Search Documents

By B. K. Parekh, R. H. Mehta

The handling of fine coal is an important issue for both the coal and utility industries. Reconstitution of fine coal in the form of pellets or briquettes would be desirable if it could be done economically. This paper evaluates the effectiveness of three binders, asphalt-emulsion, corn starch and Brewex, informing pellets of ultrafine clean coal. It was found that asphalt-emulsion and corn starch were not effective binders. However, the use of Brewex resulted in pellets that exceeded all of the minimum quality requirements for coal pellets.

Jan 1, 1997

By Donald P. Richards, Patrick Ramond, Martin Herrenknecht

Phase 1 of the second line of the Cairo Metro includes approximately 5.83km, of double track tunnels excavated in water bearing sand of the Nile flood plain. Closed face bentonite slurry shield tunnel boring machines 9.43m in diameter were used. State-of-the-art technology was used in TBM operations and guidance, with surface settlements averaging less than 14mm, and alignment deviations averaging less than 25mm. Production rates up to 580m/month were achieved, with average production of 4.8m/shift, 13.4m/day and78m/week. The completed tunnels, lined with precast concrete segments, are completely watertight under 20m of water pressure.

Jan 1, 1997

By N. S. Narayanan

Monazite, one of the major sources of rare earths, is normally opened by digestion with hot concentrated caustic soda solution. Caustic digestion dissolves phosphate and leaves a hydrated mixed metal oxides cake containing thorium, uranium and rare earths. By leaching this cake with hydrochloric acid at pH 3.0 to 3.2 bulk of the rare earths are preferentially removed and separated. The slurry left after removal of major portion of rare earths contains all the thorium and uranium present In the feed monazite. In addition this slurry also contains substantial quantities of rare earths. Solvent extraction tests were carried out to develop a process to separate rare earths, thorium and uranium present in the mixed chloride solution obtained by dissolving the above slurry in hydrochloric acid. Based on these tests a solvent extraction flow sheet was developed with di-2-ethyl hexyl phosphonic acid mono 2-ethyl hexyl ester as the extractant. The details of experimental work and results obtained are discussed and a flow sheet for processing monazite Incorporating the new process is suggested.

Jan 1, 1997

By Choulaj D

Mining and petroleum continue to be the two most vita components of our nation's development, says Sir Julius Char in the Australian Journal of Mining (Nov-Dec 1996). In fact the} account for 71.6% of export earnings, and 21.2% of Gros; Domestic Product in Papua New Guinea. The Misima and Porger, Mines, along with the Kutubu oil project, have essentially rescues PNG's economic viability since the loss of income from Panguna Though the industry cannot create employment in the manner o. intensive industries such as agriculture, it does provid( opportunities to local communities in terms of jobs, financia compensation, and infrastructure. Many ventures take many years and enormous capital investment to set up. There are three phases: exploration, feasibility, an( operations. The operations phase sees a massive development o infrastructure, or the actual `building' of the mine. For mining companies to commit to such lengthy time frames and high level: of investment, without returns, requires confidence and a degree of commitment from government on a number of levels - legislative stability, monitoring social development, and the provision o social infrastructure.

Jan 1, 1997

By W. C. Chang

Phases and magnetic evolutions of melt spun Nd9.5(Fe1-xCox)85.5B5 (x=0, 0.05, 0.1 and 0.15), (Nd1-yLay)9.5Fe85.5B5 (y=0, 0.0.5, 0.1; and 0.15) and (Nd0.95La0.05)9.5(Fe1-zCrz)81.5B9 (z=0, 0.033, 0.067 and 0.1) nanocomposites: have been investigated. It was found that a. dilute Co substitution for Fe, x=0:05-0:15, in Nd9.5(Fe1-xCox) 85.5B5 improved not only Curie temperature but also the remanence and maximum energy product. Partial substitution of La for Nd in(Nd1-yLay)9.5Fe85.5B5 may suppress the grain growth of the materials during thermal treatment. Exchange coupling between the Nd2Fe14B and a-Fe was found: to increase with increasing La content. A dilute La-substitution, y=O. 10, has proven to decrease the optimum wheel speed required for preparing melt spun ribbons with better magnetic properties; Furthermore; a slight substitution of La for Nd in (Nd0.95La0.05)9.5(Fe1-xCrx)81.5B9 nanocomposite reduced the crystallization temperature of the over-quenched ribbons and led to the formation of a multiple phases mixture. Nevertheless, a dilute Cr addition increases the Tg of (Nd0.95La0.05)9.5(Fe1zCrz)81.5B9 and also suppresses the formation of the undesired (Nd,La)2Fe23B3 and Fe3B phases: Cr was found to play an important role in grain smoothening or magnetic separation which consequently increased the Hc of Cr-containing materials.

Jan 1, 1997

By John D. Smart, John W. Sager

The following paper is an evaluation of the instrumentation programs on recent Corps of Engineers tunneling projects. The authors have first-hand knowledge of the NORAD Cheyenne Mountain Complex (NCMC) Expansion Project. Information on the other projects comes from conversations with those directly involved in the instrumentation programs and from referenced reports. The specific objectives of this paper are: (1) to state the purposes of the instrumentation programs, (2) to discuss the benefits gained from the instrumentation, and (3) to present conclusions from this study that will provide guidance to those planning instrumentation on future projects. Presentation of detailed descriptions of the projects and instrumentation data is limited to that necessary to the accomplishment of the above objectives. NCMC EXPANSION PROJECT The NCMC is located at a depth of approximately 800 feet in Cheyenne Mountain near Colorado Springs, Colorado. For the current expansion project new chambers were mined to accommodate a new diesel power plant and associated cooling and air handling equipment. During 1971 some 55,000 yd3 of granite were mined through existing access tunnels for this expansion. A model of the new excavation is shown in Figure 1. The light shaded areas are new openings, and the dark areas are portions of the existing operating complex. The large chamber to the right is the power plant chamber and has a span of 67 ft, a height of 50 ft, and a length of 172 ft. The other large chamber on the lower level is the cooling tower chamber and has a span of 38 ft, a height of 45 ft and a length of 185 ft. The small chamber on the upper level has a span of 20 ft and is 27 ft high and 140 ft long. Other major excavations are the 18 ft diam air tunnel

Jan 1, 1997

By Terence G. McCusker, E. Roy Anderson

A four-mile length of interceptor sewer tunnel in Manhattan has finished sizes ranging from 10'6" to 14'6" horseshoe. Mixed face conditions were anticipated in three areas and encountered in five. All were short but since the tunnel lies well below the water table and failures would involve important utilities, major structures and human lives, great care had to be exercized in choosing a construc¬tion method. Chemical consolidation was selected as the best approach with compressed air working as a backup system. Initially grouting was accomplished from within the tunnel, but treatment from the surface was more successful and was later adopted. The soils consisted largely of impermeable weak silts and it was found possible to inhibit access of water to this material so that it could be controlled by breasting within the tunnel without loss of stability. It is concluded that in the interlayered permeable and impermeable soils encountered, chemical grouting would successfully stabilize the working face. INTRODUCTION An interceptor sewer is currently under construction along the entire length of the west side of Manhattan. When complete, the tunnel will intercept and divert to a treatment plant (also under construction) a daily flow in excess of 200 million gallons per day. About 9 miles of the interceptor sewer is in tunnel and the remain¬der is cut-and-cover construction. The tunnel is almost entirely in Manhattan schist but where its alignment crosses major faults at comparatively shallow depths, mixed face and earth conditions are

Jan 1, 1997

By F Hancock

A rainfall simulator was developed to assist with hydrogeomorphic research into the stability of engineered landforms associated with rehabilitated uranium mines in the Top End of Australia. It can be used in rough terrain with slope gradients up to 30o. The rainfall simulator is modular, utilises upward jetting nozzles, has a multiple head arrangement and is capable of delivering rainfall intensities between 60 and 300 mmh-1 over areas up to 1000 m2 and could be easily modified for larger areas. Rainfall uniformity is commonly in excess of 80 per cent and the kinetic energy approaches that of natural rainfall (The modular design utilises an equilateral triangular array of rainfall stands, constructed from galvanised steel water pipes and flexible plastic hoses. Total construction costs are low. The water supply reservoir is mobile and easily constructed. An example of its use at Ranger Uranium Mine, investigating the effect of cover on rainsplash and rainwash dominated processes shows that vegetation cover is likely to reduce the erosion rate by these processes by at least four times below that experienced on bare areas.

Jan 1, 1997

By Martin Oatman, Lawrence Lenahan

The West Seattle Tunnel is part of a regional sewer conveyance system located in Seattle Washington. The tunnel was constructed for the Waste Water Treatment Division of the King County Department Of Natural Resources, from June of 1995 through the first quarter of 1997. The Geologic setting for this soft-ground tunnel consists of glacial, interglacial, glacio-lacustrine, and alluvial soils. This paper, prepared jointly by the owner and con-tractor, will describe project-related site geology, engineering considerations, construction, and dispute resolution/avoidance practices.

Jan 1, 1997

By William H. Snyer, Victor A. Sterner

A cache of buried explosives was discovered by ICI Explosives, USA Inc. at one of their sites near Gillette, Wyoming. An intensive investigation conducted by ICI management indicated that nitroglycerin sensitized dynamite might be present. Information also indicated that up to 20,000 pounds of explosives may have been buried.

Jan 1, 1997

By Harry Sutcliffe

INTRODUCTION The need for discussion of Owner-Engineer-Contractor relationships in tunneling arises from the increase in costly and time-consuming litigation. The paper examines the objectives, motivations and responsibilities of each party, discusses some common causes of claims in underground work, and makes some suggestions for improvements. The viewpoint and bias are those of an engineer. If a subtitle were required for the session, "Sharing the Risk" would be appropriate. Sharing the risk is an important aspect of Owner-Engineer-Contractor relationships because when a risk is shared, all parties have an incentive to minimize it. The System It would be shortsighted not to recognize that the system is wider than the Owner, the Engineer and the Contractor. There are many outside influences which affect the day-to-day behavior of each party: Financing agencies Insurance agencies Bonding agencies OSHA and other safety legislation The Federal Power Commission The Public Utilities Commission The General Accounting Office

Jan 1, 1997

If a fire occurs outby an underground coal mine section, the immediate safe evacuation of miners from the working section should always take precedence. Unfortunately, in many cases, the dedicated escapeways (escape routes) for the evacuation of the miners become contaminated by the byproducts of fire from the adjacent entries. The purpose of this paper is to present the ventilation-control process that would keep the escapeway free from contaminants and, thus, available for travel. A few scenarios of mine fires in longwall development panels are analyzed and discussed. To perform these studies, a mine fire simulator (MFS) was used. This (MFS) provides a dynamic representation of the fire's progress (in real time) and gives a color-graphic visualization of the spread of oxygen, combustion products and temperature of the gases throughout the ventilation system. Also presented and discussed are ways in which the MFS can be used as a training and teaching tool for miners and, particularly, for ventilation and safety specialists.

Jan 1, 1997

With the introduction of the Health and Safety in Employment (HSE) Act 1992 and the subsequent repeal of regulations pertaining to mining, there has been an upheaval of the management of health and safety in mines.  More than ever, employers know that they must ensure that their workers are competent to carry out their assigned tasks.

Jan 1, 1997

By Giovanni Toniatti

Brazil is a country with continental dimensions. It hosts many different varieties of terranes and geological environments in its 8.5 million km2 (3.28 million sq miles). This mineral endowment has been important for the country's economic and social development process since the early colonial period, leaving Brazil with a legacy of almost 400 years of mining tradition. Mining in Brazil started in the early 17th century with diamond and gold discoveries. The made the country the leading producer of both for more than a century. This phase faded by the late 18th century when the alluvial deposits were depleted. It finally yielded to competing countries where technology and capital were being applied more efficiently. This period of mining dormancy lasted from the late 19th century until the first decades of the 20th century when Brazilian mining picked up. There was growing pressure on mineral resources by the affluence of the industrial society. The fast-growing demand resulting from the two world wars had brought the Brazilian mineral wealth back to the scene. This second Brazilian mineral boom made the country a leading producer of iron and manganese ore, quartz crystals and other strategic minerals. This expansion in Brazil's mining industry provided the basis for the country's industrialization process. This was led by the Brazilian steel and petroleum industries. Unfortunately, the thrust provided by this modern industrial basis was not properly used as a lever for further industrial development. The upstream industrialization process was not supported by the proper development of the raw materials supplying basis. The resulting industrial model was heavily dependent on imports of raw materials. It did not support the economic growth and faced fierce industrial competitiveness and sophistication that emerged with the postwar economic boom.

Jan 1, 1997

By R. W. Mossman, George E. Heim

Seismic exploration techniques offer the engineer and geologist a way of obtaining detailed information on the physical parameters and geometry of the rocks where extensive underground excavation or tunneling is proposed. Use of the seismic method can provide a greater amount of detailed information at relatively less cost than can be obtained by any other known subsurface exploration method. Boreholes are still required for calibration of the seismic data but at a much wider geographic spacing than otherwise would be needed for subsurface mapping. The seismic data can define with precision the actual location of zones of flexure or fracture of the rocks and reveal the configuration of the surface of the rock layers. ENGINEERING PROBLEMS One of the major requirements in the planning of subsurface installations is that of locating tunnels and other underground openings in favorable rock units. Such rock units should exhibit uniformity of composition, both vertically and horizontally, to minimize variation in excavation techniques. The depth and thickness of the unit must be known: a 30-foot diameter tunnel cannot be contained in a 25-foot thick limestone. The rock unit needs to be as free as possible from structural defects and should be suited to efficient excavation procedures. If liquid conduits are planned, the slope of the rock unit needs to be known so that maximum advantage can be taken of gravity flow with the tunnels wholly contained within the unit.

Jan 1, 1997

By Viggo C. Bertelsen, David G. Hammond

LOCATION AND EXTENT OF BART TUNNELS The San Francisco Bay Area Rapid Transit District (BART) during the past six years has become the Owner of 23.5 miles of single-bore tunnels. The tunneling experience gained while working closely with our Engineer and Contractors in the design and construction of these major transit facilities provides a basis for our "Owners" viewpoint. The 23.5 miles of tunnels are divided into two categories. Fifteen and one-half (15-1/2) miles of tunnels were constructed in soft ground underlaying the downtown areas of San Francisco, Oakland and Berkeley. Eight (8) miles of tunnels were built in "hard ground" in the hills separating Oakland and Berkeley from Contra Costa County and in the San Francisco hills on the Mission Line. Location of tunnels within the BART system are shown on Figure 1. The tunnels comprise 15.7% of BART's 75-mile dual track system. Their 176 million dollar costs (excluding rail, electrification or ventilation features) are 12.4% of the system's total estimated cost of $1.4 billion. The tunnels constructed in soft ground were shield and boring machine driven with ground support provided by steel liner rings. The exterior diameter is 17 foot, 6 inches in the majority of tunnels; however, on two tunnels with a 500 foot radius of curvature, the diameter was 18 feet. BART awarded 14 contracts for soft ground tunneling. The work was accomplished under free air or compressed air depending upon the ground water and soil conditions, safety requirements, and considerations for protecting adjoining property from damage either from the de-watering operations or settlements due to excavation. The tunnel bores, except on curves, were normally parallel being spaced at 32 foot centers on the Mission

Jan 1, 1997

By Kenneth L. Johnson

The effects of underground longwall coal mining on flow in perennial streams within the Pittsburgh seam basin were evaluated. Four streams above four different longwall mines were studied. Overburden depths at the study sites ranged from 500 to 600 feet. At all four locations, premining streamfow measurements were made to establish baseline flow conditions. Measurements were then repeated at each location after the longwall face passed beneath the stream. At one location, in which the longwall panel axis was roughly parallel to the stream, the streamflow was monitored as the longwall face advanced. Measurements at this location showed that temporary flow reduction occurred as the face advanced underneath; however, after the tensile portion of the traveling subsidence profile passed, this effect was lessened. At two of the sites in which the stream was roughly perpendicular to the panel axis, postmining streamfow increased across the panel and decreased over the development headings, such that the net lateral change in streamflow across the fully subsided panel and associated development headings was small compared to the measured flow.

Jan 1, 1997

Batterham and Algie began their paper on: `The role of technology in the minerals industry' (1995) by noting that while: it is often stated that innovation is central to the economic survival of mining and minerals processing in the face of global competition, .. . technology is often far from a core strategy in our industry. This point is correct. Throughout the world, as a broad generalisation, mining companies do not value technology development as a principal means of gaining competitive advantage. It is important to understand why this is the case. Batterham and Algie address this question by making distinctions between innovation, technology and research. They note that while: all successful (mining) companies are good at innovation . . . that innovation can proceed without any research and development and that it is innovation that generates the competitive advantage, not research and development per se. In this paper we accept these arguments. However, our focus is somewhat different. Whereas Batterham and Algie took a mining company's perspective on the technologies of mining and processing, we take a broader view of the opportunities for technology development for company Australia but, in order to focus the argument, we restrict our discussion to the area of mining (rather than processing); we focus particularly on mining systems and mining equipment. We begin by looking at the motivation of companies operating in any industrial sector to invest in research and development. Figure 1 recognises four levels of industrial maturity. For companies in the embryonic and growth stages R&D often is essential to initiating and developing the business. Mining, on the other hand, is a mature industry. In mature industries the conventional roles for R&D are to reduce costs, to extend product differentiation, or to develop new technology with the aim of rejuvenating the business. Next we ask whether these general-industry arguments apply to the mining industry. If they do then the mining industry should value R&D more highly; after all cost reductions and business rejuvenation are goals that are worth achieving. On the other hand if, for whatever reason, these general arguments do not apply to mining then this may lead the mining industry to invest only modestly, or not at all, in R&D. In this event, while this may be a rational decision for the mining industry, it may not be in the best interest of a nation like Australia where revenues from the sale of mineral products represent an important part of the country's economy.

Jan 1, 1997

By J. Y. Kim, S. L. Chryssoulis

Lead ions that originate from galena during the processing of complex sulfide ores migrate onto the surfaces of sphalerite and iron sulfide minerals. This results in poor selectivity during differential flotation. Generally, in sulfide ore processing, the lead-activated minerals float in the Cu/Pb rougher circuit. The surface lead complicates the zinc flotation circuit by lowering the concentrate grade. The effect of lead in the differential flotation of sphalerite from Cu-Pb-Zu and Pb-Zu ores is discussed. Plant and laboratory-test data are interpreted by determining the surface compositions of individual grains of sphalerite and iron sulfide particles. For the first time, surface compositions were determined by using laser-ionization mass spectrometry (LIMS) and time-of-flight secondary ion mass spectrometry (TOF-SIMS). Cationic and cationic species on the surface were analyzed to elucidate the phenomena. It was proven that these new techniques are very useful in understanding the basic mechanisms of a sulfide mineral-flotation system.

Jan 1, 1997

By Leo L. Van Sambeek

Specification of properly sized pillars to support the overburden is one of the most challenging aspects of salt mine design. Interest in salt pillar design is heightened by the recent flooding of the Retsof salt mine, water inflows to the K2 potash mine, and closing of the Belle Isle salt mine because of ground control problems. A series of numerical modeling analyses show that a simple pillar design equation for salt pillars adequately reproduces results of extensive modeling efforts. The paper describes (1) the basis for the pillar design equation, (2) equation verification by comparison with numerical modeling results, and (3) equation validation by comparison with measurements and observations of salt pillar behavior.

Jan 1, 1997