Search Documents

By Gokhan Inci

Stability problems with dam spillways on existing landslides and appropriate mitigation measures to remedy them are ongoing concerns for geotechnical engineers. The first successful application of drilled piers as stabilizing structures under the spillway was at the Trinity Dam in Sicily, Italy. ?Underpinning? was considered as an alternative to spillway relocation during the Alpaslan 2 embankment dam design in eastern Turkey. Based on the available literature the first application of drilled piers to stabilize a spillway chute in the U.S. was at the Ralston Dam in Colorado. Ralston Dam, which is a 175-foot-high zoned fill dam located 15 miles northwest of downtown Denver, was built in the late 1930s. The concrete spillway for the dam was built on the Pierre Shale Formation in the left abutment. Since reservoir operations began, mass movements have occurred downstream of the chute area. These movements have required periodic spillway maintenance. After the occurrence of recent movements and because of high piezometeric levels, URS was contracted by Denver Water to develop a more permanent solution by the installation and monitoring of additional instrumentation, analysis of slope stabilizing measures, design, repair, and reconstruction of the distressed section of the spillway chute. With state of the art modifications that include: 1) a stabilizing berm with a toe trench that improves the global stability; 2) seepage prevention and control measures that prevent the infiltration of water; and 3) the structural support of the replaced chute section with drilled piers and reinforced concrete the probability of future displacements or other problems have been reduced for the Ralston Dam Spillway.

Jan 1, 2007

By F. Flores

With the World Summit for Sustainable Development planned for 2002 in mind, nine of the world's largest mining companies decided to initiate a project to examine the role of the minerals sector in contributing to sustainable development, and how that contribution could be increased ? the Mining, Minerals and Sustainable Development Project (MMSD). This project assumed from the start that sustainable development could provide a useful framework to guide the minerals sector which main goal was integrating economic activity with environmental integrity, social concerns, and effective governance systems. The broad steps of MMSD project strategy can be grouped into four major categories: increase understanding of sustainable development; create organizational-level policies and management systems for implementing the principles of sustainable development; collaborate with others with common interests to take joint steps towards sustainable development, and; increase our ability to work towards sustainable development at the local, national, and global levels. In opinion of the article's author, to go ahead with the MMSD strategy and achieving the sustainable development objectives, it is necessary to consider the concept of self-organization, fundamental of the emergent new scientific paradigm, and the consequent epistemology and values that conform a supporting culture for sustainable development.

Jan 1, 2007

By M. Wu, X. Zhao

This paper presents an integrated pipeline transport system for thickened coal sludge, which combines pretreatment and pipeline transport with combustion techniques of thickened coal sludge. The pipeline can transport thickened coal sludge with a sufficiently high solids content (about72%?77%) and high apparent viscosity (about 1 000Pa?S?3,000 Pa?S) directly by pipeline having neither use for water nor an addition agent. The transport distance can be as high as 1 000 metres. In particular, the operating principles, key equipment and technical parameters of this integrated system are examined in this paper. The integrated system effectively causes no pollution to the environment because it is completely sealed, and conserves energy over traditional conveyer designs. Keywords: pipeline transport; integrated system; circulating fluidized bed boiler; thickened coal sludge; high solids content

Jan 1, 2007

By Khamis Y. Haramy

Curing temperature, density, and moisture significantly affect the velocity measured in the crosshole sonic logging, the rate of strength gain, and the final strength of concrete in drilled shafts and, thereby, affect their structure capacities. Non-destructive field measurements can enhance the QA/QC program by measuring temperature, density, moisture, and sonic velocity of curing concrete during the construction and curing of drilled shafts. The curing environment can greatly affect the concrete strength, and requires close attention during construction. This article shares the experience with the NDE technology used in the QA/QC program in the drilled shaft construction. To understand the mechanism by which a drilled shaft cures under field conditions, two newly constructed drilled shafts were monitored for up to seven days, immediately following concrete placement using the following geophysical logging methods: a) temperature logging; b) crosshole sonic logging; c) gamma-gamma density logging; and d) neutron-moisture logging. One additional drilled shaft was also monitored to a shorter duration. Temperatures were monitored using the sensor in access tubes and/or thermocouples embedded at the center of a drilled shaft and near its reinforcing cage. For a small shaft under 1m diameter, curing temperatures appeared to peak at 41° ? 68° C at different depths at around 24-hour curing time and decreased to and stabilized at around 23° ? 35° C in 6 days. The shaft curing rate varied with depth, shaft diameter, surrounding geo-material types, and the depth of ground water. CSL logging was performed in one shaft from top to bottom from six access tubes and limited monitoring in another shaft. The velocity increased with curing time till 4 to 7 days, and, at a specific time, the velocity appeared to be inversely correlated to curing temperatures. The gamma-gamma density log (GDL) results from 5 different depths were obtained at a source-detector separation of 355 mm. The average density was found to increase with curing time, but decrease slightly in 3 to 5 days. At a given time the GDL density curves seemed to correlate with the neutron monitoring logging (NML) moisture curve. The NML moisture was monitored from 1st to 6th day after concrete placement. The moisture was highest when surrounded by bedrock, then clay, and sand due to different hydration rates.

Jan 1, 2007

By N. Bakhshizadeh

In this investigation, the aging effect on creep behavior of A12024-10%SiC composite fabricated by powder metallurgy was studied. P/M bars were manufactured by hot powder extrusion method at 450°C with a ratio of 16 to 1. Creep specimens were over-aged at 187 ºC for 43 h. It was found that almost full density composite with relatively homogenous distribution of reinforcing particles throughout the aluminum alloy matrix could be attained by direct powder extrusion process. Creep tests were conducted at temperatures from 275 to 325°C under stresses from 25 to 60 MPa. The analysis of the creep mechanism determined that dislocation glide was the predominant mechanism of plastic deformation. The activation energy of the creep process was found to be higher than that of lattice self-diffusion in pure aluminum.

Jan 1, 2007

By K. H. Al-Rawahy

Appreciation and awareness of the unique nature of mineral investment and ultimate development of a mine are crucial in promoting sustainable development. Special characteristics of mineral development include high capital intensive, long pre-production period, high risk, and the unavoidable ?economic? depletion. This paper examines ways to integrate these unique attributes of the mineral industry into the educational process, so that a properly advised and knowledgeable culture in terms of a sustainable mineral industry can be developed. Specific approaches are investigated in order to achieve this objective. These include a stochastic evaluation of a mineral investment proposal, adding a premium to the cost of capital that is used for valuation process, and internalizing incidental costs to the private cost function, thereby realizing the true (vs. apparent) marginal social cost of the proposed development. Undoubtedly, a total evaluation of any mineral project that accounts for both tangible and intangible parameters will contribute to sustainable development objectives. By incorporating the practical application of apparent theoretical topics such as risk, probability, and externality, and their relevance and impact on mineral lifecycle (prospecting, exploration, development, exploitation, use, and ultimate disposal) into the educational process, it is hoped that a generation of technocrats and decision makers that are familiar with and concerned about sustainable development will emerge.

Jan 1, 2007

By Namavari. H., M. Ashouri, M. R. Sarhadi, S. H. Mansouri, A. Sarrafi

The splash phenomenon and its effective parameters in metallurgical converters have been studied thoroughly for decades. The detailed studies of processes such as tuyere blockage, wave formation during air injection, entrapped phases, and also processes which control the formation of bubbles in viscous fluids are not feasible yet. In this research, we have used a converter-shaped vessel made of flexi-glass. Water and oil have been used as matte and slag phases respectively. The effective operational factors responsible for creation of splashing have been studied such as air flow rate, tuyere angles, depth of tuyere submergence, tuyere blockage, density and viscosity of liquids, liquids heights, etc. The results have been found as follows: the amount of splashing increases slowly as air flow rate increases. However, as the air flow rate reaches a critical value (depending on the physical specification of converter) the amount of splashing rises sharply, because the flow of air inside the liquid changes from bubbling into a jet stream; and most of the splashed materials are in the form of filaments instead of droplets. Changing tuyere angle from horizontal towards vertical position will increase the turbulence level on the fluid surface and causes an increase in the amount of splashing. The effect of tuyere submergence is related to the converter opening angle. As the converter opening angle is shifted towards the hood position, the amount of tuyere submergence and splashing will increase. As density of the liquid increases, the number of droplets splashing increases with a decrease in drop size. Therefore, the total amount of splashing decreases. However, as viscosity of the liquid increases, the splashing material increases due to the changes in the splashed material from droplet shape into filament form. The height of liquid inside the converter, depending on the relative height of heavy phase and light phase, is an important parameter regarding splashing. As the relative height of heavy phase to light phase increases the splashing will decrease. The tuyere blockage will cause the pressure in the inlet manifold to increase; and in real cases will increase the splashing. Finally, we have development a model based on dimensional analysis to relate the above parameters in order to calculate the amount of splashed material.

Jan 1, 2007

By Ben Hayes, Michael Ryjevski

The Palm Jumeirah is the smallest of the three Palm Islands (Palm Jumeirah, Palm Jebel Ali and Palm Deira). It is located on the Jumeirah coastal area of the emirate of Dubai, in the United Arab Emirates (UAE). The unique man made island is built in the shape of a date palm tree and consists of a trunk, a crown, 17 fronds and a surrounding crescent island that will form a breakwater. The Jumeirah Palm Island is primarily are treat and residential area for living, relaxation, and leisure. It will contain themed boutique hotels, three types of villas, shoreline apartment buildings, beaches, marinas, restaurants, cafes and a variety of retail outlets.

Jan 1, 2007

By T. Beamish, I. Vasilev, T. Nikolov, E. Marinov, D. Kirilov, P. Barrios

In April 2005, Umicore Copper de-merged from Umicore Group and created a new independent Copper company called Cumerio. As a separate company, Cumerio is a major European copper smelter and refinery and a leading producer of copper products such as wire rod, billets, cakes and specialty rod with a total production capacity of copper products in excess of 500,000 tpy with production plants in Belgium, Italy and Bulgaria. The Pirdop Smelter is the only state-of the-art smelter in South East Europe and it makes Pirdop the natural hub for the copper industry in the region. In order to be competitive in the international market the main challenges facing Cumerio are to maintain its low cost structure and to achieve higher production volumes while reducing its impact to the environment and striving for continuous improvement of the production process. Cumerio's state-of-the-art smelting facility in Pirdop has recently increased the anode production capacity to 250,000 tpy by the installation of the third evaporative cooler on the converters section that allows operating with three-hot converters. In April 2007 a general shut-down for repair and modification on the Flash Smelting Furnace and Waste Heat Boiler is envisaged. At this time a revamp of one of the existing Sulphuric Acid Plants is planned, resulting in a further copper capacity increase to 275,000 tpy with modest Capex. In 2005 Cumerio received from the Bulgarian Ministry of Environment and Water the Complex Permit under the EU IPPC criteria. Accordingly an Environmental Compliance Program was defined targeting a large reduction in the secondary emissions. The system will be commissioned in May 2007. In order to better integrate the smelter and refinery in Pirdop and to respond to the growing demand for cathodes in the region, a new state-of-the-art Electrolytic Refinery with an installed capacity of 180,000 tpy will replace the existing refinery. The new refinery is expected to be fully operational as from early 2008. This paper describes the challenges and the projects.

Jan 1, 2007

By S. Watkins, D. Apel, B. Gray, R. Moss

Currently, there are several techniques and technologies available which are used by mining industry in its attempts to remotely monitor the ground movements both at surface and underground mines. The currently available remote distance meters and distance change monitors mainly use phase change and time-of-flight techniques. The described monitor uses triangulation technique to track position of an optical spot projection and then image processing to measure mine wall movements. The system can be easily automated and poses no obstruction to mine traffic. The position of an off-normal laser spot will shift as the target wall moves. The described ground movement monitoring system has potential for superior accuracy and target monitoring can be made through air (gaseous) or other transparent media. The theoretical accuracy and range of this system depends solely on the resolution and focal length of the camera being used. The remote capabilities of the system make it uniquely suited to applications where monitoring is required in high-traffic, inaccessible, or unstable and dangerous areas of a mine.

Jan 1, 2007

By P. Goosen

The paper presents a basic summary of the approach to hydraulic scale-model tests as may typically be applicable to slurry flow situations. A case study is presented illustrating how hydraulic scale-model tests can be of significant benefit in evaluating the performance of novel or unproven slurry handling equipment. In this case the equipment tested was a fan-shaped expansion piece used to spread the discharge from a launder over the full width of a dewatering screen. The tests showed that the device did indeed distribute the slurry flow both in terms of volume and solids mass, but not perfectly uniformly. Unfortunately the equipment was not taken beyond the model test phase. The scale-model test approach did, however, prove to be very useful as it is considered to have provided a good indication of the expected performance of the full-size unit. Significantly, this was achieved at very low cost compared to the cost of installing the device into the proposed plant and having to later change it out for an alternative or live with the less than optimal performance. The paper illustrates the value that can derive from applying hydraulic scale-model testing techniques to evaluating the performance of new or unusual slurry handling equipment. There is particular value in situations that do not lend themselves to numerical modelling.

Jan 1, 2007

By Bernard H. Hertlein

The introduction of LRFD methods for structural design has been a gradual process by AASHTO, ACI, AISC, ASCE, and the FHWA, which has largely been ignored by the deep foundations industry. In 2007, however, the industry has been obliged to embrace LRFD for any deep foundations on projects involving federal funds. The authors are concerned that the risks caused by the need for, and the difficulty of providing, reliable quality assurance, will result in unnecessarily high safety factors that will defeat part of the purpose of LRFD. A primary attraction of LRFD for owners and engineers alike is that it promises more efficient design, and therefore cost reductions. Unfortunately, a key element of LRFD philosophy is often overlooked - that the applied safety factors can be rationally reduced, often allowing less material to be used, thus saving costs, but only if all the risk factors involved are identified and closely controlled. This means that both the quality of the materials and the quality of the construction work must be adequately monitored, and held to an acceptable standard. In the case of deep foundations, the soil in which the foundation is constructed is also a critical component that must be taken into account in the assessment of risk factors.

Jan 1, 2007

By V. G. Pienaar, B. M. Mbiya, P. T. Slatter

[a constant b constant cc onstant c' constant D pipe diameter (m) Dshear shear diameter (m) E error function fth theoretical friction factor F function F' function K fluid consistency index (Pa sn) kv valve loss coefficient L pipe length (m) n flow behaviour index N number of data points ?P valve pressure drop (Pa) Q flow rate (m3/s) Re Reynolds number Re3 Reynolds number (Slatter) V average velocity (m/s) Vann annulus velocity (m/s) x variable X number of independent variables y variable Y number of fundamental dimensions z variable µeff effective viscosity (Pa s) ? valve degree of opening d partial derivative ? fluid density (kg/m3) [ ] function]

Jan 1, 2007

By E. Esmaeilzadeh

There arc 8 primary ball mills in the concentrator plant and their task is material crushing. At the time of balls charge to mills, a lot of noise is produced. This noise would affect all grinding areas. The aim of this research was a reduction about 16 dB at source sound power level (SWL was 129.1 dB). With considering two noise control principles, noise producer sources and propagation paths were specified. For removing and reducing of noise producer sources, rubbers with a thickness of 5-20 mm were used on the all inside surfaces of charge box, ball transferring box and exit canal. For increasing transmission loss and damping coefficient of charge box body, rubber with thickness of 1 cm at outside surface of box was used. For reduction of noise propagation a secondary metal cover was designed and made. This cover includes two parts and was set around the charge box. Glass wool (75 kg/m3) with 10 cm thickness was used as acoustical absorbent between free space of two body's layers and from secondary cover side. The of the rest space was left empty. After installing of secondary cover on the ball charge box no.4, SWL showed a reduction about 16 dB. For studying of control system effect on noise reduction at points far from of charge place, measuring results at these points showed the maximum reduction 12.1 dB and the minimum 11.8 dB.

Jan 1, 2007

By D. Royston

Mill liners provide the wear-resistant surface within grinding mills, they also impart motion to the mill charge, ie the grinding process, by providing the key between the charge and mill shell, and, at the discharge end, they remove the ground contents of the mill. As semi-autogenous grinding (SAG) mills have grown in size the process aspects of liner design and their impact on mill performance have become particularly important. While feedback from practical experience is critical to good mill liner design, increasingly sophisticated computer-based tools are being developed to assist in mill liner design.

Jan 1, 2007

By C. Caballero, M. Rosales, C. León, A. Valencia, R. Fuentes, A. Moyano

Slopping is the formation of waves in the converter due to the gas injection by tuyeres. Those waves produce a premature wearing of the refractory lining of the reactor due to its great amplitude. The affected zones are the tuyere line (outlet gas from tuyeres) and the front of this line. In the present work, a theoretical and experimental study is made to develop a theory that determines the variables involved in slopping, characterizing the more important parameters of operation in the phenomenon of slopping. In addition, this theory will allow for determination of new technological alternatives of the blast injection permitting to depress the slopping phenomenon.

Jan 1, 2007

By G D. Cooper

There are no manuals or handbooks for budding mill superintendents or process plant managers. Most who obtain this level of responsibility have gained their training from watching the good and bad of their predecessors and the successful ones have themselves graduated from the school of hard knocks. This paper attempts to provide some helpful guidelines and direction for those who aspire to better manage a mineral processing facility. The authors have 20 years combined experience in senior management roles at nine different mineral processing operations in Australia and overseas, covering gold, base metals and mineral sands. This summary of tips and pitfalls will hopefully benefit future leaders in mineral processing and metallurgy.

Jan 1, 2007

By A. M. Esteves

This paper addresses the question ?What constitutes the right level of investment in community goodwill?? Mining companies are still grappling with this subject even though the business case for community investment has been accepted at a general level, as a strategy for competitive differentiation, risk mitigation and a desire to deliver - and to be seen to deliver - a ?net benefit? to affected communities. Gaining senior management commitment to long term social projects, by definition characterized by uncertainty and complexity, is made easier if projects are shown to benefit the site?s strategic goals. Case study research amongst mining companies, including interviews with social investment decision-makers, has assisted in developing a SI-DAT (Social Investment Decision Analysis Tool), a decision model for evaluating social projects in order to create value for both the company and community. Multi-criteria decision analysis techniques integrating business planning processes with social impact assessment have proved useful in assisting mining companies think beyond seeking access to required lands and peaceful relations, to how they can meet their business goals and contribute to regional development.

Jan 1, 2007

By Taehong Kim, Carl Pannuti, Nikolas Sokol, Walter Herrick

BACKGROUND This paper discusses work performed as part the rehabilitation of the gravity flow section of the New Croton Aqueduct (NCA) during an approximately two year period between 2004 and 2006. The goal of the project was to restore the gravity flow section of the NCA to optimal operating condition, extending the lifespan of this significant water supply for the New York City metropolitan area. Rehabilitation of the NCA was purposely scheduled before the completion of the new NCA Water Treatment Plant now under construction (Figure 1). The NCA is a 3.73 to 4.34 m (12.25 to 14.25 ft) diameter brick-lined circular andhorseshoe shaped water tunnel constructed between 1885 and 1891. The NCA conveys water for approximately 50 km (31 miles) by gravity and pressurized flow from the New Croton Reservoir in Westchester County, NY to distribution and reservoir points along its alignment, terminating at a distribution station at 135th Street and Convent Avenue in Manhattan, NY. Prominent features of the NCA include a large intake facility at New Croton Reservoir, 38.6 km (24 miles) of gravity flow horseshoe shaped aqueduct, 11.3 km (7 miles) of pressurized flow circular aqueduct, 2 siphons, and 36 open shafts and headhouse chambers which are used as sampling, access and blow-off locations. Until a partial inspection in 1982, the NCA had flowed continuously since its completion nearly 100 years prior. Flow tests have confirmed that the NCA can convey up to 12.7 m3/s (290 mgd) (Figure 2). Cover depths of NCA vary considerably, ranging from a few to hundreds of meters, typically of hard rock. Primarily mined using means conventional for the late1800s, construction of the NCA also employed cut and cover methods in several low-lying sections of the alignment, totaling approximately 1.6 km (1 mile). The NCA crosses through numerous lithologic changes, fault/shear zones and under several significant water bodies including the Pocantico, Saw Mill and Harlem Rivers and the Tarrytown Reservoir. The NCA passes under the Harlem River as a siphon at a depth of approximately 122 m (400 ft) below grade (Figure 3). Soon after construction the Aqueduct Commission Reports on the New Croton Aqueduct documented prominent defects such as large voids behind the lining. More recently, large-scale inspections of the gravity flow section performed during the 1990sand a 2004 inspection of portions of the pressurized sections of the NCA have revealed additional defects such as open and/or deteriorated masonry joints/cracks, leaks ranging from trickles to several liters per minute into and out of the NCA, missing bricks, formed openings, and in one place, a rupture through the liner with discernable

Jan 1, 2007

By Anthony K. Anyimadu, Chris M. Rule

Froth flotation is the primary mineral processing separation step employed in the beneficiation of PGM ore bodies. Anglo Platinum operates a significant portion of the total installed flotation capacity in the PGM industry, which is installed at 20 operating plants across the Bushveld. PGM flotation has undergone a considerable evolution in both the capacity of flotation cells employed as well as in the circuit design configuration over the past thirty years. Certain of Anglo Platinum?s flotation circuits have been in operation for a relatively long period of time, (in some operations installed equipment dates from the 1960?s) and this allows comparative operating performance between various equipment types and circuits to be evaluated. This paper summarizes some aspects of this experience. Research trends in flotation are continuously monitored to incorporate appropriate findings into existing and future circuit designs. Continuous evaluation and monitoring of flotation performance is undertaken to identify opportunities for increasing flotation efficiencies. Mineralogical and fractional analyses of plant composites and survey samples are analysed to interrogate speciation and association data. This analysis has enabled a better understanding of priorities and opportunities for improved metallurgical performance. These opportunities are divided into three improvement areas: stability, liberation, and fines flotation. The paper discusses these, as well as the circuit design improvements required to take full advantage of the opportunities identified.

Jan 1, 2007