Search Documents

By P. A. Botha

The production of iron and steel generates various types of waste materials containing oxides, carbon, and flux material. Usually, these materials are land-filled at the plant site or are hauled away for disposal. Some of these waste materials are hazardous, and they must therefore be recycled or disposed of properly. The influence of different waste materials in iron-ore sinter blends on the quality and operational parameters in sinter production is described. The recycling of waste materials such as dolochar, scrap fines, mill scale, electric-arc furnace slag, basic-oxygen-furnace mud via the sintering process can achieve a saving in the cost of the raw materials (for example, fuels and flux) and a reduction in pollution. A comparison of a typical sinter with a sinter produced through the utilization of waste materials shows a distinct correlation between certain types of waste material and some metallurgical properties and operational parameters. Dolochar (and arc-furnace slag) in a sinter blend acts as part of the fuel and flux that are normally added to a sinter mix. In general, dolochar improves the quality of the sinter and decreases the consumption of coke. Other waste materials adversely influence the quality of the sinter, but not necessarily the operational parameters such as the production rate. At Vanderbijlpark, approximately 15 kt of various waste materials per month are successfully recycled in the sinter plant. Investigations into the handling and recycling of other waste materials may indicate that even more waste materials can be utilized.

Jan 1, 1993

This paper outlines a range of strategies for steady state optimisation of most types of concentrators. Optimisation is considered in terms of comminution performance, energy efficiency, concentrator strategy and overall mine/concentrator operating philosophies. Application becomes more complex as the range of optimisation is expanded. However, the potential gains also increase. A step by step framework for data collection and analysis is provided. This process is facilitated by powerful simulation and mass balancing programs which are now in common use. Once a sound, steady state rationale for optimisation has been developed, it may be used to provide a fine foundation for process control system development.

Jan 1, 1993

By Koppe J. C

This paper describes the methodology developed to establish a sequentia mining plan applied to a coal mine, using computers. Firstly, isocontou. maps were generated from the drill holes and outcrop description information, representing the thickness and depth of the rock formation: present in the mine site. The procedure relies on the repeated application of the cross validation techniques, until the standard deviation of thi estimation is reduced to a minimum.From this map the coal reserves of the two coal seams, the overburdet (separated in hard and soft material) and the interburden were calculated After that, the maps were transferred in digital files to AutoCAI software, where different mining plan simulations were performed. 7b ore evaluation in each case was done automatically, including tonnages volumes and stripping relations. The final mine configuration consider the economic aspects of the operation.

Jan 1, 1993

By J. Hanna, J. Jung

Researchers at The University of Alabama have recently developed a two-step method for the treatment of phosphorus sludge. The process includes the bulk removal of phosphorus by physical separation techniques followed by the remediation of the residual P4 in the sludge using a novel, wet, air-oxidation technique known as "HSAD." Tests made on electric furnace, phosphorus sludge samples have demonstrated that an essentially complete and fast removal of the contained P4 can be achieved by the HSAD wet oxidation treatment. Further studies were made to determine the applicability of the two-step process to sludges of different origins, pretreatments, storage conditions and P4 contents. The present work discusses the mechanisms and factors controlling the HSAD, wet, air-oxidation remediation approach.

Jan 1, 1993

By Tom Hanke, Joe Strobbe

The 80 year old Theodore Roosevelt Dam built in a scenic canyon near Globe, Arizona is currently undergoing a major renovation. The old stone dam, built by hundreds of skilled stonemasons, is being covered with a new concrete face that will increase the dam height by 77 feet. The renovated dam will improve flood control and provide increased electrical power and recreation area. The contractor, J.A. Jones is constructing the new dam and powerhouse for the Bureau of Reclamation.

Jan 1, 1993

By Vincent Thorne

On January 2, 1992, the R. Zoppo Company of Stoughton, Massachusetts started drilling and blasting operations on U.S. Army Corps of Engineers Project Number: DACW33-91-B-0072 to widen and deepen the Portsmouth Harbor and Piscataqua River Navigation Channel.

Jan 1, 1993

By Karl E. Burgher

Accidental explosions occur throughout the world. They can happen at chemical plants, fireworks plants, grain depots, or as a result of collisions involving volatile or hazardous chemicals. It is interesting, as we know as blasters, that we can take two very harmless products and mix them under certain conditions and produce a violent explosion. It is often very difficult for the investigator to determine the magnitudes of blasts after the fact. However, an estimate must be made to settle vibration and airblast damage claims. The blasting consultant or technical representative is often called upon to act as an expert to mitigate these claims.

Jan 1, 1993

Using a Mark IV surface force apparatus, adsorption of dodecylamine hydrochloride on mica has been studied at pH 5.7 in the presence and absence of octanol. With amine alone, the repulsive forces between mica surfaces are reduced due to charge neutralization and attractive hydrophobic force; however, the latter is of relatively short-range with its decay length less than 2 nm. In the presence of amine and octanol, the hydrophobic force becomes more significant, its decay length being extended up to 6.5 nm. The increased hydrophobicity in the presence of octanol is attributed to the co-adsorption of the neutral surfactant with dodecylamine, which increases the packing density of hydrocarbons on the mica surface. The increased hydrophobicity due to co-adsorption is reflected in the improved floatability of silica when using octanol as an extender.

Jan 1, 1993

By Meloy TP

Several important, fundamental aspects of the grinding behaviour of mineral systems are addressed. The Levenberg-Marquardt algorithm for systems of constrained non-linear equations was used to solve the steady-state and dynamic population balance model (PBM) grinding equations to obtain the mill matrices and grinding selection and breakage rate functions, respectively. The fact that the PBM model equation Inverse Problem is degenerate or underspecified is demonstrated. Multiple solutions to the same PBM equations are provided. It is shown that there is no unique solution to the Inverse Problem unless additional constraints are provided or assumptions are made such as the Arbiter-Bhrany normalisation assumption. The severity of the non-uniqueness problem for steady state grinding is demonstrated in several examples using typical feed distributions and mill matrices. In addition, it is also demonstrated that when higher than single powers are used in steady-state mill matrix expressions during simulation or calculation (or iterative procedures are used during numerical simulation) and four or more size intervals are used considerable amount of error is propagated throughout any calculation. Each solution to a PBM, while giving the same prediction during a single mill pass, gives different solutions or predictions for mill composition upon subsequent passes. In addition, it is shown that there is a problem with building up a grinding mill knowledge base with PBMs. A similar analysis was done for the dynamic or kinetic PBM equations. The fact that the dynamic PBM Problem is degenerate or underspecified is also demonstrated. Multiple solutions to the same dynamic PBM equations are provided. Again, it is shown that there is no unique solution to the Inverse Problem unless additional constraints are provided or assumptions are made such as the normalisation assumption. Each solution to a dynamic PBM, while giving the same prediction for a given grinding time interval, gives different solutions or predictions for mill composition for other grinding times. Actual experimental grinding data was assessed to determine the functionality of mill selection and breakage functions. The functionalities obtained through constraints were compared with those obtained with the normalisation assumption of Arbiter-Bhrany which relates breakage functions to particle size distribution. The capability of the population balance model to predict grinding behavior over time in various mineral grinding systems was assessed. The required functionality of selection and breakage functions for effective prediction of grinding behavior in mineral systems is discussed.

Jan 1, 1993

The primary objective of any planning exercise is to maximise the return on funds utilised while maintaining a safe and socially responsible working environment. In order to achieve this, it is essential that the assumptions applied reflect as accurately as possible the future realisation of the project. In narrow vein mining, the risk that this will not occur can be significantly greater than that associated with other types of mining projects. This results partially because of dramatic effects upon project cash flows with seemingly minor changes in operating parameters such as orebody width and wall rock competency.The validity of a planning exercise can therefore be related to the extent of available data and to the experience and perceptions of the operating entity. The various factors which must be assessed include absolute values and variations in a range of factors, especially the dip and dimensions of the orebody, the geotechnical parameters and anticipated ground conditions, the productivity and production characteristics of the selected mining method as applied to the specific orebody, and the impact of mine access and development.

Jan 1, 1993

By T. P. Smirnoff, R. J. Redmond, K .. N. Murthy

To minimize disruption to the Hollywood District of Los Angeles, a mined station using the New Austrian Tunneling Method (NATM) was developed. This paper presents the key factors contributing to the settlements and dynamic behavior of the unique binocular station design.

Jan 1, 1993

By M. J. Virnig, Peihao Qi, J. Brent Hiskey

The mechanism of gold uptake from iodide solutions by carbon has been investigated. Adsorption isotherms for gold and iodine were established. For activated carbon, approximately 300 mg of gold and 1000 mg of iodine were extracted per gram of carbon at maximum loading. Examination of loaded activated carbon particles by scanning electron microscopy reveals isolated patches of gold deposited on the carbon surface. High-resolution transmission electron microscopy shows that fine gold particles (1-4 nm diameter) are uniformly distributed within the carbon. Iodine was also observed throughout the matrix. The uptake of gold by carbon from iodide solution involves a combined reduction and adsorption process, where the gold iodide species is reduced to the metallic state superficially and adsorbed in the porous structure of carbon. A few experiments for the gold-chloride and gold-bromide systems were carried out for comparison.

Jan 1, 1993

The attachment of a spherical particle to a bubble is theoretically investigated under the condition of a mixed sorption coating of a collector. It is shown that the attachment is determined primarily by the hydrodynamic factor involving the displacement of liquid from the gap between a bubble and a particle. The dependence of the attachment on the state of the surface of particle (sorption coating) is due to a change in the boundary conditions on the interface with water both in the case of surfactant chemical sorption and in that of the physical adsorption of oil. It is demonstrated that at large distances the thinning of a interlayer is facilitated by a physically sorbed collector, while near the bubble this is done by a chemically sorbed one.

Jan 1, 1993

By D Wilson, R R. Vandebeek, R A. Bowes

"As business opportunities are sought around the world, the explosives industry must oftengrapple with the United Nations Transport of Dangerous Goods Recommendations.Canadians have problems in this area that are similar to those of other countries. Thispresentation outlines, through a case study, how a container for shipping ""explosives"" wasdesigned, tested and approved for use by the Chief Inspector of Explosives, the""Competent Authority"" for Canada."

Jan 1, 1993

By D. A. Peterson

Laboratory testing was completed to determine the effectiveness of a fiberglass cable bolt (FCB) as a cuttable rock support for a continuous, hard-rock mining method. The FCB consists of four Polystal tendons combined in a node/antinode fashion, with polyvinyl chloride (PVC) spacers forming the anti-nodes. The largest ultimate pull-out load achieved by the FCB was 22 t (48,400 lb) at 89% of the tendons' theoretical pullout load. This premature tendon failure is accredited to: • differential stresses within the tendons and • differential tendon displacement. An increase in pull-out resistance for a given embedment length is due to: • increased bond area, • reduced interfacial shear and • "wedge" effect. The critical embedment length was found to be 40% less than for conventional steel cable bolts (SCB) at a 127-mm (5-in.) node spacing. An FCB can have up to a 92% increase in load-carrying capacity over a conventional SCB at equal embedment lengths. The load carrying capacity is equivalent to SCB at a 960-mm (37.8-in.) embedment length. Though the FCB is 7.5% more expensive than the conventional SCB (installed), this cost may be offset by increased performance. FCBs are a potentially viable support alternative for continuous hard-rock mining.

Jan 1, 1993

By A. G. Matyas, B. Wasmund, R. C. Francki, K. M. Donaldson

"The construction of large. high-power electric furnaces has been an important factor in the growth of electric smelting technology . New developments in the design and operation of electric furnaces have been spurred by the escalating cost of electric power and increasingly stringent environmental constraints. Key areasofprogress include the application of high voltage to enhance furnace productivity; the installation of novel furnace cooling elements and robust binding systems to extend furnace life; development of process schemes to reduce power consumption by preheating and prereduction of the charge; and environmental control improvements for handling fine dusty feedstocks, and for furnace sealing.This paper reviews these developments and outlines a systematic approach for their application in the custom design of new or retrofit electric furnace facilities.IntroductionThe use of electric smelting furnaces has continued to progress during the last decade. Electric furnaces offer high throughput capacity and productivity. In addition, they produce minimum environmental impact, as the furnaces can be readily sealed, and only a small quantity of off-gas is generated. Electric furnaces present the most favourable choice of smelting technology where high process temperatures in excess of about l400°C are required.Their application is burdened by the escalating cost of electric power, hence it is important to seek new opportunities through further technological development. This paper reviews recent developments in the design and operation of high-power electric smelting furnaces, in the following areas:"

Jan 1, 1993

By Les W. Armstrong, Stephen B. Richardson, Neville T. Moxon

A study was carried out to determine how different degrees of stemming confinement, that is the retention of the explosives gases, effects fragmentation and movement during blasting.

Jan 1, 1993

By M. D. Johnson

The San Andres mine, located in the western mountain region of Honduras, Central America, contains epithermal gold mineralization as disseminations, in quartz-chalcedonic veins and stockworks. Host rocks include a thick sequence of Cretaceous to Tertiary conglomerates, sandstones, rhyodacite tuffs and andesites. Mineralization is controlled by northwest and northeast striking, normal faults and fractures which dip steeply east and west. Currently, 500 STPD of 1. 93 Grams/MT gold ore is being open-pit mined from the conglomerate and andesite. The mine is at the west end of a mineralized zone that can be traced over an area of approximately 1.5 square kilometers.

Jan 1, 1993

By J. Douglas Causey

The Bureau of Mines conducted mineral investigations of the Peace Rock and Deadwood River roadless areas in Idaho, in 1992. Literature research was done by the Idaho Geological Survey. The study areas contain black sand placers (thorium, columbium, tantalum, titanium, uranium, and rare earth elements), gold, and molybdenum prospects. Except for unrecorded placer gold, there has been no mineral production from the areas. No mineral resources were delineated, but a multi-million tonne molybdenum resource is in the Big Pine Creek area and a 142 million m' black sand deposit is in the Stolle Meadows, Peace Valley, and Deadwood River areas. The Deadwood mine produced zinc, lead, and silver. There are six mining districts in and adjoining the areas; Warm Lake, Deadwood, Garden Valley/Lowman, Banner, Summit Flat, and Grimes Pass. Few claims, mostly placer, were active in the study area in 1992. The study areas are underlain by granitic rocks of the Idaho batholith. Most of the deposits are alluvial accumulations of heavy minerals weathered out of the Idaho batholith. Stockwork and narrow veins along shears account for the base and precious metal concentrations. Eleven prospects were examined. Workings consist of drill holes, pits and adits. Geothermal resources (hot springs) occur mainly along the Middle Fork Payette River; Vulcan Hot Springs is a designated Known Geothermal Resource Area. Sand and gravel resources are of local interest.

Jan 1, 1993

By Jeanne A. Zimmer, Andrew B. Cecala, Edward D. Thimons

The Bureau of Mines performed a study to determine optimal locations for longwall face methane monitoring equipment. Longwall face ignitions continue to be a concern to the U. S. coal mining industry. Gains in ignition control technology have been somewhat negated by advances in longwall productivity. More reliable, heavy-duty longwall face systems generate higher production rates and increase methane liberation rates. These rates will likely continue to rise in the future as further coal production increases occur. Efforts will continue in the areas of methane drainage, methane containment, and methane dilution. In addition, more effective face methane monitoring is needed. As technology continues toward automated longwall panels, the importance of monitoring for methane at the shearer becomes even more significant. Since the primary face ignition source is the shearer mining machine, the Bureau ran tests to determine the best location to take methane readings on the shearer. This information, in conjunction with data obtained from field studies, provides a knowledge base for selecting optimum face methane monitoring locations. INTRODUCTION Face ignitions are a concern for many U. S. longwalls and will continue to be until better control technology can be developed or until reliable and accurate knowledge can be provided as to when an explosive concentration is present. Figure 1 shows the number of reported U. S. underground longwall ignitions from 1980 to 1990. The number of longwall panels have remained relatively constant over this time period with 89 reported in 1980, compared to 96 in 1990. In spite of technological improvements in mining over the past decade, no significant reduction in the number of longwall face ignitions has occurred. One factor contributing to this is that the U. S. coal industry is mining gassier seams causing methane liberation rates on the average to be higher (Trevits, 1991; Grau, 1987). Another factor is the development and implementation of more reliable, heavy-duty longwall face systems that are generating higher production rates and higher methane liberation rates. Additionally, the average panel width in 1991 was 714 ft; a 44 pct increase from 1980 when faces averaged a width of 495 ft (Merritt, 1992). Increases in panel width also impact total face methane emissions. [ ] There have been substantial advances in control technology in the areas of methane drainage, methane containment, and methane dilution. In some mines, efforts to drain methane in advance of mining have proven effective, but geological conditions often preclude this approach (McCall, 1984; Ely, 1989). In other cases, ventilation air quantities of over 100,000 ft3/min and face velocities of over 1,000 ft/min have been implemented on longwall panels. Other operations have implemented anti-ignition spray systems which use water sprays behind each cutting bit to quench the hot streaks created from cutting noncoal materials (Courtney, 1990). Other control techniques, such as the modified shearer clearer system and ventilated drum, have been used to increase the amount of turbulence and ventilation around the cutting drums, thus reducing methane levels (Cecala, 1986; Divers, 1987).

Jan 1, 1993