and 0.25 inch wall thickness closed-ended concrete-filled steel pipes, were installed to depths varying from 55 to 175 feet. Installation was accomplished with a pile driving hammer having a rated energy of 1 kip-ft. Highest required pile design load was 15 kips. Conventional static and wave equation analyses were performed to establish preliminary pile lengths, to assess pile drivability and establish driving resistance criteria. Dynamic pile testing using the Pile Driving Analyzer was conducted on six of the production piles. This paper describes geotechnical design considerations, installation procedures, and dynamic field monitoring. This case represents unique applications of pile dynamic testing and such slender, very long minipiles in compressible soils.

Jan 1, 1993

By M. R. Smith

Barrick Goldstrike Inc.'s Betze/Post Open Pit is located at the north end of the Carlin Trend, in Eureka County, Nevada, U.S.A. (see location Map, Figure 1). About ten open pit gold mines exist on the trend, which strikes northwesterly, through the north end of Eureka County and into Elko County. The final Betze/Post Pit configuration is shown in Figure 2, Pit Configuration. The final pit will be about 2450m long by 1550m wide, elongate in a west-northwesterly direction. The pit straddles the Barrick/Newmont property boundary. The highest elevation of the pit perimeter is 1800m at the south wall, with the east end pit bottom elevation at 1200m.

Jan 1, 1993

By Denisov GA

Conventional processes for disintegration of ores are characterised by low selectivity and cause damage to the components of their structure. It affects their liberation and recovery which are connected also with the inevitable formation of extreme fines. In the world practice recently came into view 4 trend to grinding of materials within a thick layer (in a bed layer), which provides a substantial selectivity of liberation, for example, of kimberlite. The degree of diamond preservation in the final product is highly increased. However, this method causes a considerable overgrinding of material. A new method of intralayer vibro-impulse breaking of materials providing an easily adjusted force acting at the layer and timely removal of product size grains from the grinding chamber has been developed in Russia.

Jan 1, 1993

By Thomas M. Barczak

Wood cribs are used extensively by the mining industry to stabilize mine openings. While the cost per crib is relatively low, their extensive use can result in annual mine costs of over $1 million. In an effort to improve the utilization of these supports and to reduce ground control hazards, the U.S. Bureau of Mines has developed engineering methods to assist mine operators in wood-crib design and employment. Design and employment criteria are established based on the strength, stiffness, and stability of the crib structure in relation to the load conditions imposed by the mine environment. Models have been developed based on full-scale tests in the USBM's Mine Roof Simulator that compute the capacity of wood cribs of various configurations and material constructions as a function of displacement of the crib structure due to roof-and-floor convergence. These models permit the comparison of the loading characteristics and costs of employment of different crib designs, and in conjunction with roof behavior models, provide a means to determine the optimum design and employment strategy.

Jan 1, 1993

By K. N. Han, P. B. Queneau, Bruce W. Cavender

Measures of metallurgical performance, such as recovery rates or mass balances, are frequently based on point estimates of operating conditions in the system of interest. Because the processes being measured are dynamic, a range of uncertainty accompanies each measurement; this uncertainty is reflected in the accuracy with which the calculated result describes the true metallurgical performance. In stochastic modeling, a range of probable values is used in place of a point estimate to describe each variable. The calculated result takes the form of a distribution, delineating both the magnitude and probability of potential outcomes.

Jan 1, 1993

By Deepak Malhotra

The first step in the development of a gold deposit is the detailed mineralogical examination of the ore types, major and minor mineral constituents and their association. It is extremely difficult and expensive mineralogically to characterize the occurrence and association of gold with other minerals for low-grade refractory ores (less than 0.1 troy oz/t Au). Even if a mineralogist can identify a gold-associated particle or two, one wonders how representative they are of the deposit. What alterative does a metallurgist have for characterization of gold-bearing ores? Diagnostic leach procedures, consisting of a series of sequential leaches, can provide the metallurgist/mineralogist with reasonably good Indication of the deportation of gold in the various mineral matrices. This information con help the metallurgist concentrate on the most promising process options In the Initial stages of the project development process.

Jan 1, 1993

By Lorenzen L

In South Africa, as in many other countries, the young engineering graduate is promoted quite soon to a management position where he uses less technical skills and more people-oriented skills. In the standard undergraduate curriculum for engineering, little attention is paid to the non-technical issues of the profession. An undergraduate course in management techniques cannot be a substitute for a MBA or Masters degree in engineering management, but can at least create an awareness of the practical problems facing the engineering manager. The aim of this paper is to provide an outline of such a course structure at the University of Stellenbosch. A survey is also presented on management training in the South African and Australian mineral industries. Feedback from students and graduates indicates that the fresh graduate does not fully appreciate the value of such a course until he/she achieves a position of responsibility after two or three years. Nevertheless, the management course appears to be successful in widening the perspectives of the engineer. As explained frequently in management journals, the technically oriented person (the engineer) has a convergent thought pattern, which could be in conflict with the more divergent thought pattern of the top, personnel or marketing manager. It becomes increasingly imperative for the young minerals engineer to be externally oriented instead of the traditional internal focus of engineering. The engineer should not only be aware of environmental issues in the technical design and operation of plants, but should also understand the inter-relationship between public relations, political pressures and environmental perceptions vis-d-vis technical facts.

Jan 1, 1993