Search Documents

By J. R. Rendón

Cylinders of commercial aluminium alloy 6063 were homogenized under different conditions. The experimental results indicated that the general mechanical behaviour as related to curves of 0.2% yield strength, ultimate tensile strength and Brunnell hardness versus homogeneizing process is the same in both cases. The mechanical properties as compared to those required by plant specifications, tend to be better with increasing values of % Mg2Si in the alloy, as expected. The electron microscopy investigations revealed that in both homogeneizing processes the resulting microstructure consist of significant spheroidizing of the alpha phase (AlFeSi) and fine-needle type structure of beta phase. The alpha phase was also present in a Chinese type scripture. Furthermore, the slow cooling within the furnace resulted in the nucleation and growth of Mg2Si precipitates generally along the grain boundaries.

Jan 1, 1997

By R. J. Sweigard

Fine coal refuse is often pumped, as slurry, into surface impoundments as a means of permanent disposal. As the available volume is filled, the height of the embankments are frequently increased. Many times the additional embankment material is placed upon consolidated fine coal refuse. There has been some concern about the long-term effect of consolidation of this material at or above the liquid limit upon its shear strength. A laboratory investigation was performed using three different types of fine coal slurry taken from Central Appalachian coal preparation plants. The refuse was consolidated in 10-foot plexiglass columns under incremental amounts of surcharge loading. The incremental loads were designed to simulate the effect of increasing the height of a refuse embankment on top of the consolidating coal slurry. After the refuse in the columns had consolidated for several months, the columns were cut apart and triaxial tests were performed on both the consolidated material and unconsolidated material for comparison of their shear strength parameters.

Jan 1, 1997

By Cooke D, Large R

The Cambrian structure in the Mt Read Volcanics was produced by four deformational events: obduction of forearc-derived mafic/ultramalic complexes in the early Middle Cambrian, a middle Middle Cambrian extensional phase related to the post-collisional Mt Read volcanism and VHMS mineralisation, Middle Cambrian E-W folding, and Late Cambrian N-S folding and basin inversion. The major phase of VHMS mineralisation in western Tasmania is restricted to the very brief period of extensional tectonics within the middle Middle Cambrian. Within this period a N-S graben was produced with a complex series of transfer zones, largely striking E-W. Most VHMS mineralisation is restricted to the top of massive volcanic successions, with several mines close to Cambrian transfer structures. Many of the transfer structures continued to be active until the Devonian. The later compressional Cambrian events are not significant in localising orc formation. Within the Rosebery mine a complex pattern of minor Cambrian normal faults has a second order control on the distribution of the mineralisation.

Jan 1, 1997

By Terry Owen

Business development process. Throughout Cyprus Amax's early months in Russia, the company stayed focused on what was needed from a deposit for economic success. Cyprus Amax's reason for success in Russia is that all involved - its Russian partners, the workforce and expatriates - provided a focused effort that served the project as it worked through the tender process and the Russian regulations. The company developed an understanding of the regulatory process by working with solid, ethical partners. Infused into the Kubaka management structure were Russians with the knowledge to facilitate the process and a professional group of expatriates. Developing credibility and a solid rapport with the Russian mining authority was critical to the success of this venture. Identifying and gaining the trust of key Russian individuals was also critical during the early stages. Gaining their trust and building credibility was part of the process. These key Russians were brought to the United States to visit existing Cyprus Amax mines. These efforts proved valuable in building an understanding with the Russians about the kind of company Cyprus Amax is and the kind of efficient operations that it can run. This was a learning process for all parties. Fortunately, the company was dealing with intelligent and educated people.

Jan 1, 1997

By Thomas M. Keevin, Gregory L. Hempen, David J. Schaeffer, John M. Jr Pitlo

Repelling charges are small explosive charges detonated to frighten and drive fish away from a blasting zone just prior to detonation of a major explosive charge. Use of repelling charges has been recommended by natural resource agencies to mitigate the effects of submerged explosives. Blasting companies have used this technique in a "good faith effort" to reduce potential damages to aquatic resources. It has been assumed that noise or pressure generated by the small charge will drive fish from the immediate area, thereby reducing impacts from the much larger and potentially more-damaging blast.

Jan 1, 1997

By H. Hinds

Plant testing of DuPont's Activator Technology in the vat leach circuit of the Homestake mine shows increased gold recoveries of 3-5%. Activators are catalysts of gold dissolution in cyanide solution. DuPont received the patent for this technology in January, 1996. The test was run in the west sand plant alternating control and activated vats to reduce the variability in head grade and cyanide consumption. Activated vats had gold in the preg solutions earlier, higher gold recovery, and lower gold residuals. Activator addition did not adversely affect mill operations or the environment. Optimization of the technology continues.

Jan 1, 1997

By Smele J. S, Dawes W. D

In recent years there has been a trend among mining companies to diversify exploration and development away from the countries that have dominated mining activity for the latter half of this century. With some exceptions, this trend is accelerating and is a function of the recognition that many parts of the world, with no previous exposure to modern exploration, are endowed with considerable mineral potential. In addition coincident with changing political and economic circumstances, many countries have recognised the benefits of attracting international mining investment and have radically changed policies, fiscal and legal regimes so as to encourage exploration and mining. Some countries, however, have not readily accepted mining for cultural or social reasons and have yet to make effective changes to mining legislation. For historical reasons, other countries may have little or no direct experience of western economics, nor may they fully recognise the need for stability and competitive fiscal and legal systems to attract foreign investment. Not all ventures in new countries have been commercial successes and there have been some lamentable and recent lapses from grace. Company strategies, company standards and management objectives can also vary widely from company to company. What may be an acceptable risk or rate of return for one may be completely

Jan 1, 1997

By John A. Herbst

At the last Comminution Symposium a challenge (Meloy and Williams, 1992) was issued to "predict the typical straight-line, self similar" tumbling mill product size distributions using a population balance model (PBM). Implicit in this challenge is the assumption that the PBM is inadequate for predicting real world grinding performance. This response is presented in three parts: I. Theoretical analysis of the general PBM and its appropriateness for comminution system modeling. II. Examination of the accuracy of prediction of real world milling behavior using linear and nonlinear PBMs. III. Evidence from recent microscale comminution research. This paper concludes with recommendations concerning future research which will: 1. further elucidate mechanisms of particle destruction and creation as well as attrition and 2. increase the accuracy of model predictions in highly nonlinear situations

Jan 1, 1997

By Marcel Haffen, Jean Janin

The purpose of grouting is to modify the permeability and strength characteristics of the subsoil in such a way that the planned structure can be efficiently constructed at a given location. This technique, which originally underwent considerable development in the field of dams construction is constantly evolving and it becomes more and more important in urban zones of intensive underground development for projects such as transport tunnels, stations, car parks, ect. Grouting becomes more and more indispensable whatever the natural characteristics of that subsoil ; such is the case particularly when the planned work runs through cohesionless granular soils, usually water-bearing such as alluvium, sands, disturbed ground, fill material, etc. The selection of the grouting method and the extent of treatment required at depends on two fundamental factors. 1º) nature and behaviour of subsoil to be treated. There is no need to stress the necessary of a good knowledge of geotechnical, hydrological and chemical characteristics of the ground to be treated. At the present time the specialists in these fields have available numerous methods of analysis, either laboratory or field tests, which enable to evolve a suitable treatment.

Jan 1, 1997

By G. Ramadorai

"This paper addresses processing options for recovering gold from carbonaceous sulfidic gold ores. These include, but not limited, to the following methods: (1) Hypochlorite pretreatment followed by cyanidization; (2) Chemical blanking agents pre-treatment followed by cyanidization; (3) Non-cyanide heap leaching techniques; (4) biological pre-treatment followed by cyanidization; (5) biological pre-treatment followed by non cyanide heap leaching. Issues of costs, economics, recoveries, testing methods, state of advancement etc., will be discussed in the paper.ABSTRACT ONLY"

Jan 1, 1997

By D. Forbes

The results of a fundamental study involving zeta-potential and turbidity determinations of solid suspensions are discussed. Illustrations of how these results are utilized to design field applications of solid-grade polymers to clarify mine-drainage water are presented. Operational and economical advantages are examined.

Jan 1, 1997

By Osvaldo A. Bascur

Most mining and metallurgical plants have developed predictive maintenance policies based on statistical analysis and special techniques, like vibration analysis, oil and lube analysis for critical equipment. Process control strategies have also been installed in several metallurgical sites. These control strategies require instrumentation maintenance from local personnel. The availability of real time and process history to identify the most critical part of the processing system from mechanical integrity is a must for global plant optimization. Specialized performance control monitoring algorithms are required to justify their existence and contribution to the bottom line. Emerging technologies are combining these techniques into a single total plant system. Tools are required to assist in troubleshooting and adapting these process control instruments and strategies. The key is the plant equipment and process control availability and utilization rather than just maintenance.

Jan 1, 1997

By M. Bidart, V. Sawyer, M. Saunders Macdonald

A number of open pit gold mines in Nevada extract ore from areas that are below the natural groundwater elevations. This necessitates dewatering, which requires a method for the disposal of the extracted water. Some of these open pits extend well below, the water table with dewatering volumes greater than 10,000 gpm (38,000 L/min). Some mines with large volumes of dewatering water have constructed reinfiltration basins to reintroduce the water into the groundwater system at a point some distance from the pits. This paper presents an overview of the state of the art of reinfiltration projects, including the permit process for such projects in Nevada. The paper includes the necessary engineering considerations.

Jan 1, 1997

By Yunsheng Yao, P. Golledge, A. D. S. Gillies

In order to investigate the explosibility of sulphide mineral dusts, sulphide ore samples were collected from five underground metalliferous mines in Australia. The mineralogical and chemical composition of the dust samples was analysed by X-Ray Powder Diffraction and Atomic Absorption techniques. Simulated post detonation fumes were produced and used in dust explosibility tests to examine the influence of the fumes on sulphide dust ex- plosions. These tests were conducted in a 20 Litre Siwek Explosion Chamber with measurement and control system that is regarded as a standard testing system worldwide for dust explosion studies. The dust mineralogical composition and dust explosibility tests indicated that the content of sulphur can not accurately predict the explosibity of the sulphide dust. The percentage content of pyrite in the sulphide dust can be a relatively reliable diagnostic criterion in evaluating the risk of sulphide dust explosions in the mining of a massive sulphide orebody. The hybrid explosion tests demonstrated that the post detonation fumes from ANFO not only decrease the lower explosion limit of the sulphide dusts, but also increase the severity of the dust explosions. The explosion pressure reaches its peak value when the fumes content in the explosion chamber is about 20 per cent by volume

Jan 1, 1997

By William J. Wiehagen

This is the third in a series of four articles that discuss underground fire-fighting preparedness. As with the first two articles, it is based on interviews with 214 miners conducted at 7 underground coal mines (referred to as Mines ?A? through ?G?) by researchers of the National Institute for Occupational Safety and Health?s (NIOSH) Pittsburgh Research Center [Vaught et al. 1996]. In the first article, the authors presented an overview of the study conducted by NIOSH on mine fire response preparedness and provided a general perspective on underground mine fires. The second article discussed miners? preparedness to evacuate a fire and their experience with incipient fires. In this article, we describe miners? experience in fighting underground mine fires and present their perceptions of training and readiness for fire-fighting.

Jan 1, 1997

By Y. F. Vasyuchkov

In general a term "unconventional mining or "non-traditional mining technology" getting more and more familiar to the mining engineering media. There are several alternating terminological combinations such as "in situ mining", "borehole mining", "shaftless mining", "mineless mining", "geotechnology" etc.; specific terms denote particular method of unconventional mining technology: "underground coal gasification in situ", "underground coal combustion in situ", "borehole hydraulic coal mining" and others. Principal scheme of unconventional coal mining technology is shown in Figure I:

Jan 1, 1997

By Stephen G. Hardcastle

CANMET has developed a simple yet very effective tracer gas method to test the efficiency of stench gas emergency warning systems which can easily be performed by mine personnel. This test method uses sulphur hexafluoride (SF,) as a surrogate for such stench gases as ethyl mercaptan. The test has many advantages: it is non-disruptive to production because SF, is odourless, colourless; it is safe to use as it is inert and only a small volume, insufficient to reduce oxygen levels, is necessary to dope the air with a measurable concentration; and most importantly it provides definitive results to assess the adequacy of the warning system. Specific findings of these tests have included, over doping sections of the mine and subsequent production loss due to sickness, the warning being ignored, the injection period being too short, excessive dispersion, and inadequate notification times. The simple test protocol involves releasing a known volume of the SF, under similar circumstances to those of the stench gas, and then sampling for its presence downstream. These samples are collected in air-tight syringes which are then analyzed in a laboratory with a gas chromatograph. By direct proportion, between the size of the stench and tracer gas releases, it is possible to convert the SF, concentration into equivalent stench gas concentrations profiles. From these, it is possible to define, the initial arrival time of the gas, the time it takes to reach a "target" notification concentration, whether the gas peak will exceed TWAEV, STEV and CEV exposure limits, and the duration of the peak above these levels. Since 1993, this test protocol has been employed a total of eight times on four different Canadian mine properties and the results are being used to optimize the stench gas release system with respect to volume of gas used, duration of injection, and number of injection locations.

Jan 1, 1997

By M. C. Bétournay, J. E. Udd

"The legacy of abandoned mines in Canada creates issues that impact on both the health and safety of Canadians and the environment. Solutions to the problems of abandoned minesites require a detailed understanding of site conditions, the engineering solutions which may be relevant, and planning for effective use of the land. In this paper, the authors outline the basic thrusts that have been developed at CANMET to address this problem. These include: multiprovincial agreements to develop a national database; methods of site rendering; a ten-year research program to develop engineering approaches; the review of a large number of case studies; and outlining the associated risks. Examples of the applications of this research are provided in the areas of: municipal, provincial, and federal co-operative projects; site-specific applications; and international linkages."

Jan 1, 1997

The gold concentration profiles which develop inside the activated carbon particles during the adsorption process were measured, so as to obtain additional direct proof of intra-particle mass transfer rate-control and to determine how individual carbon particles in a population vary in their gold uptake behaviour. The observed gold concentration profiles inside the activated carbon particles were typical of situations where an intra-particle mass transfer mechanism is rate-controlling. Gold di-cyanide penetrated the carbon particles with a wave-like front until it was uniformly distributed throughout the particle. This corresponds with the profiles predicted by the film and surface diffusion model. However, the rate with which gold di-cyanide was transported inside the individual carbon particles varied within the population of carbon particles. This variation was characterized by a lognormal distribution in surface diffusivity. Because the estimated variances of these surface diffusivity distributions were small, the dynamic adsorption behaviour of the carbons used in the present study did not deviate significantly from that predicted by a model based on film mass transfer and a single surface diffusivity. Van Deventer (1984, 1985 and 1986a) reported data that could not be adequately described by a model based on film mass transfer and a single surface diffusivity. In this study a model based on film mass transfer and a wide lognormal distribution of surface diffusivity values was applied to his data. It was shown that a population of carbon particles with a wide distribution in surface diffusivity values could offer an alternative explanation to the mechanism proposed by Van Deventer which was based on film mass transfer, with partitioning of the carbon into micro- and macropores with surface diffusion in the macropores and slow mass transfer into the micropores.

Jan 1, 1997

By Murray Gamble

A new type of groundwater cutoff wall has been developed at the University of Waterloo. The Waterloo Barrier? is a steel sheet piling system that incorporates a sealable cavity at each interlocking joint. In order to prevent leakage through the joints, the sealable cavity is flushed clean and injected with sealant after the installation of the piling. The installation and sealing procedures of the Waterloo Barrier? system allow for a high degree of quality control resulting in a very low permeability cutoff wall. Based upon field installations, the bulk wall hydraulic conductivity of the Waterloo Barrier? ranges from 10-8 to 10-10 cm/sec. Recent case histories are presented in which Waterloo Barrier? vertical cutoff walls have been used to prevent the off-site migration of contaminated groundwater or soil gases. In some instances, the Waterloo Barrier? system was used in combinations of applications such as preventing the migration of contaminants, redirecting the flow of groundwater, providing structural shoring for soil excavation and aiding in site de-watering processes.

Jan 1, 1997