Search Documents

The aspect ratio (mill diameter/mill length) of autogenous and semi autogenous mills varies widely and can be as high as three or as low as 0.5. The literature on the subject of what effect aspect ratio has on grinding mill performance or energy efficiency is almost non-existent. However, at the design stage of many grinding circuits the subject is often vigorously debated amongst metallurgists. In this paper the performance characteristics of mills with different aspect ratios are examined to determine whether process performance characteristics are a function of aspect ratio and whether high aspect ratio mills are any more or less energy efficient than low aspect ratio units. Data from both pilot and full-scale mills are used for this purpose in open and closed circuit configurations.

Jan 1, 2007

By J. Font

New approaches for the fire refining process of blister copper have been carried out at the Codelco Norte Smelter. These have been mainly focused on modification and improvement of the process configuration based in fluid-dynamic and metallurgical studies of the oxidation and impurity treatment stages. This paper presents the results of the laboratory simulations and industrial tests performed in the 250 t anode furnace, evaluating two different process configurations: ? Bottom Bath Agitation System in the vessel during the oxidation stage, ? Dual Flux Injection System during the impurity treatment stage. The results show the possibilities of effective removal of high content of sulfur from the melt during the oxidation stage by using the bottom bath agitation. The use of the dual injection system demonstrated the significant improvement in the removal efficiency of impurities. Cu2007

Jan 1, 2007

By Gus Van Weert, Peter Kondos

"Ore sorting has been quite successful in providing a separation means in the rock size range of 1 to 6 inches; a range where mineral dressers do not have many options. The industrial minerals and recycling worlds have embraced this technology. However, ore sorting has not found wide application in the base or precious metals mining industry. One reason for this is thought to be the reliance of most sensors on rock surface characteristics, not very useful in case of sulphides, non-existing in case of gold. Microwave heating, however, is specific for sulphides and graphite (or carbonaceous matter) embedded in the rocks; washing or even drying does not appear necessary. Separation can be done afterwards by already existing ore sorting technology using infrared sensors. Test results on six Nevada gold ore samples are presented in detail. Some simple test procedures are also presented for those wishing to explore the microwave potential of sulphide sorting in their own operations.INTRODUCTIONMineral processing in the base metals industry most often involves upgrading of the ore, concentrating the valuable mineral fraction by classic methods, such as flotation. Since the liberation of minerals in the ore occurs mostly at or below the 100 micron level, the industry has been living with fault lines, so to speak, between blast hole spacing (10,000 mm), run-of-mine ore size (100 mm) and beneficiation size (0.1 – 0.01 mm). The acceptance of ore sorting will inevitably lead to the revisiting of the following questions: “Exactly how much below ore grade rock ends up in the mill because the geologists or the miners cannot define the resource boundaries more precisely? How can the economics of dilution be improved? How many ore grade rocks are lost with the overburden?”"

Jan 1, 2007

By K Komori

Naoshima Smelter and Refinery has treated shredder residue and incinerator fly ash in Japan since 2003. As a highlight, a new incinerating and melting furnace, as well as fly ash washing treatment plant were newly constructed for pre-treatment of shredder residue and fly ash respectively, and the pre-treated materials are ultimately treated in the existing Mitsubishi continuous copper smelting and converting process line. Since wastes such as shredder residue tend to vary in size and in shape, and contain some chlorine, the installation of a new pre-treatment line was required. The combination of the new pre-treatment line with the existing Mitsubishi Continuous Copper Process line has created a highly efficient and environmentally friendly system for recovering and recycling of valuable metals that previously used to be sent to a landfill. This paper reviews the approach that Naoshima took to establish its current recycling business strategy.

Jan 1, 2007

By Malcolm Ross

The Reserve Mining Co., in the processing of taconite iron ore quarried from the Peter Mitchell Pit, deposited the finely crushed waste rock into Lake Superior near Silver Bay Minnesota. In the early 1970s The U.S. Environmental Protection agency filed a lawsuit against Reserve Mining Co., asking the court to force the company to stop dumping into the lake. On April 20, 1974, after a lengthy court battle, the U.S. District Court concluded that the Reserve Mining discharge into Lake Superior violated federal and state pollution laws and thus ordered Reserve Mining Co., to halt the lake disposal of taconite tailings. At the time many feared that some of the mineral particles contained in the tailings (alleged to be asbestos or asbestos-like) would cause human health problems. This Conference was thus convened to readdress the problem of the mineral content of the Biwabik Iron Formation and to whether any minerals contained in the ore could cause human disease. The four papers given in this session address the nature of the mineral particles in the taconite rock, the definition of the term ??asbestos?? and the history of the legal controversy over the possible health effects of certain mineral particles contained in the Biwabik iron range ores. Paper 1?Geology of the Biwabik Iron Formation and Duluth Complex Mark A. Jirsa, James D. Miller, Jr., G.B. Morey The Biwabik Iron Formation was a principal source of ore for the American steel industry during the 20th Century. The unaltered iron deposits, called taconite, contain approximately 30% iron and 50% SiO2. About 75% of the iron in taconite resides in the mineral magnetite, the remainder is largely in iron carbonate and several iron-silicate minerals.

Jan 1, 2007

By A. Chryss, L. Pullum

Shear-thickening suspensions abound throughout the hydraulic conveying industry; at least this is the perception of many engineers running plants where hydraulic conveying is commonplace. In reality, shear thickening behaviour is limited, in the main, to high concentrations of fine particles, including colloidal and biological suspensions, at moderate to high shear rates. In the authors? experience most cases of shear-thickening behaviour have been either simple ?coarse? particle interactions, poor instrumentation techniques, or both. In some cases these were obviously heterogeneous flows, while in others flows that were homogenous, or were thought to be homogenous. Examples, which illustrate this erroneous perception are given. However, the trend towards pastes and complex suspensions that use high concentration carrier fluids means that the underlying slurries for many of these flows may now be truly shear-thickening. Unfortunately, suspensions that might exhibit shear thickening also invariably exhibit slip, or wall-particle depletion. These separate phenomena are difficult to resolve experimentally and many observations of apparent shear-thickening behaviour are in fact obscured or convoluted by slip effects. A method is presented whereby the true flow properties of these high concentration suspensions, and hence accurate prediction of pipeline flows, can be made using a parallel plate rheometer.

Jan 1, 2007

By William Hustrulid

Pre-split blasting is a primary technique for creating slopes with a minimum amount of unwanted damage to the remaining rock mass. Rock slopes created in such a way have both safety-related and economic advantages. The applications extend from road cuts to rock quarries to large open pit mines. For example, as deep open pit mines approach the end of their operating lives, slope steepening is one option to be considered. To be able to safely achieve and maintain steepened final slopes, good blast design techniques must be available and applied together with close operational control. Pre-split blasting is an important element in this slope creation process.

Jan 1, 2007

By J. A. Bakken, M. T. Jonsson, G. A. Saevarsdottir, H. Palsson

The electrodes of a Submerged Arc Furnaces carry a high current and are subject to enormous stresses caused by both the electric arc itself, and the current distribution within the electrode. The external effect of the arc on the electrode is treated in a different paper at this conference, The purpose of this paper is to analyze the thermal effects of ohmic heating within the electrode at the arc attachment on the carbon based electrode, using data for Søderberg electrodes. The thermal conditions are then used to examine stress conditions in the vicinity of an arc. Two types of models of an electrode are presented in the paper. The first type is an accurate finite element model, based on both two and three dimensional elements and the second type is an one dimensional model, providing better insight into the problem. For the second type, a spherical model of thermal conditions in a semi-infinite solid has been developed. Results show that the electrode surface is heated quickly up to a maximum temperature and for a specific test case, the surface can only withstand the load for about 10 seconds. Also, the thermal stresses on the surface are very high which will increase erosion on the surface in addition to normal evaporation.

Jan 1, 2007

By M-E Boucher

While the haematite concentrates produced in Eastern Canada and the magnetite concentrates that Australia will soon be producing are different feed materials, the pellets they produce have similar physical and metallurgical properties. This paper will examine the similarities and differences in the evolution of pellet microstructure for pellets produced from magnetite and haematite. The molten slag phase generated at high temperatures has a lower melting point when in contact with magnetite compared with haematite due to the higher divalent iron content. The presence of some slag is beneficial for bonding but too much can inhibit oxidation of magnetite, although slag generation at lower temperatures reduces energy usage. In pellets produced from haematite, magnetite is generated artificially from the combustion of the carbon particles added to the pellet feed as a source of energy. Maintaining the optimum production level and mineralogy of such æsecondaryÆ magnetite, allowing for its subsequent reoxidation, is important for the quality of haematite pellets. In both magnetite and haematite pellets, balancing the slag formation and oxidation (re-oxidation for haematite pellets) of the magnetite (secondary magnetite for haematite pellets) is necessary.

Jan 1, 2007

By Masanobu Masukawa, Toshio Shiota

The shaft-type ferromanganese smelting furnace (SF) at Mizushima Ferroalloy Co., Ltd. has been in operation since startup in 1985 and is continuing to perform smoothly. Production has been increased from the original design capacity of 270t/d to 350t/d by various operational improvements. As a productivity index of the shaft-type furnace, production of 350t/d is equivalent to productivity of 0.9t/m3/d (daily production/cubic capacity of furnace). Recently, various operational improvements were implemented to achieve productivity of 1.0t/m3/d or higher, including oxygen enrichment operation, increased tapping frequency, maintenance of the throat profile, and operation with small lump coke. The target productivity of 1.0 t/m3/d was achieved in January 2005. This report describes the improvements introduced as part of this high productivity technology.

Jan 1, 2007

By A Reid

The Late Archaean of South AustraliaÆs Gawler Craton contains significant potential for gold resources. The main targets of interest are migmatised gold style systems of which the Challenger deposit is the best known example. This deposit is one of the lower cost gold producers in Australia due to the high-grade, low-tonnage nature of the mineralisation. Structurally controlled, metamorphosed deposit styles are also possible throughout the Archaean of the Gawler Craton, including occurrences within reactivated shear zones. More typical, lower metamorphic grade orogenic gold styles are also possible within greenstone host sequences identified in the central and southern parts of the Gawler Craton.

Jan 1, 2007

By E. Dernedde

Cell rooms of aluminium smelters have large openings in the sidewalls and in the roof. These openings provide a high ventilation rate, which removes heat and contaminants emitted by the reduction cells and thereby ensures acceptable working conditions inside the cell room. However the large openings make the airflows through the smelter building sensitive to the wind. In this study equations for the airflow through the openings of a smelter building exposed to crosswinds were developed and verified against plant measurements. The equations were then used to estimate the airflows through a two-storeyed smelter building containing VS Soderberg cells. Wind protection by wind-covers over the sidewall openings and by upwind buildings made the airflows through the building less sensitive to the wind. Physical and mathematical modelling showed that working conditions inside the wind-protected cell room would be acceptable for crosswinds at speeds up to 16 km/h. These predictions were confirmed by measurements taken in a VS Soderberg smelter.

Jan 1, 2007

By V. McLemore, A. Fakhimi, K. Donahue, D. Sweeney, V. Viterbo

In order to evaluate the relationships between weathering and durability and strength of rock samples from the Goathill North rock pile at the Molycorp Questa mine, NM, we conducted slake durability and point load tests. Slake durability index (ID2) values ranged from 84 to 98%. Point load strength index (Is50) averaged for all rock units ranged from 1.1 to 5.7 MPa. Results show a slight positive trend between ID2 and paste pH. Two populations of data are distinguishable when ID2 is plotted versus the percentages of chlorite, illite and internal friction angle. In general, Is50 values increase toward the interior of the rock pile. Preliminary conclusions indicate that the durability and strength of the rock pile material generally increase toward the interior of the rock pile. Pre-rock pile alteration and post-rock pile weathering history have affected the durability of the GHN rock pile samples.

Jan 1, 2007

Mill liners provide the wear-resistant surface within grinding mills, they also impart motion to the mill charge, ie the grinding process, by providing the key between the charge and mill shell, and, at the discharge end, they remove the ground contents of the mill. As semi-autogenous grinding (SAG) mills have grown in size the process aspects of liner design and their impact on mill performance have become particularly important. While feedback from practical experience is critical to good mill liner design, increasingly sophisticated computer-based tools are being developed to assist in mill liner design.

Jan 1, 2007

By Ann Barron

Even though you think your company’s safety program is the best it can be, equipment, processes, supplies, surroundings and people do not always behave or react as expected. Consequently, needless accidents occur each year at quarries, construction sites, surface mines, and other locations where explosives are used. While blasting accidents account for only a small portion of the total accidents reported, the severity rate for blasting accidents is higher than for any other accident category.

Jan 1, 2007

By C. Yu, N. Topliffe, H. Song, W. Yu

The water separation pump is a highly effective alternative for medium pressure (1.6?6.4 MPa) slurry pumping requirements and has been widely used in industry since it was invented in the 1980s. The water separation pump is powered by a single or multi-stage clean water centrifugal pump. The water separation pump combines the advantage of high flow centrifugal pumps with the high pressure capability of reciprocating pumps. The clean water pressure is exchanged to slurry kinetic energy through the separating chamber, the principle component of the water diaphragm pump. Currently in its the third generation, the separation chamber uses a ball and flexible water seat that provides a true separation mechanism and can completely isolate the two fluids with near zero water loss.

Jan 1, 2007

By K. Blaski

his paper reports an investigation aimed at optimizing the compaction of granulated hard-metal powder for the production of cutting tool inserts. The optimal compaction is that which yields optimal shrinkage during sintering, i.e. minimum porosity in the sintered part. Extensive compaction tests on 23 different hard-metal powders have been carried out and have shown that the ideal ?green density? of a hard-metal compact, i.e. the density after compaction, increases linearly with the apparent density of the powder. On the basis of this result, an equation has been derived, which allows one to predict the optimal shrinkage that a hard-metal compact undergoes during sintering once the following data are known: the required sintered density, the volatile content of the powder and the apparent density of the powder. Since these data are available to the tooling designer, this equation allows one to design tooling for the compaction of hard-metal, which leads to optimal shrinkage

Jan 1, 2007

By J. S. Edwards

The ISASMELT? process is recognized worldwide as a modem, flexible, environmentally-friendly and low capital cost smelting technology. Due to the inherent simplicity, and the advanced process control that has been developed, personnel become competent within weeks of being introduced to the ISASMELT? technology. This compares with the years required to become proficient with alternative technologies. Copper smelters in Australia, USA, India, China, Peru and Zambia have installed ISASMELT? technology under licence from Xstrata Technology. In the secondary copper business, plants in Belgium and Germany are processing copper and/or lead materials in ISASMELT? furnaces in a two stage process. In a single furnace smelting is followed by converting. Both plants have exceeded design capacities and are continuously improving their performance. The next evolutionary step for the technology is the implementation of the continuous copper converting process on a commercial scale. The present work describes the design status of the continuous converting process - ISACONVERT?.

Jan 1, 2007

By E. Jackson

This paper describes highlights of the Placer Dome MiniMole project - the development and testing of a robotic machine for mining narrow ore veins. A prototype hydraulically controlled robotic machine was built and tested. The machine provided a platform for testing numerous cutters in the field. Other cutters, e.g. undercutting devices, were tested in the lab. Extensive analyses were done on specific energies and cutter penetration. Three sets of quarry trials were done, then the machine was tested in an underground mine. Rock UCS values varied from 180 MPa to 230 MPa. The paper includes lessons learned and recommendations based on the project findings.

Jan 1, 2007

By L. Contretras

This study has as an objective to analyze and to propose actions to improve the quantity and quality of the graduate education in the area of mining industry, specifically of mining engineers, metallurgists, geologists, to satisfy the expectations of professionals in the mining industry. Included are an analysis of the present scenario and the future demands in countries like Chile and proposed plans for the Establishment of Educational Initiatives, country policies and market forecast, vis-a-vis the experience of Australia, South Africa, United Kingdom, Canada and the United States of America.

Jan 1, 2007