Search Documents

By A M. Wala, H W. Wu

A research project incorporating a number of mine site exercises to reduce the effects of fire incidents and possible consequent health and safety hazards has been undertaken focused on the application of mine fire simulation software packages for contaminate tracing and fire modelling in coal and metalliferous mines. This paper examines aspects of introduction of inert gases to underground workings to aid recovery of a mine following a fire. Broad conclusions from work undertaken at individual Australian coal mines are discussed as examples. The effort is built around the introduction of the fire simulation computer program æVentgraphÆ to the Australian mining industry and the consequent modelling of fire scenarios in selected different mine layouts. Case studies have been developed to examine usage of inertisation units and particularly application of the GAG jet engine unit. One example has focused on selection of the best surface portal location for placement of the GAG for most efficient suppression of a fire. A second has examined a situation with significant seam gas being emitted on the face. This has shown that under certain face dip angles stopping the mine surface fan to reduce dilution of GAG exhaust gases will cause reversal of face air and consequent mine explosion as gas laden air is drawn across a fire. A third examines inertisation and dilution issues in mains headings. mains headings present a complex ventilation network with often numerous parallel headings, hundreds of cut-throughs and a variety of ventilation control devices. In such a complex system (with additional interference from a fire), maintaining control of the movement of inert gas is more difficult than elsewhere in the mine. Some illustrations of this issue are given.

Jan 1, 2005

By E E. Hall, C D. Taylor, D S. Yantek

Regular monitoring for methane gas is required near working faces in gassy underground mines where the potential for methane ignitions is greatest. However, high concentrations of methane can also accumulate outby the face where methane levels are monitored less frequently. Wearing a personal methane monitor equipped with an alarm could protect persons working in these outby areas from injury or death due to methane ignitions. The National Institute for Occupational Safety and Health (NIOSH) has conducted studies to evaluate methanometers that could be used as person-wearable monitors. For the present study, seven different person-wearable monitors that are not currently approved for underground use were evaluated. This paper describes test procedures used to evaluate performance of methane monitors that could be used underground for continuous personal monitoring of methane. The information in this report provides data that allows the reader to make side-by side comparisons of these instruments.

Jan 1, 2005

By Yuanbo Zhang

Keywords: Complex Iron Ores, Roasting, Tin, Zinc, Pellets, Comprehensive Recovery. The complex iron ores containing tin, zinc are typical refractory ores. Large reserves of the ores are found in China and have not been utilized efficiently so far. A new process of tin and zinc recovery and pellet preparation from iron concentrate containing tin and zinc by controlled atmosphere roasting is developed in this investigation. The results of 2573 N/P compression strength of product pellets, the 91.49% and 82.22% volatilization of tin and zinc respectively, are achieved for a concentrate containing 0.39% tin and 0.28% zinc. The strength and chemical compositions of the pellets meet the requirement of blast furnace ironmaking. Volatilization mechanism of tin and zinc are investigated. Thermodynamic study shows that the reduction balance curves of SnO2(s) and SnO(g) are proximate in the presence of carbon, and the standard formation free enthalpy of FeO and SnO2 is also approachable. Therefore, it is difficult to realize the complete volatilization of tin in the form of SnO(g) by selective reduction. But SnO2(s) and SnO(g) will form SnCl4(g) or SnCl2(g) in the presence of chlorides and can be easily volatilized from the ores.

Jan 1, 2005

By Roshan B. Bhappu

The extraction of gemstones, except for diamonds, continues to be a more or less handpicking type operation all over the world. However, considering the physical properties of gemstones such as density (sp.gr.), color, size, shape, luster, brilliance, reflection of light and the like in contrast to the relatively ‘dull’ physical characterization of the associated gangue minerals, it should be feasible to recover several gemstones using modern mineral processing techniques. This paper illustrates the unique physical characterization of several gemstones and suggests appropriate mineral processing techniques that could be used to recover these precious stones. Special emphasis is placed on the versatility of the Heavy Media Separation (HMS) process for processing of the gemstones. Finally, a few examples of commercially viable operations involved in the recovery of emeralds and rubies are presented.

Jan 1, 2005

By A Sinuhaji, H Kalangi, T B. Setyoko

Ore fragmentation at the DOZ block cave mine is highly variable, both as a function of rock type and column height of draw. Initially, the mine was constructed and equipped with limited capability to handle drawpoint oversize material. Significant issues with drawpoint availability and achieving overall mine production targets resulted. A suite of secondary sizing tools was added to the mine equipment fleet over a one-year time frame. Although significant oversize continues to be experienced, use of the correct secondary breakage tool for each particular oversize or hang-up occurrence has resulted in increased drawpoint availability, production rate, draw compliance, and operator safety. Currently, a range of secondary breakage techniques is being utilised to size material for delivery to the primary crusher. Run-of-mine material (3) is directly mucked to ore passes fitted with grizzlys that have one-metre square openings. Ore containing small boulders (>1 m3, 3) is loader-trammed to ore passes fitted with rockbreakers. Medium-sized boulders (>2 m3) accessible from the drawpoint are drilled with Sandvik Tamrock Commando drills. Boulders hung-up within the drawbell are drilled and charged with a Sandvik Tamrock Secondary Breakage Unit. Compacted, fine-grained muck is blasted utilising 55 mm cartridge powder concussion bombs.

Jan 1, 2005

By D. Song

In this paper, the differential equations governing the mass transport and the electrochemical reaction in a cathode catalyst layer of polymer electrolyte membrane fuel cells are solved based on the polynomial series expansion method. Explicit expressions for the polarization curve as well as for the distributions of oxygen, current density and overpotential are obtained when a quadratic, cubic or quartic polynomial is employed to approximate the oxygen concentration distribution. These kinds of explicit solutions are desirable for MEA design and diagnosis purposes. The comparison between the conventional numerical approach and the explicit solution approach proposed here shows that satisfactory accuracy can be reached by the first four terms of the polynomial series. The effect of the catalyst layer thickness on the accuracy of the obtained explicit polynomial solutions is also discussed.

Jan 1, 2005

By V. Badaker, R. J. Sweigard, C. D. Barton, J. W. Stringer, J. M. Ringe, A. D. True, D. H. Graves

Field studies have demonstrated the relationship between the growth of high-value trees on surface mined land and the physical conditions of the root growth medium. Specifically, the survival and height of hardwoods grown on less compacted material are far superior to those grown on compacted material. Furthermore, studies have demonstrated that the physical condition of the root growth medium can be characterized by dry bulk density and penetrometer resistance and that these parameters are also related to tree growth measurements. Site indices are useful for evaluating and predicting the productivity and timber yield for a specific location. A method has been proposed to estimate the site indices for various tree species on reclaimed surface mined land as a function of the physical properties of the root growth medium.

Jan 1, 2005

Good morning ladies and gentlemen, and may I extend a particularly warm welcome to our shores to those of you who have travelled from overseas to attend this conference. I trust that you will find your visit to New Zealand both rewarding and enjoyable.   This is now my fourth appearance at a New Zealand minerals conference, the second of which has been jointly co-hosted by AusIMM and Crown Minerals. Since taking on the role of Associate Minister of Energy, I have had the opportunity to meet most of the industry players, and to visit a good number of the major mining operations. Through all of this I have become increasingly aware of not only how dynamic the minerals and coal industry is but also the array of factors that affect investment decisions in this business. Many of these factors, such as commodity prices and availability of investment funds, are determined primarily on the international stage. Others however, such as the allocation, regulatory and the fiscal regimes for minerals, are closer to home and are directly influenced by government policy decisions. I will talk more on what the government proposes in this area shortly.   But first, I would like to commend you all on your industryÆs continuing contribution to New Zealand Æs economy. 2004 has seen New Zealand Æs mineral and coal output top $1 billion for the second consecutive year. To put this achievement in perspective, it represents a staggering 47 per cent increase over the national output value recorded just five years ago. Notable contributions over the year came from gold which increased production to 10.2 tonnes (up nine per cent), ironsand production at 2.3 Mt (a 20 per cent increase), and industrial rocks and building stones (up six per cent) with rock for building, cement and roading showing significant rises on the back of strong regional growth and infrastructure development. Many regions, in particular Auckland, Bay of Plenty, Wellington and Southland, recorded significant increased regional activity with supply often struggling to meet demand. By contrast the coal sector had a relatively steady year with production remaining stable at just over five million tonnes for the second year running. Coal exports however are now consistently exceeding two million tonnes annually, generating export earnings of over $200 million, and could well be higher with rail capacity improvements. Many countries throughout the world are now importing our high quality bituminous coal for steel manufacturing and other industrial uses.

Jan 1, 2005

By Steve L. Bessinger, Luis B. Giraldo, Joram Shenhar, James D. Pile

This paper discusses the Helical Drag Bit (HDB) and its rock drilling applications with an emphasis on use in mining operations. The HDB is a drilling tool that employs cutting members arranged in a pattern to form a helical groove or thread within a borehole. This pattern of cutters can be used for several purposes including roof bolting in mining, interpretation of the lithology of the strata being drilled and low energy consumption drilling. Laboratory and field experiments have consistently shown increase of roof bolt-anchoring capacities in weak rock of more than 100% using the short encapsulation pull test method when boreholes are conditioned using the HDB. In 2004 a series of tests conducted in mines with weak roofs demonstrated the benefits of HDB technology for roof bolting applications in mining. HDB technology offers opportunities for new and beneficial approaches to interpret the geology of roof strata. During conventional drilling, traditional approaches to determine rock properties require simultaneous measurement of several parameters such as thrust, rotational velocity, torque and penetration rate. The unique geometry of the HDB possesses a characteristic that allows determination of the mechanical properties of the rock being drilled by measuring torque as a single drilling parameter. This capability greatly simplifies the process of determining rock properties and provides reliable results. Additionally, HDB technology has been demonstrated to offer significant advantages for rock drilling. A substantial portion of the rock is removed by the fracturing of the internal thread created in the rock bore by the tool taking advantage of the weakness of the rock in tension. Because the rock chips obtained in this process are relatively large, savings in energy are realized when compared to traditional drilling technologies.

Jan 1, 2005

By Hajime Miki, Michael J. Nicol

Relatively simple techniques have been developed which enable the electrochemistry of sulfide minerals to be studied with particles varying in size from above 100 pm to less than 1 pm. Both oxidative and reductive processes have been studied wing the minerals pyrite, arsenopyrite and chalcopyrite. It has been shown that it is possible to completely oxidise or reduce the minerals during a single voltammetic sweep. The resulting voltammogram produces peaks which are characteristic of each mineral and can be used to qualitatively identify the minerals. In the case of chalcopyrite, it has been demonstrated that the charge involved in the anodic oxidation can be quantitatively related to the amount of copper dissolved. Quantitative information can be obtained using peak fitting techniques. Interesting differences in the behaviour of the minerals in sulfuric and hydrochloric acids have been observed, particularly in the case of pyrite for which a second major peak is obtained which has been attributed to the oxidation of elemental sulfur in the presence of chloride ions. The technique offers the possibility of providing mineralogical information of individual particles based on an electrochemical voltammetic finger print.

Jan 1, 2005

By Bill Cain, David F. Tsztoo, R. John Caulfield, D. Scott Kieffer

In 1994, the East Bay Municipal Utility District (EBMUD) commenced a system-wide Seismic Improvement Program to protect their facilities from catastrophic damage. A primary focus of this program has been on retrofitting the 75-year old Claremont Tunnel, which crosses the active Hayward Fault zone. A large earthquake on the Hayward Fault could generate enough right-lateral fault slip to effectively sever this important lifeline. The retrofit project involves construction of a new bypass tunnel through the Hayward Fault zone, together with systematic contact grouting and localized structural repair of the existing concrete liner. Several innovative design measures have been incorporated into the seismic retrofit design, including an oversized tunnel cross section, backfill concrete side drifts, seismic isolation of an internal structural pipe, and shear fuses in the final lining.

Jan 1, 2005

Agitation leaching data has generally not been analysed to extract the maximum amount of information that is available. Analysis of heap leaching systems has been developing over the last five years to include the underlying rate determining process. This has been found to be diffusion control for all copper leaching; irrespective of whether they are oxide or sulfide minerals. Extension of the diffusion model has enabled better scale-up protocols to be developed. Acid consumption in copper heap leaching operations has been found to be a first-order chemical controlled system. The analysis of the data is relatively straightforward. However the interpretation and scale-up is not as direct as for agitation leaching. The differences in the residence time distributions (RTDs) are required to properly account for the scale-up between test columns and field. The leaching of oxide copper in agitated systems has also been found to be diffusion controlled. However, there are significant differences in the control mechanisms. Initially the leaching control is the supply of acid to the mineral surface. This is limited by the diffusion through the surface boundary layer and is thus subject to the level of agitation. Higher agitation provides thinner boundary layers and faster diffusion rates. Similarly, higher grade material creates a thicker concentration boundary layer and relatively slower leaching. Acid consumption in agitated leach systems is also a first-order system. However, the interpretation of the RTD is easier from batch testing to continuous multiple CSTR series plant operations. Altering the method of acid delivery can significantly reduce acid consumption rates. Predilution of the acid minimises the local acid concentration near the addition point and can reduce the consumption by up to 50 per cent. Modelling of the combined leach rate(s) and acid consumption rates in agitated systems allows comparison of various leaching strategies and selection of the most appropriate. Similarly, the model allows the identification of economic limits to leach recovery; where the cost of acid consumption is greater than the value of the copper recovered. From this analysis selection of residence times for agitation leaching can be determined. The modelling tools are useful in identifying optimum conditions for the leaching process.

Jan 1, 2005

By T. Gerritsen, C. Martinez, F. Stober, T Ma, J. R. Frias, M. Sedighy, J. Janzen

Electrode control systems regulate power by physically positioning electrodes. Due to the weight and inertia of the electrodes and hoist equipment, this is a relatively slow process where power fluctuations of less than a few seconds are not fully corrected. Nickel laterite AC furnaces operating in high voltage, shielded arc mode typically incur frequent power variations of approximately +/- 20% or more around the power set point. To provide enhanced power control, Hatch has recently supplied, at commercial scale, a thyristor-switched reactance system called an SPLC. The SPLC incorporates predictive control software to operate furnaces at the maximum transformer rating by reducing the large power swings experienced without the SPLC. The resulting higher average power enables higher production, without increasing transformer or power plant capacity. A 60 MW production version of the SPLC has been commissioned on Falconbridge Dominicana's laterite nickel furnace, yielding excellent results with a 3 to 1 reduction in power fluctuations.

Jan 1, 2005

By P. Perruzza, R. Grandori, A. De Biase, A. Ciamei, A. Busillo

The Turin metro alluvium soil is mainly made of large boulders, cobbles and gravel , few sand and almost no fines. This grain size curve is out of the range of application for EPB and Slurry TBMs. In order to bore 5 of the total 7,5 kms of Line 1 tunnel, two specially designed Lovat EPB TBMs were utilised in combination with a systematic non structural pre-grouting of a small volume rectangular slab just above the tunnel section. The same pre-grouting was not however applicable for lack of access on surface in some sections of the remaining 2,5 km of tunnel that had to be bored below important buildings/structures, with under ground water pressure up to 1,5 bar, with curves radius of 180 m only. For these more critical sections it was necessary to study and implement a new technical solution and improve the capacity of the TBM to work efficiently in EPB mode even in this unsuitable ground and overall conditions. After months of studies the selected and adopted solution has been to inject inside the cutterhead chamber, in addition to the almost standard foams & polymers additive mixes, a suspension of limestone powders. This with the scope of compensating the lack of fines of the natural ground with rock powders.

Jan 1, 2005

By A. E. M. Warner

At the Copper Cliff Smelter, Inco Limited has extensive experience in converting primary smelting mattes over a broad range of nickel/copper ratios and compositions. In the past 35 years, technology developments at Inco have reduced the number of Peirce-Smith converters in Nickel/ Bulk (nickel-copper matte) service from 13 to the current 5. This paper will discuss: ? The performance and life of ?stretch? 13.7m shells versus conventional 10.7m converters. ? Process control and information system development from the early 1980?s to view converter aisle status on a continuous basis to the recent central control of the stretch shells. ? Nitrogen cooling of finishing matte from plant testing to implementation in the early 1990?s to replace the dedicated cooling converters. ? The impact on converting of changing the smelter flowsheet in the early 1990?s. ? A current program to develop a converting strategy for the future to address environmental issues and profitability.

Jan 1, 2005

By Jr. D'Angelo, Michael M. Blendy, Shawn Downey

"A grouted helical pile was used to support new buildings in the reconstruction of a large residential development. Foundation options were complicated by urban fill underlain with variable alluvial soil. A driven timber pile and grade beam system was recommended to support the new buildings. Other foundation options are also discussed. The grouted helical pile was quoted as an alternate and ultimately won the bid based on the economics and performance of the system. Data from 8 load tests was used to develop an empirical site specific relationship for determining pile capacity based on both installing torque and installation depth. Design to incorporate tolerance on installed pile location is presented. With the three phases completed, 554 residential dwelling units supported by 3645 grouted helical piles had been constructed covering 18 city blocks on the 44 acre site. IntroductionThe Philadelphia Housing Authority reconstructed the Tasker Homes housing complex located in southern Philadelphia, Pennsylvania, adjacent to the Schuylkill Expressway in the Grays Ferry area. Keating Building Corp. and Pennoni Associates were the general contractor and the structural engineer respectively. The original Tasker Homes development was constructed from 1940 to 1941 and consisted of 44 acres of primarily two and three-story residential brick buildings. These buildings were supported by a timber pile foundation system. The structural condition of the buildings supported on the timber piles was generally good in comparison to areas outside the buildings. These areas had settled possibly up to 2-feet in places due to the heterogeneous nature of the urban fill."

Jan 1, 2005

By V. Soloviev

The world?s data available on near sea-bottom gas-hydrate accumulation and deep-water fluid-discharge areas are presented in this paper. Gas-hydrate accumulation associated with fluid discharge (mud volcanoes, gas seeps, gas-saturated water seeps) is characterized by the following. First, the largest hydrate accumulations in sediments are located at shallow subbottom depths and have well-defined limits, especially in the upper subbottom part. Second, gas-hydrate formation in fluid-discharge areas is a present-day process, with the global occurrence of deep-water fluid-discharge areas numbering up to about ten thousand, and with all the seep areas being favorable for the formation of near-sea-bottom gas-hydrate accumulation. Third and principal, gas resources in the hydrates can be considered as renewable. Estimates of possible gas volume in single accumulations of hydrates and the global budget, as well as possible methods of gas utilization from such gas-hydrate accumulations are discussed in the paper.

Jan 1, 2005

By Joël P. T. Kapusta

Although Peirce-Smith converting remains the workhorse in matte converting, the copper and nickel industries are still confronted with production hindrances such as tuyere blockage, excessive refractory wear and limits in the oxygen enrichment levels of the blast air. The knowledge acquired on high-pressure gas injection technology as well as the invention of the concentric tuyere for steelmaking led to the development of the Air Liquide Shrouded Injector (ALSI) technology for copper and nickel converting. Following a technology demonstration in 1997-98 with four shrouded injectors installed in a Peirce-Smith converter, Falconbridge Limited implemented ALSI Technology on a commercial scale in May 1999 as an integral part of its new Slag Make Converter at Sudbury, Ontario, Canada. The paper presents the various aspects of commissioning ALSI Technology, as well as the operating changes and injector design modifications over the five years the shrouded injectors have been in operation.

Jan 1, 2005

By Glen Church, Don W. Deere, Christoph M. Goss

The Standley Lake Dam Rehabilitation Project in Colorado included the complete replacement of the outlet works. This required two 1.8m (6 ft) diameter microtunneled wet lake taps, 380m and 186m (1246 ft and 636 ft) long, a permanent valve shaft 12.2m(40 ft) wide and 32m (105 ft) deep, and a 3.5m (11.5 ft) diameter (962 foot long) outlet tunnel driven with a roadheader. The tunnels were driven in low-strength, expansive, and slickensided claystone. The paper addresses the site investigation, shaft construction, roadheader performance, shotcrete placement, tunnel convergence, long distance microtunneling, and wet lake taps.

Jan 1, 2005

By N. Loganathan, Tan Boon Tee, Joe O’Carroll, Richard Flanagan

In recent years, tunnelling activities in Singapore have increased considerably with the construction of extensions to the existing sub-surface transport system, a deep tunnel sewerage disposal system, and tunnels for the laying power cables and other utilities. These tunnels are excavated through urban areas, adjacent to high-rise buildings, depressed road structures, beneath other tunnels, and buried services. Earth pressure balance (EPB) tunnel boring machines (TBM) have been used extensively in Singapore with great success. The risk associated with soft ground tunnelling, including tunnelling through Old Alluvium, can be minimized with an understanding of the geology, geotechnical parameters, and the tunnelling-induced behaviour of Old Alluvium (OA The purpose of this paper is to present some design and construction aspects of EPB TBM tunnelling through Old Alluvium.

Jan 1, 2005