Search Documents

By Walter Nuñez

El presente texto describe el modelamiento y cubicación en las vetas como elementos del software que asiste a topógrafos, geólogos e ingenieros de mina en la operación diaria de la mina. El modelamiento geológico, es el conocimiento de la geometría espacial del depósito, y la cubicación de reservas minerales, determina la cantidad del mineral y la ley que existe en el depósito a largo plazo, constituyéndose en dos prerrogativas de las que dependerá el éxito y futuro de una empresa minera. Sin embargo, el inconveniente es que estos paquetes están diseñados para ser aplicados en minería superficial, más no a en minería subterránea, donde se debe adecuar la data para su buen uso. Por ello, se presenta un diagrama en el que se muestran las diferentes actividades y el flujo de información que se sigue para llegar a modelar y cubicar uno de los clavos de la veta Consuelo.

May 25, 1998

By Raúl Castellanos

Las herramientas de modelamiento empresarial fueron diseñadas para apoyar la gestión estratégica de las empresas mineras con el objetivo de especular sobre lo sucedido con las organizaciones. En ese sentido, el presente texto señala un modelo personalizado que se ajuste a la empresa. Es decir, donde la principal función del modelador sea la “simulación”, la cual permita elegir con un menor margen de incertidumbre, la estrategia más conveniente o más rentable, aunque se complique con un número mayor de variables.

May 25, 1998

By Sashir Estela De la Cruz

Actualmente la informática como herramienta aplicada al sector minero nacional, es importante -en tanto su empleo adecuado y racional implica alcanzar los objetivos planteados en forma más rápida y con mayor calidad. En este sentido, el presente texto describe el sistema informático que genera soporte al trabajo de modelamiento geológico para la estimación de reservas mineras, de forma que reduce el tiempo y personal empleado en dicha labor. Este sistema se divide en dos partes: estadístico y gráfico y determina la explotación de un prospecto de yacimiento minero.

May 25, 1998

By Carl Verholek

Remote control systems for industrial applications have advanced since the early 20 years, increasing its capabilities by utilizing new electronic technology. This electronic “tool” has benefited many mining operations, making them a safer place to work and at the same time more productive. Almost any operation that presently uses a man at the controls of the machine or using a wired tether control, is a candidate for improvement by the addition of a remote control. Remote control systems add safety, reliability and productivity at a cost that is usually recovered in mere months after installation.

May 25, 1998

By Carlos R. Scherpenisse

La voladura es una de las operaciones unitarias en la extracción del mineral, donde se busca un adecuado grado de fragmentación de la roca y se reduzca el costo combinado de las operaciones de perforación, voladura, transporte y chancado primario roca, produciendo a la vez el menor daño posible en las cercanías de ésta. En este sentido, el empleo adecuado del Monitoreo de Vibraciones producto de voladuras, es una técnica que provee múltiples ventajas en términos de examinar en detalle el proceso de la voladura y conocer su eficiencia relativa, su interacción con las cargas adyacentes y en definitiva el rendimiento general del diseño. Por ello, el presente trabajo describe algunos casos de aplicación de la técnica de monitoreo de vibraciones -particularmente en Mina Subterránea y su importancia en el diagnóstico, control, modelamiento y optimización del proceso de la voladura. Asimismo, analiza su potencial en términos de alcanzar substantivas mejoras técnico-económicas, aumentar los rendimientos y minimizar los costos operacionales en esta etapa de la explotación minera.

May 25, 1998

By Manuel Sanchéz

Para las empresas mineras, la búsqueda de buenas condiciones con los clientes y la optimización de los procesos involucrados en la cadena de valor, es uno de sus principales objetivos. En este sentido, el presente texto señala las estrategias y soluciones que priorizen y mejore la calidad de las decisiones en la empresa.

May 25, 1998

Objective: To evaluate the quantity of ventilation air reaching the face of a 40-ft box cut during a 40-ft, two-pass, extended cut and to examine ways to increase this quantity of air.

May 1, 1998

Objective: To develop and test a training program that enhances the hazard recognition skills of underground limestone miners. This program can help job performance and lead to enhanced safety in the underground workplace.

May 1, 1998

By Barbara J. Halpern

There?s no denying that mining is a male-dominated industry. Yet thanks to technologies developed over the last 20 years, societal changes in sex role stereotyping, individual determi­nation, and the willingness of companies to train women, there are no jobs in mining today where women are not represented. Women are drillers and electricians as well as drivers of heavy equipment and haulpack trucks. They perform jobs ranging from field exploration and metallurgy to clerical and janitorial and warehousing positions, from prospectors and underground blasters to geologists and land reclamation experts, from communicators to legal experts on mining law and more. The Women?s Mining Coalition, founded in 1994 to shepherd responsible legislative mining reform, estimates that 20 percent of the workers in the mining industry are women. Although women are concentrated in clerical and adminis­trative jobs, at least 10 percent are in non-traditional, hardhat jobs, claims the group. There are women in management, but the numbers in senior management remain small, especially in larger companies.

Feb 1, 1998

Objective Develop field measurement and computer modeling methods to predict the potential for hang-ups and structural failures in underground mine ore paws. Background Analysis of Mine Safety and Health Administration (MSHA) accident statistics has identified ore pass hazards as a significant safety problem in underground metal mines in the United Stales. Recent ore pass failures have underlined the lack or ore pass design methods ant1 standards available to both MSHA and mine engineers. Injury and fatality data for the 20-ycar period between 1975 and 1095 show that nearly 75% of the injuries were directly or indirectly related to pulling or freeing ore pass chutes, the use of hand tools, falls or broken rock, and structural failures or chutes or gates and ore pass walls.

Feb 1, 1998

Objective Develop a method to warn of hazardous conditions and enhance safety during operation and inspection of vertical mine shafts and hoists. Background Mine hoisting is the most critical and potentially the most dan¬gerous operation in underground mining. Many hazards are related to falls of miners and materials, ground instability, and malfunction or lack of safety devices. All have the potential to cause a cata¬strophic accident. A condition known as "slack rope" is particularly dangerous, expecially if it occurs without the operator's awareness. The most common occurrence of slack rope is in metal or nonmetal mines that have a history of ground control problems near the "haft. Approach Studies of hoist safety features and Mine Safely a and Heath Administration (MSHA) accident statistics suggests a need to measure wire rope tension, conveyance speed and position, and shaft guide misalignment. The most accurate data are obtained directly from the conveyance. Such data could warn of potentially dangerous situations during hoisting operations, as well as during inspections, maintenance, and lowering of large equipment. Figure I shows the concept for monitoring wire rope tension, conveyance position, and guide displacement. Progress to Date A conveyance-mounted system has been developed that monitors rope tension: hoist conveyance position, speed, and load; and shaft guide misalignment. A "flex-beam" load sensor mounted just above the- conveyance protects against slack and tight rope. The measurements are transmitted 60 times a second via wireless equipment from the conveyance to the hoist room. An encoder mounted on the conveyance eliminates the need to correct the position because of rope stretch. Figure 2 shows the encoder wheel and guide displacement sensors being mounted on a cage in¬spection deck. A potentiometer monitors misalignment of the shaft guides during inspections. Information about the cage or skip can be acquired by the shaft inspector using a hand-held indicator. Inspection can also he conducted remotely from a station or hoist room using the wireless link to a laptop computer. Figure 3 shows test results from a simulated slack rope condition. Patent Status NIOSH has a patent pending on this device entitled "Cable-Load¬Sensing Device." For More Information NIOSH is seeking cooperators to assist in further tests of this technology to improve hoisting safety. Additional information can he obtained by contacting Michael J. Beus, Steven Iverson, or Elaine Cullen, Technology Transfer Officer, NIOSH, Spokane Research Laboratory, Spokane, WA 99207 at (509) 354-8000.

Feb 1, 1998

By Fathi Habashi

This Historical Metallurgy Note is the final part of a three-part series, the first two of which appeared in the November- December, 1997 and January, 1998 issues of the Bulletin. This series of articles is dedicated to the memory of Nikolai Maximovitch Pereskuryakov (1940- 1994), Rector of Saint Petersburg Mining Institute from 1992 to 1994 who passed away unexpectedly at the age of 54, shortly after celebrating the 275th Anniversary of the Institute.

Feb 1, 1998

By John J. Sammarco

The mining industry has the highest average annual fatality rate among major U.S. industries. To address this, the National Institute for Occupational Safety and Health, Pittsburgh Research Laboratory (PRL), is conducting major research programs to reduce the hazard exposure of miners. One of the recently concluded programs at PRL developed the enabling technology for remote-controlled mining. An application involves the manual process of extracting and hauling coal where operators, in the tight confines of a mine, can be struck or caught by mobile machinery. The approach to remedy this problem uses a guidance system on the continuous haulage equipment so that it follows the continuous mining machine that extracts coal. This, in essence, involves sensor-based docking of the machines. Sensors functioning in the hostile mine environment of dust, methane gas, and water play the key role. Computer analysis of the mining machine's movements and empirical machine characterizations established operating requirements and spatial limitations to ensure proper loading of coal into the haulage equipment. These data served in the selection of a guidance sensor. Technologies such as scanning laser systems and ultrasonic sensors have frequently been used in other applications, but were found unacceptable. However, a near-infrared sensor employing active targets met the requirements. The sensor has a nominal 75b conical field of view and a range from 0.1 to 18.0 m. For the single-target mode, nominal range accuracy was 4.3% at a distance of 3.65 m. Correction algorithms were generated, which reduced the error to 0.6%. Airborne dust testing showed less than an additional0.8% accuracy (worst case) degradation at dust levels up to 15 mg/m3. Using four targets, the nominal range accuracy was 0.4% without correction algorithms. Analysis of dynamic testing of a continuous miner and haulage showed that accuracy was maintained and total target loss did not occur. A guidance system for the haulage system to follow the mining machine does not exist commercially. Such a system can reduce fatalities, injuries, and exposure to dust and noise.

Jan 11, 1998

By Steven J. Page, John A. Organiscak

Laboratory crushing experiments were conducted on a range of low- to high-volatile bituminous coals to investigate the various factors influencing airborne respirable dust (ARD) generation. This research was conducted to identify the principles of ARD liberation from the coal product. Five U.S. bituminous coals were uniformly prepared and processed through a double roll crusher located in a low-velocity wind tunnel. Experimental factors studied included inherent coal seam constituents, coal grind ability, specific energy of crushing, product size characteristics, dust cloud electrostatic field, and specific ARD generated. The results of this investigation indicate that a combination of several factors are associated with ARD generation. One factor is the effect of coal rank, described by the inherent moist fuel ratio, on the product size characteristics, defined by Schuhmann size function parameters. Another key factor is the effect of air dry loss(ADL) moisture in the coal seam on the breakage-induced electrostatic field of airborne dust. The effect of these factors is that different percentages of <10-m coal particles are dispersed as ARD. A discussion of electrostatic field principles, coal ADL, and its effect on ARD generation is presented.

Jan 10, 1998

By Anthony J. Miscoe, William M. McKewan, Richard C. Wang

The behavior of wire ropes used in hoisting is not well understood. In an effort to improve this understanding, the structure of round-strand wire ropes was analyzed. This report provides a generalized mathematical model that completely describes the geometry of the wires. It consists of two sets of vector equations and is valid for any round-strand wire rope. One set of equations is used to trace the paths of wires that have the form of a single helix; the other is used for the paths of double helical wires. The specific model for a 33-mm 6×19 Seale, independent wire rope core (IWRC), right regular lay wire rope was presented as an example. The paths and the geometric properties of the wires, which include the path length per lay of strand, the curvature, and the torsion, were determined from this model. The effects of strain deformation were analyzed, resulting in a system of equations for determining the structural parameters of the deformed rope. In future work, the model could be used to analyze wire ropes of different constructions so that a more scientifically based understanding of rope behavior can be established.

Jan 9, 1998

By Robert A. Cortese, Henry E. Perlee

Coal dust and float coal dust, produced during normal mining operations, in underground coal mines, are carried from the point of origin downstream by the ventilating air, where it deposits on the surfaces of the mine entry. In an explosion, this dust is lifted from the surfaces by the aerodynamic disturbances and, if of sufficient quantity, can continue to propagate the explosion. To prevent the surface coal dust from contributing, it must be inerted, typically by spreading pulverized limestone, i.e., rock dust, over the coal dust surface. To facilitate the dusting operation, the National Institute for Occupational Safety and Health (NIOSH), Pittsburgh Research Laboratory(PRL), developed an automated system that continuously monitors the accumulation of coal dust. This system could activate a rock-dusting machine that disperses rock dust into the ventilation air when dangerous deposits accumulate and deactivate the machine when sufficient inert has been deposited on top of the coal dust. The system consists of a microprocessor-controlled optical float dust deposition meter. This device measures the light intensity reflected from a deposited layer of dust. A standard cap lamp is used as a fixed-position light source. From the reflected light signal, the microprocessor determines the hazard level of the deposited layer and performs the appropriate action. Full-scale studies conducted in the Experimental Mine at PRL&apos;s Lake Lynn Laboratory, using alternating thin layers of rock dust and coal dust, successfully demonstrated the operation of the device. Based on the statistical data from these studies, a mathematical model was developed to predict long-term error in total rock dust content using this inerting procedure. Downwind dust dispersion was also examined to provide optimum placement of the dust sensors and to determine the need for better rock dust dispersion techniques.

Jan 5, 1998

The Upper Waimangaroa mining permit is part of the Buller Coalfield and lies on the eastern side of the Stockton-Denniston Plateau. The mining permit area is estimated to contain a total in-ground coal resource of 58 million tonnes, contained within 13 separate coal resource .blocks. The coal is Bituminous High Volatile B rank with export potential as semi soft coking or thermal coal. The Northern Opencast mine is the first mine proposed for Upper Waimangaroa and consists of the three resource blocks at the northern end of the permit area. The highwall of the mine will cut into the Mt William Range resulting in overburden cover of up to 150 metres in some areas. The ability to rehabilitate the area after mining was a major consideration in the design of the mine. The Northern Opencast area has been geologically mapped, extensively drilled and effectively modelled using Vulcan software. Three distinct coal seams are present and the mineable in situ resource is estimated at 8.7 million tonnes of which approximately 7.1 million tonnes is likely to be recoverable. It is proposed that this resource will be mined using opencast methods and the void will be backfilled with overburden. The life of the mine is at this stage estimated at 19 years based on an annual production of 500,000 tonnes at 1.8% sulphur and the Upper Waimangaroacoal will be blended with low sulphur coal from the Greymouth Coalfield to meet export specifications. The Northern Opencast area contains a range of native flora and fauna and physical features which make it an environmentally significant area. Mining will totally modify the area, thus an effective rehabilitation scheme is an integral part of the mine plan. Various rehabilitation methods will be used, and wherever possible, the backfilled areas will be rehabilitated so as to resemble the original area as closely as possible.

Jan 1, 1998

By Golab K, Partridge AC, Fletcher CAJ, Holtham P

Spiral concentrators are used globally in the fine coal processing industry to segregate particles, by gravitation, on the basis of density and size. Consisting of an open trough that twists vertically downwards about a central axis, a slurry mix of particles and water is fed to the top of the concentrator. Particles are then separated radially as they gravitate downward. Since their introduction to Australia in the 1940&apos;s, the generic design has evolved largely by laboratory trial-and-error investigations of different prototypes. However, this approach has proven expensive and optimal designs have not been necessarily developed. Accordingly, Computational Fluid Dynamics (CFD) analysis has been used recently as an alternative method of investigation, to assume as is envisaged, a role in the design process. To date, CFD models have progressed to simulations of turbulent fluid flow on current production spiral designs, and are continuing to be adapted for inclusion of particles at realistic feed concentrations. To be able to use the models confidently however, laboratory experiments must also be performed to validate the predictions during the development stage. This paper reports the current findings of an ongoing CFD and experimental program applied to one spiral unit. Satisfactory quantitative agreement has been achieved for the fluid and particulate flow characteristics, and although further validations are appropriate, the model already possesses significant potential for use as a reliable predictive design tool.

Jan 1, 1998

By Leigh Sharpe

Dunng the last 5 years a United Kingdom colliery has utilised a yielding-pillar configuration to extract a relatively thick coal seam at a depth of 640 m. As part of ongoing research into the siting of roadways adjacent to extracted longwall panels, seved field monitoring sites were established at differing locations to investigate roadway stability and yielding-pillar performance. Characteristic roadway deformation has been identified together with strata softening pathways which indicate the temporal increase in the height of softening into the roadway roof. In the assessment of such a complex problem numerical modelling, using FLAC, has been shown to contribute vital additional information, and provide further insights into the mechanisms controlling strata behaviour.

Jan 1, 1998

By R Frank Chiappeta, Eduardo Nixon, John Dean Smith, Tom Treleaven

"The creation of the Panama Canal was far more than a vast, unprecedented feat of engineering. It was a profoundly important historic event and a sweeping human drama not unlike that of war. Apart from wars, it represented the largest, most costly single effort ever before mounted anywhere on earth. It held the world's attention over a span of forty years. It affected the lives of tens of thousands of people at every level of society and of virtually every race and nationality. Great reputations were made and destroyed. For numbers of men and women it was the adventure of a lifetime.

Jan 1, 1998