Search Documents

By B. R. McEwen, A. N. Samis, J. H. Gray

"The Quebrada Blanca Copper Mine is an open pit copper project located at 4200 m elevation in the Chilean Andes. The deposit is a world-class supergene enriched porphyry with a mining reserve of 89 Mt of 1.3% copper. The supergene zone will produce 6.3 Mt of ore per year for more than 15 years to produce 75 000 t of cathode copper per year.This paper will review the project geology the computer model ling of the deposit, the mine planning process and the property production scheduling. With copper production .fixed by the onsite electrowinning capacity, the planning and scheduling aspects to optimize the project NPV will be discussed. Some of the logistics, equipment. personnel and process difficulties of operating a mine at 42()() m elevation will also be described. IntroductionProject DescriptionThe Quebrada Blanca Copper Mine is an open pit copper project located in the northern part of the Chilean Andes. The project is based on the supergene enriched portion of a porphyry deposit which has a mining reserve of 89 million tonnes at 1.3070 copper. Below the enrichment blanket, the protore represents a further resource.All ore will be leached, the higher grade material will be crushed and stacked for thin layer heap leaching, and the lower grade and oxide material will be dump leached as run-of-mine material. Solvent extraction and electrowinning will be used to produce 75 000 tonnes of cathode copper per year. Power will be supplied by a 40 MW on-site diesel generating plant with the waste heat being used for process heating. The leaching operation will operate in excess of 15 years and may be followed by open pit mining and conventional ore concentration of the underlying primary sulphide mineralization.Because of the dry location water will be piped 37 km from a ground water source at the Salar de Michincha. Water requirements will be approximately 1.5 million m3/year. The operation will eventually employ approximately 550 people on a 7-day-on, 7-day-off rotation with two twelve-hour shifts per day with an on-site camp. Busing will be provided to the port city of Iquique."

Jan 1, 1994

By Philip Bonanno

The first major project in Boston's new access to Logan Airport was an Immersed Tube Tunnel which extended 3,600 ft. from South Boston to East Boston across Boston Harbor. Twelve tube sections, 300 ft. long x 80 ft. wide x 40 ft. high, were lowered into an excavated trench which was then backfilled. The depth of the trench at mid-channel was approximately 100 ft. below mean high tide. At the East Boston end the tube terminated close to the present shoreline. At the South Boston end the tube terminated approximately 600 ft. inland from the shore line where a ventilation building was required. The depth to subgrade from existing ground at the ventilation structure was approximately 85 ft. The soil profile at this location consisted of 50 ft. of miscellaneous rubble fill, 25 ft. of Boston blue clay, and 10 ft. of glacial till. A small amount of weathered argellite existed at the north end of the structure. Part of the Morrison Knudsen, Interbeton, J.F. White, Joint Venture contract to construct the Immersed Tube Tunnel (ITT) was the construction of a cofferdam at the tube/ventilation building interface. The ventilation building was to be built as part of another contract. The construction of the cofferdam and the excavation to the building subgrade was the responsibility of J.F. White Contracting Company.

Jan 1, 1994

By A. L. Garassino

Dans cet article on parle sortout de l'approche de calcule pour les pieux charges horizontalement avec particuliere reference aux curbes p-y et è une solution semi-empirique qui prende en consideration les variations typiques du module du sol avec la deformation obtenue par les données expérimentales. 1. INTRODUCTION The analysis of the piles under lateral loads depends very strictly from the pile stiffness and geometry, from the soil type and from the strain field. Different approaches were adopted in solving the problem. Some Authors developed methods for estimating the ultimate lateral resistance of piles and pile groups by conventional static approaches, as the Brom's widely known (1964) or by the plane strain solution developed by Davis (1961) or by empirical engineering con­siderations l

Jan 1, 1994

By J. Pang, S. Chander, A. Briceno

The mechanism of sulfur oxidation in pyrite is a function of the rate and driving force for oxidation. New evidence is presented to show that, at moderate potentials, a sulfur-rich hydrophobic layer is formed. Under ordinary conditions, the sulfur layer is covered with a layer of iron oxides, hydroxides, sulfate or oxy-sulfide ions. Pyrite is hydrophilic under these conditions. In the presence of iron-chelating agents or iron sequestering ions, an iron layer might not form. Under these conditions, the sulfur layer is exposed, and the pyrite might become hydrophobic. Stronger oxidizing conditions decompose the sulfur layer, thereby making the surface hydrophilic.

Jan 1, 1994

By W. F. Van Impe

The design of piles and of pile groups has remarkably progressed over the past two decades. The in­creasing complexity of the building concept implements a more rational approach of the deep foundation capacity and its interaction with the structure. Moreover, the understanding of the soil characteristics relevant to deep foundation behaviour, is continuously in progress because soil parameters are always more accurately determined; which also contributed a lot to the recent developments in pile capacity design. At last, due to the increasing sensitivity of buildings to deformations, continuous attention must be also paid to pile group settlements. The aim of this report is to discuss some of the mentioned more important pile design developments.

Jan 1, 1994

By Thomas L. Barkley

This paper describes an unusual design for a 12 foot diameter, 30 foot deep circular shaft shot in a close in urban environment less than 100 feet from occupied structures. It uses diagrams, video footage, and vibration results to describe a 3 deck, 17 hole burn round used to pull 17 feet in one lift.

Jan 1, 1994

By Yutaka Yasuda

The particle dispersion phenomena in a turbulent gas jet of the flash smelting process has been investigated. The particle number density in a non- reacting jet was measured experimentally by taking photographs of the particles in flight and counting them using the image analysis. Numerical computations were also performed using a mathematical model for a turbulent particle laden gas jet The experimental particle number density data were then compared with the predicted results of the model. Good agreement was obtained between the experimental and predicted data. The effects of the parameters such as the injector design, particle loading and air flow rate are discussed. Optimization of the concentrate burner design can be achieved with the help of experimental and theoretical simulation as performed in this work.

Jan 1, 1994

By Betty L. Gibbs

What does the information age mean to mining companies? The perception of greatly increased access to information is based on modern communications through ‘smart’ fax machines and computer networks. Computer media allow us to `talk' to the President or to a sister in Australia. If we need data to help put together a mining permit, we can find that data somewhere on computer media. The vast amount of easily accessible information quickly overwhelms us. To avoid `information burnout,' we must learn to target searches and be able to discriminate between dross and information that is useful to our goals. If you watch commercial TV, you have learned to screen out most product commercials. A similar screening process must be applied to computerized information sources. You may need to sort through a lot of irrelevant information before finding the pearls you are looking for. ‘Smart’ fax machines can send information with no direct human intervention. MINES FaxBac, for example, from the US Bureau of Mines instructs you to enter four-digit numbers to have particular reports sent directly to your fax machine. Software vendors use a similar system to supply information about their products. You select an item by number, and the related brochure is faxed to your machine. To compete, the industry must maintain access to as many information sources as possible. The availability of computers and software for almost every conceivable application allows us to accomplish work faster than we ever thought possible, even as recently as 10 years ago. Most mining companies have become aware that doing geology, reserves, mine planning and other technical tasks completely by hand is much too slow. The world moves faster, drilling happens faster, mining happens faster, all related activities happen faster. We no longer have the manpower or time to keep all maps. calculations and records up to date.

Jan 1, 1994

By Niels Krebs Ovesen

Close economic cooperation was established among the countries in western Europe during the seventies. As a consequence, among others, a need for harmonized technical specifications for civil engineering works arose. Technical specifications for design and execution of building and civil engineering structures exist in most of the European countries. In some countries such technical specifications are part of the building regulations and in other they are independent codes of practice and standards. The works on the Eurocodes was initiated by the Commission of the European Communities about 1976. The Eurocodes are intended as common unified design codes for different load bearing structures constructed from different materials. They are also intended to cover design of geotechnical structures. They are established with a view to promote the free movement of goods and services within the member states of the European Community - the so called Internal Market - and within the member countries of the European Free Trade Association, EFTA by removing obstacles arising from different rules for calculation and design.

Jan 1, 1994

Locating subsurface conductive solutions is important for many applications, including in situ mining and environmental protection. Drilling boreholes for sampling is expensive and can increase contamination by mixing water from different aquifers. Various noninvasive geophysical methods are available, but previous comparisons were hampered by different methods being used at different sites or at different times. The U.S. Bureau of Mines (USBM) compared methods at one site using the same conductive solution to improve the reliability of the comparisons. Locating deep (> 100 m) solutions is most difficult, SO the USBM selected methods applicable for such depths. Objective Improve the ability to locate subsurface conductive solutions by evaluating and comparing applicable geophysical methods. Approach The experiment was performed cooperatively with other agencies to increase the number of methods studied. The USBM, the University of Arizona, Sandia National Laboratories, and Zonge Engineering and Research, Inc., conducted cooperative field tests of six electromagnetic (EM) geophysical methods to compare their effectiveness in detecting salt water brine of conductivity 3.6 S/m collecting at the water table, 157 m subsurface. The brine was injected through two boreholes. The test site was the University's San Xavier experimental mine near Tucson, AZ. Geophysical surveys using surface and surface-borehole, time-domain electromagnetics (TEM); surface controlled-source audiofrequency magnetotellurics (CSAMT); surface magnetic field ellipticity, surface-borehole, frequency-domain electromagnetics (FEM); and crosshole FEM were conducted before and during brine injection. A total of 110,000 I. of brine was injected over one week, but the effective target volume of brine was much smaller because of mixing with ground water and dispersion.

Jan 1, 1994

By Joseph W. Hejny, Marlyn G. King

Coal mining in the Powder River Basin has changed in recent years to accommodate the large quantity of coal produced. With strip ratios of one to one and up to three to one, extensive amounts of overburden have to be removed to get to the large thick seams of coal. Larger shovels and trucks have been implemented in the removal of this overburden. The addition of draglines and continuous miners have been added to increase the production of coal. Drills used today are capable of drilling up to 13.5 inch blast holes.

Jan 1, 1994

By D. K. Panda

The behavior of single drops with gas evolution at the interface is of interest because this is one of the important reactions that occur in oxygen steelmaking vessels, where a large amount of iron-carbon drops are dispersed in an oxidizing slag. The carbon dissolved in these drops, reacts with the slag to form CO, which is evolved as a gaseous phase. A room- temperature model was used to study the nature of this type of reaction including the effect of various factors such as viscosity and the presence of surface active impurities. Experiments were done for reacting drops over a wide size range to observe various regimes of behavior. Large single drops were levitated in a counter current flow to produce a sufficiently long residence time to allow the study of the various stages in the reaction. The emphasis of this work was to obtain photographic evidence of a high quality to describe all possible modes of behavior, and so a lot of effort was given to developing and perfecting experimental techniques.

Jan 1, 1994

By W. C. Lacy

It is the responsibility of educators to look ahead and prepare young engineers and scientists to cope with industrial and social problems of the future. We are faced with a review of history as well as prophesy of the future. The mining industry exists in a "bubble" with little interaction or communication with the outside. This isolation must be broken down if the industry is to survive in the U.S. and Canada. The ability to communicate with the general public and public officials is essential. Many changes are occurring that will require readjustments in technology and staffing. Aging population will result in raising retirement and increasing available workforce. This may force shorter working weeks to supply additional jobs. Environmental concerns will likely direct more attention not only to these concerns during mining, but to planning for post-mining land usage. Retraining and up-dating educational programs are required to cope with these changes.

Jan 1, 1994

R F Johnston 1 ABSTRACT The possibilities for bacterial leaching of refractory gold ores found in the Central Victorian region of Australia are examined. The behaviour of bacteria, especially 77iobacillus ferroaridans is outlined and the effects of these when they are exposed to pyrite, arsenopyrite and stibnite are examined. The factors which are particular to Central Victoria are outlined and the possibility of adapting a bacterial culture to suit the conditions is discussed. It is concluded that a bacterial leaching system is a feasible proposition and that it could enhance leaching rates and yields.

Jan 1, 1994

By Michael D. McGill, Jeff Freadrich

There are many factors which affect the productivity of a front end loader. One of the most obvious is the characteristics of the material being mined. Characteristics such as size distribution, swell factor or heave, and material hardness / abrasiveness will all effect the efficiency of the mucking cycle. The focus of this paper is to look specifically at the size distribution of blasted material, and quantify the effects on loader productivity.

Jan 1, 1994

Provide a low-cost, low-maintenance method for im¬proving mine water quality on abandoned mine land (AML) sites. Approach A model (figure 1) is presented for selecting, designing, and sizing one or several passive mine drainage treatment systems that can be used in remediation of AML. The three principal types of passive mine drainage technologies for the treatment of coal mine drainage are an aerobic system, a compost wetland, and an anoxic limestone drain. The multistep approach presented here provides a simplified method to characterize the type and magnitude of the water quality problem and then to select either a single treatment system or a combination of treatment systems to address the specific site situation. How It Works Step 1. Discharge Characterization. Characterization of the discharge consists of measuring the discharge flow rate and collecting water samples at the point of discharge for chemical analysis. Both the flow rate and chemistry of a discharge can vary seasonally and in response to storm events. It is important to account for this variability by determining flow rates and water chemistry under various conditions. Water should be analyzed for pH, dissolved iron (Fe), alkalinity, and hot acidity (using the H2O2 method).

Jan 1, 1994

By L. M. Pruett

The Arizona Legislature is currently in the process of considering mined land reclamation legislation in the 1994 legislative session. A bipartisan legislative study committee has drafted proposed mined land legislation. The committee has attempted to craft legislation that is appropriate for the unique conditions in Arizona. Existing Arizona and federal laws and regulations extensively regulate the environmental performance of mines in the state to protect public health, safety and the environment. The proposed mined land reclamation legislation does not replace or duplicate these statutory provisions relating to environmental protection. Instead, the purpose of the proposed legislation is to provide for the reclamation of land that is being mined and to fill the gap in existing laws by requiring the reclamation of land that currently is being mined or that has been mined since 1986 to provide for future land use. The legislation would require an operator to submit a reclamation plan describing the exploration operations, mining operations, post-mining land use and the proposed reclamation measures for review by a state agency. Financial assurance also would be required in an amount such that a third party could complete the approved reclamation measures. Arizona's mined land reclamation legislation would recognize Arizona's leading role in hard rock mining and emphasize the mining industry's economic importance to Arizona and the nation. Because mining operations necessarily require disturbing the surface of the earth to extract valuable minerals, reclamation requirements would be adapted to different conditions and would vary depending on site-specific conditions and on the commodity being mined. The current proposal does not identify the state agency that will administer the mined land reclamation program and approve reclamation plans, substantial changes to plans, and transfers of reclamation plans to other operators.

Jan 1, 1994

By Jose Luis Lopez Mendez

In May 1992, MEXICANA DE CANANEA, S.A. DE C.V. finalized the life of its Reverberatory Furnace which lasted 16 years. This created the need to prepare the Smelter for the next campaign.

Jan 1, 1994

By Mukesh K. Agarwala

Alloy composite parts were made from powders by Selective Laser Sintering (SLS). SLS is a rapid prototyping process that uses data from CADICAMICAE systems to guide a laser beam and rapidly form 3-D prototype parts from powders without any part specific tooling. In this study, Bronze-Nickel parts made by SLS were studied for their mechanical properties. To make the parts structurally sound, SLS parts were further processed by conventional isothermal sintering, without loss of shape. The resultant densification and mechanical properties were studied and related to microstructures and P/M densification models. These results were then correlated to the SLS processing parameters.

Jan 1, 1994

By Thomas M. Barczak

The engineering of a support system is driven largely by economics. The goal is to provide effective support at minimal cost. For this reason, wood has been extensively used as a support material for centuries. The cost of timber for mining applications has risen by more than 50% in the past 5 years and is likely to continue to increase as the supply diminishes and further environmental restrictions are placed on timber harvesting. The increased cost and lack of high strength wood in the Western United States has provided incentives to improve the utilization of wood and to develop alternative support materials. This U.S. Bureau of Mines' (USBM) report discusses the basic engineering requirements for the application of various materials for supplemental roof support construction and provides an overview of support systems that use materials other than wood. A comparison of support performance and cost for various material constructions is made to assist the mine operator in support selection. The scope of materials discussed in the report include: (1) conventional mine timber loaded perpendicular to the grain, (2) parallel to the grain timber loading, (3) steel fiber reinforced and air entrained concrete, (4) steel, (5) granular fill materials, and (6) combinations of these as composite support structures. The range of support systems analyzed include wood and concrete cribs, concrete columns and props, steel beams, friction props, and several novel support concepts.

Jan 1, 1994