Search Documents

By Dobias B

A new separation method based on a combination of coagulation and colum flotation was used to treat fine sphalerite in the range 90 per cent - 15 pm with a relative high superfical gas velocity and a thick froth layer. Minerals studied include sphalerite, calcite, kaolinite and baryte. A new developed sedimentometer was used for sedimentation analysis to characterise hetercoagulation of mixture and coagulation after addition of active ions or reagents. A comparison between use of selective frother and depressant (SHMP) was made to deactivate activated minerals. Selectivity of frother for sphalerite was found in flotation test. The depression function of Flotanol for activated minerals was confirmed in sedimentation alalysis. The use of small quantities of HPAM can improve the flotation of fine sized sphalerite particle and reduce recovery of activated gangue minerals in the neutral or alkaline pulp. A satisfactory separation of fine sphalerite from its gangue was achieved by using alkylpolyglycolether (Flotanol) and copolymer polyacrylamide (HPAM hydrolysed polyacrylamide) as frothing and flocculating agents Respectively.

Jan 1, 1993

By Ho-Tun E, Stewart PSB

The definition and recognition of silver minerals is very difficult. In general such minerals occur at low concentration and can be hard to identify and measure using conventional optical mineralogy. The present paper describes the use of the QEM*SEM system to tackle this problem and provide information of use to the metallurgist. Three aspects of QEM*SEM are used to special advantage in this application. Firstly the automated mode of operation is used to make a rapid search for the sparse phases. Secondly the X-ray capability is used to identify the mineral phases. Finally the image analysis programs quantify the distributions of the minerals which are found. The paper deals with the identification stage of the process and with the use of the data which can be derived. Silver minerals which covered a range of ore types and composition were collected and studied in detail. On the basis of these measurements and information received from a number of mining companies regarding the important minerals, a classification table was prepared. This table listed about 40 different silver mineral types which could be identified by QEM*SEM and which were of interest in silver recovery processes. Where the silver occurs in solid solution in concentrations greater than about one per cent, the silver content in the species was subdivided into ranges based on statistical intervals. The QEM*SEM system was programmed to recognise these as separate species. Examples are presented of the use of the system in defining the type and morphology of the silver mineralisation to assist in the assessment of batch flotation test Samples.

Jan 1, 1993

By R. Y. Wan, Corby G. Anderson, L. Ernest Krys, M. C. Fuerstenau

Since 1942, refractory precious metal concentrates at the Sunshine mine have been processed for antimony metal recovery using a novel leach-electrowin method. This is counter to most antimony production facilities where pyrometallurgical techniques are usually relied upon. The key step for removal of the antimony has been an ambient pressure alkaline sulfide leach. In 1990, a comprehensive laboratory study was undertaken to better understand this process. Factors studied included temperature, agitation, concentrate regrind, alkaline species concentrations, sulfur species concentrations and solids concentration. Details of these studies, as well as a brief description of Sunshine metallurgical processes, will be presented.

Jan 1, 1993

By D. Gatzemeier

The Jewett mine is a surface mine in central Texas, producing about 8,000,000 tons/year of lignite. The mine covers 46,000 acres of land. Approximately 430 people are employed by Northwestern Resources Company and through their efforts, the Jewett Mine is one of the most productive mining operations in the country. The Jewett Mine utilizes a unique structure of staff to convert Operations Research into plans which can be implemented at the "front line" level of the Operations Team. This planning not only makes the mine cost effective and efficient, but promotes creativity in mining, which promotes ongoing research to lower the cost of mining.

Jan 1, 1993

By Jun Li

Several metal sulfides were examined in-situ by Raman spectroscopy before and after anodic oxidation. Results obtained for chalcocite, chalcopyrite, covellite, galena, pyrrhotite and pyrite electrodes are presented. Under appropriate conditions, sulfur was detected after a potential was applied to the mineral electrodes for a threshold period of time. For all the minerals, application of a negative potential on the oxidized mineral reduced the surface product and the sulfur peaks disappeared from the observed spectra. For those minerals containing sulfur as S< in the crystal lattice, polysulfides were identified as oxidation intennediates.

Jan 1, 1993

By Schofield N. A

The cross-sectional method of stope grade estimation at Cobar Mines has consistently had several shoneomings, me most imponant of which being mat stope grade is significantly overestimated in the high grade lenses.The use of mree-dimensional ore lens modelling improved the grade estimation and ore waste definition but significant overestimation still occurred in me high grade stopes, particularly those wim extremely variable grade distribution. The implementation of an indicalor kriging based method for mapping of me high grade copper mineralization has significantly improved the quality of copper grade estimates and provides a mineralisation geometry similar to that generated manually by me mine geologists. This paper presents the results of a test case study in the application of indicator kriging to the mapping of the copper grade in two stopes in the QTS North mineralisation. The results are encouraging in that they prov ide coofi rmation of the geometrical model developed by the geologists and much improved estimates of the grades of me stopes whencompared to me grade reponed from mining these stopes.

Jan 1, 1993

Federal lands often contain extensive mineral resources and decisions affecting access to those lands are made with knowledge of the possible minerals-related consequences. Information is provided to the Bureau of Land Management (BLM) in this report for use in preparing environmental impact statements on the Western Mojave Management Area (WMMA) and the Desert Tortoise Priority Habitat (DTPH). To augment U.S. Bureau of Mines (USBM) efforts such as the Mineral Assessment of the Planned Foil Irwin Expansion, Modified Silurian Valley Alternative, San Bernardino County, California which is in progress, and the Economic Analysis of the Minerals Potential of the East Mojave National Scenic Area; California, the USBM studied mineral deposits and estimated the potential impacts of mining in a segment of the California desert; the 8.7-million-acre WMMA, an area which includes the 1.2-million-acre Desert Tortoise Priority Habitat (DTPH). In addition, this information is intended to assist administrators, legislators, and the concerned public in understanding the economic importance of mineral resources in the California desert, especially that portion designated as the WMMA. See figure 1.

Jan 1, 1993

By John C. Taylor

With growing emphasis on energy conservation and increased concern over the presence of heavy metals in the environment, it is fortunate that most metals are readily recycled. In this respect, metals have a significant advantage over plastics and similar materials used as metal substitutes. For many years a secondary industry has processed scrap copper, nickel, lead and zinc to produce refined metal which has, to varying degrees, influenced the price and displaced the production of primary metal. This paper reviews some of the challenges the industry will face and the changes in process technology which will be required as pressure mounts to increase the amount of metal recycled. In the case of most base metals, this will have an impact on primary metal production; as the tonnage of metal recycled increases, the requirement for primary production, or new metal, will depend more and more on the growth in consumption.

Jan 1, 1993

By Wang Hao

"Demolition of reinforced concrete frame structures in building crowded cities is a hardproblem in control blasting. Any mistakes, e.g. wrong toppling direction of multi-storeybuilding or incompleted blasting of structures will all cause terrible accidents.To demolishframe structures safely, various disciplines including structural mechanics, explosionmechanics, rock engineering, etc. are involved"

Jan 1, 1993

By V. Rajaram, D. P. O’Connor, L. Sakamoto

In 1988, the Metropolitan Water Reclamation District of Greater Chicago (MWRD) imposed a no-blasting specification (blasting is restricted to the construction shaft and shaft bottom or boot) on the Deep Tunnel project. This was prompted by numerous complaints from residents in the vicinity of the project and controversies experienced on previous projects from blasting the rock overlying the tunnel. This paper will describe the methods used by two major contractors driving 20 km (12.5 miles) of tunnel, and drilling more than 36 shafts under this restrictive specification. The impacts are detailed on design, construction, schedule, cost and the environment.

Jan 1, 1993

By R. Jedrzejczak

Endako Mine is an open pit molybdenum mine located in the north central region of British Columbia, Canada, approximately 160 km. west of Prince George. Production for the latter part of 1992 is expected to average at 63,500 tonnes per day of which 27,000 tpd constitute the mill feed. This production is achieved with five 15 to 19 cu. yd. electric shovels, six Euclid R190 and two Unit Rig M120 diesel-electric haul trucks, and three 121;.1 inch electric rotary drills. There are three ore zones delineated into pit areas called the Endako, Denak East and Denak West. Present mill feed source is the South East stage of the Endako Pit while the stripping is carried out in the South Wall stage also of the Endako Pit. The mine high grade aggregate is reduced in the primary and secondary crushing circuits before processing in conventional RM/BM/flotation circuits. The majority of the Molybdenum Sulphide (MoS2) is roasted on site to produce technical grade Molybdenum Oxide (MoO3) while a portion is further refined and treated to yield a 99.9% pure Molybdenum Sulphide (MoS2) "Ultrapure" product.

Jan 1, 1993

By Ault A. R

The recent modernisation program at the Risdon electrolytic zinc smelter of Pasminco Metals - EZ (PMEZ) inyolved significant changes to the composition of cell electrolytes. The most significant were increased acidity and sulphate level, a reduction in Co level, and the replacement of 2-naphthol in the additive mixture with licorice. In determining acceptable operating ranges, a relatively large number of industrial deposition tests under controlled conditions was required. The cathode zinc deposits so produced were examined in terms of overall appearance, crystal structure according to X-ray diffraction, and a micro-roughness parameter. Beginning with typical deposits produced in the presence of an excess of one of the addition agents glue or antimony or a mist suppressant (licorice or 2-naphthol), a simple classification system was developed. In this system, the deposits are divided into the following types: Doughy, Pinholed, Compact and Stressed. There was a weak correlation between deposit type and crystal orientation. In terms of ease of stripping, observations in plant operations showed that only Compact and Pinholed were consistently acceptable. Current efficiency was normally maximised by producing a Compact deposit. Process variables such as zinc concentration, temperature and the use of strontium carbonate were found to cause changes in deposit type if the reagent mixture used was unchanged. From the knowledge gained, guidelines were developed to allow glue and antimony additions to be altered to fit new circumstances. The simple classification system was first used to expedite recovery from undesirable morphologies and then to optimise individual cell units operated under substantially different conditions. It is believed that finer control could be exercised by determining the micro-roughness of Compact deposits. However, difficulties can arise if sudden, large deviations occur and go undetected. Suggestions are given for an improved additive control system. The classification system developed has been compared with published information in the literature, and good correspondence was noted suggesting a predictable relationship between short-term, laboratory deposition tests and observable phenomena in industrial electrowinning cells run under steady conditions.

Jan 1, 1993

By B. C. Bhowmick, B. B. Dhar

Central system of ventilation, adopted almost universally in coal mines of India and elsewhere in the world, has often proved deficent in providing a cost effective solution to the acute ventilation problems of remote workings in many mines. Loss of air due to leakage through a number of stoppings, doors etc. and accumulation of heat and moisture by intake air on its way to a working through long and circuitous route are the main unavoidable reasons for low efficiency of the system, sluggish and oppressive ventilation of workings. Multi-zonal ventilation system using large diameter bore holes for feeding fresh air in the mine close to a working has been proposed as a viable economic alternative. The method promises to provide congenial environment at working faces without resorting to air conditioning or use of booster fan. Optimum location and diameter of bore holes as well as general design procedure have been dealt in the paper. Finally, the technical as well as economic advantages of the method over the conventional design have been highlighted with the help of a case study where ventilation system of an extensive shallow mine in Central India has been redesigned according to the old and the new concepts. The methodology is general enough for adoption elsewhere in other mines under similar circumstances.

Jan 1, 1993

By Thomas W. Camm

The U.S. Bureau of Mines has developed a system for estimating mining and processing costs as a function of process feed rate with the objective of applying this system to abandoned mine tailings and to evaluate the benefits, if any, of metal recovery. Cost analysis was applied to the mine wastes of Smelterville Flats: an extensive area of mine tailings in the Bunker Hill Superfund Site with high concentrations of lead, zinc, and other sulfide minerals. Results from previous site characterization and metallurgical processing studies were used as the input for the cost analysis. This analysis indicated that processing this site at an optimum production rate of 3,500 short tons per day (st/d) could generate a positive cash flow.

Jan 1, 1993

Shear-flocculation is one of a munber of potential processes for upgrading deposits of finely-grained minerals and, more generally, for separating different types of particles suspended in a fluid.The smaller the particle the more likely it is to follow the fluid streamlines, or be entrained within turbulent eddies, and the less likely it is to deviate from the streamline and attach to bubbles (froth flotation), other particles (selective flocculation) or magnetic poles (wet magnetic separation). As shown in Figure I, a number of ingenious ideas have been proposed to overcome this effect. The suspended particles are assumed to be 1 - 10 &#181;m.Thus, the efficiency of attaching ultrafme particles of the valuable component (solid circles) to air bubbles, as in process A, is poor. The efficiency may be improved by attaching the particles to oil droplets (Ralston, Kart and Newcombe, 1984) to form agglomerates that rise or sink (B), to magnetic particles (C) (Parsonage, 1988) to allow recovery in a magnetic separator (D), to other particles to form aggregates (E) that are then either attached to bubbles (F) or recovered by sedimentation (G) (Warren, 1992), and to pieces of polyethylene (Rubio and Baltar, 1991) that rise or sink (H).In A, C, E, F and H, the forces that are generally used to ensure collisions result in adhesion are hydrophobic forces, hydrodynamic forces and inertial forces (Warren, 1992). These drag particles from the streamlines to allow particle-particle adhesion. In B and E, soluble polymeric molecules have been added to bridge between particles as they approach closely during a collision.The second major consideration is selectivity. Selective adsorption of the hydrophobe or polymer onto the valuable particles is the key. Many subtle effects of surface chemistry are involved in obtaining adequate selectivity. A complication in real systems is that the initial suspension is often naturally coagulated and needs to be dispersed before being selectively flocculated.

Jan 1, 1993

By J. A. Brierley, C. L. Brierley

The history, current applications and future of biotechnical developments in the metals&apos; extraction industry are reviewed. Bioleaching of copper minerals continues to be the most significant application. Uranium bioleaching was successfully demonstrated at industrial scale. Developments are now being made in biooxidative pretreatment of refractory gold concentrates, ores and low-grade materials. Advancements are forthcoming in water and solid mine waste bioreclamation, including metals&apos; biosorption, wetland treatment of acid mine drainage, and biodegradation of cyanide in spent, heap-leach operations. Better understanding of the types and functions of microorganisms involved in metal interactions could advance genetic engineering applications in bioleaching and bioreclamation.

Jan 1, 1993

By Oliveira JF

Thiourea is an alternative reagent for cyanide in gold leaching. The recovery of gold from acidic thiourea solutions by adsorption on activated carbon is based on methods similar to those applied for the extracting of gold from cyanide solutions, but the mechanism involved in the process is not completely understood. In the present work, studies were carried out to evaluate the adsorption of gold onto activated carbon. Experimental data showed good agreement with both the Freundlich and Langmuir isotherms. The adsorption of gold from acidic thiourea solutions proved to be an endothermic process, while the adsorption from cyanide is known to be exothermic. The isosteric heat of adsorption of -11.3 kcal/mol in the early stages of the adsorption is an indication of a process involving chemisorption. The effect of temperature was studied between 15¦C and 55¦C. An activation energy of 3.5 kcal/mol was determined by the Arrhenius plot, which indicates that the controlling step in the kinetics of adsorption is the diffusion onto the porous structure of the activated carbon.

Jan 1, 1993

By J. M. Goris

The U.S. Bureau of Mines, in a cooperative project with the University of Utah, Salt Lake City, UT, and Homestake Mining Co., Lead, SD, conducted in situ monitoring and numerical modeling of rock masses supported with cable bolts in two mechanized, cut-and-fill stopes and a shaft pillar at the Homestake Mine. Extensometers were used to measure rock displacement, while cable bolt strain gauges were installed to measure loads on both conventional and birdcage cable bolt supports. These instruments provided an assessment of rock mass behavior during mining as well as essential data for verifying results from computer analyses. The numerical modeling program FLAC was used to analyze cable bolt patterns and supports. Results from the evaluation study indicated that cable bolt strain gauges and extensometers were effective instruments for monitoring the behavior of rock masses supported with cable bolts. Also, numerical modeling of the 4S-48N stope using the FIAC code provided displacement values comparable with measurements from field extensometers.

Jan 1, 1993

By G. Andrews

This case study details the process that was used for project planning and permitting for the Greens Creek Mine, located near Juneau Alaska, as seen through the eyes of one of the primary environmental consultants. This case shows how a Company could involve the public and the agencies in the early 1980&apos;s and develop a project sensitive to concerns expressed with a high level of environmental protection. Comparisons are made to the current environmental permitting situation. Initial baseline studies performed during the exploration phase provided helpful information for more detailed environmental work in 1980-1981 as planning and permitting formally got underway. Since the mine was in a National Monument and abuts up to a designated wilderness, the Monument Manager administered the project for the lead agency, the USDA Forest Service. Planning and permitting progressed smoothly to a Final Environmental Impact Statement (FEIS) in 1983. Metal prices were depressed when the FEIS was completed and the project permitting proceeded slowly. Ownership changed several times in the mid-1980&apos;s. New owners re-evaluated the project and suggested five changes that required a supplemental EA prior to development. The project was fully permitted and started construction in 1988. Operation began in 1989. Today the environmental process in southeast Alaska is now much more complex, detailed, expensive, and time consuming than in the early 1980&apos;s. Significant issues discussed that may impede development and operation include overlapping agency jurisdictions, personal agendas of agency staff, conflicts between agencies that impede project progress, changing regulations, and a well organized environmental opposition.

Jan 1, 1993

By D. W. Ashman

Today the electrolytic zinc industry is facing unprecedented environmental pressure and low metal prices. Zinc plants have to decide how they will dispose of iron residues in an environmentally friendly way without major capital expenditures. Only low-cost producers will survive, so companies must continuously improve to stay competitive. Therefore, the challenge of the process engineer is to find innovative solutions to the industry&apos;s problems. This paper reviews the status of electrolytic zinc processing and provides some insight into how the industry will respond to the pressures facing it

Jan 1, 1993