Search Documents

By J. A. Frew, R. M. Glen

Recovery of galena and sphalerite from fine grained lead-zinc ores by flotation normally requires re-grinding to achieve economic recoveries at acceptable concentrate grades. Re-grinding aims to reduce the coarse valuable mineral particles to a size where they float more readily and to liberate the composite valuable particles so that the gangue in these composites does not dilute the concentrate. Besides changing particle size and liberation, re-grinding changes the surfaces of the minerals and thus may alter the rate that mineral particles of a given size and liberation float. A method was developed to apportion the total change in recovery after re-grinding between changes in size and liberation and changes in flotation rates. The flotation behaviour of minerals, before and after re-grinding, was measured by floating samples of plant streams under controlled conditions in a laboratory cell. Results from several industrial lead-zinc circuits indicated that the change in behaviour observed fell into three different categories. It is concluded that the method will indicate whether the focus for optimization of existing plant should be on comminution or flotation, and it will help determine the path for laboratory testing in designing new regrind circuits.

Jan 1, 1995

By M. J. Sanzotti

This paper examines the potential for controlling longwall-induced subsidence by pneumatically backstowing the void created by mining with waste rock, and having the process scheduled as a unit operation of the mining activity. Based on a review of background literature, interviews with representatives of various mining companies, public-interest groups, and state and federal regulatory agencies, a hypothetical case-study evaluation of pneumatic stowing in a southwestern Pennsylvania mine site was conducted. The study indicated that current stowing technology cannot keep pace with the production potential of U.S. longwall systems. Further, at the case-study mine site, concomitant stowing would reduce subsidence by only 50% of that incurred during full longwall caving, the longwall coal production rate would decrease from 4000 tons per shift in the non-stowing case to 1500 tons in the stowing case, and a preliminary cost analysis reveals that pneumatic stowing would add $5.25 to $10.50 to the operating cost of producing a ton of coal at the case-study site.

Jan 1, 1995

The transgressive sedimentary sequence of the Noumea Basin contains rhyolitic lavas and less voluminous mafic and intermediate volcanics of shoshonitic affinities which erupted simultaneously during the late Cretaceous. The shoshonitic volcanism shows a trend froIn early mafic to younger evolved intermediate lithologies. The rhyolites are consistently calcalkaline. There is no evidence of mixing of the two magma types. The shoshonitic volcanism is the result of a short-lived subduction event related to spreading in the New Caledonia Basin and involved reactivation of an earlier esozoic subduction zone.

Jan 1, 1995

By E. R. Slatick

The northern and central Appalachian coal basin in the eastern United States has been the source of about two-thirds of the nation's coal output during the 20th century. This region includes parts of Pennsylvania, Ohio, Maryland, West Virginia, Virginia and eastern Kentucky. It covers about 130,000 km2 (50,000 sq miles) of the Appalachian coal basin and ranks as one of the world's most important coal production regions (Fig. 1). The coal industry's heyday in northern and central Appalachia has passed. This was due to competition from other fuels and low-sulfur coal produced in the West and because of the declining use of coking coal for steelmaking. Nevertheless, the region still plays a vital role in US coal production. It currently produces about 40% by weight of the nation's coal (its share is about one-half when measured by the energy content of the coal), contributes substantially to electricity generation and serves as the mainstay of US coal exports.

Jan 1, 1995

By E. Topuz, M. J. McPherson, I. M. Konduri

The research is carried out to investigate the flow mechanics and effectiveness of face ventilation using induction fans, as an effort to provide a more efficient alternative to conventional auxiliary duct or brattice ventilation systems. The induction effects and plume longevity of fluid jets are being studied with the help of a plexi-glass model, using water as the fluid medium and creating a system that is dynamically similar to the flow in mine headings. This scaled model represents a typical 1.5m x 6m x 25m heading connecting to a crosscut. Reynolds Number criteria are used to obtain dynamic similarity of the flow in the designed model to simulate real mining conditions. The role of various parameters such as nozzle position in three dimensions, airway roughness, nozzle geometry, and flow rate in the jet are studied. During the laboratory tests, flow visualization techniques, coupled with still and video photography, were employed to identify the flow patterns. The results indicate that in typical coal mine headings, jet fans can produce effective face ventilation for distance up to 30 meters.

Jan 1, 1995

By Casale G

This paper discusses a long range mine plan development at the Santa Fe Pacific Gold Twin Creeks Mine based on the reserves of Mega pit. The key constraints of the schedule development included two types of mill ore targets (sulphide and oxide mill ore), consideration of blending of six chemical constituents (sulphide sulphur, carbonate, organic carbon, the ratio of iron/[arsenic, antimony]), and mining of acid generating and acid neutralizing waste at pre-defined proportions. Solution approaches, selected results, and project experiences are discussed.

Jan 1, 1995

By A. D. Davis

A ground-water flow model was developed to simulate the post-mining recharge rate at the Belle Ayr surface coal mine in the Powder River Basin near Gillette, Wyoming. State regulations of Wyoming require that reclaimed lands should provide a rate of recharge that approximates the pre-mining rate. Steady-state calibration and transient simulations showed that the post-mining recharge rate in backfill is at least five centimeters per year, exceeding the original infiltration rate of 0.4 centimeters per year to shallow, overburden aquifers. Major reasons for the increase include the flat topography of reclaimed areas and decreased spoil density. It is expected that the backfill will disaggregate and settle over time, eventually resulting in a nearly constant recharge rate less than five centimeters per year but somewhat greater than the pre-mining rate.

Jan 1, 1995

By Hayati Karaman, Tevfik Güyagüler

In this paper fires due to spontaneous combustion in Middle Anatolian Lignite mine (OAL) which is the first fully mechanized underground lignite mine in Turkey, are studied. Since the installation of mechanization (1986), due to spontaneous heating, four panel fires namely, A01, A02, A03 and A04 have broken out. During these fires, the concentrations of carbon monoxide, methane and the velocity of air are measured continuously by the Micro Minos Environmental monitoring system. For each fire, the environment where fire has started is examined and the possible causes of the fire are investigated. Also the precautions taken to extinguish the fire at different stages are described and the importance of the early detection of mine fire are discussed together with the limitations of the monitoring system and the practical difficulties observed during the fire.

Jan 1, 1995

By Joseph C. Zelanko

Cable bolt support techniques. including hardware and anchorage systems, continue to evolve to meet U.S. mining requirements. For cable support systems to be successfully implemented into new ground control areas, the mechanics of this support and the potential range of performance need to be better understood. To contribute to this understanding, a series of 36 pull tests were performed on 10 ft long cable bolts using various combinations of hole diameters, resin formulations, anchor types, and with and without resin dams. These tests provided insight as to the influence of these four parameters on cable system performance. Performance was assessed in terms of support capacity (maximum load attained in a pull test), system stiffness (assessed from two intervals of load-deformation), and from the general load-deformation response. Three characteristic load-deformation responses were observed. An Analysis of Variance identified a number of main effects and interactions of significance to support capacity and stiffness. The factorial experiment performed in this study provides insight to the effects of several design parameters associated with resin-anchored cable bolts.

Jan 1, 1995

By Todd R. Taubert, Kenneth L. Bickel

The U.S. Bureau of Mines (USBM) pioneered the development of disposable filters for reducing diesel particulate emissions from permissible mining machines. The USBM is now evaluating filter media that can withstand the high exhaust temperatures on nonpermissible machines. The goal of the evaluation is to find an inexpensive medium that can be cleaned or disposed of after use, and will reduce particulate emissions by 50 % or more. This report summarizes the results from screening tests of a lava rock and woven fiberglass filter media. The lava rock media exhibited low collection efficiencies, but with very low increases in exhaust back pressure. Preliminary results indicate a collection efficiency exceeding 80 % for the woven fiber media. Testing of both media is continuing.

Jan 1, 1995

By Frank E. McCall, John K. Marshal, Fred Garcia

Since the advent of longwall mining systems in the United States, mine operators are increasingly relying on methane drainage techniques to supplement the ventilation system. The most commonly used technique is the vertical gob borehole. The number and spacing of vertical gob boreholes per panel is generally based on experience and underground conditions. To design a more efficient methane drainage systems, mine operators must accurately determine methane gas produced. Thus, mine operators must monitor gas flow and methane gas concentration on every vertical gob borehole on active panels at least once or twice during each 8-hr shift. As the mine grows, it is possible to have more than one operating longwall and many vertical gob boreholes. Thus, daily visits to each vertical gob borehole site can become very time consuming. During weekends when methane gas concentrations typically drop because there is no mining activity, borehole sites may not be visited. To obtain accurate gas flow data, a gob borehole monitoring system was designed and constructed by the U.S. Bureau of Mines (USBM). Gas flow, methane gas concentration, gas temperature, barometric pressure, and vacuum pressure of the exhaust fan are the parameters collected by the system. The system also includes circuitry for automatic shutdown of the exhaust fan and an alarm system before an unsafe condition is created. Telemetry components were also integrated into the system to allow for transmission of borehole data to the mine office. As a test, the system was installed and operated on a vertical gob borehole for six months. Test results indicated that intermittent measurements with hand-held instruments from vertical gob boreholes were always higher than gas flows measurements made by the gob gas analyzer system. This paper describes the system components, operational characteristics, and the results of the test program.

Jan 1, 1995

By Lee M. F, Guilfoyle K

A large hard rock rib pillar was recently preconditioned at Mt Charlotte mine using a novel blasting technique. The motivation for trialling this procedure was a history of past pillar failures, with associated seismicity. Design studies had shown that a new proposed pillar would be at risk of violent failure, and preconditioning was used in an attempt to reduce this risk. Preconditioning by blasting involves physically modifying a selected zone of ground in advance of mining, then forming the pillar so that it incorporates that zone of ground. The modified rock in the zone is intended to allow extra closure (yield) of the pillar in response to mining-induced stress changes. The ground modification was done by tight firing a blasthole array to fracture the rock. The blast design comprised pairs of pre-split blastholes to create a series of short cracks across the target zone, followed by main blastholes to fracture the rockmass between each pair of cracks. A monitoring program was used to establish whether or not the preconditioning was effective. It included conventional extensometers, stress change cells and closure stations, plus a seismic monitoring system. To-date, stoping is complete on one side of the pillar and has just commenced on the other. Results show significant movements within the preconditioned zone and on geological structures in the pillar, as well as lower stress in the pillar compared to an adjacent non-preconditioned site. The preconditioning technique can be applied elsewhere, provided its purpose, mechanism and side effects are understood. Benefits are likely to include more assured production, and successful pillar recovery even in high stress situations.

Jan 1, 1995

By C. G. Anderson

Historically, the treatment of orebodies for recovery of valuable constituents presents many processing challenges. In a time of heightened environmental awareness, the constraints placed on processing complex orebodies are becoming more and more pronounced. As such, established technologies are limited in their ability to fill the needs of these emerging sources of raw materials. A prime example of this is in processing PGMs from primary sources. Normally, this type of material is found in a nickel-copper-iron sulfide matrix. Typically, these materials are processed by established pyrometallurgical means. However, other options should be considered. Hydrometallurgical processes are available which offer advantages over pyrometallurgical methods. One of these is the nitrogen species catalyzed sulfuric acid pressure leach used industrially by Sunshine Mining and Refining Company. In 1990, laboratory work was undertaken in cooperation with Stillwater Mining Company to test PGM matte materials from the Columbus, Montana smelter. The initial results were very positive, and they led to a design to recover PGMs in a high grade residue and to recover nickel and copper as valuable products. Handling the iron and other wastes in an environmentally safe manner was also successfully investigated.

Jan 1, 1995

By Jones J. P, Arriagada J, Scherpenisse C. R

A recently-developed model is used as a tool to optimise the design of blasts used to create final walls in large open pit mines. The use of this tool has allowed present blasting practice and proposed designs to be evaluated to predict the likely extent of rock damage behind the final wall. The evaluation of the damage is dependent on the predominant local geology. Modelling of damage using the software allows the potential zones of rock damage to be evaluated under the following criteria: I . the extent of new fractures formed in the intact rock mass; and 2. the distance to which dilation and extension of existing discontinuities and pre-existing fractures will likely occur. The computer model has been used to examine present blasting practice and to estimate the damage induced by final and intermediate rows of blastholes. The results of current practices are presented in a visual form that allows simple comparisons to be made for any proposed changes in design. To confirm the predictions of the modelling, physical measurements are being undertaken at selected mines to quantify damage behind blast patterns, and experimental programs are underway to measure near-field vibration, or shock, levels. The computer modelling software is being used to qualify and improve the design of final rock slopes in large surface mining excavations, and to provide site engineers with well-defined design criteria for consistency in design. The model is seen to be just one of many tools which are being used in large open cut mining operations to gain an improved understanding of blasting and blast control.

Jan 1, 1995

By Gregory S. Parker

The explosives community has seen tremendous technological advances during the past several decades. When this industry was in it's infancy and even past, Powder Monkey's defied the odds by relying on daring and cunning to unleash the power contained in nitroglycerin and black powder. Unlike the manufactured improvements, there has been little in professional evolution amongst the blasting fraternity unless provoked (for the most part) by the government. It is the intent of this author to advance the cause of an industry wide training and certification program, uniform in nature and broad-based enough to be voluntary, giving states whose outstanding programs are already in place, the opportunity to provide input. In creating this type of atmosphere, grandfathering, reciprocity and accessibility would be paramount. With ISEE taking a firm leadership role during the inception and NICET's involvement in the administration, the idea postulated here is intended to spark interest and debate, bringing the inception of such a program to the forefront.

Jan 1, 1995

By P. W. Johnson, H. Fan, S. B. Patton, T. Novak, R. L. Sanford

A computer model is presented that quantitatively uses the relationship between the interactive and dynamic processes of methane drainage, mining, and ventilation. The model includes simulation of the coalbed methane reservoir for prediction of gas-emission rates under the influence of degasification wells and longwall mining, ventilation network-generation and ventilation simulation. As mining progresses step-wise through the coalbed-methane reservoir, the ventilation network is created and subsequently simulated, iteratively determining fan requirements to safely reduce methane concentrations. The model can be used to quantitatively study the effectiveness of methane degasitication on the ventilation system in a longwall panel.

Jan 1, 1995

Design and test a high-production coal mining machine that generates less respirable dust. Background Current coal cutting systems generate excessive amounts of airborne respirable dust and fines during the mining process. Dust control technologies, including dust dilution by ventilation and suppression by water sprays, are not always able to reduce dust levels sufficiently. The U.S. Bureau of Mines (USBM) has designed a cutting system that reduces respirable dust generated by the cutting action of the drum. This cutting system, based on geometric principles developed in the 1500's, makes use of a constant depth, linear cut to remove coal at deeper cut depths and at lower rotary speeds than a conventional rotary drum. A comparison of the linear and rotary cut paths is shown in figure 1. Approach A full-scale prototype of the linear cutting concept was valuated under laboratory conditions to determine its performance relative to standard rotary drums. Results of these evaluations show production of fewer fines, or more uniform product size, a significant reduction in the amount of airborne dust, and reduced torque and power requirements (figure 2). On the basis of these results, a contract effort was undertaken by McCracken and Associates of Bristol, TN, to design a linear cutting head for underground testing.

Jan 1, 1995

By Don Z. Painter, Gordon F. Revey

Frontier/Traylor Joint Venture is presently constructing a section of the Tri-County Metropolitan Transit District of Oregon's (TRI-MET) Westside Light Rail system. This new section will extend Portland's existing transit system to the western suburbs of Beaverton and Hillsboro. The drill-blast excavations at this project include 10,000 feet of 20 foot tunnel, 18 cross passages, three shafts, an underground railway station, and a U-wall open cut. From a blast designer's perspective, this job has been extremely challenging. Blast vibration is limited to 0.5 ips at 200 feet or at the nearest structure, and airblast is limited to 129 dB -- linear peak and 96 dB -- C scale. The tunnels pass under heavily built up areas and have top of tunnel to surface cover distances as low as 70 feet. Surface blasting in the 26,000 cubic yard U-wall excavation was limited to five short nighttime periods due to its proximity to the very busy highway 26.

Jan 1, 1995

By J. M. Pugliese

The U.S. Bureau of Mines is developing designs and estimating costs for vertical in situ copper mining wells as part of its in situ mining research program. Conceptual designs and estimated costs for "deep" 1100 m (3600 ft) recovery and injection wells in an undisturbed copper ore zone are presented. Within a single in situ copper mining well, multiple perforated well completions and associated costs are discussed for two ore zones between depths of 370 m (1200 ft) and 550 m (1800 ft). The order of well specifications for designing these wells is explained.

Jan 1, 1995

By M. S. Celik

Salt-type minerals are usually floated with anionic and cationic collectors. Flotation of a number of systems has been reported to remarkably increase above the concentrations where surface precipitation of collector-metal salt is initiated. Some studies attribute this phenomenon to heterocoagulation of oppositely charged collector colloid and mineral particles. In this study, examples are given on boron minerals to demonstrate that the high flotation region occurs when particles, colloidal precipitates and bubbles acquire a similar charge which induces Van der Waals interactions resulting in hydrophobic bonding.

Jan 1, 1995